| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit c22533c66ccae10511ad6a7afc34bb26c47577e3 ]
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
Fixes: beb4641a787d ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260211175540.105677-2-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 468711a40d5dfc01bf0a24c1981246a2c93ac405 ]
Endpoint drivers use dw_pcie_ep_raise_msi_irq() to raise MSI interrupts to
the host. After 8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU
mapping"), dw_pcie_ep_raise_msi_irq() caches the Message Address from the
MSI Capability in ep->msi_msg_addr. But that Message Address is controlled
by the host, and it may change. For example, if:
- firmware on the host configures the Message Address and triggers an
MSI,
- a driver on the Endpoint raises the MSI via dw_pcie_ep_raise_msi_irq(),
which caches the Message Address,
- a kernel on the host reconfigures the Message Address and the host
kernel driver triggers another MSI,
dw_pcie_ep_raise_msi_irq() notices that the Message Address no longer
matches the cached ep->msi_msg_addr, warns about it, and returns error
instead of raising the MSI. The host kernel may hang because it never
receives the MSI.
This was seen with the nvmet_pci_epf_driver: the host UEFI performs NVMe
commands, e.g. Identify Controller to get the name of the controller,
nvmet-pci-epf posts the completion queue entry and raises an IRQ using
dw_pcie_ep_raise_msi_irq(). When the host boots Linux, we see a
WARN_ON_ONCE() from dw_pcie_ep_raise_msi_irq(), and the host kernel hangs
because the nvme driver never gets an IRQ.
Remove the warning when dw_pcie_ep_raise_msi_irq() notices that Message
Address has changed, remap using the new address, and update the
ep->msi_msg_addr cache.
Fixes: 8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Tested-by: Koichiro Den <den@valinux.co.jp>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20260210181225.3926165-2-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9368d1ee62829b08aa31836b3ca003803caf0b72 ]
Commit a4e772898f8b ("PCI: Add missing bridge lock to pci_bus_lock()")
delegates the bridge device's pci_dev_trylock() to pci_bus_trylock() in
pci_slot_trylock(), but it forgets to remove the corresponding
pci_dev_unlock() when pci_bus_trylock() fails.
Before a4e772898f8b, the code did:
if (!pci_dev_trylock(dev)) /* <- lock bridge device */
goto unlock;
if (dev->subordinate) {
if (!pci_bus_trylock(dev->subordinate)) {
pci_dev_unlock(dev); /* <- unlock bridge device */
goto unlock;
}
}
After a4e772898f8b the bridge-device lock is no longer taken, but the
pci_dev_unlock(dev) on the failure path was left in place, leading to the
bug.
This yields one of two errors:
1. A warning that the lock is being unlocked when no one holds it.
2. An incorrect unlock of a lock that belongs to another thread.
Fix it by removing the now-redundant pci_dev_unlock(dev) on the failure
path.
[Same patch later posted by Keith at
https://patch.msgid.link/20260116184150.3013258-1-kbusch@meta.com]
Fixes: a4e772898f8b ("PCI: Add missing bridge lock to pci_bus_lock()")
Signed-off-by: Jinhui Guo <guojinhui.liam@bytedance.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251212145528.2555-1-guojinhui.liam@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2ecc1bf14e2fdaff78bd1b8e7ed3dba336a3fad5 ]
The commit 8278c6914306 ("PCI: Preserve bridge window resource type flags")
changed bridge window resource behavior such that flags are no longer zero
if the bridge window is not valid or is disabled (mainly to preserve the
type flags for later use). If a bridge window has its limit smaller than
base address, pci_read_bridge_*() sets both IORESOURCE_UNSET and
IORESOURCE_DISABLED to indicate the bridge window exists but is not valid
with the current base and limit configuration.
The code in pci_claim_bridge_resources() still depends on the old behavior
of checking validity of the bridge window solely based on !r->flags,
whereas after 8278c6914306, also IORESOURCE_DISABLED may indicate bridge
window addresses are not valid.
