| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
|
|
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a flood
(Manivannan Sadhasivam)
- Add Manivannan Sadhasivam as maintainer of qcom endpoint driver
(Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for endpoint
controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding (Manivannan
Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't overlap BAR
MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is deasserted to
partially avoid the problem that the endpoint SoC crashes when accessing
things when Refclk is absent (Manivannan Sadhasivam)
- Rename dw_pcie.link_gen to max_link_speed to avoid ambiguity (Manivannan
Sadhasivam)
- Cache maximum link speed value in dw_pcie.max_link_speed for use by
vendor drivers (Manivannan Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank Babu
Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to avoid a
NULL pointer dereference (Manivannan Sadhasivam)
* pci/controller/qcom:
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: qcom: Disable mirroring of DBI and iATU register space in BAR region
PCI: qcom: Enumerate endpoints based on Link up event in 'global_irq' interrupt
dt-bindings: PCI: qcom,pcie-sm8450: Add 'global' interrupt
PCI: qcom-ep: Modify 'global_irq' and 'perst_irq' IRQ device names
PCI: endpoint: Assign PCI domain number for endpoint controllers
dt-bindings: PCI: pci-ep: Document 'linux,pci-domain' property
dt-bindings: PCI: pci-ep: Update Maintainers
PCI: qcom-ep: Reword the error message for receiving unknown global IRQ event
PCI: qcom-ep: Drop the redundant masking of global IRQ events
|
|
- Wait for each level of downstream bus, not just the first, to become
accessible before restoring devices on that bus (Ilpo Järvinen)
* pci/reset:
PCI: Wait for Link before restoring Downstream Buses
|
|
- Clear LBMS bit after a manual link retrain so we don't try to retrain a
link when there's no downstream device anymore (Maciej W. Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance to use
higher speeds (Maciej W. Rozycki)
- Correct interpretation of pcie_retrain_link() return status and update it
to return 0/errno instead of true/false (Maciej W. Rozycki)
* pci/enumeration:
PCI: Use an error code with PCIe failed link retraining
PCI: Correct error reporting with PCIe failed link retraining
PCI: Revert to the original speed after PCIe failed link retraining
PCI: Clear the LBMS bit after a link retrain
|
|
The pci_bus_release_domain_nr() API is supposed to free the domain
number allocated by pci_bus_find_domain_nr(). Most of the callers of
pci_bus_find_domain_nr(), store the domain number in pci_bus::domain_nr.
As such, the pci_bus_release_domain_nr() implicitly frees the domain
number by dereferencing 'struct pci_bus'. However, one of the callers
of this API, the PCI endpoint subsystem, doesn't have 'struct pci_bus',
so it only passes NULL. Due to this, the API will end up dereferencing
the NULL pointer.
To fix this issue, pass the domain number to this API explicitly. Since
'struct pci_bus' is not used for anything else other than extracting the
domain number, it makes sense to pass the domain number directly.
Fixes: 0328947c5032 ("PCI: endpoint: Assign PCI domain number for endpoint controllers")
Closes: https://lore.kernel.org/linux-pci/c0c40ddb-bf64-4b22-9dd1-8dbb18aa2813@stanley.mountain
Link: https://lore.kernel.org/linux-pci/20240912053025.25314-1-manivannan.sadhasivam@linaro.org
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
PCIe r6.0 changed the abbreviation for "Configuration Request Retry Status"
Completion Status from "CRS" to "RRS" and uses the terminology of
"Configuration RRS Software Visibility" instead of "CRS Software
Visibility".
Align the Linux usage with the r6.0 spec language. No functional change
intended.
It's confusing to make this change, but I think "RRS" *is* a better
abbreviation because it was easy to interpret "CRS" as "Completion Retry
Status", which really didn't make any sense.
