summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/mediatek/mt76/mt7996/mt7996.h
AgeCommit message (Collapse)AuthorFilesLines
2024-05-02wifi: mt76: connac: enable critical packet mode support for mt7992Howard Hsu1-0/+1
For mt7992 chipsets, critical packet mode should be properly configured to let the HW SDO module correctly fill the AC queue in TX descriptors of some higher priority packets such as ARP and ICMP. Without this patch, HW queues may hang when running MU traffic. Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-02wifi: mt76: connac: use peer address for station BMC entryShayne Chen1-1/+1
Set peer address and aid for the BMC wtbl of station interface. For some functions such as parsing MU_EDCA parameters from beacon, firmware will need the peer address to do correct parsing. Without this patch, MU uplink traffic would get suffered. Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-02wifi: mt76: mt7996: fix size of txpower MCU commandChad Monroe1-0/+1
Fixes issues with scanning and low power output at some rates. Fixes: f75e4779d215 ("wifi: mt76: mt7996: add txpower setting support") Signed-off-by: Chad Monroe <chad@monroe.io> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-02-22wifi: mt76: mt7996: add locking for accessing mapped registersShayne Chen1-2/+1
A race condition was observed when accessing mapped registers, so add locking to protect against concurrent access. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-02-22wifi: mt76: mt7996: fix TWT issuesPeter Chiu1-1/+2
This patch fixes the following TWT issues: - Change table_mask to u16 to support up to 16 TWT stations - Reject TWT flows for duplicated establishment - Fix possible unaligned pointer - Remove unsupported TWT_CONTROL_WAKE_DUR_UNIT flag - The minimum TWT duration supported by mt7996 chipsets is 64. Reply with TWT_SETUP_CMD_DICTATE if the min_twt_dur is smaller than 64 Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices") Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: adjust interface num and wtbl size for mt7992StanleyYP Wang1-3/+5
MT7992 chipsets support up to 32 interfaces (with maximum 19 per-band) and 512 station entries. This is a preliminary patch for mt7992 chipsets support. Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: support mt7992 eeprom loadingStanleyYP Wang1-0/+1
Add the default eeprom and 0x7992 check to mt7996_check_eeprom(). This is a preliminary patch for mt7992 chipsets support. Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add DMA support for mt7992Benjamin Lin1-2/+5
Add DMA TX/RX queues and RRO init flow for mt7992 chipsets. This is a preliminary patch for mt7992 chipsets support. Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Co-developed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: connac: add firmware support for mt7992StanleyYP Wang1-0/+5
Support firmware download and enable related AFE PLL for mt7992 chipsets. This is a preliminary patch for mt7992 chipsets support. Co-developed-by: Benjamin Lin <benjamin-jw.lin@mediatek.com> Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com> Co-developed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: introduce mt7996_band_valid()Shayne Chen1-3/+13
Replace dbdc_support and tbtc_support with mt7996_band_valid() to support mt7996 variants with band0/band2 dual-band support. This changes reduces ambiguity when checking supported bands on different variants or new chipsets, as well as during the init configurations on DMA TX/RX queues or irq masks. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: connac: add beacon protection support for mt7996Allen Ye1-1/+2
Implement beacon protection feature for mt7996 chipsets, and also do some cleanup on the set key routine. Co-developed-by: Rudra Shahi <rudra.shahi@mediatek.com> Signed-off-by: Rudra Shahi <rudra.shahi@mediatek.com> Signed-off-by: Allen Ye <allen.ye@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add txpower setting supportShayne Chen1-0/+3
Add support for setting txpower from upper layer and configuring per-rate txpower limit table. Co-developed-by: Allen Ye <allen.ye@mediatek.com> Signed-off-by: Allen Ye <allen.ye@mediatek.com> Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: change txpower init to per-phyShayne Chen1-2/+1
Use per-phy structure for maximum txpower value initializing, since each phy may have a different chainmask, which can impact the calculation of power gain. Co-developed-by: Allen Ye <allen.ye@mediatek.com> Signed-off-by: Allen Ye <allen.ye@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: handle IEEE80211_RC_SMPS_CHANGEDPeter Chiu1-0/+2
Make mt7996_mcu_set_fixed_field() non-static in order to handle IEEE80211_RC_SMPS_CHANGED in mt7996_mac_sta_rc_work(). Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: connac: add beacon duplicate TX mode support for mt7996StanleyYP Wang1-3/+5