While pci_claim_resource() does check IORESOURCE_UNSET,
pci_claim_bridge_resource() attempts to clip the resource if
pci_claim_resource() fails, which is not correct for bridge window
resources that are not valid. As pci_bus_clip_resource() performs clipping
regardless of flags and then clears IORESOURCE_UNSET, it should not be
called unless the resource is valid.
The problem is visible in this log:
pci 0000:20:00.0: PCI bridge to [bus 21]
pci 0000:20:00.0: bridge window [io size 0x0000 disabled]: can't claim; no address assigned
pci 0000:20:00.0: [io 0x0000-0xffffffffffffffff disabled] clipped to [io 0x0000-0xffff disabled]
Add IORESOURCE_DISABLED check in pci_claim_bridge_resources() to only
claim bridge windows that appear to have a valid configuration.
Fixes: 8278c6914306 ("PCI: Preserve bridge window resource type flags")
Reported-by: Sizhe Liu <liusizhe5@huawei.com>
Link: https://lore.kernel.org/all/20260203023545.2753811-1-liusizhe5@huawei.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/4d9228d6-a230-6ddf-e300-fbf42d523863@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58fbf08935d9c4396417e5887df89a4e681fa7e3 ]
When dw_pcie_iatu_setup() configures outbound address translation for both
type PCIE_ATU_TYPE_MEM and PCIE_ATU_TYPE_IO, the iATU index to use is
incremented before calling dw_pcie_prog_outbound_atu().
However for msg_atu_index, the index is not incremented before use,
causing the iATU index to be the same as the last configured iATU index,
which means that it will incorrectly use the same iATU index that is
already in use, breaking outbound address translation.
In total there are three problems with this code:
-It assigns msg_atu_index the same index that was used for the last
outbound address translation window, rather than incrementing the index
before assignment.
-The index should only be incremented (and msg_atu_index assigned) if the
use_atu_msg feature is actually requested/in use (pp->use_atu_msg is set).
-If the use_atu_msg feature is requested/in use, and there are no outbound
iATUs available, the code should return an error, as otherwise when this
this feature is used, it will use an iATU index that is out of bounds.
Fixes: e1a4ec1a9520 ("PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system suspend")
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hans Zhang <zhanghuabing@ecosda.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260127151038.1484881-6-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a5338e365c4559d7b4d7356116b0eb95b12e08d5 ]
Commit 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking when
enabling/disabling SR-IOV") tried to fix a race between the VF removal
inside sriov_del_vfs() and concurrent hot unplug by taking the PCI
rescan/remove lock in sriov_del_vfs(). Similarly the PCI rescan/remove lock
was also taken in sriov_add_vfs() to protect addition of VFs.
This approach however causes deadlock on trying to remove PFs with SR-IOV
enabled because PFs disable SR-IOV during removal and this removal happens
under the PCI rescan/remove lock. So the original fix had to be reverted.
Instead of taking the PCI rescan/remove lock in sriov_add_vfs() and
sriov_del_vfs(), fix the race that occurs with SR-IOV enable and disable vs
hotplug higher up in the callchain by taking the lock in
sriov_numvfs_store() before calling into the driver's sriov_configure()
callback.
Fixes: 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV")
Reported-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251216-revert_sriov_lock-v3-2-dac4925a7621@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2fa119c0e5e528453ebae9e70740e8d2d8c0ed5a ]
This reverts commit 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking
when enabling/disabling SR-IOV"), which causes a deadlock by recursively
taking pci_rescan_remove_lock when sriov_del_vfs() is called as part of
pci_stop_and_remove_bus_device(). For example with the following sequence
of commands:
$ echo <NUM> > /sys/bus/pci/devices/<pf>/sriov_numvfs
$ echo 1 > /sys/bus/pci/devices/<pf>/remove
A trimmed trace of the deadlock on a mlx5 device is as below:
zsh/5715 is trying to acquire lock:
000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: sriov_disable+0x34/0x140
but task is already holding lock:
000002597926ef50 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_stop_and_remove_bus_device_locked+0x24/0x80
...
