summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2024-02-16i40e: Remove VEB recursionIvan Vecera3-109/+76
The VEB (virtual embedded switch) as a switch element can be connected according datasheet though its uplink to: - Physical port - Port Virtualizer (not used directly by i40e driver but can be present in MFP mode where the physical port is shared between PFs) - No uplink (aka floating VEB) But VEB uplink cannot be connected to another VEB and any attempt to do so results in: "i40e 0000:02:00.0: couldn't add VEB, err -EIO aq_err I40E_AQ_RC_ENOENT" that indicates "the uplink SEID does not point to valid element". Remove this logic from the driver code this way: 1) For debugfs only allow to build floating VEB (uplink_seid == 0) or main VEB (uplink_seid == mac_seid) 2) Do not recurse in i40e_veb_link_event() as no VEB cannot have sub-VEBs 3) Ditto for i40e_veb_rebuild() + simplify the function as we know that the VEB for rebuild can be only the main LAN VEB or some of the floating VEBs 4) In i40e_rebuild() there is no need to check veb->uplink_seid as the possible ones are 0 and MAC SEID 5) In i40e_vsi_release() do not take into account VEBs whose uplink is another VEB as this is not possible 6) Remove veb_idx field from i40e_veb as a VEB cannot have sub-VEBs Tested using i40e debugfs interface: 1) Initial state [root@cnb-03 net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command" [root@cnb-03 net-next]# echo dump switch > $CMD [root@cnb-03 net-next]# dmesg -c [ 98.440641] i40e 0000:02:00.0: header: 3 reported 3 total [ 98.446053] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 98.452593] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 98.458856] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 2) Add floating VEB [root@cnb-03 net-next]# echo add relay > $CMD [root@cnb-03 net-next]# dmesg -c [ 122.745630] i40e 0000:02:00.0: added relay 162 [root@cnb-03 net-next]# echo dump switch > $CMD [root@cnb-03 net-next]# dmesg -c [ 136.650049] i40e 0000:02:00.0: header: 4 reported 4 total [ 136.655466] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 136.661994] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 136.668264] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 [ 136.674787] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 3) Add VMDQ2 VSI to this new VEB [root@cnb-03 net-next]# dmesg -c [ 168.351763] i40e 0000:02:00.0: added VSI 394 to relay 162 [ 168.374652] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None [root@cnb-03 net-next]# echo dump switch > $CMD [root@cnb-03 net-next]# dmesg -c [ 195.683204] i40e 0000:02:00.0: header: 5 reported 5 total [ 195.688611] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16 [ 195.695143] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 [ 195.701410] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 195.707935] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 195.714201] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 4) Try to delete the VEB [root@cnb-03 net-next]# echo del relay 162 > $CMD [root@cnb-03 net-next]# dmesg -c [ 239.260901] i40e 0000:02:00.0: deleting relay 162 [ 239.265621] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left 5) Do PF reset and check switch status after rebuild [root@cnb-03 net-next]# echo pfr > $CMD [root@cnb-03 net-next]# echo dump switch > $CMD [root@cnb-03 net-next]# dmesg -c ... [ 272.333655] i40e 0000:02:00.0: header: 5 reported 5 total [ 272.339066] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16 [ 272.345599] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 [ 272.351862] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 272.358387] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 272.364654] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 6) Delete VSI and delete VEB [ 297.199116] i40e 0000:02:00.0: deleting VSI 394 [ 299.807580] i40e 0000:02:00.0: deleting relay 162 [ 309.767905] i40e 0000:02:00.0: header: 3 reported 3 total [ 309.773318] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 309.779845] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 309.786111] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-16i40e: Fix broken support for floating VEBsIvan Vecera2-49/+67
