| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 3178d2b048365fe2c078cd53f85f2abf1487733b ]
xa_alloc_cyclic() can return 1, which isn't an error. To prevent
situation when the caller of this function will treat it as no error do
a check only for negative here.
Fixes: 384968786909 ("net: phy: Introduce ethernet link topology representation")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 48939523843e4813e78920f54937944a8787134b upstream.
TJA1120B/TJA1121B can achieve a stable operation of SGMII after
a startup event by putting the SGMII PCS into power down mode and
restart afterwards.
It is necessary to put the SGMII PCS into power down mode and back up.
Cc: stable@vger.kernel.org
Fixes: f1fe5dff2b8a ("net: phy: nxp-c45-tja11xx: add TJA1120 support")
Signed-off-by: Andrei Botila <andrei.botila@oss.nxp.com>
Link: https://patch.msgid.link/20250304160619.181046-3-andrei.botila@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a07364b394697d2e0baffeb517f41385259aa484 upstream.
The most recent sillicon versions of TJA1120 and TJA1121 can achieve
full silicon performance by putting the PHY in managed mode.
It is necessary to apply these PHY writes before link gets established.
Application of this fix is required after restart of device and wakeup
from sleep.
Cc: stable@vger.kernel.org
Fixes: f1fe5dff2b8a ("net: phy: nxp-c45-tja11xx: add TJA1120 support")
Signed-off-by: Andrei Botila <andrei.botila@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250304160619.181046-2-andrei.botila@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b7a2c1fe6b55364e61b4b54b991eb43a47bb1104 ]
Introduce support for standardized PHY statistics reporting in ethtool
by extending the PHYLIB framework. Add the functions
phy_ethtool_get_phy_stats() and phy_ethtool_get_link_ext_stats() to
provide a consistent interface for retrieving PHY-level and
link-specific statistics. These functions are used within the ethtool
implementation to avoid direct access to the phy_device structure
outside of the PHYLIB framework.
A new structure, ethtool_phy_stats, is introduced to standardize PHY
statistics such as packet counts, byte counts, and error counters.
Drivers are updated to include callbacks for retrieving PHY and
link-specific statistics, ensuring values are explicitly set only for
supported fields, initialized with ETHTOOL_STAT_NOT_SET to avoid
ambiguity.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 637399bf7e77 ("net: ethtool: netlink: Allow NULL nlattrs when getting a phy_device")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 992ee3ed6e9fdd0be83a7daa5ff738e3cf86047f upstream.
While setting the DAC value, the wrong boolean value is evaluated to set
the DSP bias current. So let's correct the conditional statement and use
the right boolean value read from the DTS set in the priv.
Cc: stable@vger.kernel.org
Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250219130923.7216-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd1bbab717608757cccbbe08b0d46e6c3ed0ced5 upstream.
In application note (AN13663) for TJA1120, on page 30, there's a figure
with average PHY startup timing values following software reset.
The time it takes for SMI to become operational after software reset
ranges roughly from 500 us to 1500 us.
This commit adds 2000 us delay after MDIO write which triggers software
reset. Without this delay, soft_reset function returns an error and
prevents successful PHY init.
Cc: stable@vger.kernel.org
Fixes: b050f2f15e04 ("phy: nxp-c45: add driver for tja1103")
Signed-off-by: Milos Reljin <milos_reljin@outlook.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/AM8P250MB0124D258E5A71041AF2CC322E1E32@AM8P250MB0124.EURP250.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a197004cf3c2e6c8cc0695c787a97e62e3229754 ]
When using temperature measurement on Marvell 88Q2XXX devices and the
reset-gpios property is set in DT, the device does a hardware reset when
interface is brought down and up again. That means that the content of
the register MDIO_MMD_PCS_MV_TEMP_SENSOR2 is reset to default and that
leads to permanent deactivation of the temperature measurement, because
activation is done in mv88q2xxx_probe. To fix this move activation of
temperature measurement to mv88q222x_config_init.
