summaryrefslogtreecommitdiff
path: root/drivers/pci/controller/dwc/pci-imx6.c
AgeCommit message (Collapse)AuthorFilesLines
2023-06-19PCI: imx6: Save and restore root port MSI control in suspend and resumeRichard Zhu1-0/+23
The imx6 PCI host controller suffers from a HW integration bug whereby the MSI enable bit in the root port MSI capability enables/disables MSIs interrupts for all downstream components in the PCI tree. This requires, as implemented in 75cb8d20c112 ("PCI: imx: Enable MSI from downstream components") that the root port MSI enable bit should be set in order for downstream PCI devices MSIs to function. The MSI enable bit programming might be lost during the suspend and should be re-stored during resume. Save the MSI control during suspend and restore it in resume. Link: https://lore.kernel.org/r/1670479534-22154-1-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> [lpieralisi@kernel.org: commit log] Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2023-03-24PCI: imx6: Install the fault handler only on compatible matchH. Nikolaus Schaller1-0/+7
commit bb38919ec56e ("PCI: imx6: Add support for i.MX6 PCIe controller") added a fault hook to this driver in the probe function. So it was only installed if needed. commit bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO") moved it from probe to driver init which installs the hook unconditionally as soon as the driver is compiled into a kernel. When this driver is compiled as a module, the hook is not registered until after the driver has been matched with a .compatible and loaded. commit 415b6185c541 ("PCI: imx6: Fix config read timeout handling") extended the fault handling code. commit 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ") added some protection for non-ARM architectures, but this does not protect non-i.MX ARM architectures. Since fault handlers can be triggered on any architecture for different reasons, there is no guarantee that they will be triggered only for the assumed situation, leading to improper error handling (i.MX6-specific imx6q_pcie_abort_handler) on foreign systems. I had seen strange L3 imprecise external abort messages several times on OMAP4 and OMAP5 devices and couldn't make sense of them until I realized they were related to this unused imx6q driver because I had CONFIG_PCI_IMX6=y. Note that CONFIG_PCI_IMX6=y is useful for kernel binaries that are designed to run on different ARM SoC and be differentiated only by device tree binaries. So turning off CONFIG_PCI_IMX6 is not a solution. Therefore we check the compatible in the init function before registering the fault handler. Link: https://lore.kernel.org/r/e1bcfc3078c82b53aa9b78077a89955abe4ea009.1678380991.git.hns@goldelico.com Fixes: bde4a5a00e76 ("PCI: imx6: Allow probe deferral by reset GPIO") Fixes: 415b6185c541 ("PCI: imx6: Fix config read timeout handling") Fixes: 2d8ed461dbc9 ("PCI: imx6: Add support for i.MX8MQ") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
2023-01-16PCI: imx6: Add i.MX8MP PCIe EP supportRichard Zhu1-1/+18
Add the i.MX8MP PCIe EP support. Link: https://lore.kernel.org/r/1673847684-31893-15-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2023-01-16PCI: imx6: Add i.MX8MM PCIe EP supportRichard Zhu1-0/+17
Add i.MX8MM PCIe EP support. Link: https://lore.kernel.org/r/1673847684-31893-14-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2023-01-16PCI: imx6: Add i.MX8MQ PCIe EP supportRichard Zhu1-5/+33
Add i.MX8MQ PCIe EP support. Link: https://lore.kernel.org/r/1673847684-31893-13-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2023-01-16PCI: imx6: Add i.MX PCIe EP mode supportRichard Zhu1-13/+115
i.MX PCIe is one dual mode PCIe controller. Add i.MX PCIe EP mode support here, and split the PCIe modes to the Root Complex mode and Endpoint mode. Link: https://lore.kernel.org/r/1673847684-31893-12-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-11-11PCI: imx6: Initialize PHY before deasserting core resetSascha Hauer1-6/+7
When the PHY is the reference clock provider then it must be initialized and powered on before the reset on the client is deasserted, otherwise the link will never come up. The order was changed in cf236e0c0d59. Restore the correct order to make the driver work again on boards where the PHY provides the reference clock. This also changes the order for boards where the Soc is the PHY reference clock divider, but this shouldn't do any harm. Link: https://lore.kernel.org/r/20221101095714.440001-1-s.hauer@pengutronix.de Fixes: cf236e0c0d59 ("PCI: imx6: Do not hide PHY driver callbacks and refine the error handling") Tested-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-10-03phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()Richard Zhu1-3/+3