Although the i40e supports so-called floating VEB (VEB without an uplink connection to external network), this support is broken. This functionality is currently unused (except debugfs) but it will be used by subsequent series for switchdev mode slow-path. Fix this by following: 1) Handle correctly floating VEB (VEB with uplink_seid == 0) in i40e_reconstitute_veb() and look for owner VSI and create it only for non-floating VEBs and also set bridge mode only for such VEBs as the floating ones are using always VEB mode. 2) Handle correctly floating VEB in i40e_veb_release() and disallow its release when there are some VSIs. This is different from regular VEB that have owner VSI that is connected to VEB's uplink after VEB deletion by FW. 3) Fix i40e_add_veb() to handle 'vsi' that is NULL for floating VEBs. For floating VEB use 0 for downlink SEID and 'true' for 'default_port' parameters as per datasheet. 4) Fix 'add relay' command in i40e_dbg_command_write() to allow to create floating VEB by 'add relay 0 0' or 'add relay' Tested using debugfs: 1) Initial state [root@host net-next]# echo dump switch > $CMD [root@host net-next]# dmesg -c [ 173.701286] i40e 0000:02:00.0: header: 3 reported 3 total [ 173.706701] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 173.713241] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 173.719507] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 2) Add floating VEB [root@host net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command" [root@host net-next]# echo add relay > $CMD [root@host net-next]# dmesg -c [ 245.551720] i40e 0000:02:00.0: added relay 162 [root@host net-next]# echo dump switch > $CMD [root@host net-next]# dmesg -c [ 276.984371] i40e 0000:02:00.0: header: 4 reported 4 total [ 276.989779] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 276.996302] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 277.002569] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 [ 277.009091] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 3) Add VMDQ2 VSI to this new VEB [root@host net-next]# echo add vsi 162 > $CMD [root@host net-next]# dmesg -c [ 332.314030] i40e 0000:02:00.0: added VSI 394 to relay 162 [ 332.337486] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None [root@host net-next]# echo dump switch > $CMD [root@host net-next]# dmesg -c [ 387.284490] i40e 0000:02:00.0: header: 5 reported 5 total [ 387.289904] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16 [ 387.296446] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 [ 387.302708] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 387.309234] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 387.315500] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 4) Try to delete the VEB [root@host net-next]# echo del relay 162 > $CMD [root@host net-next]# dmesg -c [ 428.749297] i40e 0000:02:00.0: deleting relay 162 [ 428.754011] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left 5) Do PF reset and check switch status after rebuild [root@host net-next]# echo pfr > $CMD [root@host net-next]# echo dump switch > $CMD [root@host net-next]# dmesg -c [ 738.056172] i40e 0000:02:00.0: header: 5 reported 5 total [ 738.061577] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16 [ 738.068104] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0 [ 738.074367] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 738.080892] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 738.087160] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 6) Delete VSI and delete VEB [root@host net-next]# echo del vsi 394 > $CMD [root@host net-next]# echo del relay 162 > $CMD [root@host net-next]# echo dump switch > $CMD [root@host net-next]# dmesg -c [ 1233.081126] i40e 0000:02:00.0: deleting VSI 394 [ 1239.345139] i40e 0000:02:00.0: deleting relay 162 [ 1244.886920] i40e 0000:02:00.0: header: 3 reported 3 total [ 1244.892328] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16 [ 1244.898853] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0 [ 1244.905119] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16 Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-16i40e: Add helpers to find VSI and VEB by SEID and use themIvan Vecera3-86/+68
Add two helpers i40e_(veb|vsi)_get_by_seid() to find corresponding VEB or VSI by their SEID value and use these helpers to replace existing open-coded loops. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-16i40e: Introduce and use macros for iterating VSIs and VEBsIvan Vecera4-245/+264
Introduce i40e_for_each_vsi() and i40e_for_each_veb() helper macros and use them to iterate relevant arrays. Replace pattern: for (i = 0; i < pf->num_alloc_vsi; i++) by: i40e_for_each_vsi(pf, i, vsi) and pattern: for (i = 0; i < I40E_MAX_VEB; i++) by i40e_for_each_veb(pf, i, veb) These macros also check if array item pf->vsi[i] or pf->veb[i] are not NULL and skip such items so we can remove redundant checks from loop bodies. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-16i40e: Use existing helper to find flow director VSIIvan Vecera1-7/+4
Use existing i40e_find_vsi_by_type() to find a VSI associated with flow director. Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-16net: phy: aquantia: add AQR113 PHY IDChristian Marangi1-0/+21