Call Trace:
[<00000259778c4f90>] dump_stack_lvl+0xc0/0x110
[<00000259779c844e>] print_deadlock_bug+0x31e/0x330
[<00000259779c1908>] __lock_acquire+0x16c8/0x32f0
[<00000259779bffac>] lock_acquire+0x14c/0x350
[<00000259789643a6>] __mutex_lock_common+0xe6/0x1520
[<000002597896413c>] mutex_lock_nested+0x3c/0x50
[<00000259784a07e4>] sriov_disable+0x34/0x140
[<00000258f7d6dd80>] mlx5_sriov_disable+0x50/0x80 [mlx5_core]
[<00000258f7d5745e>] remove_one+0x5e/0xf0 [mlx5_core]
[<00000259784857fc>] pci_device_remove+0x3c/0xa0
[<000002597851012e>] device_release_driver_internal+0x18e/0x280
[<000002597847ae22>] pci_stop_bus_device+0x82/0xa0
[<000002597847afce>] pci_stop_and_remove_bus_device_locked+0x5e/0x80
[<00000259784972c2>] remove_store+0x72/0x90
[<0000025977e6661a>] kernfs_fop_write_iter+0x15a/0x200
[<0000025977d7241c>] vfs_write+0x24c/0x300
[<0000025977d72696>] ksys_write+0x86/0x110
[<000002597895b61c>] __do_syscall+0x14c/0x400
[<000002597896e0ee>] system_call+0x6e/0x90
This alone is not a complete fix as it restores the issue the cited commit
tried to solve. A new fix will be provided as a follow on.
Fixes: 05703271c3cd ("PCI/IOV: Add PCI rescan-remove locking when enabling/disabling SR-IOV")
Reported-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Acked-by: Gerd Bayer <gbayer@linux.ibm.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251216-revert_sriov_lock-v3-1-dac4925a7621@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7e90360e6d4599795b6f4e094e20d0bdf3b2615f ]
pbus_size_mem() has two alignments, one for required resources in min_align
and another in add_align that takes account optional resources.
The add_align is applied to the bridge window through the realloc_head
list. It can happen, however, that add_align is larger than min_align but
calculated size1 and size0 are equal due to extra tailroom (e.g., hotplug
reservation, tail alignment), and therefore no entry is created to the
realloc_head list. Without the bridge appearing in the realloc head,
add_align is lost when pbus_size_mem() returns.
The problem is visible in this log for 0000:05:00.0 which lacks
add_size ... add_align ... line that would indicate it was added into
the realloc_head list:
pci 0000:05:00.0: PCI bridge to [bus 06-16]
...
pci 0000:06:00.0: bridge window [mem 0x00100000-0x001fffff] to [bus 07] requires relaxed alignment rules
pci 0000:06:06.0: bridge window [mem 0x00100000-0x001fffff] to [bus 0a] requires relaxed alignment rules
pci 0000:06:07.0: bridge window [mem 0x00100000-0x003fffff] to [bus 0b] requires relaxed alignment rules
pci 0000:06:08.0: bridge window [mem 0x00800000-0x00ffffff 64bit pref] to [bus 0c-14] requires relaxed alignment rules
pci 0000:06:08.0: bridge window [mem 0x01000000-0x057fffff] to [bus 0c-14] requires relaxed alignment rules
pci 0000:06:08.0: bridge window [mem 0x01000000-0x057fffff] to [bus 0c-14] requires relaxed alignment rules
pci 0000:06:08.0: bridge window [mem 0x01000000-0x057fffff] to [bus 0c-14] add_size 100000 add_align 1000000
pci 0000:06:0c.0: bridge window [mem 0x00100000-0x001fffff] to [bus 15] requires relaxed alignment rules
pci 0000:06:0d.0: bridge window [mem 0x00100000-0x001fffff] to [bus 16] requires relaxed alignment rules
pci 0000:06:0d.0: bridge window [mem 0x00100000-0x001fffff] to [bus 16] requires relaxed alignment rules
pci 0000:05:00.0: bridge window [mem 0xd4800000-0xd97fffff]: assigned
pci 0000:05:00.0: bridge window [mem 0x1060000000-0x10607fffff 64bit pref]: assigned
pci 0000:06:08.0: bridge window [mem size 0x04900000]: can't assign; no space
pci 0000:06:08.0: bridge window [mem size 0x04900000]: failed to assign
While this bug itself seems old, it has likely become more visible after
the relaxed tail alignment that does not grossly overestimate the size
needed for the bridge window.