Refer to phy_core driver, phy_init() must be called before phy_power_on(). Fix the wrong order of phy_init() and phy_power_on() here. Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com Fixes: 1aa97b002258 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver") Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Acked-by: Vinod Koul <vkoul@kernel.org> Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
2022-10-03PCI: imx6: Add i.MX8MP PCIe supportRichard Zhu1-2/+25
Add i.MX8MP PCIe support. To avoid codes duplication when find the syscon regmap, add the iomux gpr syscon compatible into drvdata. Link: https://lore.kernel.org/r/1662109086-15881-8-git-send-email-hongxing.zhu@nxp.com Tested-by: Marek Vasut <marex@denx.de> Tested-by: Richard Leitner <richard.leitner@skidata.com> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Support more than Gen2 speed link modeRichard Zhu1-4/+4
Support more than Gen2 speed link mode, since i.MX8MP PCIe supports up to Gen3 link speed. Link: https://lore.kernel.org/r/1658287576-26908-1-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registersRichard Zhu1-0/+4
The PCIE_DBI_RO_WR_EN bit should be set when write some DBI registers. To make sure that the DBI registers are writable, set the PCIE_DBI_RO_WR_EN properly when writing the DBI registers. Link: https://lore.kernel.org/r/1652866528-13220-1-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Reformat suspend callback to keep symmetric with resumeRichard Zhu1-25/+37
Create imx6_pcie_stop_link() and imx6_pcie_host_exit() functions. Encapsulate clocks, regulators disables and PHY uninitialization into imx6_pcie_host_exit(). To keep suspend/resume symmetric as much as possible, invoke these two new created functions in suspend callback. To be symmetric with imx6_pcie_host_exit(), move imx6_pcie_clk_enable() to imx6_pcie_host_init() from imx6_pcie_deassert_core_reset(). Link: https://lore.kernel.org/r/1657783869-19194-18-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Move the imx6_pcie_ltssm_disable() earlierRichard Zhu1-19/+19
Move the imx6_pcie_ltssm_disable() earlier and place it just behind the imx6_pcie_ltssm_enable(), since it might not be only used by suspend callback directly. To be symmetric with imx6_pcie_ltssm_enable(), add the IMX6Q and IMX8MQ switch cases in imx6_pcie_ltssm_disable(). Link: https://lore.kernel.org/r/1657783869-19194-17-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Disable clocks in reverse order of enableBjorn Helgaas1-2/+2
imx6_pcie_clk_enable() enables clocks in the order: pcie_phy pcie_bus pcie imx6_pcie_enable_ref_clk Change imx6_pcie_clk_disable() to disable them in the reverse order. Link: https://lore.kernel.org/r/1657783869-19194-16-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-08-01PCI: imx6: Do not hide PHY driver callbacks and refine the error handlingRichard Zhu1-13/+23
Move the phy_power_on() to host_init from imx6_pcie_clk_enable(). Move the phy_init() to host_init from imx6_pcie_deassert_core_reset(). Refine the error handling in imx6_pcie_host_init() accordingly. Link: https://lore.kernel.org/r/1657783869-19194-15-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Reduce resume time by only starting link if it was up before suspendRichard Zhu1-1/+6
i.MX PCIe doesn't support hotplug. During resume, only start PCIe link training when the link was up before system suspend to avoid the long latency in the link training period. Link: https://lore.kernel.org/r/1657783869-19194-14-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Mark the link down as non-fatal errorRichard Zhu1-7/+8
If the PCIe link is down, return zero from imx6_pcie_start_link() so the driver will probe successfully. Link: https://lore.kernel.org/r/1657783869-19194-13-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()Richard Zhu1-20/+16
Move regulator enable out of imx6_pcie_deassert_core_reset(), since the regulator_enable() has nothing to do with imx6_pcie_deassert_core_reset(). Link: https://lore.kernel.org/r/1657783869-19194-12-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Turn off regulator when system is in suspend modeRichard Zhu1-12/+5
The driver should undo any enables it did itself. The regulator disable shouldn't be basing decisions on regulator_is_enabled(). Move the regulator_disable to the suspend function, turn off regulator when the system is in suspend mode. Link: https://lore.kernel.org/r/1657783869-19194-11-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2022-08-01PCI: imx6: Call host init function directly in resumeRichard Zhu1-3/+3