Link: https://lore.kernel.org/r/20240827234848.4429-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
After a device reset, delays are required before the device can
successfully complete config accesses. PCIe r6.0, sec 6.6, specifies some
delays required before software can perform config accesses. Devices that
require more time after those delays may respond to config accesses with
Configuration Request Retry Status (RRS) completions.
Callers of pci_dev_wait() are responsible for delays until the device can
respond to config accesses. pci_dev_wait() waits any additional time until
the device can successfully complete config accesses.
Reading config space of devices that are not present or not ready typically
returns ~0 (PCI_ERROR_RESPONSE). Previously we polled the Command register
until we got a value other than ~0. This is sometimes a problem because
Root Complex handling of RRS completions may include several retries and
implementation-specific behavior that is invisible to software (see sec
2.3.2), so the exponential backoff in pci_dev_wait() may not work as
intended.
Linux enables Configuration RRS Software Visibility on all Root Ports that
support it. If it is enabled, read the Vendor ID instead of the Command
register. RRS completions cause immediate return of the 0x0001 reserved
Vendor ID value, so the pci_dev_wait() backoff works correctly.
When a read of Vendor ID eventually completes successfully by returning a
non-0x0001 value (the Vendor ID or 0xffff for VFs), the device should be
initialized and ready to respond to config requests.
For conventional PCI devices or devices below Root Ports that don't support
Configuration RRS Software Visibility, poll the Command register as before.
This was developed independently, but is very similar to Stanislav
Spassov's previous work at
https://lore.kernel.org/linux-pci/20200223122057.6504-1-stanspas@amazon.com
Link: https://lore.kernel.org/r/20240827234848.4429-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Duc Dang <ducdang@google.com>
|
|
Given how the call place in pcie_wait_for_link_delay() got structured now,
and that pcie_retrain_link() returns a potentially useful error code,
convert pcie_failed_link_retrain() to return an error code rather than a
boolean status, fixing handling at the call site mentioned. Update the
other call site accordingly.
Fixes: 1abb47390350 ("Merge branch 'pci/enumeration'")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2408091156530.61955@angie.orcam.me.uk
Reported-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/aa2d1c4e-9961-d54a-00c7-ddf8e858a9b0@linux.intel.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.5+
|
|
The LBMS bit, where implemented, is set by hardware either in response
to the completion of retraining caused by writing 1 to the Retrain Link
bit or whenever hardware has changed the link speed or width in attempt
to correct unreliable link operation. It is never cleared by hardware
other than by software writing 1 to the bit position in the Link Status
register and we never do such a write.
We currently have two places, namely apply_bad_link_workaround() and
pcie_failed_link_retrain() in drivers/pci/controller/dwc/pcie-tegra194.c
and drivers/pci/quirks.c respectively where we check the state of the LBMS
bit and neither is interested in the state of the bit resulting from the
completion of retraining, both check for a link fault.
And in particular pcie_failed_link_retrain() causes issues consequently, by
trying to retrain a link where there's no downstream device anymore and the
state of 1 in the LBMS bit has been retained from when there was a device
downstream that has since been removed.
Clear the LBMS bit then at the conclusion of pcie_retrain_link(), so that
we have a single place that controls it and that our code can track link
speed or width changes resulting from unreliable link operation.
Fixes: a89c82249c37 ("PCI: Work around PCIe link training failures")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2408091133140.61955@angie.orcam.me.uk
Reported-by: Matthew W Carlis <mattc@purestorage.com>
Link: https://lore.kernel.org/r/20240806000659.30859-1-mattc@purestorage.com/
Link: https://lore.kernel.org/r/20240722193407.23255-1-mattc@purestorage.com/
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: <stable@vger.kernel.org> # v6.5+
|
|
__pci_reset_bus() calls pci_bridge_secondary_bus_reset() to perform the
reset and also waits for the Secondary Bus to become again accessible.
__pci_reset_bus() then calls pci_bus_restore_locked() that restores the PCI
devices connected to the bus, and if necessary, recursively restores also
the subordinate buses and their devices.
