| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 9cc742078c9a90cdd4cf131e9f760e6965df9048 upstream.
This interface will be used by PCI host drivers for PIO translation,
export it to support compiling those drivers as kernel modules.
Link: https://lore.kernel.org/r/20210420061723.989-3-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64f160e19e9264a7f6d89c516baae1473b6f8359 upstream.
In commit 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window
configuration") was removed aardvark PCIe outbound window configuration and
commit description said that was recommended solution by HW designers.
But that commit completely removed support for configuring PCIe IO
resources without removing PCIe IO 'ranges' from DTS files. After that
commit PCIe IO space started to be treated as PCIe MEM space and accessing
it just caused kernel crash.
Moreover implementation of PCIe outbound windows prior that commit was
incorrect. It completely ignored offset between CPU address and PCIe bus
address and expected that in DTS is CPU address always same as PCIe bus
address without doing any checks. Also it completely ignored size of every
PCIe resource specified in 'ranges' DTS property and expected that every
PCIe resource has size 128 MB (also for PCIe IO range). Again without any
check. Apparently none of PCIe resource has in DTS specified size of 128
MB. So it was completely broken and thanks to how aardvark mask works,
configuration was completely ignored.
This patch reverts back support for PCIe outbound window configuration but
implementation is a new without issues mentioned above. PCIe outbound
window is required when DTS specify in 'ranges' property non-zero offset
between CPU and PCIe address space. To address recommendation by HW
designers as specified in commit description of 6df6ba974a55, set default
outbound parameters as PCIe MEM access without translation and therefore
for this PCIe 'ranges' it is not needed to configure PCIe outbound window.
For PCIe IO space is needed to configure aardvark PCIe outbound window.
This patch fixes kernel crash when trying to access PCIe IO space.
Link: https://lore.kernel.org/r/20210624215546.4015-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # 6df6ba974a55 ("PCI: aardvark: Remove PCIe outbound window configuration")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de0a01f5296651d3a539f2d23d0db8f359483696 upstream.
Enable PCIe reference clock. There is no remove function that's why
this should be enough for simple operation.
Normally this clock is enabled by default by firmware but there are
usecases where this clock should be enabled by driver itself.
It is also good that PCIe clock is recorded in a clock framework.
Link: https://lore.kernel.org/r/ee6997a08fab582b1c6de05f8be184f3fe8d5357.1624618100.git.michal.simek@xilinx.com
Fixes: ab597d35ef11 ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8bd29bd49c4156ea0ec5a97812333e2aeef44e7 upstream.
The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.
If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.
When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno. But after
e4585da22ad0 ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.
Userspace may rely on the ~0 data to detect errors, but after e4585da22ad0,
that would not detect CAP_SYS_ADMIN errors.
Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.
[bhelgaas: commit log, fold in Nathan's fix
https://lore.kernel.org/r/20210803200836.500658-1-nathan@kernel.org]
Fixes: e4585da22ad0 ("pci syscall.c: Switch to refcounting API")
Link: https://lore.kernel.org/r/20210729233755.1509616-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b12d93e9958e028856cbcb061b6e64728ca07755 upstream.
The ASMedia ASM1062 SATA controller advertises Max_Payload_Size_Supported
of 512, but in fact it cannot handle incoming TLPs with payload size of
512.
We discovered this issue on PCIe controllers capable of MPS = 512 (Aardvark
and DesignWare), where the issue presents itself as an External Abort.
Bjorn Helgaas says:
Probably ASM1062 reports a Malformed TLP error when it receives a data
payload of 512 bytes, and Aardvark, DesignWare, etc convert this to an
arm64 External Abort. [1]
To avoid this problem, limit the ASM1062 Max Payload Size Supported to 256
bytes, so we set the Max Payload Size of devices that may send TLPs to the
ASM1062 to 256 or less.
[1] https://lore.kernel.org/linux-pci/20210601170907.GA1949035@bjorn-Precision-5520/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212695
Link: https://lore.kernel.org/r/20210624171418.27194-2-kabel@kernel.org
Reported-by: Rötti <espressobinboardarmbiantempmailaddress@posteo.de>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00823dcbdd415c868390feaca16f0265101efab4 upstream.
Previously we assumed that all Root Ports and Switch Downstream Ports
supported Link Bandwidth Notification. Per spec, this is only required
for Ports supporting Links wider than x1 and/or multiple Link speeds
(PCIe r5.0, sec 7.5.3.6).