Make sure add_align > min_align too results in adding an entry into the
realloc head list. In addition, add handling to the cases where add_size is
zero while only alignment differs.
Fixes: d74b9027a4da ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Reported-by: Malte Schröder <malte+lkml@tnxip.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Malte Schröder <malte+lkml@tnxip.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251219174036.16738-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
pci_{primary/secondary}_epc_epf_unlink() functions
[ Upstream commit 8754dd7639ab0fd68c3ab9d91c7bdecc3e5740a8 ]
struct configfs_item_operations callbacks are defined like the following:
int (*allow_link)(struct config_item *src, struct config_item *target);
void (*drop_link)(struct config_item *src, struct config_item *target);
While pci_primary_epc_epf_link() and pci_secondary_epc_epf_link() specify
the parameters in the correct order, pci_primary_epc_epf_unlink() and
pci_secondary_epc_epf_unlink() specify the parameters in the wrong order,
leading to the below kernel crash when using the unlink command in
configfs:
Unable to handle kernel paging request at virtual address 0000000300000857
Mem abort info:
...
pc : string+0x54/0x14c
lr : vsnprintf+0x280/0x6e8
...
string+0x54/0x14c
vsnprintf+0x280/0x6e8
vprintk_default+0x38/0x4c
vprintk+0xc4/0xe0
pci_epf_unbind+0xdc/0x108
configfs_unlink+0xe0/0x208+0x44/0x74
vfs_unlink+0x120/0x29c
__arm64_sys_unlinkat+0x3c/0x90
invoke_syscall+0x48/0x134
do_el0_svc+0x1c/0x30prop.0+0xd0/0xf0
Fixes: e85a2d783762 ("PCI: endpoint: Add support in configfs to associate two EPCs with EPF")
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[mani: cced stable, changed commit message as per https://lore.kernel.org/linux-pci/aV9joi3jF1R6ca02@ryzen]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260108062747.1870669-1-mmaddireddy@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 51c0996dadaea20d73eb0495aeda9cb0422243e8 ]
Previously, it was possible for a PCI device to be runtime-suspended before
it was fully initialized. When that happened, the suspend process could
save invalid device state, for example, before BAR assignment. Restoring
the invalid state during resume may leave the device non-functional.
Prevent runtime suspend for PCI devices until they are fully initialized by
deferring pm_runtime_enable().
More details on how exactly this may occur:
1. PCI device is created by pci_scan_slot() or similar
2. As part of pci_scan_slot(), pci_pm_init() puts the device in D0 and
prevents runtime suspend prevented via pm_runtime_forbid()
3. pci_device_add() adds the underlying 'struct device' via device_add(),
which means user space can allow runtime suspend, e.g.,
echo auto > /sys/bus/pci/devices/.../power/control
4. PCI device receives BAR configuration
(pci_assign_unassigned_bus_resources(), etc.)
5. pci_bus_add_device() applies final fixups, saves device state, and
tries to attach a driver
The device may potentially be suspended between #3 and #5, so this is racy
with user space (udev or similar).
Many PCI devices are enumerated at subsys_initcall time and so will not
race with user space, but devices created later by hotplug or modular
pwrctrl or host controller drivers are susceptible to this race.
