| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e08955 ("octeontx2-pf: Attach NIX and NPA block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
EEH: Beginning: 'slot_reset'
PCI 0011:01:00.0#10000: EEH: Invoking bnx2x->slot_reset()
bnx2x: [bnx2x_io_slot_reset:14228(eth1)]IO slot reset initializing...
bnx2x 0011:01:00.0: enabling device (0140 -> 0142)
bnx2x: [bnx2x_io_slot_reset:14244(eth1)]IO slot reset --> driver unload
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000025065fc
Oops: Kernel access of bad area, sig: 11 [#1]
.....
Call Trace:
[c000000003c67a20] [c00800000250658c] bnx2x_io_slot_reset+0x204/0x610 [bnx2x] (unreliable)
[c000000003c67af0] [c0000000000518a8] eeh_report_reset+0xb8/0xf0
[c000000003c67b60] [c000000000052130] eeh_pe_report+0x180/0x550
[c000000003c67c70] [c00000000005318c] eeh_handle_normal_event+0x84c/0xa60
[c000000003c67d50] [c000000000053a84] eeh_event_handler+0xf4/0x170
[c000000003c67da0] [c000000000194c58] kthread+0x1c8/0x1d0
[c000000003c67e10] [c00000000000cf64] ret_from_kernel_thread+0x5c/0x64
To solve this issue, we need to verify page pool allocations before
freeing.
Fixes: 4cace675d687 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Thinh Tran <thinhtr@linux.ibm.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20240315205535.1321-1-thinhtr@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull virtio updates from Michael Tsirkin:
- Per vq sizes in vdpa
- Info query for block devices support in vdpa
- DMA sync callbacks in vduse
- Fixes, cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (35 commits)
virtio_net: rename free_old_xmit_skbs to free_old_xmit
virtio_net: unify the code for recycling the xmit ptr
virtio-net: add cond_resched() to the command waiting loop
virtio-net: convert rx mode setting to use workqueue
virtio: packed: fix unmap leak for indirect desc table
vDPA: report virtio-blk flush info to user space
vDPA: report virtio-block read-only info to user space
vDPA: report virtio-block write zeroes configuration to user space
vDPA: report virtio-block discarding configuration to user space
vDPA: report virtio-block topology info to user space
vDPA: report virtio-block MQ info to user space
vDPA: report virtio-block max segments in a request to user space
vDPA: report virtio-block block-size to user space
vDPA: report virtio-block max segment size to user space
vDPA: report virtio-block capacity to user space
virtio: make virtio_bus const
vdpa: make vdpa_bus const
vDPA/ifcvf: implement vdpa_config_ops.get_vq_num_min
vDPA/ifcvf: get_max_vq_size to return max size
virtio_vdpa: create vqs with the actual size
...
|
|
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since Xilinx-based adapters now support up to eight CAN channels, the
TX interrupt mask array must have eight elements.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/2ab3c0585c3baba272ede0487182a423a420134b.camel@kvaser.com
Fixes: 9b221ba452aa ("can: kvaser_pciefd: Add support for Kvaser PCIe 8xCAN")
[mkl: replace Link by Fixes tag]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Reported-by: Lillian Berry <lillian@star-ark.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 3e2f544dd8a33 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core
and convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in this driver and leverage the network core
allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Syzkaller with KCSAN identified a data-race issue when accessing
keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE()
annotations to mark the data race as intentional.
BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll
write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0:
counter_validate drivers/net/wireguard/receive.c:321 [inline]
wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461
__napi_poll+0x60/0x3b0 net/core/dev.c:6536
napi_poll net/core/dev.c:6605 [inline]
net_rx_action+0x32b/0x750 net/core/dev.c:6738
__do_softirq+0xc4/0x279 kernel/softirq.c:553
do_softirq+0x5e/0x90 kernel/softirq.c:454
__local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499
process_one_work kernel/workqueue.c:2633 [inline]
...
read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1:
decrypt_packet drivers/net/wireguard/receive.c:252 [inline]
wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
...