Because we assumed all Ports supported it, we tried to set up a Bandwidth
Notification IRQ, which failed for devices that don't support IRQs at all,
which meant pcieport didn't attach to the Port at all.
Check the Link Bandwidth Notification Capability bit and enable the service
only when the Port supports it.
[bhelgaas: commit log]
Fixes: e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/r/20210512213314.7778-1-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1a519dc7a73c977547d8b5108d98c6e769c89f4b upstream.
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d36123 ("PCI/MSI: Mask all unused MSI-X entries")
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e00392a895c95c6d12d42158236c8862a2f43f2 ]
PME signaling is only enabled by __pci_enable_wake() if the target
device can signal PME from the given target power state (to avoid
pointless reconfiguration of the device), but if the hierarchy above
the device goes into D3cold, the device itself will end up in D3cold
too, so if it can signal PME from D3cold, it should be enabled to
do so in __pci_enable_wake().
[Note that if the device does not end up in D3cold and it cannot
signal PME from the original target power state, it will not signal
PME, so in that case the behavior does not change.]
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 5bcc2fb4e815 ("PCI PM: Simplify PCI wake-up code")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da9f2150684ea684a7ddd6d7f0e38b2bdf43dcd8 ]
It is inconsistent to return PCI_D0 from pci_target_state() instead
of the original target state if 'wakeup' is true and the device
cannot signal PME from D0.
This only happens when the device cannot signal PME from the original
target state and any shallower power states (including D0) and that
case is effectively equivalent to the one in which PME singaling is
not supported at all. Since the original target state is returned in
the latter case, make the function do that in the former one too.
Link: https://lore.kernel.org/linux-pm/3149540.aeNJFYEL58@kreacher/
Fixes: 666ff6f83e1d ("PCI/PM: Avoid using device_may_wakeup() for runtime PM")
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b8da302e2955fe4d41eb9d48199242674d77dbe0 upstream.
pci_device_add() calls HEADER fixups after pci_configure_device(), which
configures Max Payload Size.
Convert MPS-related fixups to EARLY fixups so pci_configure_mps() takes
them into account.
Fixes: 27d868b5e6cfa ("PCI: Set MPS to match upstream bridge")
Link: https://lore.kernel.org/r/20210624171418.27194-1-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e0bff43220925b7e527f9d3bc9f5c624177c959e ]
The Renoir XHCI controller apparently doesn't resume reliably with the
standard D3hot-to-D0 delay. Increase it to 20ms.
[Alex: I talked to the AMD USB hardware team and the AMD Windows team and
they are not aware of any HW errata or specific issues. The HW works fine
in Windows. I was told Windows uses a rather generous default delay of
100ms for PCI state transitions.]
Link: https://lore.kernel.org/r/20210722025858.220064-1-alexander.deucher@amd.com
Signed-off-by: Marcin Bachry <hegel666@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Prike Liang <prike.liang@amd.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 77e89afc25f30abd56e76a809ee2884d7c1b63ce upstream.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d28d4ad2a1aef27458b3383725bb179beb8d015c upstream.
No point in using the raw write function from shutdown. Preparatory change
to introduce proper serialization for the msi_desc::masked cache.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.674391354@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 689e6b5351573c38ccf92a0dd8b3e2c2241e4aff upstream.
The comments about preserving the cached state in pci_msi[x]_shutdown() are
misleading as the MSI descriptors are freed right after those functions
return. So there is nothing to restore. Preparatory change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.621609423@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 361fd37397f77578735907341579397d5bed0a2d upstream.
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db02f ("PCI MSI: Unmask MSI if setup failed")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9255a7cb51754e8d2645b65dd31805e282b4f3e upstream.
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da181dc974ad667579baece33c2c8d2d1e4558d5 upstream.
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Reported-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d5ec3d3612396dc6d4b76366d20ab9fc06f399f upstream.
When MSI-X is enabled the ordering of calls is:
msix_map_region();
msix_setup_entries();
pci_msi_setup_msi_irqs();
msix_program_entries();
This has a few interesting issues:
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 438553958ba19296663c6d6583d208dfb6792830 upstream.
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e105 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8946a53e2a698c148b3b3ed732f43c7747fbeb6 upstream
Observed unexpected GPU hang during runpm stress test on 0x7341 rev 0x00.
Further debugging shows broken ATS is related.