More runtime PM details at the first Link: below.
Link: https://lore.kernel.org/all/0e35a4e1-894a-47c1-9528-fc5ffbafd9e2@samsung.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
[bhelgaas: update comments per https://lore.kernel.org/r/CAJZ5v0iBNOmMtqfqEbrYyuK2u+2J2+zZ-iQd1FvyCPjdvU2TJg@mail.gmail.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260122094815.v5.1.I60a53c170a8596661883bd2b4ef475155c7aa72b@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 58a17b2647ba5aac47e3ffafd0a9b92bf4a9bcbe ]
In NXP i.MX6QP and i.MX7D SoCs, LTSSM registers are not accessible once
PME_Turn_Off message is broadcasted to the link. So there is no way to
verify whether the link has entered L2/L3 Ready state or not.
Hence, add a new flag 'dw_pcie_rp::skip_l23_ready' and set it to 'true' for
the above mentioned SoCs. This flag when set, will allow the DWC core to
skip polling for L2/L3 Ready state and just wait for 10ms as recommended in
the PCIe spec r6.0, sec 5.3.3.2.1.
Fixes: a528d1a72597 ("PCI: imx6: Use DWC common suspend resume method")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: renamed flag to skip_l23_ready and reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260114083300.3689672-2-hongxing.zhu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11721c45a8266a9d0c9684153d20e37159465f96 ]
__pci_read_base() sets resource start and end addresses when resource
is larger than 4G but pci_bus_addr_t or resource_size_t are not capable
of representing 64-bit PCI addresses. This creates a problematic
resource that has non-zero flags but the start and end addresses do not
yield to resource size of 0 but 1.
Replace custom resource addresses setup with resource_set_range()
that correctly sets end address as -1 which results in resource_size()
returning 0.
For consistency, also use resource_set_range() in the other branch that
does size based resource setup.
Fixes: 23b13bc76f35 ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: https://lore.kernel.org/all/20251207215359.28895-1-ansuelsmth@gmail.com/T/#m990492684913c5a158ff0e5fc90697d8ad95351b
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: stable@vger.kernel.org
Cc: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20251208145654.5294-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 142d5869f6eec3110adda0ad2d931f5b3c22371d ]
This reverts commit 8d3bf19f1b585a3cc0027f508b64c33484db8d0d.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
So revert the change that skipped dw_pcie_wait_for_link() if the Link up
IRQ was used by a vendor glue driver.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-14-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
'global_irq' interrupt"
[ Upstream commit 9a9793b55854422652ea92625e48277c4651c0fd ]
This reverts commit 4581403f67929d02c197cb187c4e1e811c9e762a.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-13-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
IRQ' is supported"
[ Upstream commit 7ebdefb87942073679e56cfbc5a72e8fc5441bfc ]
This reverts commit ba4a2e2317b9faeca9193ed6d3193ddc3cf2aba3.
Since the Link up IRQ support is going away, revert the MSI logic that got
added for it too.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
[mani: reworded the description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-12-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9ce5b3804436301ab343bc14203a4c14b336d1b ]
This reverts commit 36971d6c5a9a134c15760ae9fd13c6d5f9a36abb.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-11-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 180c3cfe36786d261a55da52a161f9e279b19a6f ]
This reverts commit 0e0b45ab5d770a748487ba0ae8f77d1fb0f0de3e.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-10-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f994bb8f1c94726e0124356ccd31c3c23a8a69f4 ]
Rename rockchip_pcie_get_ltssm() to rockchip_pcie_get_ltssm_reg() and add
rockchip_pcie_get_ltssm() to get_ltssm() callback in order to show the
proper L1 Substates. The PCIE_CLIENT_LTSSM_STATUS[5:0] register returns
the same LTSSM layout as enum dw_pcie_ltssm. So the driver just need to
convey L1 PM Substates by returning the proper value defined in
pcie-designware.h.