Fixes: a557a92e6881 ("net: phy: marvell-88q2xxx: add support for temperature sensor")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250118-marvell-88q2xxx-fix-hwmon-v2-1-402e62ba2dcb@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d3eb58549842c60ed46f37da7f4da969e3d6ecd3 ]
Clear NBase-T link partner advertisement before calling
rtlgen_read_status() to avoid phy_resolve_aneg_linkmode() wrongly
setting speed and duplex.
This fixes bogus 2.5G/5G/10G link partner advertisement and thus
speed and duplex being set by phy_resolve_aneg_linkmode() due to stale
NBase-T lpa.
Fixes: 68d5cd09e891 ("net: phy: realtek: change order of calls in C22 read_status()")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea8318cb33e593bbfc59d637eae45a69732c5387 ]
rtlgen_decode_physr() which sets master_slave_state isn't called in case
the link is down and other than rtlgen_read_status(),
rtl822x_c45_read_status() doesn't implicitely clear master_slave_state.
Avoid stale master_slave_state by always setting it to
MASTER_SLAVE_STATE_UNKNOWN in rtl822x_c45_read_status() in case the link
is down.
Fixes: 081c9c0265c9 ("net: phy: realtek: read duplex and gbit master from PHYSR register")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34d5a86ff7bbe225fba3ad91f9b4dc85fb408e18 ]
Only read 1000Base-T link partner advertisement if autonegotiation has
completed and otherwise 1000Base-T link partner advertisement bits.
This fixes bogus 1000Base-T link partner advertisement after link goes
down (eg. by disconnecting the wire).
Fixes: 5cb409b3960e ("net: phy: realtek: clear 1000Base-T link partner advertisement")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
On the i.MX6ULL-14x14-EVK board, enet1_ref and enet2_ref are used as the
clock sources for two external KSZ PHYs. However, after closing the two
FEC ports, the clk_enable_count of the enet1_ref and enet2_ref clocks is
not 0. The root cause is that since the commit 985329462723 ("net: phy:
micrel: use devm_clk_get_optional_enabled for the rmii-ref clock"), the
external clock of KSZ PHY has been enabled when the PHY driver probes,
and it can only be disabled when the PHY driver is removed. This causes
the clock to continue working when the system is suspended or the network
port is down.
Although Heiko explained in the commit message that the patch was because
some clock suppliers need to enable the clock to get the valid clock rate
, it seems that the simple fix is to disable the clock after getting the
clock rate to solve the current problem. This is indeed true, but we need
to admit that Heiko's patch has been applied for more than a year, and we
cannot guarantee whether there are platforms that only enable rmii-ref in
the KSZ PHY driver during this period. If this is the case, disabling
rmii-ref will cause RMII on these platforms to not work.
Secondly, commit 99ac4cbcc2a5 ("net: phy: micrel: allow usage of generic
ethernet-phy clock") just simply enables the generic clock permanently,
which seems like the generic clock may only be enabled in the PHY driver.
If we simply disable the generic clock, RMII may not work. If we keep it
as it is, the platform using the generic clock will have the same problem
as the i.MX6ULL platform.
To solve this problem, the clock is enabled when phy_driver::resume() is
called, and the clock is disabled when phy_driver::suspend() is called.
Since phy_driver::resume() and phy_driver::suspend() are not called in
pairs, an additional clk_enable flag is added. When phy_driver::suspend()
is called, the clock is disabled only if clk_enable is true. Conversely,
when phy_driver::resume() is called, the clock is enabled if clk_enable
is false.
The changes that introduced the problem were only a few lines, while the
current fix is about a hundred lines, which seems out of proportion, but
it is necessary because kszphy_probe() is used by multiple KSZ PHYs and
we need to fix all of them.
Fixes: 985329462723 ("net: phy: micrel: use devm_clk_get_optional_enabled for the rmii-ref clock")
Fixes: 99ac4cbcc2a5 ("net: phy: micrel: allow usage of generic ethernet-phy clock")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241217063500.1424011-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gcc runs into undefined behavior at the end of the three led_polarity_set()
callback functions if it were called with a zero 'modes' argument and it
just ends the function there without returning from it.