Disable ATS on this part. Similar issues on other devices:
a2da5d8cc0b0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
45beb31d3afb ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
5e89cd303e3a ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20210602021255.939090-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f67092eff2bd40650aad54a1a1910160f41d864a ]
tegra_pcie_ep_raise_msi_irq() shifted a signed 32-bit value left by 31
bits. The behavior of this is implementation-defined.
Replace the shift by BIT(), which is well-defined.
Found by cppcheck:
$ cppcheck --enable=all drivers/pci/controller/dwc/pcie-tegra194.c
Checking drivers/pci/controller/dwc/pcie-tegra194.c ...
drivers/pci/controller/dwc/pcie-tegra194.c:1829:23: portability: Shifting signed 32-bit value by 31 bits is implementation-defined behaviour. See condition at line 1826. [shiftTooManyBitsSigned]
appl_writel(pcie, (1 << irq), APPL_MSI_CTRL_1);
^
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210618160219.303092-1-jonathanh@nvidia.com
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 655832d12f2251e04031294f547c86935a0a126d ]
The legacy PCI interrupt lines need to be enabled using PCIE_APP_IRNEN bits
13 (INTA), 14 (INTB), 15 (INTC) and 16 (INTD). The old code however was
taking (for example) "13" as raw value instead of taking BIT(13). Define
the legacy PCI interrupt bits using the BIT() macro and then use these in
PCIE_APP_IRN_INT.
Link: https://lore.kernel.org/r/20210106135540.48420-1-martin.blumenstingl@googlemail.com
Fixes: ed22aaaede44 ("PCI: dwc: intel: PCIe RC controller driver")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rahul Tanwar <rtanwar@maxlinear.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2dc0a201d0f59e6818ef443609f0850a32910844 ]
The interrupt affinity scheme used by this driver is incompatible with
multi-MSI as it implies moving the doorbell address to that of another MSI
group. This isn't possible for multi-MSI, as all the MSIs must have the
same doorbell address. As such it is restricted to systems with a single
CPU.
Link: https://lore.kernel.org/r/20210622152630.40842-2-sbodomerle@gmail.com
Fixes: fc54bae28818 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e673d697b9a234fc3544ac240e173cef8c82b349 ]
Commit fc54bae28818 ("PCI: iproc: Allow allocation of multiple MSIs")
introduced multi-MSI support with a broken allocation mechanism (it failed
to reserve the proper number of bits from the inner domain). Natural
alignment of the base vector number was also not guaranteed.
Link: https://lore.kernel.org/r/20210622152630.40842-1-sbodomerle@gmail.com
Fixes: fc54bae28818 ("PCI: iproc: Allow allocation of multiple MSIs")
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sandor Bodo-Merle <sbodomerle@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdcdaa13ad96f1a530711c29e6d4b8311eff767c ]
"utf16s_to_utf8s(..., buf, PAGE_SIZE)" puts up to PAGE_SIZE bytes into
"buf" and returns the number of bytes it actually put there. If it wrote
PAGE_SIZE bytes, the newline added by dsm_label_utf16s_to_utf8s() would
overrun "buf".
Reduce the size available for utf16s_to_utf8s() to use so there is always
space for the newline.
[bhelgaas: reorder patch in series, commit log]
Fixes: 6058989bad05 ("PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs")
Link: https://lore.kernel.org/r/20210603000112.703037-7-kw@linux.com
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3cf5f7ab230e2b886e493c7a8449ed50e29d2b98 ]
An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.
rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller. If either is called before the clocks
are turned on, the register reads fail and the machine hangs.
Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.
Register IRQ handlers after their data structures are initialized and
clocks are enabled.
Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered. An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7bf475a4614a9722b9b989e53184a02596cf16d1 ]
Add missing MODULE_DEVICE_TABLE definition so we generate correct modalias
for automatic loading of this driver when it is built as a module.
Link: https://lore.kernel.org/r/1620792422-16535-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a97396c6eb13f65bea894dbe7739b2e883d40a3e ]
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3ec0c3ec2d92c09465534a1ff9c6f9d9506ffef6 ]
In order to use upstream_bridge_distance_warn() from a dma_map function, it
must not sleep. However, pci_get_slot() takes the pci_bus_sem so it might
sleep.
In order to avoid this, try to get the host bridge's device from the first
element in the device list. It should be impossible for the host bridge's
device to go away while references are held on child devices, so the first
element should not be able to change and, thus, this should be safe.