cat /sys/kernel/debug/dwc_pcie_a40000000.pcie/ltssm_status
L1_2 (0x142)
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/1765503205-22184-2-git-send-email-shawn.lin@rock-chips.com
Stable-dep-of: 180c3cfe3678 ("Revert "PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 679ec639f29cbdaf36bd79bf3e98240fffa335ee ]
DWC core couldn't distinguish LTSSM state among L1.0, L1.1 and L1.2. But
the vendor glue driver may implement additional logic to convey this
information. So add two pseudo definitions for vendor glue drivers to
translate their internal L1 Substates for debugfs to show.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/1765503205-22184-1-git-send-email-shawn.lin@rock-chips.com
Stable-dep-of: 180c3cfe3678 ("Revert "PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ"")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc6298086bfacaa7003b0bd1da4e4f42b29f7d77 ]
This reverts commit ec9fd499b9c60a187ac8d6414c3c343c77d32e42.
While this fake hotplugging was a nice idea, it has shown that this feature
does not handle PCIe switches correctly:
pci_bus 0004:43: busn_res: can not insert [bus 43-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:43: busn_res: [bus 43-41] end is updated to 43
pci_bus 0004:43: busn_res: can not insert [bus 43] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:00.0: devices behind bridge are unusable because [bus 43] cannot be assigned for them
pci_bus 0004:44: busn_res: can not insert [bus 44-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:44: busn_res: [bus 44-41] end is updated to 44
pci_bus 0004:44: busn_res: can not insert [bus 44] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:02.0: devices behind bridge are unusable because [bus 44] cannot be assigned for them
pci_bus 0004:45: busn_res: can not insert [bus 45-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:45: busn_res: [bus 45-41] end is updated to 45
pci_bus 0004:45: busn_res: can not insert [bus 45] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:06.0: devices behind bridge are unusable because [bus 45] cannot be assigned for them
pci_bus 0004:46: busn_res: can not insert [bus 46-41] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci_bus 0004:46: busn_res: [bus 46-41] end is updated to 46
pci_bus 0004:46: busn_res: can not insert [bus 46] under [bus 42-41] (conflicts with (null) [bus 42-41])
pci 0004:42:0e.0: devices behind bridge are unusable because [bus 46] cannot be assigned for them
pci_bus 0004:42: busn_res: [bus 42-41] end is updated to 46
pci_bus 0004:42: busn_res: can not insert [bus 42-46] under [bus 41] (conflicts with (null) [bus 41])
pci 0004:41:00.0: devices behind bridge are unusable because [bus 42-46] cannot be assigned for them
pcieport 0004:40:00.0: bridge has subordinate 41 but max busn 46
During the initial scan, PCI core doesn't see the switch and since the Root
Port is not hot plug capable, the secondary bus number gets assigned as the
subordinate bus number. This means, the PCI core assumes that only one bus
will appear behind the Root Port since the Root Port is not hot plug
capable.
This works perfectly fine for PCIe endpoints connected to the Root Port,
since they don't extend the bus. However, if a PCIe switch is connected,
then there is a problem when the downstream busses starts showing up and
the PCI core doesn't extend the subordinate bus number and bridge resources
after initial scan during boot.
The long term plan is to migrate this driver to the upcoming pwrctrl APIs
that are supposed to handle this problem elegantly.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251222064207.3246632-9-cassel@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b361b1e92be255ff923453fe8db74086cc7cf66 ]
Commit under Fixes enabled loadable module support for the driver under
the assumption that it shall be the sole user of the Cadence Host and
Endpoint library APIs. This assumption guarantees that we won't end up
in a case where the driver is built-in and the library support is built
as a loadable module.
With the introduction of [1], this assumption is no longer valid. The
SG2042 driver could be built as a loadable module, implying that the
Cadence Host library is also selected as a loadable module. However, the
pci-j721e.c driver could be built-in as indicated by CONFIG_PCI_J721E=y
due to which the Cadence Endpoint library is built-in. Despite the
library drivers being built as specified by their respective consumers,
since the 'pci-j721e.c' driver has references to the Cadence Host
library APIs as well, we run into a build error as reported at [0].