This gets flagged by 'objtool' as a function that continues on
to the next one:
drivers/net/phy/aquantia/aquantia_leds.o: warning: objtool: aqr_phy_led_polarity_set+0xf: can't find jump dest instruction at .text+0x5d9
drivers/net/phy/intel-xway.o: warning: objtool: xway_gphy_led_polarity_set() falls through to next function xway_gphy_config_init()
drivers/net/phy/mxl-gpy.o: warning: objtool: gpy_led_polarity_set() falls through to next function gpy_led_hw_control_get()
There is no point to micro-optimize the behavior here to save a single-digit
number of bytes in the kernel, so just change this to a "return -EINVAL"
as we do when any unexpected bits are set.
Fixes: 1758af47b98c ("net: phy: intel-xway: add support for PHY LEDs")
Fixes: 9d55e68b19f2 ("net: phy: aquantia: correctly describe LED polarity override")
Fixes: eb89c79c1b8f ("net: phy: mxl-gpy: correctly describe LED polarity")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241217081056.238792-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LAN7800/7850
Fix outdated MII_LPA data in the LAN88xx PHY, which is used in LAN7800
and LAN7850 USB Ethernet controllers. Due to a hardware limitation, the
PHY cannot reliably update link status after parallel detection when the
link partner does not support auto-negotiation. To mitigate this, add a
PHY reset in `lan88xx_link_change_notify()` when `phydev->state` is
`PHY_NOLINK`, ensuring the PHY starts in a clean state and reports
accurate fixed link parallel detection results.
Fixes: 792aec47d59d9 ("add microchip LAN88xx phy driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241125084050.414352-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When phy_ethtool_set_eee_noneg() detects a change in the LPI
parameters, it attempts to update phylib state and trigger the link
to cycle so the MAC sees the updated parameters.
However, in doing so, it sets phydev->enable_tx_lpi depending on
whether the EEE configuration allows the MAC to generate LPI without
taking into account the result of negotiation.
This can be demonstrated with a 1000base-T FD interface by:
# ethtool --set-eee eno0 advertise 8 # cause EEE to be not negotiated
# ethtool --set-eee eno0 tx-lpi off
# ethtool --set-eee eno0 tx-lpi on
This results in being true, despite EEE not having been negotiated and:
# ethtool --show-eee eno0
EEE status: enabled - inactive
Tx LPI: 250 (us)
Supported EEE link modes: 100baseT/Full
1000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
Fix this by keeping track of whether EEE was negotiated via a new
eee_active member in struct phy_device, and include this state in
the decision whether phydev->enable_tx_lpi should be set.
Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tErSe-005RhB-2R@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phydev->eee_cfg.eee_enabled
This is a follow-up to 41ffcd95015f ("net: phy: fix phylib's dual
eee_enabled") and resolves an issue with genphy_c45_an_config_eee_aneg()
(called from genphy_c45_ethtool_set_eee) not seeing the new value of
phydev->eee_cfg.eee_enabled.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.13 net-next PR.
Conflicts:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
721aa69e708b net: phy: convert eee_broken_modes to a linkmode bitmap
https://lore.kernel.org/all/20241118135512.1039208b@canb.auug.org.au/
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
2160428bcb20 net: txgbe: fix null pointer to pcs
2160428bcb20 net: txgbe: remove GPIO interrupt controller
Adjacent commits:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
516a5f11eb97 net: phy: respect cached advertising when re-enabling EEE
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Adds support for clause-45 PHY loopback for the Microchip LAN887x driver.
Signed-off-by: Tarun Alle <Tarun.Alle@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241114101951.382996-1-Tarun.Alle@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylib has two eee_enabled members. Some parts of the code are using
phydev->eee_enabled, other parts are using phydev->eee_cfg.eee_enabled.
This leads to incorrect behaviour as their state goes out of sync.
ethtool --show-eee shows incorrect information, and --set-eee sometimes
doesn't take effect.
Fix this by only having one eee_enabled member - that in eee_cfg.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tBXAF-00341F-EQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DP83869 PHY transceiver supports converting from RGMII to 1000base-x.
In this operation mode, autonegotiation can be performed, as described in
IEEE802.3.