Introduce a static function called pci_host_bridge_dev() to obtain the host
bridge's root device.
Link: https://lore.kernel.org/r/20210610160609.28447-7-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 94d22763207ac6633612b8d8e0ca4fba0f7aa139 ]
On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().
This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.
Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.
Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5be967d5016ac5ffb9c4d0df51b48441ee4d5ed1 ]
PCI_IOSIZE is defined in mach-loongson64/spaces.h, so change the name
of the PCI_* macros in pci-ftpci100.c to use FTPCI_* so that they are
more localized and won't conflict with other drivers or arches.
../drivers/pci/controller/pci-ftpci100.c:37: warning: "PCI_IOSIZE" redefined
37 | #define PCI_IOSIZE 0x00
|
In file included from ../arch/mips/include/asm/addrspace.h:13,
... from ../drivers/pci/controller/pci-ftpci100.c:15:
arch/mips/include/asm/mach-loongson64/spaces.h:11: note: this is the location of the previous definition
11 | #define PCI_IOSIZE SZ_16M
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210517234117.3660-1-rdunlap@infradead.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7f71a409fe3d9358da07c77f15bb5b7960f12253 upstream.
Marvell Armada 3700 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in aardvark driver for both PCI vendor id and PCI
subsystem vendor id.
This change affects and fixes PCI vendor id of emulated PCIe root bridge.
After this change emulated PCIe root bridge has correct vendor id.
Link: https://lore.kernel.org/r/20210624222621.4776-5-pali@kernel.org
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8ceeac307a79f68c0d0c72d6e48b82fa424204ec upstream.
PIO_NON_POSTED_REQ for PIO_STAT register is incorrectly defined. Bit 10 in
register PIO_STAT indicates the response is to a non-posted request.
Link: https://lore.kernel.org/r/20210624213345.3617-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4694ae373dc2114f9a82f6ae15737e65af0c6dea upstream.
On Macbook 2013, resuming from suspend-to-idle or standby resulted in the
external monitor no longer being detected, a stacktrace, and errors like
this in dmesg:
pcieport 0000:06:00.0: can't change power state from D3hot to D0 (config space inaccessible)
The reason is that we know how to turn power to the Thunderbolt controller
*off* via the SXIO/SXFP/SXLF methods, but we don't know how to turn power
back on. We have to rely on firmware to turn the power back on.
When going to the "suspend-to-idle" or "standby" system sleep states,
firmware is not involved either on the suspend side or the resume side, so
we can't use SXIO/SXFP/SXLF to turn the power off.
Skip SXIO/SXFP/SXLF when firmware isn't involved in suspend, e.g., when
we're going to the "suspend-to-idle" or "standby" system sleep states.
Fixes: 1df5172c5c25 ("PCI: Suspend/resume quirks for Apple thunderbolt")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212767
Link: https://lore.kernel.org/r/20210520235501.917397-1-Hi-Angel@yandex.ru
Signed-off-by: Konstantin Kharlamov <Hi-Angel@yandex.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7d815f4afa87f2032b650ae1bba7534b550a6b8b ]
Add check for hv_is_hyperv_initialized() at the top of
init_hv_pci_drv(), so if the pci-hyperv driver is force-loaded on non
Hyper-V platforms, the init_hv_pci_drv() will exit immediately, without
any side effects, like assignments to hvpci_block_ops, etc.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reported-and-tested-by: Mohammad Alqayeem <mohammad.alqyeem@nutanix.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/1621984653-1210-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d6035f9bf4ea12776322746a216e856dfe46698 ]
Revert commit 4514d991d992 ("PCI: PM: Do not read power state in
pci_enable_device_flags()") that is reported to cause PCI device
initialization issues on some systems.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213481
Link: https://lore.kernel.org/linux-acpi/YNDoGICcg0V8HhpQ@eldamar.lan
Reported-by: Michael <phyre@rogers.com>
Reported-by: Salvatore Bonaccorso <carnil@debian.org>
Fixes: 4514d991d992 ("PCI: PM: Do not read power state in pci_enable_device_flags()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ce00322c2365e1f7b0312f2f493539c833465d97 upstream.
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
[bhelgaas: commit log]
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr
Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com
Signed-off-by: Chiqijun <chiqijun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db2f77e2bd99dbd2fb23ddde58f0fae392fe3338 upstream.
The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1621645997-16251-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhe |
