| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Synopsys DesignWare XPCS IP-core can be synthesized with the device CSRs
being accessible over the MCI or APB3 interface instead of the MDIO bus
(see the CSR_INTERFACE HDL parameter). Thus all the PCS registers can be
just memory mapped and be a subject of the standard MMIO operations of
course taking into account the peculiarities of the Clause C45 CSRs
mapping. From that perspective the DW XPCS devices would look as just
normal platform devices for the kernel.
On the other hand in order to have the DW XPCS devices handled by the
pcs-xpcs.c driver they need to be registered in the framework of the
MDIO-subsystem. So the suggested change is about providing a DW XPCS
platform device driver registering a virtual MDIO-bus with a single
MDIO-device representing the DW XPCS device.
DW XPCS platform device is supposed to be described by the respective
compatible string "snps,dw-xpcs" (or with the PMA-specific compatible
string), CSRs memory space and optional peripheral bus and reference clock
sources. Depending on the INDIRECT_ACCESS IP-core synthesize parameter the
memory-mapped reg-space can be represented as either directly or
indirectly mapped Clause 45 space. In the former case the particular
address is determined based on the MMD device and the registers offset (5
+ 16 bits all together) within the device reg-space. In the later case
there is only 8 lower address bits are utilized for the registers mapping
(255 CSRs). The upper bits are supposed to be written into the respective
viewport CSR in order to select the respective MMD sub-page.
Note, only the peripheral bus clock source is requested in the platform
device probe procedure. The core and pad clocks handling has been
implemented in the framework of the xpcs_create() method intentionally
since the clocks-related setups are supposed to be performed later, during
the DW XPCS main configuration procedures. (For instance they will be
required for the DW Gen5 10G PMA configuration.)
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the next commits will alter the DW XPCS driver to support setting a
custom device ID for the particular MDIO-device detected on the platform.
The generic DW XPCS ID can be used as a custom ID as well in case if the
DW XPCS-device was erroneously synthesized with no or some undefined ID.
In addition to that having all supported DW XPCS device IDs defined in a
single place will improve the code maintainability and readability.
Note while at it rename the macros to being shorter and looking alike to
the already defined NXP XPCS ID macro.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DW_2500BASEX case in xpcs_get_state( ) to update speed, duplex and pause
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231027044306.291250-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wangxun NICs support the connection with SFP to RJ45 module. In this case,
PCS need to be configured in SGMII mode.
According to chapter 6.11.1 "SGMII Auto-Negitiation" of DesignWare Cores
Ethernet PCS (version 3.20a) and custom design manual, do the following
configuration when the interface mode is SGMII.
1. program VR_MII_AN_CTRL bit(3) [TX_CONFIG] = 1b (PHY side SGMII)
2. program VR_MII_AN_CTRL bit(8) [MII_CTRL] = 1b (8-bit MII)
3. program VR_MII_DIG_CTRL1 bit(0) [PHY_MODE_CTRL] = 1b
Also CL37 AN in backplane configurations need to be enabled because of the
special hardware design. Another thing to note is that PMA needs to be
reconfigured before each CL37 AN configuration for SGMII, otherwise AN will
fail, although we don't know why.
On this device, CL37_ANSGM_STS (bit[4:1] of VR_MII_AN_INTR_STS) indicates
the status received from remote link during the auto-negotiation, and
self-clear after the auto-negotiation is complete.
Meanwhile, CL37_ANCMPLT_INTR will be set to 1, to indicate CL37 AN is
complete. So add another way to get the state for CL37 SGMII.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable CL37 AN complete interrupt for DW XPCS. It requires to clear the
bit(0) [CL37_ANCMPLT_INTR] of VR_MII_AN_INTR_STS after AN completed.
And there is a quirk for Wangxun devices to enable CL37 AN in backplane
configurations because of the special hardware design.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching interface
mode.
If the interface changes, the following setting is required:
1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good)
2. write SR_XS_PCS_CTRL2 to select various PCS type
3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed
4. program PMA registers
5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific
Soft Reset)
6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared
Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun
devices. And there is a quirk for Wangxun devices to switch mode although
the interface in phylink state has not changed, since PCS will change to
default 10GBASE-R when the ethernet driver(txgbe) do LAN reset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read the clause 73 link partner advertisement in a loop and then
translate to the ethtool modes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For CL37 1000BASE-X AN, DW xPCS does not support C22 method but offers
C45 vendor-specific MII MMD for programming.
We also add the ability to disable Autoneg (through ethtool for certain
network switch that supports 1000BASE-X (1000Mbps and Full-Duplex) but
not Autoneg capability.
v4: Fixes to comment from Russell King. Thanks!
https://patchwork.kernel.org/comment/24894239/
Make xpcs_modify_changed() as private, change to use
mdiodev_modify_changed() for cleaner code.
v3: Fixes to issues spotted by Russell King. Thanks!
https://patchwork.kernel.org/comment/24890210/
Use phylink_mii_c22_pcs_decode_state(), remove unnecessary
interrupt clearing and skip speed & duplex setting if AN
is enabled.
v2: Fixes to issues spotted by Russell King in v1. Thanks!
https://patchwork.kernel.org/comment/24826650/
Use phylink_mii_c22_pcs_encode_advertisement() and implement
C45 MII ADV handling since IP only support C45 access.
Tested-by: Emilio Riva <emilio.riva@ericsson.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NXP SJA1110 switch integrates its own, non-Synopsys PMA, but it
manages it through the register space of the XPCS itself, in a small
register window inside MDIO_MMD_VEND2 from address 0x8030 to 0x806e.
This coincides with where the registers for the default Synopsys PMA
are, but the register definitions are of course not the same.
This situation is an odd hardware quirk, but the simplest way to manage
it is to drive the SJA1110's PMA from within the XPCS driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NXP SJA1105 DSA switch integrates a Synopsys SGMII XPCS on port 4.
The generic code works fine, except there is an integration issue which
needs to be dealt with: in this switch, the XPCS is integrated with a
PMA that has the TX lane polarity inverted by default (PLUS is MINUS,
MINUS is PLUS).
To obtain normal non-inverted behavior, the TX lane polarity must be
inverted in the PCS, via the DIGITAL_CONTROL_2 register.
We introduce a pma_config() method in xpcs_compat which is called by the
phylink_pcs_config() implementation.
Also, the NXP SJA1105 returns all zeroes in the PHY ID registers 2 and 3.
We need to hack up an ad-hoc PHY ID (OUI is zero, device ID is 1) in
order for the XPCS driver to recognize it. This PHY ID is added to the
public include/linux/pcs/pcs-xpcs.h for that reason (for the sja1105
driver to be able to use it in a later patch).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vendors which integrate the Designware XPCS might modify a few things
here and there, and to support those, it's best to create separate C
files in order to not clutter up the main pcs-xpcs.c.
Because the vendor files might want to access the common xpcs registers
too, let's move them in a header file which is local to this driver and
can be included by vendor files as appropriate.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