Fixes: a9e90d9931f3 ("wireguard: noise: separate receive counter from send counter")
Reported-by: syzbot+d1de830e4ecdaac83d89@syzkaller.appspotmail.com
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since free_old_xmit_skbs not only deals with skb, but also xdp frame and
subsequent added xsk, so change the name of this function to
free_old_xmit.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240229072044.77388-19-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
There are two completely similar and independent implementations. This
is inconvenient for the subsequent addition of new types. So extract a
function from this piece of code and call this function uniformly to
recover old xmit ptr.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240229072044.77388-18-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Adding cond_resched() to the command waiting loop for a better
co-operation with the scheduler. This allows to give CPU a breath to
run other task(workqueue) instead of busy looping when preemption is
not allowed on a device whose CVQ might be slow.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230720083839.481487-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
|
|
This patch convert rx mode setting to be done in a workqueue, this is
a must for allow to sleep when waiting for the cvq command to
response since current code is executed under addr spin lock.
Note that we need to disable and flush the workqueue during freeze,
this means the rx mode setting is lost after resuming. This is not the
bug of this patch as we never try to restore rx mode setting during
resume.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230720083839.481487-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing updates from Steven Rostedt:
"Main user visible change:
- User events can now have "multi formats"
The current user events have a single format. If another event is
created with a different format, it will fail to be created. That
is, once an event name is used, it cannot be used again with a
different format. This can cause issues if a library is using an
event and updates its format. An application using the older format
will prevent an application using the new library from registering
its event.
A task could also DOS another application if it knows the event
names, and it creates events with different formats.
The multi-format event is in a different name space from the single
format. Both the event name and its format are the unique
identifier. This will allow two different applications to use the
same user event name but with different payloads.
- Added support to have ftrace_dump_on_oops dump out instances and
not just the main top level tracing buffer.
Other changes:
- Add eventfs_root_inode
Only the root inode has a dentry that is static (never goes away)
and stores it upon creation. There's no reason that the thousands
of other eventfs inodes should have a pointer that never gets set
in its descriptor. Create a eventfs_root_inode desciptor that has a
eventfs_inode descriptor and a dentry pointer, and only the root
inode will use this.
- Added WARN_ON()s in eventfs
There's some conditionals remaining in eventfs that should never be
hit, but instead of removing them, add WARN_ON() around them to
make sure that they are never hit.
- Have saved_cmdlines allocation also include the map_cmdline_to_pid
array
The saved_cmdlines structure allocates a large amount of data to
hold its mappings. Within it, it has three arrays. Two are already
apart of it: map_pid_to_cmdline[] and saved_cmdlines[]. More memory
can be saved by also including the map_cmdline_to_pid[] array as
well.
- Restructure __string() and __assign_str() macros used in
TRACE_EVENT()
Dynamic strings in TRACE_EVENT() are declared with:
__string(name, source)
And assigned with:
__assign_str(name, source)
In the tracepoint callback of the event, the __string() is used to
get the size needed to allocate on the ring buffer and
__assign_str() is used to copy the string into the ring buffer.
There's a helper structure that is created in the TRACE_EVENT()
macro logic that will hold the string length and its position in
the ring buffer which is created by __string().
There are several trace events that have a function to create the
string to save. This function is executed twice. Once for
__string() and again for __assign_str(). There's no reason for
this. The helper structure could also save the string it used in
__string() and simply copy that into __assign_str() (it also
already has its length).
By using the structure to store the source string for the
assignment, it means that the second argument to __assign_str() is
no longer needed.
It will be removed in the next merge window, but for now add a
warning if the source string given to __string() is different than
the source string given to __assign_str(), as the source to
__assign_str() isn't even used and will be going away.
- Added checks to make sure that the source of __string() is also the
source of __assign_str() so that it can be safely removed in the
next merge window.
Included fixes that the above check found.
- Other minor clean ups and fixes"
* tag 'trace-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (34 commits)
tracing: Add __string_src() helper to help compilers not to get confused
tracing: Use strcmp() in __assign_str() WARN_ON() check
tracepoints: Use WARN() and not WARN_ON() for warnings
tracing: Use div64_u64() instead of do_div()
tracing: Support to dump instance traces by ftrace_dump_on_oops
tracing: Remove second parameter to __assign_rel_str()
tracing: Add warning if string in __assign_str() does not match __string()
tracing: Add __string_len() example
tracing: Remove __assign_str_len()
ftrace: Fix most kernel-doc warnings
tracing: Decrement the snapshot if the snapshot trigger fails to register
tracing: Fix snapshot counter going between two tracers that use it
tracing: Use EVENT_NULL_STR macro instead of open coding "(null)"
tracing: Use ? : shortcut in trace macros
tracing: Do not calculate strlen() twice for __string() fields
tracing: Rework __assign_str() and __string() to not duplicate getting the string
cxl/trace: Properly initialize cxl_poison region name
net: hns3: tracing: fix hclgevf trace event strings
drm/i915: Add missing ; to __assign_str() macros in tracepoint code
NFSD: Fix nfsd_clid_class use of __string_len() macro
...
|
|
The __string() and __assign_str() helper macros of the TRACE_EVENT() macro
are going through some optimizations where only the source string of
__string() will be used and the __assign_str() source will be ignored and
later removed.
To make sure that there's no issues, a new check is added between the
__string() src argument and the __assign_str() src argument that does a
strcmp() to make sure they are the same string.
The hclgevf trace events have:
__assign_str(devname, &hdev->nic.kinfo.netdev->name);
Which triggers the warning:
hclgevf_trace.h:34:39: error: passing argument 1 of ‘strcmp’ from incompatible pointer type [-Werror=incompatible-pointer-types]
34 | __assign_str(devname, &hdev->nic.kinfo.netdev->name);
[..]
arch/x86/include/asm/string_64.h:75:24: note: expected ‘const char *’ but argument is of type ‘char (*)[16]’
75 | int strcmp(const char *cs, const char *ct);
| ~~~~~~~~~~~~^~
Because __assign_str() now has:
WARN_ON_ONCE(__builtin_constant_p(src) ? \
strcmp((src), __data_offsets.dst##_ptr_) : \
(src) != __data_offsets.dst##_ptr_); \
The problem is the '&' on hdev->nic.kinfo.netdev->name. That's because
that name is:
char name[IFNAMSIZ]
Where passing an address '&' of a char array is not compatible with strcmp().
The '&' is not necessary, remove it.
Link: https://lore.kernel.org/linux-trace-kernel/20240313093454.3909afe7@gandalf.local.home
Cc: netdev <netdev@vger.kernel.org>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: stable@vger.kernel.org
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Fixes: d8355240cf8fb ("net: hns3: add trace event support for PF/VF mailbox")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
ESW_P4_LED_0 ESW_P3_LED_0 Frequency
-----------------------------------------
0 0 Reserved
0 1 20MHz
1 0 40MHz
1 1 25MHz
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] [3] [5]
: : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
_____________________________
ESW_P3_LED_0 |__________________________
: : : :
: : [4]...:
: :
[2]................:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] [2-1] [3] [5]
: : : :
_____________________________ __________________
ESW_P4_LED_0 |_______|
___________________ _______
ESW_P3_LED_0 |_________| |__________________
: : : : :
: [2-2]...: [4]...:
[2]................:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
ESW_P3_LED_0 low period before reset deassertion:
5000 usec
- 5100 usec
TEST RESET HOLD
# (usec)
---------------------
1 5410
2 5440
3 4375
4 5490
5 5475
6 4335
7 4370
8 5435
9 4205
10 4335
11 3750
12 3170
13 4395
14 4375
15 3515
16 4335
17 4220
18 4175
19 4175
20 4350
Min 3170
Max 5490
Median 4342.500
Avg 4466.500
Revert commit 2920dd92b980 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d3256efd8e8b ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355f0 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/
Fixes: d3256efd8e8b ("veth: allow enabling NAPI even without XDP")
Fixes: fe9f801355f0 ("net: veth: clear GRO when clearing XDP even when down")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fsl_qmc_driver does not compile as module:
error: ‘qmc_hdlc_driver’ undeclared here (not in a function);
405 | MODULE_DEVICE_TABLE(of, qmc_hdlc_driver);
| ^~~~~~~~~~~~~~~
Fix the typo.
Fixes: b40f00ecd463 ("net: wan: Add support for QMC HDLC")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Closes: https://lore.kernel.org/linux-kernel/87ttl93f7i.fsf@mail.lhotse/
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add AT_HWCAP3 and AT_HWCAP4 aux vector entries for future use
by glibc
- Add support for recognising the Power11 architected and raw PVRs
- Add support for nr_cpus=n on the command line where the
boot CPU is >= n
- Add ppcxx_allmodconfig targets for all 32-bit sub-arches
- Other small features, cleanups and fixes
Thanks to Akanksha J N, Brian King, Christophe Leroy, Dawei Li, Geoff
Levand, Greg Kroah-Hartman, Jan-Benedict Glaw, Kajol Jain, Kunwu Chan,
Li zeming, Madhavan Srinivasan, Masahiro Yamada, Nathan Chancellor,
Nicholas Piggin, Peter Bergner, Qiheng Lin, Randy Dunlap, Ricardo B.
Marliere, Rob Herring, Sathvika Vasireddy, Shrikanth Hegde, Uwe
Kleine-König, Vaibhav Jain, and Wen Xiong.
* tag 'powerpc-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (71 commits)
powerpc/macio: Make remove callback of macio driver void returned
powerpc/83xx: Fix build failure with FPU=n
powerpc/64s: Fix get_hugepd_cache_index() build failure
powerpc/4xx: Fix warp_gpio_leds build failure
powerpc/amigaone: Make several functions static
powerpc/embedded6xx: Fix no previous prototype for avr_uart_send() etc.
macintosh/adb: make adb_dev_class constant
powerpc: xor_vmx: Add '-mhard-float' to CFLAGS
powerpc/fsl: Fix mfpmr() asm constraint error
powerpc: Remove cpu-as-y completely
powerpc/fsl: Modernise mt/mfpmr
powerpc/fsl: Fix mfpmr build errors with newer binutils
powerpc/64s: Use .machine power4 around dcbt
powerpc/64s: Move dcbt/dcbtst sequence into a macro
powerpc/mm: Code cleanup for __hash_page_thp
powerpc/hv-gpci: Fix the H_GET_PERF_COUNTER_INFO hcall return value checks
powerpc/irq: Allow softirq to hardirq stack transition
powerpc: Stop using of_root
powerpc/machdep: Define 'compatibles' property in ppc_md and use it
of: Reimplement of_machine_is_compatible() using of_machine_compatible_match()
...
|
|
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/b40da332dfe763932a82f9f62a4709457a15dd6c
Fixes: ba37b7caf1ed ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clearing bit MAC_MCR_FORCE_LINK which forces the link down too early
can result in MAC ending up in a broken/blocked state.
Fix this by handling this bit in the .mac_link_up and .mac_link_down
calls instead of in .mac_finish.
Fixes: b8fc9f30821e ("net: ethernet: mediatek: Add basic PHYLINK support")
Suggested-by: Mason-cw Chang <Mason-cw.Chang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- Kuan-Wei Chiu has developed the well-named series "lib min_heap: Min
heap optimizations".
- Kuan-Wei Chiu has also sped up the library sorting code in the series
"lib/sort: Optimize the number of swaps and comparisons".
- Alexey Gladkov has added the ability for code running within an IPC
namespace to alter its IPC and MQ limits. The series is "Allow to
change ipc/mq sysctls inside ipc namespace".
- Geert Uytterhoeven has contributed some dhrystone maintenance work in
the series "lib: dhry: miscellaneous cleanups".
- Ryusuke Konishi continues nilfs2 maintenance work in the series
"nilfs2: eliminate kmap and kmap_atomic calls"
"nilfs2: fix kernel bug at submit_bh_wbc()"
- Nathan Chancellor has updated our build tools requirements in the
series "Bump the minimum supported version of LLVM to 13.0.1".
- Muhammad Usama Anjum continues with the selftests maintenance work in
the series "selftests/mm: Improve run_vmtests.sh".
- Oleg Nesterov has done some maintenance work against the signal code
in the series "get_signal: minor cleanups and fix".
Plus the usual shower of singleton patches in various parts of the tree.
Please see the individual changelogs for details.
* tag 'mm-nonmm-stable-2024-03-14-09-36' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (77 commits)
nilfs2: prevent kernel bug at submit_bh_wbc()
nilfs2: fix failure to detect DAT corruption in btree and direct mappings
ocfs2: enable ocfs2_listxattr for special files
ocfs2: remove SLAB_MEM_SPREAD flag usage
assoc_array: fix the return value in assoc_array_insert_mid_shortcut()
buildid: use kmap_local_page()
watchdog/core: remove sysctl handlers from public header
nilfs2: use div64_ul() instead of do_div()
mul_u64_u64_div_u64: increase precision by conditionally swapping a and b
kexec: copy only happens before uchunk goes to zero
get_signal: don't initialize ksig->info if SIGNAL_GROUP_EXIT/group_exec_task
get_signal: hide_si_addr_tag_bits: fix the usage of uninitialized ksig
get_signal: don't abuse ksig->info.si_signo and ksig->sig
const_structs.checkpatch: add device_type
Normalise "name (ad@dr)" MODULE_AUTHORs to "name <ad@dr>"
dyndbg: replace kstrdup() + strchr() with kstrdup_and_replace()
list: leverage list_is_head() for list_entry_is_head()
nilfs2: MAINTAINERS: drop unreachable project mirror site
smp: make __smp_processor_id() 0-argument macro
fat: fix uninitialized field in nostale filehandles
...
|
|
txgbe register clk which name is i2c_designware.pci_dev_id(),
clk_name will be stored in clk_lookup_alloc. If PCIe bus number
is larger than 0x39, clk_name size will be larger than 20 bytes.
It exceeds clk_lookup_alloc MAX_DEV_ID limits. So the driver
shortened clk_name.
Fixes: b63f20485e43 ("net: txgbe: Register fixed rate clock")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20240313080634.459523-1-duanqiangwen@net-swift.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use rbi->len instead of rcd->len for non-dataring packet.
Found issue:
XDP_WARN: xdp_update_frame_from_buff(line:278): Driver BUG: missing reserved tailroom
WARNING: CPU: 0 PID: 0 at net/core/xdp.c:586 xdp_warn+0xf/0x20
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W O 6.5.1 #1
RIP: 0010:xdp_warn+0xf/0x20
...
? xdp_warn+0xf/0x20
xdp_do_redirect+0x15f/0x1c0
vmxnet3_run_xdp+0x17a/0x400 [vmxnet3]
vmxnet3_process_xdp+0xe4/0x760 [vmxnet3]
? vmxnet3_tq_tx_complete.isra.0+0x21e/0x2c0 [vmxnet3]
vmxnet3_rq_rx_complete+0x7ad/0x1120 [vmxnet3]
vmxnet3_poll_rx_only+0x2d/0xa0 [vmxnet3]
__napi_poll+0x20/0x180
net_rx_action+0x177/0x390
Reported-by: Martin Zaharinov <micron10@gmail.com>
Tested-by: Martin Zaharinov <micron10@gmail.com>
Link: https://lore.kernel.org/netdev/74BF3CC8-2A3A-44FF-98C2-1E20F110A92E@gmail.com/
Fixes: 54f00cce1178 ("vmxnet3: Add XDP support.")
Signed-off-by: William Tu <witu@nvidia.com>
Link: https://lore.kernel.org/r/20240309183147.28222-1-witu@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
WiFi 2x2 + BT combo cards can be two or three physical antenna. For two
antenna case, one antenna is shared by WiFi and BT, and different
configuration should be applied. Fix the typo.
This problem was found by Coccicheck, and actually that is a typo instead:
rtw8922a.c:2235:2-4: WARNING: possible condition with no effect (if == else)
Fixes: 652c9642eda6 ("wifi: rtw89: coex: add init_info H2C command format version 7")
Closes: https://lore.kernel.org/linux-wireless/20240308074539.04512f66@kernel.org/
Cc: Ching-Te Ku <ku920601@realtek.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240309001348.9906-1-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These mostly change the thermal core in a few ways allowing thermal
drivers to be simplified, in particular in their removal and failing
probe handling parts that are notoriously prone to errors, and
propagate the changes to several drivers.
Apart from that, support for a new platform is added (Intel Lunar
Lake-M), some bugs are fixed and some code is cleaned up, as usual.
Specifics:
- Store zone trips table and zone operations directly in struct
thermal_zone_device (Rafael Wysocki)
- Fix up flex array initialization during thermal zone device
registration (Nathan Chancellor)
- Rework writable trip points handling in the thermal core and
several drivers (Rafael Wysocki)
- Thermal core code cleanups (Dan Carpenter, Flavio Suligoi)
- Use thermal zone accessor functions in the int340x Intel thermal
driver (Rafael Wysocki)
- Add Lunar Lake-M PCI ID to the int340x Intel thermal driver
(Srinivas Pandruvada)
- Minor fixes for thermal governors (Rafael Wysocki, Di Shen)
- Trip point handling fixes for the iwlwifi wireless driver (Rafael
Wysocki)
- Code cleanups (Rafael J. Wysocki, AngeloGioacchino Del Regno)"
* tag 'thermal-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (29 commits)
thermal: core: remove unnecessary check in trip_point_hyst_store()
thermal: intel: int340x_thermal: Use thermal zone accessor functions
thermal: core: Remove excess empty line from a comment
thermal: int340x: processor_thermal: Add Lunar Lake-M PCI ID
thermal: core: Eliminate writable trip points masks
thermal: of: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: imx: Set THERMAL_TRIP_FLAG_RW_TEMP directly
wifi: iwlwifi: mvm: Set THERMAL_TRIP_FLAG_RW_TEMP directly
mlxsw: core_thermal: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: intel: Set THERMAL_TRIP_FLAG_RW_TEMP directly
thermal: core: Drop the .set_trip_hyst() thermal zone operation
thermal: core: Add flags to struct thermal_trip
thermal: core: Move initial num_trips assignment before memcpy()
thermal: Get rid of CONFIG_THERMAL_WRITABLE_TRIPS
thermal: intel: Adjust ops handling during thermal zone registration
thermal: ACPI: Constify acpi_thermal_zone_ops
thermal: core: Store zone ops in struct thermal_zone_device
thermal: intel: Discard trip tables after zone registration
thermal: ACPI: Discard trips table after zone registration
thermal: core: Store zone trips table in struct thermal_zone_device
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"From the functional perspective, the most significant change here is
the addition of support for Energy Models that can be updated
dynamically at run time.
There is also the addition of LZ4 compression support for hibernation,
the new preferred core support in amd-pstate, new platforms support in
the Intel RAPL driver, new model-specific EPP handling in intel_pstate
and more.
Apart from that, the cpufreq default transition delay is reduced from
10 ms to 2 ms (along with some related adjustments), the system
suspend statistics code undergoes a significant rework and there is a
usual bunch of fixes and code cleanups all over.
Specifics:
- Allow the Energy Model to be updated dynamically (Lukasz Luba)
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V)
- Fix and clean up system suspend statistics collection (Rafael
Wysocki)
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki)
- Fix PCI hibernation support description (Yiwei Lin)
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy)
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah)
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li)
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus)
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat)
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin)
- Enable preferred core support in the amd-pstate cpufreq driver
(Meng Li)
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li)
- Allow intel_pstate to assign model-specific values to strings used
in the EPP sysfs interface and make it do so on Meteor Lake
(Srinivas Pandruvada)
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby)
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar)
- Change default transition delay in cpufreq to 2ms (Qais Yousef)
- Remove references to 10ms minimum sampling rate from comments in
the cpufreq code (Pierre Gondois)
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef)
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar)
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova)
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan)
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois)
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle)
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng)
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang)
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui)
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano)
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li)
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda)
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil)
- Fix a couple of warnings in the OPP core code related to W=1 builds
(Viresh Kumar)
- Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh
Kumar)
- Extend dev_pm_opp_data with turbo support (Sibi Sankar)
- dt-bindings: drop maxItems from inner items (David Heidelberg)"
* tag 'pm-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (95 commits)
dt-bindings: opp: drop maxItems from inner items
OPP: debugfs: Fix warning around icc_get_name()
OPP: debugfs: Fix warning with W=1 builds
cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
OPP: Extend dev_pm_opp_data with turbo support
Fix cpupower-frequency-info.1 man page typo
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
PM: sleep: wakeirq: fix wake irq warning in system suspend
powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
PM: suspend: Set mem_sleep_current during kernel command line setup
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
Documentation: PM: Fix runtime_pm.rst markdown syntax
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release sees some exciting changes from David Lechner which
implements some optimisations that have been talked about for a long
time which allows client drivers to pre-prepare SPI messages for
repeated or low latency use. This lets us move work out of latency
sensitive paths and avoid repeating work for frequently performed
operations. As well as being useful in itself this will also be used
in future to allow controllers to directly trigger SPI operations (eg,
from interrupts).
Otherwise this release has mostly been focused on cleanups, plus a
couple of new devices:
- Support for pre-optimising messages
- A big set of updates from Uwe Kleine-König moving drivers to use
APIs with more modern terminology for controllers
- Major overhaul of the s3c64xx driver
- Support for Google GS101 and Samsung Exynos850"
* tag 'spi-v6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (122 commits)
spi: Introduce SPI_INVALID_CS and is_valid_cs()
spi: Fix types of the last chip select storage variables
spi: Consistently use BIT for cs_index_mask
spi: Exctract spi_dev_check_cs() helper
spi: Exctract spi_set_all_cs_unused() helper
spi: s3c64xx: switch exynos850 to new port config data
spi: s3c64xx: switch gs101 to new port config data
spi: s3c64xx: deprecate fifo_lvl_mask, rx |