Call imx6_pcie_host_init() instead of duplicating codes in resume. Note that this also means we do MPLL setup again during resume, which we didn't do before. [bhelgaas: add MPLL setup note, pointed out by Lucas] Link: https://lore.kernel.org/r/1657783869-19194-10-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Disable i.MX6QDL clock when disabling ref clocksRichard Zhu1-0/+8
When disabling PCIe clocks, disable i.MX6QDL ref clock too. Link: https://lore.kernel.org/r/1657783869-19194-9-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Propagate .host_init() errors to callerRichard Zhu1-4/+12
Since dw_pcie_host_init() checks for errors from ops->host_init(), check for errors when enabling power regulators and clocks and return them. [bhelgaas: commit log] Link: https://lore.kernel.org/r/1657783869-19194-8-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()Richard Zhu1-39/+56
Encapsulate the i.MX PCIe clock enable operations into one standalone function, imx6_pcie_clk_enable(). No functional change intended. [bhelgaas: split pure code moves into separate patches] Link: https://lore.kernel.org/r/1657783869-19194-7-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Factor out ref clock disable to match enableBjorn Helgaas1-6/+10
The PCIe ref clocks are specific to different variants. The enables are already split out into imx6_pcie_enable_ref_clk(), but the disables were combined with the more generic bus/phy/pcie clock disables in imx6_pcie_clk_disable(). Split out the variant-specific disables into imx6_pcie_disable_ref_clk() to match imx6_pcie_enable_ref_clk(). No functional change intended. Link: https://lore.kernel.org/r/1657783869-19194-6-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-08-01PCI: imx6: Move imx6_pcie_clk_disable() earlierRichard Zhu1-24/+24
Move imx6_pcie_clk_disable() earlier to be near other clock-related functions. No functional change intended. [bhelgaas: reorder patch so pure moves are earlier] Link: https://lore.kernel.org/r/1657783869-19194-5-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-08-01PCI: imx6: Move imx6_pcie_enable_ref_clk() earlierBjorn Helgaas1-48/+48
Move imx6_pcie_enable_ref_clk() earlier so it's not in the middle between imx6_pcie_assert_core_reset() and imx6_pcie_deassert_core_reset(). No functional change intended. Link: https://lore.kernel.org/r/1657783869-19194-4-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-08-01PCI: imx6: Move PHY management functions togetherBjorn Helgaas1-128/+128
Collect imx6_pcie_init_phy(), imx7d_pcie_wait_for_phy_pll_lock(), and imx6_setup_phy_mpll() earlier with other PHY-related code. No functional change intended. Link: https://lore.kernel.org/r/1657783869-19194-3-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-08-01PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlierBjorn Helgaas1-25/+25
Move imx6_pcie_grp_offset() and imx6_pcie_configure_type() earlier in the file since they depend on nothing and are used by several other functions that will be moved earlier. No functional change intended. Link: https://lore.kernel.org/r/1657783869-19194-2-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-08-01PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()Bjorn Helgaas1-4/+2
Replace SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() with NOIRQ_SYSTEM_SLEEP_PM_OPS(), which has the advantage that the compiler always sees the PM callbacks as referenced, so they don't need to be wrapped with "#ifdef CONFIG_PM_SLEEP" or tagged with "__maybe_unused" to avoid "defined but not used" warnings. See 1a3c7bb08826 ("PM: core: Add new *_PM_OPS macros, deprecate old ones"). Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2022-07-05PCI: dwc: Rename struct pcie_port to dw_pcie_rpSerge Semin1-3/+3
All of the DW PCIe core driver entities except the pcie_port struct have names with the "dw_" prefix to distinguish local and common PCIe name spaces, and endpoint-related entities have an "_ep" suffix. Rename struct pcie_port to dw_pcie_rp to make it more consistent with other names. [bhelgaas: commit log] Link: https://lore.kernel.org/r/20220624143428.8334-16-Sergey.Semin@baikalelectronics.ru Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
2022-05-11PCI: imx6: Fix PERST# start-up sequenceFrancesco Dolcini1-9/+14