The DP83869 has a set of fiber-specific registers located at offset 0xc00.
When the transceiver is configured in RGMII-to-1000base-x mode, these
registers are mapped onto offset 0, which should make reading the
autonegotiation status transparent.
However, the fiber registers at offset 0xc04 and 0xc05 follow the bit
layout specified in Clause 37, and genphy_read_status() assumes a Clause 22
layout. Thus, genphy_read_status() doesn't properly read the capabilities
advertised by the link partner, resulting in incorrect link parameters.
Similarly, genphy_config_aneg() doesn't properly write advertised
capabilities.
Fix the 1000base-x autonegotiation procedure by replacing
genphy_read_status() and genphy_config_aneg() with their Clause 37
equivalents.
Fixes: a29de52ba2a1 ("net: dp83869: Add ability to advertise Fiber connection")
Cc: stable@vger.kernel.org
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://patch.msgid.link/20241112-dp83869-1000base-x-v3-1-36005f4ab0d9@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
eee_broken_modes has a eee_cap1 register layout currently. This doen't
allow to flag e.g. 2.5Gbps or 5Gbps BaseT EEE as broken. To overcome
this limitation switch eee_broken_modes to a linkmode bitmap.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dfe0c9ff-84b0-4328-86d7-e917ebc084a1@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc8).
Conflicts:
tools/testing/selftests/net/.gitignore
252e01e68241 ("selftests: net: add netlink-dumps to .gitignore")
be43a6b23829 ("selftests: ncdevmem: Move ncdevmem under drivers/net/hw")
https://lore.kernel.org/all/20241113122359.1b95180a@canb.auug.org.au/
drivers/net/phy/phylink.c
671154f174e0 ("net: phylink: ensure PHY momentary link-fails are handled")
7530ea26c810 ("net: phylink: remove "using_mac_select_pcs"")
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/dwmac-intel-plat.c
5b366eae7193 ("stmmac: dwmac-intel-plat: fix call balance of tx_clk handling routines")
e96321fad3ad ("net: ethernet: Switch back to struct platform_driver::remove()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Normally, phylib won't notify changes in quick succession. However, as
a result of commit 3e43b903da04 ("net: phy: Immediately call
adjust_link if only tx_lpi_enabled changes") this is no longer true -
it is now possible that phy_link_down() and phy_link_up() will both
complete before phylink's resolver has run, which means it'll miss that
pl->phy_state.link momentarily became false.
Rename "mac_link_dropped" to be more generic "link_failed" since it will
cover more than the MAC/PCS end of the link failing, and arrange to set
this in phylink_phy_change() if we notice that the PHY reports that the
link is down.
This will ensure that we capture an EEE reconfiguration event.
Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/E1tAtcW-002RBS-LB@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_ethtool_get_eee
genphy_c45_eee_is_active() populates both bitmaps only if it returns
successfully. So we can avoid the overhead of the temporary bitmaps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/b0832102-28ab-4223-b879-91fb1fc11278@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds MT7530 & MT7531's PHY ID macros in mtk-ge.c so that
it follows the same rule of mtk-ge-soc.c.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch integrates read/write page helper functions as MTK phy lib.
They are basically the same in mtk-ge.c & mtk-ge-soc.c.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mtk_phy_led_hw_ctrl_set()
This patch removes parens around TRIGGER_NETDEV_RX/TRIGGER_NETDEV_TX in
mtk_phy_led_hw_ctrl_set(), which improves readability.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch creates mtk-phy-lib.c & mtk-phy.h and integrates mtk-ge-soc.c's
LED helper functions so that we can use those helper functions in other
MTK's ethernet phy driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-organize MediaTek ethernet phy driver files and get ready to integrate
some common functions and add new 2.5G phy driver.
mtk-ge.c: MT7530 Gphy on MT7621 & MT7531 Gphy
mtk-ge-soc.c: Built-in Gphy on MT7981 & Built-in switch Gphy on MT7988
mtk-2p5ge.c: Planned for built-in 2.5G phy on MT7988
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have reduced the indentation level, clean up the code
formatting.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQz-002Ff5-EA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, so let's just convert everything to if()s. As a result of
the two preceding commits, there is now only one case in the switch()
statement. Remove the switch statement and reduce the code indentation.