The logic in pci_bus_restore_locked() does not take into account that after
restoring a device on one level, there might be another Link Downstream
that can only start to come up after restore has been performed for its
Downstream Port device. That is, the Link may require additional wait until
it becomes accessible.
Similarly, pci_slot_restore_locked() lacks wait.
Amend pci_bus_restore_locked() and pci_slot_restore_locked() to wait for
the Secondary Bus before recursively performing the restore of that bus.
Fixes: 090a3c5322e9 ("PCI: Add pci_reset_slot() and pci_reset_bus()")
Link: https://lore.kernel.org/r/20240808121708.2523-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
pci_intx() becomes managed if pcim_enable_device() has been called in
advance. Commit 25216afc9db5 ("PCI: Add managed pcim_intx()") changed this
behavior so that pci_intx() always leads to creation of a separate device
resource for itself, whereas earlier, a shared resource was used for all
PCI devres operations.
Unfortunately, pci_intx() seems to be used in some drivers' remove() paths;
in the managed case this causes a device resource to be created on driver
detach, which causes .probe() to fail if the driver is reloaded:
pci 0000:00:1f.2: Resources present before probing
Fix the regression by only redirecting pci_intx() to its managed twin
pcim_intx() if the pci_command changes.
Link: https://lore.kernel.org/r/20240725120729.59788-2-pstanner@redhat.com
Fixes: 25216afc9db5 ("PCI: Add managed pcim_intx()")
Reported-by: Damien Le Moal <dlemoal@kernel.org>
Closes: https://lore.kernel.org/all/b8f4ba97-84fc-4b7e-ba1a-99de2d9f0118@kernel.org/
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
[bhelgaas: add error message to commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Define PCIE_RESET_CONFIG_DEVICE_WAIT_MS for the generic 100ms
required after reset before config access (Kevin Xie)
- Define PCIE_T_RRS_READY_MS for the generic 100ms required after
reset before config access (probably should be unified with
PCIE_RESET_CONFIG_DEVICE_WAIT_MS) (Damien Le Moal)
Resource management:
- Rename find_resource() to find_resource_space() to be more
descriptive (Ilpo Järvinen)
- Export find_resource_space() for use by PCI core, which needs to
learn whether there is available space for a bridge window (Ilpo
Järvinen)
- Prevent double counting of resources so window size doesn't grow on
each remove/rescan cycle (Ilpo Järvinen)
- Relax bridge window sizing algorithm so a device doesn't break
simply because it was removed and rescanned (Ilpo Järvinen)
- Evaluate the ACPI PRESERVE_BOOT_CONFIG _DSM in
pci_register_host_bridge() (not acpi_pci_root_create()) so we can
unify it with similar DT functionality (Vidya Sagar)
- Extend use of DT "linux,pci-probe-only" property so it works
per-host bridge as well as globally (Vidya Sagar)
- Unify support for ACPI PRESERVE_BOOT_CONFIG _DSM and the DT
"linux,pci-probe-only" property in pci_preserve_config() (Vidya
Sagar)
Driver binding:
- Add devres infrastructure for managed request and map of partial
BAR resources (Philipp Stanner)
- Deprecate pcim_iomap_table() because uses like
"pcim_iomap_table()[0]" have no good way to return errors (Philipp
Stanner)
- Add an always-managed pcim_request_region() for use instead of
pci_request_region() and similar, which are sometimes managed
depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Reimplement pcim_set_mwi() so it doesn't need to keep store MWI
state (Philipp Stanner)
- Add pcim_intx() for use instead of pci_intx(), which is sometimes
managed depending on whether pcim_enable_device() has been called
previously (Philipp Stanner)
- Add managed pcim_iomap_range() to allow mapping of a partial BAR
(Philipp Stanner)
- Fix a devres mapping leak in drm/vboxvideo (Philipp Stanner)
Error handling:
- Add missing bridge locking in device reset path and add a warning
for other possible lock issues (Dan Williams)
- Fix use-after-free on concurrent DPC and hot-removal (Lukas Wunner)
Power management:
- Disable AER and DPC during suspend to avoid spurious wakeups if
they share an interrupt with PME (Kai-Heng Feng)
PCIe native device hotplug:
- Detect if a device was removed or replaced during system sleep so
we don't assume a new device is the one that used to be there
(Lukas Wunner)
Virtualization:
- Add an ACS quirk for Broadcom BCM5760X multi-function NIC; it
prevents transactions between functions even though it doesn't
advertise ACS, so the functions can be attached individually via
VFIO (Ajit Khaparde)
Peer-to-peer DMA:
- Add a "pci=config_acs=" kernel command-line parameter to relax
default ACS settings to enable additional peer-to-peer
configurations. Requires expert knowledge of topology and ACS
operation (Vidya Sagar)
Endpoint framework:
- Remove unused struct pci_epf_group.type_group (Christophe JAILLET)
- Fix error handling in vpci_scan_bus() and epf_ntb_epc_cleanup()
(Dan Carpenter)
- Make struct pci_epc_class constant (Greg Kroah-Hartman)
- Remove unused pci_endpoint_test_bar_{readl,writel} functions
(Jiapeng Chong)
- Rename "BME" to "Bus Master Enable" (Manivannan Sadhasivam)
- Rename struct pci_epc_event_ops.core_init() callback to epc_init()
(Manivannan Sadhasivam)
- Move DMA init to MHI .epc_init() callback for uniformity
(Manivannan Sadhasivam)
- Cancel EPF test delayed work when link goes down (Manivannan
Sadhasivam)
- Add struct pci_epc_event_ops.epc_deinit() callback for cleanup
needed on fundamental reset (Manivannan Sadhasivam)
- Add 64KB alignment to endpoint test to support Rockchip rk3588
(Niklas Cassel)
- Optimize endpoint test by using memcpy() instead of readl() (Niklas
Cassel)
Device tree bindings:
- Add generic "ats-supported" property to advertise that a PCIe Root
Complex supports ATS (Jean-Philippe Brucker)
Amazon Annapurna Labs PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
Axis ARTPEC-6 PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
Freescale i.MX6 PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
Freescale Layerscape PCIe controller driver:
- Make struct mobiveil_rp_ops constant (Christophe JAILLET)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
HiSilicon Kirin PCIe controller driver:
- Convert to agnostic GPIO API (Andy Shevchenko)
- Use _scoped() iterator for OF children to ensure refcounts are
decremented at loop exit (Javier Carrasco)
Intel VMD host bridge driver:
- Create sysfs "domain" symlink before downstream devices are exposed
to userspace by pci_bus_add_devices() (Jiwei Sun)
Loongson PCIe controller driver:
- Enable MSI when LS7A is used with new CPUs that have integrated
PCIe Root Complex, e.g., Loongson-3C6000, so downstream devices can
use MSI (Huacai Chen)
Microchip AXI PolarFlare PCIe controller driver:
- Move pcie-microchip-host.c to a new PLDA directory (Minda Chen)
- Factor PLDA generic items out to a common
plda,xpressrich3-axi-common.yaml binding (Minda Chen)
- Factor PLDA generic data structures and code out to shared
pcie-plda.h, pcie-plda-host.c (Minda Chen)
- Add PLDA generic interrupt handling with a .request_event_irq()
callback for vendor-specific events (Minda Chen)
- Add PLDA generic host init/deinit and map bus functions for use by
vendor-specific drivers (Minda Chen)
- Rework to use PLDA core (Minda Chen)
Microsoft Hyper-V host bridge driver:
- Return zero, not garbage, when reading PCI_INTERRUPT_PIN (Wei Liu)
NVIDIA Tegra194 PCIe controller driver:
- Remove unused struct tegra_pcie_soc (Dr. David Alan Gilbert)
- Set 64KB inbound ATU alignment restriction (Jon Hunter)
Qualcomm PCIe controller driver:
- Make the MHI reg region mandatory for X1E80100, since all PCIe
controllers have it (Abel Vesa)
- Prevent use of uninitialized data and possible error pointer
dereference (Dan Carpenter)
- Return error, not success, if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Add Operating Performance Points (OPP) support to scale performance
state based on aggregate link bandwidth to improve SoC power
efficiency (Krishna chaitanya chundru)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays
active even if other drivers don't vote for it (Krishna chaitanya
chundru)
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory
corruption (Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if
the link is already disabled (Manivannan Sadhasivam)
- Use new generic dw_pcie_ep_linkdown() to handle link-down events
(Manivannan Sadhasivam)
- Add DT and endpoint driver support for the SA8775P SoC (Mrinmay
Sarkar)
- Add Hyper DMA (HDMA) support for the SA8775P SoC and enable it in
the EPF MHI driver (Mrinmay Sarkar)
- Set PCIE_PARF_NO_SNOOP_OVERIDE to override the default NO_SNOOP
attribute on the SA8775P SoC (both Root Complex and Endpoint mode)
to avoid possible memory corruption (Mrinmay Sarkar)
Renesas R-Car PCIe controller driver:
- Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() to
avoid unnecessary backtrace (Marek Vasut)
- Add DT and driver support for R-Car V4H (R8A779G0) host and
endpoint. This requires separate proprietary firmware (Yoshihiro
Shimoda)
Rockchip PCIe controller driver:
- Assert PERST# for 100ms after power is stable (Damien Le Moal)
- Wait PCIE_T_RRS_READY_MS (100ms) after reset before starting
configuration (Damien Le Moal)
- Use GPIOD_OUT_LOW flag while requesting ep_gpio to fix a firmware
crash on Qcom-based modems with Rockpro64 board (Manivannan
Sadhasivam)
Rockchip DesignWare PCIe controller driver:
- Factor common parts of rockchip-dw-pcie DT binding to be shared by
Root Complex and Endpoint mode (Niklas Cassel)
- Add missing INTx signals to common DT binding (Niklas Cassel)
- Add eDMA items to DT binding for Endpoint controller (Niklas
Cassel)
- Fix initial dw-rockchip PERST# GPIO value to prevent unnecessary
short assert/deassert that causes issues with some WLAN controllers
(Niklas Cassel)
- Refactor dw-rockchip and add support for Endpoint mode (Niklas
Cassel)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Niklas Cassel)
- Add error messages in .probe() error paths to improve user
experience (Uwe Kleine-König)
Samsung Exynos PCIe controller driver:
- Use bulk clock APIs to simplify clock setup (Shradha Todi)
StarFive PCIe controller driver:
- Add DT binding and driver support for the StarFive JH7110
PLDA-based PCIe controller (Minda Chen)
Synopsys DesignWare PCIe controller driver:
- Add generic support for sending PME_Turn_Off when system suspends
(Frank Li)
- Fix incorrect interpretation of iATU slot 0 after PERST#
assert/deassert (Frank Li)
- Use msleep() instead of usleep_range() while waiting for link
(Konrad Dybcio)
- Refactor dw_pcie_edma_find_chip() to enable adding support for
Hyper DMA (HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't
auto detect this (Manivannan Sadhasivam)
- Call pci_epc_init_notify() and drop dw_pcie_ep_init_notify()
wrapper (Manivannan Sadhasivam)
- Pass the eDMA mapping format directly from drivers instead of
maintaining a capability for it (Manivannan Sadhasivam)
- Add generic dw_pcie_ep_linkdown() to notify EPF drivers about
link-down events and restore non-sticky DWC registers lost on link
down (Manivannan Sadhasivam)
- Add vendor-specific "apb" reg name, interrupt names, INTx names to
generic binding (Niklas Cassel)
- Enforce DWC restriction that 64-bit BARs must start with an
even-numbered BAR (Niklas Cassel)
- Consolidate args of dw_pcie_prog_outbound_atu() into a structure