According to the PCIe standard the PERST# signal (reset-gpio in fsl,imx* compatible dts) should be kept asserted for at least 100 usec before the PCIe refclock is stable, should be kept asserted for at least 100 msec after the power rails are stable and the host should wait at least 100 msec after it is de-asserted before accessing the configuration space of any attached device. From PCIe CEM r2.0, sec 2.6.2 T-PVPERL: Power stable to PERST# inactive - 100 msec T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec. From PCIe r5.0, sec 6.6.1 With a Downstream Port that does not support Link speeds greater than 5.0 GT/s, software must wait a minimum of 100 ms before sending a Configuration Request to the device immediately below that Port. Failure to do so could prevent PCIe devices to be working correctly, and this was experienced with real devices. Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure that PERST# is asserted before enabling any clock, move de-assert to the end of imx6_pcie_deassert_core_reset() after the clock is enabled and deemed stable and add a new delay of 100 msec just afterward. Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com Fixes: bb38919ec56e ("PCI: imx6: Add support for i.MX6 PCIe controller") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2022-03-17PCI: imx6: Assert i.MX8MM CLKREQ# even if no device presentRichard Zhu1-4/+0
The CLKREQ# signal is an open drain, active low signal that is driven low by the remote Endpoint device. But it might not be driven low if no Endpoint device is connected. On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no Endpoint is connected to assert CLKREQ#. Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the PHY can be initialized. Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-03-17PCI: imx6: Invoke the PHY exit function after PHY power offRichard Zhu1-0/+1
To balance phy->init_count, invoke the phy_exit() after phy_power_off(). Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com Fixes: 178e244cb6e2 ("PCI: imx: Add the imx8mm pcie support") Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-03-07PCI: imx6: Enable i.MX6QP PCIe power management supportRichard Zhu1-1/+3
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the initialized state when exit from L2 or L3 states. Enable the i.MX6QP PCIe suspend/resume operations support. Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2022-02-03PCI: imx6: Allow to probe when dw_pcie_wait_for_link() failsFabio Estevam1-8/+2
The intention of commit 886a9c134755 ("PCI: dwc: Move link handling into common code") was to standardize the behavior of link down as explained in its commit log: "The behavior for a link down was inconsistent as some drivers would fail probe in that case while others succeed. Let's standardize this to succeed as there are usecases where devices (and the link) appear later even without hotplug. For example, a reconfigured FPGA device." The pci-imx6 still fails to probe when the link is not present, which causes the following warning: imx6q-pcie 8ffc000.pcie: Phy link never came up imx6q-pcie: probe of 8ffc000.pcie failed with error -110 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc Modules linked in: CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1 Hardware name: Freescale i.MX6 SoloX (Device Tree) Workqueue: events_unbound async_run_entry_fn [<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14) [<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70) [<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154) [<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8) [<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc) [<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c) [<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178) Fix this problem by ignoring the dw_pcie_wait_for_link() error like it is done on the other dwc drivers. Tested on imx6sx-sdb and imx6q-sabresd boards. Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com Fixes: 886a9c134755 ("PCI: dwc: Move link handling into common code") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com> Cc: <stable@vger.kernel.org>
2021-12-26PCI: imx: Add the imx8mm pcie supportRichard Zhu1-8/+73
i.MX8MM PCIe works mostly like the i.MX8MQ one, but has a different PHY and allows to output the internal PHY reference clock via the refclk pad. Add the i.MX8MM PCIe support based on the standalone PHY driver. Link: https://lore.kernel.org/r/1640312885-31142-2-git-send-email-hongxing.zhu@nxp.com Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com>
2021-10-05PCI: imx6: Remove unused assignment to variable retKrzysztof Wilczyński1-1/+1