For connac3 chipsets, setting of spe_idx is moved from TX descriptor to the fixed rate table. This patch implements the setting to support duplicate TX mode for beacon. Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: connac: add thermal protection support for mt7996Howard Hsu1-0/+15
Implement thermal protection commands and support Linux cooling device control for mt7996 chipsets. Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add support for variants with auxiliary RX pathShayne Chen1-0/+14
Add support to correctly configure the rx chainmask of variants that have additional auxiliary RX path. e.g., 4T5R. The auxiliary RX path is transparent to driver, but driver needs to correctly configure it in the set channel fw command. Co-developed-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add wed rro delete session garbage collectorLorenzo Bianconi1-0/+10
Introduce the capability to clear WED rro session configured in the hw according to the event reported by the MCU firmware Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add wed rx supportBo Jiao1-0/+55
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996 to offload traffic received from the WLAN nic and transmitted on the LAN one Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: use u16 for val field in mt7996_mcu_set_rro signatureLorenzo Bianconi1-1/+1
This is a preliminary patch to introduce WED rx support for mt7996 driver. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-12-07wifi: mt76: mt7996: add wed tx supportSujuan Chen1-1/+11
Similar to MT7915, enable Wireless Ethernet Ditpatcher for MT7996 to offload traffic received from the LAN nic and transmitted on the WLAN one Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-30wifi: mt76: mt7996: remove periodic MPDU TXS requestBenjamin Lin1-1/+0
Remove periodic MPDU TXS request. Get TID and FrameType from SKB instead of TXWI, which is empty for Data Frame after MPDU TXS request is removed, hence prohibiting the establishment of TX BA session. Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com> Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com> Signed-off-by: Money Wang <Money.Wang@mediatek.com> Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-09-30wifi: mt76: mt7996: Add mcu commands for getting sta tx statisticYi-Chia Hsieh1-0/+1
Per peer Tx/Rx statistic can only be obtained by querying WM when WED is on. This patch switches to periodic event reporting in the case of WED being enabled. Signed-off-by: Yi-Chia Hsieh <yi-chia.hsieh@mediatek.com> Signed-off-by: Money Wang <Money.Wang@mediatek.com> Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-26wifi: mt76: mt76_connac3: move lmac queue enumeration in mt76_connac3_mac.hLorenzo Bianconi1-14/+0
This is a preliminary patch to introduce mt7925 chip support Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: move rate info in mt76_vifLorenzo Bianconi1-4/+0
This is a preliminary patch to introduce mt76_connac3 mac library used by WiFi7 chipsets (e.g. mt7996). Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: move ampdu_state in mt76_wcidLorenzo Bianconi1-1/+0
ampdu_state field is used by most of the drivers, so move it in mt76_wcid structure. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: rely on shared poll_list fieldLorenzo Bianconi1-1/+0
Rely on poll_list field in mt76_wcid structure and get rid of private copy. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: rely on shared sta_poll_list and sta_poll_lockLorenzo Bianconi1-2/+0
Rely on sta_poll_list and sta_poll_lock fields in mt76_dev structure and get rid of private copies. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: increase tx token sizeHoward Hsu1-1/+1
Align tx token size to proprietary driver, which can improve peak throughput under MU performance tests. Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: fix WA event ring sizeStanleyYP Wang1-0/+1
Fix rx ring size of WA event to get rid of event loss and queue overflow problems. Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices") Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: connac: add support to set ifs time by mcu commandPeter Chiu1-1/+2
There's a race between driver and fw on some tx/rx control registers when setting ifs, which will cause accidental hw queue pause problems. Avoid this by setting ifs time with bss_info mcu command. Reviewed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: connac: add support for dsp firmware downloadPeter Chiu1-0/+7
Add FW_START_WORKING_PDA_DSP for the indication of starting DSP firmware download, which is for phy-related control. The firmware is transparent to the driver, but it's necessary for the firmware download process. Reviewed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25mt76: mt7996: rely on mt76_sta_stats in mt76_wcidLorenzo Bianconi1-2/+0
mt76 now accounts station stats in mt76_sta_stats available in mt76_wcid struct. Get rid of mt7996 private copy. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: disable WFDMA Tx/Rx during SER recoveryBo Jiao1-0/+1
Stop WFDMA transaction to avoid potential unexpected issue while doing system recovery. Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-07-25wifi: mt76: mt7996: rely on mib_stats shared definitionLorenzo Bianconi1-55/+1
Get rid of private copy of mib_stats structure. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-19wifi: mt76: mt7996: enable configured beacon tx rateRyder Lee1-0/+2
The user is allowed to change beacon tx rate (HT/VHT/HE) from hostapd. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-19wifi: mt76: mt7996: enable BSS_CHANGED_MCAST_RATE supportRyder Lee1-0/+1
Similar to BSS_CHANGED_BASIC_RATES, this enables mcast rate configuration through fixed rate tables. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Change-Id: Ifc305e8c7de9a7df4ad5f856e2097d721a886aaa Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-19wifi: mt76: mt7996: enable BSS_CHANGED_BASIC_RATES supportRyder Lee1-0/+7
The connac3 removes fixed rate fields to reduce txd size and introduces global rate tables (64 entries) for rate setting. Driver needs to fill the corresponding idx in MT_TXD6_TX_RATE while tx, and push mt76_rate into predifined table at bootup stage so that mvif->basic_rates_idx can immediately switch out once setting changes. spe_idx is also needed for fixed rate frames, and will be updated by future patches. Note that all table entries are shared across driver and firmware (i.e.TxBF), hence adding MT7996_BASIC_RATES_TBL to reflect mapping status. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: enable coredump supportRyder Lee1-0/+22
Host triggered and catastrophic event triggered firmware core dumping for basic firmware issues triage, including state reporting, function calltrace and MCU memory dump. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: add full system reset knobs into debugfsRyder Lee1-0/+1
Add testing points into debugfs to trigger firmware assert and enable full system recovery. Also rename knob "fw_ser" to a clear-cut name "sys_recovery". Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: enable full system reset supportBo Jiao1-1/+16
Add mt7996_reset() and refactor mt7996_mac_reset_work() to support full system recovery. Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: get rid of unused sta_ps callbacksLorenzo Bianconi1-1/+0
sta_ps callback is just an empty stub for most of the drivers, so get rid of them. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: move irq_tasklet in mt76_dev structLorenzo Bianconi1-2/+1
irq_tasklet struct is used by most of the drivers (e.g. mt7915, mt7921, mt7615, mt7663 and mt7996) so move it in common code. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: remove mt7996_mcu_set_pm()Peter Chiu1-1/+0
Currently using BSS_INFO_PS command will sometimes cause packet drop in hw rx queue. Temporarily remove this function until finding the cause. Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: let non-bufferable MMPDUs use correct hw queueShayne Chen1-2/+3
Pass qid into mt7996_mac_write_txwi() to let the tx descriptor of non-bufferable MMPDUs be filled with correct hw queue index. Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices") Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-04-17wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps()Ryder Lee1-16/+0
Those capabilities have been added into ieee80211_bss_conf. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-03wifi: mt76: mt7996: add EHT beamforming supportMeiChia Chiu1-0/+2
Add mt7996_mcu_sta_bfer_eht() and related capability checks. Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-03wifi: mt76: mt7996: add EHT capability initShayne Chen1-1/+1
Add EHT mac and phy capability init for mt7996 chipsets. Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Co-developed-by: MeiChia Chiu <meichia.chiu@mediatek.com> Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com> Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-03wifi: mt76: mt7996: add helpers for wtbl and interface limitShayne Chen1-4/+13
Add helpers to get the maximum wtbl size and interface num based on hw caps. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-03wifi: mt76: mt7996: add variants supportShayne Chen1-0/+4
There are variants of mt7996 which are different from eht supported and wtbl size limit. Get the hw caps with CHIP_CONFIG command. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2025-09-02 12:40:08 +0000