(Yoshihiro Shimoda)
- Add support for endpoints to send Message TLPs, e.g., for INTx
emulation (Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Rename .cpu_addr_fixup() parameter to reflect that it is a PCI
address, not a CPU address (Niklas Cassel)
TI Keystone PCIe controller driver:
- Validate IORESOURCE_BUS presence to avoid NULL pointer dereference
(Aleksandr Mishin)
- Work around AM65x/DRA80xM Errata #i2037 that corrupts TLPs and
causes processor hangs by limiting Max_Read_Request_Size (MRRS) and
Max_Payload_Size (MPS) (Kishon Vijay Abraham I)
- Leave BAR 0 disabled for AM654x to fix a regression caused by
6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), which caused a 45-second boot delay (Siddharth
Vadapalli)
Xilinx Versal CPM PCIe controller driver:
- Fix overlapping bridge registers and 32-bit BAR addresses in DT
binding (Thippeswamy Havalige)
MicroSemi Switchtec management driver:
- Make struct switchtec_class constant (Greg Kroah-Hartman)
Miscellaneous:
- Remove unused struct acpi_handle_node (Dr. David Alan Gilbert)
- Add missing MODULE_DESCRIPTION() macros (Jeff Johnson)"
* tag 'pci-v6.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (154 commits)
PCI: loongson: Enable MSI in LS7A Root Complex
PCI: Extend ACS configurability
PCI: Add missing bridge lock to pci_bus_lock()
drm/vboxvideo: fix mapping leaks
PCI: Add managed pcim_iomap_range()
PCI: Remove legacy pcim_release()
PCI: Add managed pcim_intx()
PCI: vmd: Create domain symlink before pci_bus_add_devices()
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: Give pcim_set_mwi() its own devres cleanup callback
PCI: Move struct pci_devres.pinned bit to struct pci_dev
PCI: Remove struct pci_devres.enabled status bit
PCI: Document hybrid devres hazards
PCI: Add managed pcim_request_region()
PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()
PCI: Add managed partial-BAR request and map infrastructure
PCI: Add devres helpers for iomap table
PCI: Add and use devres helper for bit masks
...
|
|
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
|
|
- Warn about doing a Secondary Bus Reset without holding the device lock
(Dan Williams)
- Lock bridge in addition to downstream hierarchy before doing a Secondary
Bus Reset (Dan Williams)
* pci/reset:
PCI: Add missing bridge lock to pci_bus_lock()
PCI: Warn on missing cfg_access_lock during secondary bus reset
|
|
- If there's a device below a bridge, prevent a use-after-free by holding a
reference to the device while waiting for the secondary bus to be ready
in case the device is concurrently removed, e.g., by DPC (Lukas Wunner)
* pci/dpc:
PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal
|
|
- Add pcim_add_mapping_to_legacy_table() and
pcim_remove_mapping_from_legacy_table() helper functions to simplify
devres iomap table (Philipp Stanner)
- Reimplement devres that take a bit mask of BARs in a way that can be used
to map partial BARs as well as entire BARs (Philipp Stanner)
- Deprecate pcim_iomap_table() and pcim_iomap_regions_request_all() in
favor of pcim_* request plus pcim_* mapping (Philipp Stanner)
- Add pcim_request_region(), a managed interface to request a single BAR
(Philipp Stanner)
- Use the existing pci_is_enabled() interface to replace the struct
devres.enabled bit (Philipp Stanner)
- Move the struct pci_devres.pinned bit to struct pci_dev (Philipp Stanner)
- Reimplement pcim_set_mwi() so it uses its own devres cleanup callback
instead of a special-purpose bit in struct pci_devres (Philipp Stanner)
- Add pcim_intx(), which is unambiguously managed, unlike pci_intx(), which
is managed if pcim_enable_device() has been called but unmanaged
otherwise (Philipp Stanner)
- Remove pcim_release(), which is no longer needed after previous cleanups
of pcim_set_mwi() and pci_intx() (Philipp Stanner)
- Add pcim_iomap_range(), a managed interface to map part of a BAR (Philipp
Stanner)
- Fix vboxvideo leak by using the new pcim_iomap_range() instead of the
unmanaged pci_iomap_range() (Philipp Stanner)
* pci/devres:
drm/vboxvideo: fix mapping leaks
PCI: Add managed pcim_iomap_range()
PCI: Remove legacy pcim_release()
PCI: Add managed pcim_intx()
PCI: Give pcim_set_mwi() its own devres cleanup callback
PCI: Move struct pci_devres.pinned bit to struct pci_dev
PCI: Remove struct pci_devres.enabled status bit
PCI: Document hybrid devres hazards
PCI: Add managed pcim_request_region()
PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()
PCI: Add managed partial-BAR request and map infrastructure
PCI: Add devres helpers for iomap table
PCI: Add and use devres helper for bit masks
|
|
PCIe ACS settings control the level of isolation and the possible P2P paths
between devices. With greater isolation the kernel will create smaller
iommu_groups and with less isolation there is more HW that can achieve P2P
transfers. From a virtualization perspective all devices in the same
iommu_group must be assigned to the same VM as they lack security
isolation.
There is no way for the kernel to automatically know the correct ACS
settings for any given system and workload. Existing command line options
(e.g., disable_acs_redir) allow only for large scale change, disabling all
isolation, but this is not sufficient for more complex cases.
Add a kernel command-line option 'config_acs' to directly control all the
ACS bits for specific devices, which allows the operator to setup the right
level of isolation to achieve the desired P2P configuration. The
definition is future proof; when new ACS bits are added to the spec the
open syntax can be extended.
ACS needs to be setup early in the kernel boot as the ACS settings affect
how iommu_groups are formed. iommu_group formation is a one time event
during initial device discovery, so changing ACS bits after kernel boot can
result in an inaccurate view of the iommu_groups compared to the current
isolation configuration.
ACS applies to PCIe Downstream Ports and multi-function devices. The
default ACS settings are strict and deny any direct traffic between two
functions. This results in the smallest iommu_group the HW can support.
Frequently these values result in slow or non-working P2PDMA.
ACS offers a range of security choices controlling how traffic is
allowed to go directly between two devices. Some popular choices:
- Full prevention
- Translated requests can be direct, with various options
- Asymmetric direct traffic, A can reach B but not the reverse
- All traffic can be direct
Along with some other less common ones for special topologies.
The intention is that this option would be used with expert knowledge of
the HW capability and workload to achieve the desired configuration.
Link: https://lore.kernel.org/r/20240625153150.159310-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[bhelgaas: add example, tidy printk formats]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
One of the true positives that the cfg_access_lock lockdep effort
identified is this sequence:
WARNING: CPU: 14 PID: 1 at drivers/pci/pci.c:4886 pci_bridge_secondary_bus_reset+0x5d/0x70
RIP: 0010:pci_bridge_secondary_bus_reset+0x5d/0x70
Call Trace:
<TASK>
? __warn+0x8c/0x190
? pci_bridge_secondary_bus_reset+0x5d/0x70
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? pci_bridge_secondary_bus_reset+0x5d/0x70
pci_reset_bus+0x1d8/0x270
vmd_probe+0x778/0xa10
pci_device_probe+0x95/0x120
Where pci_reset_bus() users are triggering unlocked secondary bus resets.
Ironically pci_bus_reset(), several calls down from pci_reset_bus(), uses
pci_bus_lock() before issuing the reset which locks everything *but* the
bridge itself.