Previously, the maximum link speed was set following an "fsl,max-link-speed" property read, and should the read failed, then the PCIe generation was manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s. Code refactoring completed in the commit 39bc5006501c ("PCI: dwc: Centralize link gen setting") changed to the logic that was previously used to limit the maximum link speed leaving behind an unused assignment to a variable "ret". Since the value returned from the of_property_read_u32() and stored in the variable "ret" is never used in any meaningful way, and it's also immediately reassigned in the code that follows, the assignment can be removed. Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.com Signed-off-by: Krzysztof Wilczyński <kw@linux.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2021-06-24PCI: imx6: Enable PHY internal regulator when supplied >3VRichard Zhu1-0/+20
The i.MX8MQ PCIe PHY needs 1.8V in default but can be supplied by either a 1.8V or a 3.3V regulator. The "vph-supply" DT property tells us which external regulator supplies the PHY. If that regulator supplies anything over 3V, enable the PHY's internal 3.3V-to-1.8V regulator. Link: https://lore.kernel.org/r/1622771269-13844-3-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
2021-06-24PCI: imx6: Limit DBI register length for imx6qp PCIeRichard Zhu1-0/+1
Define the length of the DBI registers and limit config space to its length. This makes sure that the kernel does not access registers beyond that point that otherwise would lead to an abort on the i.MX 6QuadPlus. See commit 075af61c19cd ("PCI: imx6: Limit DBI register length") that resolves a similar issue on the i.MX 6Quad PCIe. Link: https://lore.kernel.org/r/1613789388-2495-2-git-send-email-hongxing.zhu@nxp.com Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
2021-06-24PCI: imx6: Remove imx6_pcie_probe() redundant error messageZhen Lei1-3/+1
When devm_ioremap_resource() fails, __devm_ioremap_resource() prints an error message including the device name, failure cause, and possibly resource information. Remove the error message from imx6_pcie_probe() since it's redundant. Link: https://lore.kernel.org/r/20210511114547.5601-1-thunder.leizhen@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Krzysztof Wilczyński <kw@linux.com> Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
2020-11-19PCI: dwc: Remove unnecessary wrappers around dw_pcie_host_init()Rob Herring1-20/+2
Many calls to dw_pcie_host_init() are in a wrapper function with nothing else now. Let's remove the pointless extra layer. Link: https://lore.kernel.org/r/20201105211159.1814485-14-robh@kernel.org Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: Minghuan Lian <minghuan.Lian@nxp.com> Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: Roy Zang <roy.zang@nxp.com> Cc: Yue Wang <yue.wang@Amlogic.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Jonathan Chocron <jonnyc@amazon.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Xiaowei Song <songxiaowei@hisilicon.com> Cc: Binghui Wang <wangbinghui@hisilicon.com> Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@axis.com
2020-11-19PCI: dwc: Move dw_pcie_setup_rc() to DWC common codeRob Herring1-1/+0
All RC complex drivers must call dw_pcie_setup_rc(). The ordering of the call shouldn't be too important other than being after any RC resets. There's a few calls of dw_pcie_setup_rc() left as drivers implementing suspend/resume need it. Link: https://lore.kernel.org/r/20201105211159.1814485-13-robh@kernel.org Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Jingoo Han <jingoohan1@gmail.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: Minghuan Lian <minghuan.Lian@nxp.com> Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: Roy Zang <roy.zang@nxp.com> Cc: Yue Wang <yue.wang@Amlogic.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Xiaowei Song <songxiaowei@hisilicon.com> Cc: Binghui Wang <wangbinghui@hisilicon.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Stanimir Varbanov <svarbanov@mm-sol.com> Cc: Pratyush Anand <pratyush.anand@gmail.com> Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@axis.com Cc: linux-arm-msm@vger.kernel.org
2020-11-19PCI: dwc: Move dw_pcie_msi_init() into coreRob Herring1-1/+0