Add Aquantia AQR113 PHY ID. Aquantia AQR113 is just a chip size variant of the already supported AQR133C where the only difference is the PHY ID and the hw chip size. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ti: icssg-prueth: Remove duplicate cleanup calls in emac_ndo_stop()Diogo Ivo1-4/+0
Remove the duplicate calls to prueth_emac_stop() and prueth_cleanup_tx_chns() in emac_ndo_stop(). Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Reviewed-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: implement xdp frags supportShannon Nelson2-5/+98
Add support for using scatter-gather / frags in XDP in both Rx and Tx paths. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: add ndo_xdp_xmitShannon Nelson3-2/+66
When our ndo_xdp_xmit is called we mark the buffer with XDP_REDIRECT so we know to return it to the XDP stack for cleaning. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: Add XDP_REDIRECT supportShannon Nelson5-1/+32
The XDP_REDIRECT packets are given to the XDP stack and we drop the use of the related page: it will get freed by the driver that ends up doing the Tx. Because we have some hardware configurations with limited queue resources, we use the existing datapath Tx queues rather than creating and managing a separate set of xdp_tx queues. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: Add XDP_TX supportShannon Nelson5-3/+150
The XDP_TX packets get fed back into the Rx queue's partnered Tx queue as an xdp_frame. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: Add XDP packet headroomShannon Nelson1-23/+45
If an xdp program is loaded, add headroom at the beginning of the frame to allow for editing and insertions that an XDP program might need room for, and tailroom used later for XDP frame tracking. These are only needed in the first Rx buffer in a packet, not for any trailing frags. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: add initial framework for XDP supportShannon Nelson6-14/+269
Set up the basics for running Rx packets through XDP programs. Add new queue setup and teardown steps for adding/removing an XDP program, and add the call to run the XDP on a packet. The XDP frame size needs to be the MTU plus standard ethernet header, plus head room for XDP scribblings and tail room for a struct skb_shared_info. Also, at this point, we don't support XDP frags, only a single contiguous Rx buffer. This means that our page splitting is not very useful, so when XDP is in use we need to use the full Rx buffer size and not do sharing. Co-developed-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: use dma range APIsShannon Nelson1-7/+6
Convert Rx datapath handling to use the DMA range APIs in preparation for adding XDP handling. Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: add helpers for accessing buffer infoShannon Nelson1-13/+24
These helpers clean up some of the code around DMA mapping and other buffer references, and will be used in the next few patches for the XDP support. Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16ionic: set adminq irq affinityShannon Nelson1-1/+4
We claim to have the AdminQ on our irq0 and thus cpu id 0, but we need to be sure we set the affinity hint to try to keep it there. Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Add runtime PM supportClaudiu Beznea1-4/+50
Add runtime PM support for the ravb driver. As the driver is used by different IP variants, with different behaviors, to be able to have the runtime PM support available for all devices, the preparatory commits moved all the resources parsing and allocations in the driver's probe function and kept the settings for ravb_open(). This is due to the fact that on some IP variants-platforms tuples disabling/enabling the clocks will switch the IP to the reset operation mode where register contents is lost and reconfiguration needs to be done. For this the rabv_open() function enables the clocks, switches the IP to configuration mode, applies all the register settings and switches the IP to the operational mode. At the end of ravb_open() IP is ready to send/receive data. In ravb_close() necessary reverts are done (compared with ravb_open()), the IP is switched to reset mode and clocks are disabled. The ethtool APIs or IOCTLs that might execute while the interface is down are either cached (and applied in ravb_open()) or rejected (as at that time the IP is in reset mode). Keeping the IP in the reset mode also increases the power saved (according to the hardware manual). Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Do not apply features to hardware if the interface is downClaudiu Beznea1-1/+10