For the same motivation as adding:
bridge = pci_upstream_bridge(dev);
if (bridge)
pci_dev_lock(bridge);
to pci_reset_function() for the "bus" and "cxl_bus" reset cases, add
pci_dev_lock() for @bus->self to pci_bus_lock().
Link: https://lore.kernel.org/r/171711747501.1628941.15217746952476635316.stgit@dwillia2-xfh.jf.intel.com
Reported-by: Imre Deak <imre.deak@intel.com>
Closes: http://lore.kernel.org/r/6657833b3b5ae_14984b29437@dwillia2-xfh.jf.intel.com.notmuch
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
[bhelgaas: squash in recursive locking deadlock fix from Keith Busch:
https://lore.kernel.org/r/20240711193650.701834-1-kbusch@meta.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Kalle Valo <kvalo@kernel.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
|
|
pci_intx() is a "hybrid" function, i.e., it is managed if
pcim_enable_device() has been called, but unmanaged otherwise.
Add pcim_intx(), which is always managed, and implement pci_intx() using
it.
Remove the now-unused struct pci_devres.orig_intx and .restore_intx and
find_pci_dr().
Link: https://lore.kernel.org/r/20240613115032.29098-11-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
[kwilczynski: squashed in
https://lore.kernel.org/r/426645d40776198e0fcc942f4a6cac4433c7a9aa.camel@redhat.com
to fix problem reported and tested by Ashish Kalra <Ashish.Kalra@amd.com>:
https://lore.kernel.org/r/20240708214656.4721-1-Ashish.Kalra@amd.com
https://lore.kernel.org/r/8c4634e9-4f02-4c54-9c89-d75e2f4bf026@amd.com/]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The struct pci_devres has a separate boolean to track whether a device is
enabled. That, however, can easily be tracked in an agnostic manner through
the function pci_is_enabled().
Using it allows for simplifying the PCI devres implementation.
Replace the separate 'enabled' status bit from struct pci_devres with
calls to pci_is_enabled() at the appropriate places.
Link: https://lore.kernel.org/r/20240613115032.29098-8-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
These functions:
pci_request_region()
pci_request_regions()
pci_request_regions_exclusive()
pci_request_selected_regions()
pci_request_selected_regions_exclusive()
pci_intx()
are "hybrid" functions that are managed if pcim_enable_device() has been
called, but unmanaged otherwise.
This is confusing and has already caused a bug (in 8558de401b5f
("drm/vboxvideo: use managed pci functions")) because users believe all PCI
functions, such as pci_iomap_range(), can become managed that way, which is
not the case.
Add comments to the relevant functions' docstrings that warn users about
this behavior.
Link: https://lore.kernel.org/r/20240613115032.29098-7-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
These existing functions:
pci_request_region()
pci_request_selected_regions()
pci_request_selected_regions_exclusive()
are "hybrid" functions built on __pci_request_region() and are managed if
pcim_enable_device() has been called, but unmanaged otherwise.
Add these new functions:
pcim_request_region()
pcim_request_region_exclusive()
These are *always* managed and use the new pcim_addr_devres tracking
infrastructure instead of find_pci_dr() and struct pci_devres.region_mask.
Implement the hybrid functions using the new "pure" functions and remove
struct pci_devres.region_mask, which is no longer needed.
Link: https://lore.kernel.org/r/20240613115032.29098-6-pstanner@redhat.com
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The pcim_iomap_devres table tracks entire-BAR mappings, so we can't use it
to build a managed version of pci_iomap_range(), which maps partial BARs.
Add struct pcim_addr_devres, which can track request and mapping of both
entire BARs and partial BARs.
Add the following internal devres functions based on struct
pcim_addr_devres:
pcim_iomap_region() # request & map entire BAR
pcim_iounmap_region() # unmap & release entire BAR
pcim_request_region() # request entire BAR
pcim_release_region() # release entire BAR
pcim_request_all_regions() # request all entire BARs
pcim_release_all_regions() # rel |