The host drivers which call dw_pcie_msi_init() are all the ones using the built-in MSI controller, so let's move it into the common DWC code. Link: https://lore.kernel.org/r/20201105211159.1814485-12-robh@kernel.org Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Jingoo Han <jingoohan1@gmail.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Yue Wang <yue.wang@Amlogic.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Xiaowei Song <songxiaowei@hisilicon.com> Cc: Binghui Wang <wangbinghui@hisilicon.com> Cc: Stanimir Varbanov <svarbanov@mm-sol.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Pratyush Anand <pratyush.anand@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@axis.com Cc: linux-arm-msm@vger.kernel.org Cc: linux-tegra@vger.kernel.org
2020-11-19PCI: dwc: Move link handling into common codeRob Herring1-5/+4
All the DWC drivers do link setup and checks at roughly the same time. Let's use the existing .start_link() hook (currently only used in EP mode) and move the link handling to the core code. The behavior for a link down was inconsistent as some drivers would fail probe in that case while others succeed. Let's standardize this to succeed as there are usecases where devices (and the link) appear later even without hotplug. For example, a reconfigured FPGA device. Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.org Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Jingoo Han <jingoohan1@gmail.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: Yue Wang <yue.wang@Amlogic.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Xiaowei Song <songxiaowei@hisilicon.com> Cc: Binghui Wang <wangbinghui@hisilicon.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Stanimir Varbanov <svarbanov@mm-sol.com> Cc: Pratyush Anand <pratyush.anand@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@axis.com Cc: linux-arm-msm@vger.kernel.org Cc: linux-tegra@vger.kernel.org
2020-11-19PCI: dwc: Move MSI interrupt setup into DWC common codeRob Herring1-6/+0
Platforms using the built-in DWC MSI controller all have a dedicated interrupt with "msi" name or at index 0, so let's move setting up the interrupt to the common DWC code. spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so we need to prevent configuring the MSI interrupt by setting msi_irq to negative. Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.org Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Jingoo Han <jingoohan1@gmail.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Kukjin Kim <kgene@kernel.org> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Yue Wang <yue.wang@Amlogic.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Jerome Brunet <jbrunet@baylibre.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Jesper Nilsson <jesper.nilsson@axis.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Xiaowei Song <songxiaowei@hisilicon.com> Cc: Binghui Wang <wangbinghui@hisilicon.com> Cc: Stanimir Varbanov <svarbanov@mm-sol.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Pratyush Anand <pratyush.anand@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: linux-samsung-soc@vger.kernel.org Cc: linux-amlogic@lists.infradead.org Cc: linux-arm-kernel@axis.com Cc: linux-arm-msm@vger.kernel.org Cc: linux-tegra@vger.kernel.org
2020-10-21Merge branch 'remotes/lorenzo/pci/imx6'Bjorn Helgaas1-23/+18
- Use "fallthrough" pseudo-keyword (Gustavo A. R. Silva) - Drop redundant error messages after devm_clk_get() (Anson Huang) * remotes/lorenzo/pci/imx6: PCI: imx6: Do not output error message when devm_clk_get() failed with -EPROBE_DEFER PCI: imx6: Use fallthrough pseudo-keyword
2020-09-10PCI: dwc: Centralize link gen settingRob Herring1-6/+3
keystone would force gen2 if no DT property. Now it relies on the PCI_EXP_LNKCAP value. Link: https://lore.kernel.org/r/20200821035420.380495-35-robh@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: Jingoo Han <jingoohan1@gmail.com> Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Cc: Stanimir Varbanov <svarbanov@mm-sol.com> Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Pratyush Anand <pratyush.anand@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Jonathan Hunter <jonathanh@nvidia.com> Cc: linux-omap@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-arm-msm@vger.kernel.org Cc: linux-tegra@vger.kernel.org
2020-09-08PCI: dwc/imx6: Use common PCI register definitionsRob Herring1-23/+14
The i.MX6 driver has its own defines for common PCI config space registers. It also hard codes the capability register offsets which are discoverable. Convert it to use the standard register definitions. Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Richard Zhu <hongxing.zhu@nxp.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com>
2020-09-08PCI: dwc/imx6: Remove duplicate define PCIE_LINK_WIDTH_SPEED_CONTROLRob Herring1-2/