Code reformatting will be in the following commit.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQu-002Fez-AA@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, and results in excessive indentation that spoils code
readability. Continue cleaning this up by converting the MLO_AN_PHY
case to use an if() statmeent.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQp-002Fet-5W@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The switch() statement doesn't sit very well with the preceeding if()
statements, and results in excessive indentation that spoils code
readability. Begin cleaning this up by converting the MLO_AN_FIXED case
to an if() statement.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQk-002Fen-1A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the handling of manual flow control configuration to a common
location during resolve. We currently evaluate this for all but
fixed links.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t9RQe-002Feh-T1@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for configuring MDI-X state of PHY.
Add reporting of resolved MDI-X state in status information.
Tested on AQR113C.
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Link: https://patch.msgid.link/20241106222057.3965379-1-paul.davey@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bcm_config_lre_aneg() doesn't use genphy_config_eee_advert() any longer.
As this was the only user, we can remove genphy_config_eee_advert() now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/37da7f3e-b883-4c07-9881-b8c0516822b7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bcm_config_lre_aneg() is the only user of genphy_config_eee_advert(),
therefore use genphy_c45_an_config_eee_aneg() instead. The resulting
functionality is equivalent, and bcm_config_lre_aneg() follows the
structure of __genphy_config_aneg().
In a follow-up step genphy_config_eee_advert() can be removed.
Note: We preserve the current behavior to ignore errors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/6e5cd4ab-28bb-4d82-b449-fec85f3d1e8a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We'll use this function in bcm_config_lre_aneg(), therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/02bd7c39-7413-4433-bafc-a276089bd292@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
genphy_c45_write_eee_adv() isn't used outside phy-c45.c,
so make it static.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/d23bd784-44e6-4a15-af3a-b37379156521@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc7).
Conflicts:
drivers/net/ethernet/freescale/enetc/enetc_pf.c
e15c5506dd39 ("net: enetc: allocate vf_state during PF probes")
3774409fd4c6 ("net: enetc: build enetc_pf_common.c as a separate module")
https://lore.kernel.org/20241105114100.118bd35e@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/ti/am65-cpsw-nuss.c
de794169cf17 ("net: ethernet: ti: am65-cpsw: Fix multi queue Rx on J7")
4a7b2ba94a59 ("net: ethernet: ti: am65-cpsw: Use tstats instead of open coded version")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The latter is the preferred way to copy ethtool strings.
Avoids manually incrementing the pointer. Cleans up the code quite well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20241104205317.306140-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we remove modes from EEE advertisement and disable / re-enable EEE,
then advertisement is set to all supported modes. I don't think this is
what the user expects. So respect the cached advertisement and just fall
back to all supported modes if cached advertisement is empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c75f7f8b-5571-429f-abd3-ce682d178a4b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad9378c ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241029234641.11448-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Like the DP83826, the DP83825 can also be configured as an RMII master or
slave via a control register. The existing function responsible for this
configuration is renamed to a general dp8382x function. The DP83825 only
supports RMII so nothing more needs to be configured.
With this change, the dp83822_driver list is reorganized according to the
device name.
Signed-off-by: Erik Schumacher <erik.schumacher@iris-sensing.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/aa62d081804f44b5af0e8de2372ae6bfe1affd34.camel@iris-sensing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate that the returned interface from sfp_select_interface() is
supportable by the MAC/PCS. If it isn't, print an error and return
the NA interface type. This is a preparatory step to reorganising
how a PHY on a SFP module is handled.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcV-000c8B-Vz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever we call sfp_select_interface(), we check the returned value
and print an error. There are two cases where this happens with the
same message. Provide a common function to do this.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcQ-000c85-S4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Report MDI-X resolved state after link up.
Tested on Linkstreet 88E6193X internal PHYs.
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241017015026.255224-1-paul.davey@alliedtelesis.co.nz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