Do not apply features to hardware if the interface is down. In case runtime PM is enabled, and while the interface is down, the IP will be in reset mode (as for some platforms disabling the clocks will switch the IP to reset mode, which will lead to losing register contents) and applying settings in reset mode is not an option. Instead, cache the features and apply them in ravb_open() through ravb_emac_init(). To avoid accessing the hardware while the interface is down pm_runtime_active() check was introduced. Along with it the device runtime PM usage counter has been incremented to avoid disabling the device clocks while the check is in progress (if any). Commit prepares for the addition of runtime PM. Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Move the update of ndev->features to ravb_set_features()Claudiu Beznea1-4/+8
Commit c2da9408579d ("ravb: Add Rx checksum offload support for GbEth") introduced support for setting GbEth features. With this the IP-specific features update functions update the ndev->features individually. Next commits add runtime PM support for the ravb driver. The runtime PM implementation will enable/disable the IP clocks on the ravb_open()/ravb_close() functions. Accessing the IP registers with clocks disabled blocks the system. The ravb_set_features() function could be executed when the Ethernet interface is closed so we need to ensure we don't access IP registers while the interface is down when runtime PM support will be in place. For these, move the update of ndev->features to ravb_set_features(). In this way we update the ndev->features only when the IP-specific features set function returns success and we can avoid code duplication when introducing runtime PM registers protection. Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Return cached statistics if the interface is downClaudiu Beznea1-0/+12
Return the cached statistics in case the interface is down. There should be no drawback to this, as cached statistics are updated in ravb_close(). In order to avoid accessing the IP registers while the IP is runtime suspended pm_runtime_active() check was introduced. The device runtime PM usage counter has been incremented to avoid disabling the device clocks while the check is in progress (if any). The commit prepares the code for the addition of runtime PM support. Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Keep the reverse order of operations in ravb_close()Claudiu Beznea1-8/+8
Keep the reverse order of operations in ravb_close() when compared with ravb_open(). This is the recommended configuration sequence. Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-16net: ravb: Get rid of the temporary variable irqClaudiu Beznea1-13/+16
The 4th argument of ravb_setup_irq() is used to save the IRQ number that will be further used by the driver code. Not all ravb_setup_irqs() calls need to save the IRQ number. The previous code used to pass a dummy variable as the 4th argument in case the IRQ is not needed for further usage. That is not necessary as the code from ravb_setup_irq() can detect by itself if the IRQ needs to be saved. Thus, get rid of the code that is not needed. Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski49-174/+289
Cross-merge networking fixes after downstream PR. No conflicts. Adjacent changes: net/core/dev.c 9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()") 723de3ebef03 ("net: free altname using an RCU callback") net/unix/garbage.c 11498715f266 ("af_unix: Remove io_uring code for GC.") 25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.") drivers/net/ethernet/renesas/ravb_main.c ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path" ) c2da9408579d ("ravb: Add Rx checksum offload support for GbEth") net/mptcp/protocol.c bdd70eb68913 ("mptcp: drop the push_pending field") 28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15Merge branch '1GbE' of ↵Jakub Kicinski3-23/+20
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-02-06 (igb, igc) This series contains updates to igb and igc drivers. Kunwu Chan adjusts firmware version string implementation to resolve possible NULL pointer issue for igb. Sasha removes workaround on igc. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: igc: Remove temporary workaround igb: Fix string truncation warnings in igb_set_fw_version ==================== Link: https://lore.kernel.org/r/20240214180347.3219650-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for missing arcnetBreno Leitao10-0/+10
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the ARC modules. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240214152741.670178-8-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for mdio_devresBreno Leitao1-0/+1
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the PHY MDIO helpers. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240214152741.670178-7-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for pppBreno Leitao5-0/+5
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the PPP modules. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240214152741.670178-6-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for fddik/skfpBreno Leitao1-0/+1
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the SysKonnect FDDI PCI module. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240214152741.670178-5-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for plipBreno Leitao1-0/+1
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the PLIP (parallel port) network module Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240214152741.670178-4-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for ieee802154/fakelbBreno Leitao1-0/+1
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the IEEE 802.15.4 loopback driver. Signed-off-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/20240214152741.670178-3-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: fill in MODULE_DESCRIPTION()s for xen-netbackBreno Leitao1-0/+1
W=1 builds now warn if module is built without a MODULE_DESCRIPTION(). Add descriptions to the Xen backend network module. Signed-off-by: Breno Leitao <leitao@debian.org> Acked-by: Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/20240214152741.670178-2-leitao@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15net: ravb: Count packets instead of descriptors in GbEth RX pathPaul Barker1-13/+9
The units of "work done" in the RX path should be packets instead of descriptors, as large packets can be spread over multiple descriptors. Fixes: 1c59eb678cbd ("ravb: Fillup ravb_rx_gbeth() stub") Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Link: https://lore.kernel.org/r/20240214151204.2976-1-paul.barker.ct@bp.renesas.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15pppoe: Fix memory leak in pppoe_sendmsg()Gavrilov Ilia1-14/+9
syzbot reports a memory leak in pppoe_sendmsg [1]. The problem is in the pppoe_recvmsg() function that handles errors in the wrong order. For the skb_recv_datagram() function, check the pointer to skb for NULL first, and then check the 'error' variable, because the skb_recv_datagram() function can set 'error' to -EAGAIN in a loop but return a correct pointer to socket buffer after a number of attempts, though 'error' remains set to -EAGAIN. skb_recv_datagram __skb_recv_datagram // Loop. if (err == -EAGAIN) then // go to the next loop iteration __skb_try_recv_datagram // if (skb != NULL) then return 'skb' // else if a signal is received then // return -EAGAIN Found by InfoTeCS on behalf of Linux Verification Center (linuxtesting.org) with Syzkaller. Link: https://syzkaller.appspot.com/bug?extid=6bdfd184eac7709e5cc9 [1] Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+6bdfd184eac7709e5cc9@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6bdfd184eac7709e5cc9 Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Guillaume Nault <gnault@redhat.com> Link: https://lore.kernel.org/r/20240214085814.3894917-1-Ilia.Gavrilov@infotecs.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-15igc: Add support for LEDs on i225/i226Kurt Kanzenbach6-0/+301
Add support for LEDs on i225/i226. The LEDs can be controlled via sysfs from user space using the netdev trigger. The LEDs are named as igc-<bus><device>-<led> to be easily identified. Offloading link speed and activity are supported. Other modes are simulated in software by using on/off. Tested on Intel i225. Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240213184138.1483968-1-anthony.l.nguyen@intel.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15net: bcmasp: Handle RX buffer allocation failureFlorian Fainelli1-0/+3
The buffer_pg variable needs to hold an order-5 allocation (32 x PAGE_SIZE) which, under memory pressure may fail to be allocated. Deal with that error condition properly to avoid doing a NULL pointer de-reference in the subsequent call to dma_map_page(). In addition, the err_reclaim_tx error label in bcmasp_netif_init() needs to ensure that the TX NAPI object is properly deleted, otherwise unregister_netdev() will spin forever attempting to test and clear the NAPI_STATE_HASHED bit. Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller") Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Justin Chen <justin.chen@broadcom.com> Link: https://lore.kernel.org/r/20240213173339.3438713-1-florian.fainelli@broadcom.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15net: ena: Remove unlikely() from IS_ERR() conditionKamal Heib1-1/+1
IS_ERR() is already using unlikely internally. Signed-off-by: Kamal Heib <kheib@redhat.com> Acked-by: Arthur Kiyanovski <akiyano@amazon.com> Link: https://lore.kernel.org/r/20240213161502.2297048-1-kheib@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15net: mdio_bus: make mdio_bus_type constRicardo B. Marliere2-3/+2
Since commit d492cc2573a0 ("driver core: device.h: make struct bus_type a const *"), the driver core can properly handle constant struct bus_type, move the mdio_bus_type variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20240213-bus_cleanup-mdio-v1-1-f9e799da7fda@marliere.net Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15net: phy: aquantia: add AQR111 and AQR111B0 PHY IDChristian Marangi1-0/+52
Add Aquantia AQR111 and AQR111B0 PHY ID. These PHY advertise 10G speed but actually supports up to 5G speed, hence some manual fixup is needed. The Aquantia AQR111B0 PHY is just a variant of the AQR111 with smaller chip size. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240213133558.1836-1-ansuelsmth@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15Merge tag 'linux-can-fixes-for-6.8-20240214' of ↵Paolo Abeni1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2024-02-14 this is a pull request of 3 patches for net/master. the first patch is by Ziqi Zhao and targets the CAN J1939 protocol, it fixes a potential deadlock by replacing the spinlock by an rwlock. Oleksij Rempel's patch adds a missing spin_lock_bh() to prevent a potential Use-After-Free in the CAN J1939's setsockopt(SO_J1939_FILTER). Maxime Jayat contributes a patch to fix the transceiver delay compensation (TDCO) calculation, which is needed for higher CAN-FD bit rates (usually 2Mbit/s). * tag 'linux-can-fixes-for-6.8-20240214' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: netlink: Fix TDCO calculation using the old data bittiming can: j1939: Fix UAF in j1939_sk_match_filter during setsockopt(SO_J1939_FILTER) can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock ==================== Link: https://lore.kernel.org/r/20240214140348.2412776-1-mkl@pengutronix.de Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-15net: phy: qca807x: move interface mode check to .config_init_onceRobert Marko1-5/+5
Currently, we are checking whether the PHY package mode matches the individual PHY interface modes at PHY package probe time, but at that time we only know the PHY package mode and not the individual PHY interface modes as of_get_phy_mode() that populates it will only get called once the netdev to which PHY-s are attached to is being probed and thus this check will always fail and return -EINVAL. So, lets move this check to .config_init_once as at that point individual PHY interface modes should be populated. Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family") Signed-off-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240212115043.1725918-1-robimarko@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2024-02-14ice: Add check for lport extraction to LAG initDave Ertman2-2/+26
To fully support initializing the LAG support code, a DDP package that extracts the logical port from the metadata is required. If such a package is not present, there could be difficulties in supporting some bond types. Add a check into the initialization flow that will bypass the new paths if any of the support pieces are missing. Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Fixes: df006dd4b1dc ("ice: Add initial support framework for LAG") Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20240213183957.1483857-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-14Merge tag 'wireless-2024-02-14' of ↵Jakub Kicinski5-17/+77
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless Johannes Berg says: ==================== Valentine's day edition, with just few fixes because that's how we love it ;-) iwlwifi: - correct A3 in A-MSDUs - fix crash when operating as AP and running out of station slots to use - clear link ID to correct some later checks against it - fix error codes in SAR table loading - fix error path in PPAG table read mac80211: - reload a pointer after SKB may have changed (only in certain monitor inject mode scenarios) * tag 'wireless-2024-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: wifi: iwlwifi: mvm: fix a crash when we run out of stations wifi: iwlwifi: uninitialized variable in iwl_acpi_get_ppag_table() wifi: iwlwifi: Fix some error codes wifi: iwlwifi: clear link_id in time_event wifi: iwlwifi: mvm: use correct address 3 in A-MSDU wifi: mac80211: reload info pointer in ieee80211_tx_dequeue() ==================== Link: https://lore.kernel.org/r/20240214184326.132813-3-johannes@sipsolutions.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-02-14igc: Remove temporary workaroundSasha Neftin1-5/+1
PHY_CONTROL register works as defined in the IEEE 802.3 specification (IEEE 802.3-2008 22.2.4.1). Tidy up the temporary workaround. User impact: PHY can now be powered down when the ethernet link is down. Testing hints: ip link set down <device> (or just disconnect the ethernet cable). Oldest tested NVM version is: 1045:740. Fixes: 5586838fe9ce ("igc: Add code for PHY support") Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-14igb: Fix string truncation warnings in igb_set_fw_versionKunwu Chan2-18/+19
Commit 1978d3ead82c ("intel: fix string truncation warnings") fixes '-Wformat-truncation=' warnings in igb_main.c by using kasprintf. drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning：‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=] 3092 | "%d.%d, 0x%08x, %d.%d.%d", | ^~ drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535] 3092 | "%d.%d, 0x%08x, %d.%d.%d", | ^~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535] drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note：‘snprintf’ output between 23 and 43 bytes into a destination of size 32 kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Fix this warning by using a larger space for adapter->fw_version, and then fall back and continue to use snprintf. Fixes: 1978d3ead82c ("intel: fix string truncation warnings") Signed-off-by: Kunwu Chan <chentao@kylinos.cn> Cc: Kunwu Chan <kunwu.chan@hotmail.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2024-02-14can: netlink: Fix TDCO calculation using the old data bittimingMaxime Jayat1-1/+1
The TDCO calculation was done using the currently applied data bittiming, instead of the newly computed data bittiming, which means that the TDCO had an invalid value unless setting the same data bittiming twice. Fixes: d99755f71a80 ("can: netlink: add interface for CAN-FD Transmitter Delay Compensation (TDC)") Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/all/40579c18-63c0-43a4-8d4c-f3a6c1c0b417@munic.io Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2024-02-14ethernet: cpts: fix function pointer cast warningsArnd Bergmann1-5/+12
clang-16 warns about the mismatched prototypes for the devm_* callbacks: drivers/net/ethernet/ti/cpts.c:691:12: error: cast from 'void (*)(struct clk_hw *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict] 691 | (void(*)(void *))clk_hw_unregister_mux, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ include/linux/device.h:406:34: note: expanded from macro 'devm_add_action_or_reset' 406 | __devm_add_action_or_reset(dev, action, data, #action) | ^~~~~~ drivers/net/ethernet/ti/cpts.c:703:12: error: cast from 'void (*)(struct device_node *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict] 703 | (void(*)(void *))of_clk_del_provider, | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ include/linux/device.h:406:34: note: expanded from macro 'devm_add_action_or_reset' 406 | __devm_add_action_or_reset(dev, action, data, #action) Use separate helper functions for this instead, using the expected prototypes with a void* argument. Fixes: a3047a81ba13 ("net: ethernet: ti: cpts: add support for ext rftclk selection") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-14bnad: fix work_queue type mismatchArnd Bergmann1-7/+5
clang-16 warns about a function pointer cast: drivers/net/ethernet/brocade/bna/bnad.c:1995:4: error: cast from 'void (*)(struct delayed_work *)' to 'work_func_t' (aka 'void (*)(struct work_struct *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict] 1995 | (work_func_t)bnad_tx_cleanup); drivers/net/ethernet/brocade/bna/bnad.c:2252:4: error: cast from 'void (*)(void *)' to 'work_func_t' (aka 'void (*)(struct work_struct *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict] 2252 | (work_func_t)(bnad_rx_cleanup)); The problem here is mixing up work_struct and delayed_work, which relies the former being the first member of the latter. Change the code to use consistent types here to address the warning and make it more robust against workqueue interface changes. Side note: the use of a delayed workqueue for cleaning up TX descriptors is probably a bad idea since this introduces a noticeable delay. The driver currently does not appear to use BQL, but if one wanted to add that, this would have to be changed as well. Fixes: 01b54b145185 ("bna: tx rx cleanup fix") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-02-14net: phy: dp83826: support TX data voltage tuningCatalin Popescu1-4/+126
DP83826 offers the possibility to tune the voltage of logical levels of the MLT-3 encoded TX data. This is useful when there is a voltage drop in between the PHY and the connector and we want to increase the voltage levels to compensate for that drop. Prior to PHY configuration, the driver SW resets the PHY which has the same effect as the HW reset pi