Fix this by adding config guards as a temporary workaround. The proper
fix is to split the 'pci-j721e.c' driver into independent Host and
Endpoint drivers as aligned at [2].
[0]: https://lore.kernel.org/r/202511111705.MZ7ls8Hm-lkp@intel.com/
[1]: commit 1c72774df028 ("PCI: sg2042: Add Sophgo SG2042 PCIe driver")
[2]: https://lore.kernel.org/r/37f6f8ce-12b2-44ee-a94c-f21b29c98821@app.fastmail.com/
Fixes: a2790bf81f0f ("PCI: j721e: Add support to build as a loadable module")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202511111705.MZ7ls8Hm-lkp@intel.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251117113246.1460644-1-s-vadapalli@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 46a9f70e93ef73860d1dbbec75ef840031f8f30a ]
The commit 665745f27487 ("PCI/bwctrl: Re-add BW notification portdrv as
PCIe BW controller") was found to lead to a boot hang on a Intel P45
system. Testing without setting Link Bandwidth Management Interrupt Enable
(LBMIE) and Link Autonomous Bandwidth Interrupt Enable (LABIE) (PCIe r7.0,
sec 7.5.3.7) in bwctrl allowed system to come up.
P45 is a very old chipset and supports only up to gen2 PCIe, so not having
bwctrl does not seem a huge deficiency.
Add no_bw_notif in struct pci_dev and quirk Intel P45 Root Port with it.
Reported-by: Adam Stylinski <kungfujesus06@gmail.com>
Link: https://lore.kernel.org/linux-pci/aUCt1tHhm_-XIVvi@eggsbenedict/
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Adam Stylinski <kungfujesus06@gmail.com>
Link: https://patch.msgid.link/20260116131513.2359-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c81a2ce6b6a844d1a57d2a69833a9d0f00403f00 ]
After asserting Secondary Bus Reset to downstream devices via a GB10 Root
Port, the link may not retrain correctly, e.g., the link may retrain with a
lower lane count or config accesses to downstream devices may fail.
Prevent use of Secondary Bus Reset for devices below GB10.
Signed-off-by: Johnny-CC Chang <Johnny-CC.Chang@mediatek.com>
[bhelgaas: drop pci_ids.h update (only used once), update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20251113084441.2124737-1-Johnny-CC.Chang@mediatek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 44d2f70b1fd72c339c72983fcffa181beae3e113 ]
The Qualcomm Hamoa & Glymur Root Ports don't advertise an ACS capability,
but they do provide ACS-like features to disable peer transactions and
validate bus numbers in requests.
Add an ACS quirk for Hamoa & Glymur.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260109-acs_quirk-v1-1-82adf95a89ae@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c41e2fb67e26b04d919257875fa954aa5f6e392e ]
Platform, ACPI, or IOMMU drivers call pci_request_acs(), which sets
'pci_acs_enable' to request that ACS be enabled for any devices enumerated
in the future.
OF platforms called pci_enable_acs() for the first device before
of_iommu_configure() called pci_request_acs(), so ACS was never enabled for
that device (typically a Root Port).
Call pci_enable_acs() later, from pci_dma_configure(), after
of_dma_configure() has had a chance to call pci_request_acs().
Here's the call path, showing the move of pci_enable_acs() from
pci_acs_init() to pci_dma_configure(), where it always happens after
pci_request_acs():
pci_device_add
pci_init_capabilities
pci_acs_init
- pci_enable_acs
- if (pci_acs_enable) <-- previous test
- ...
device_add
bus_notify(BUS_NOTIFY_ADD_DEVICE)
iommu_bus_notifier
iommu_probe_device
iommu_init_device
dev->bus->dma_configure
pci_dma_configure # pci_bus_type.dma_configure
of_dma_configure
of_iommu_configure
pci_request_acs
pci_acs_enable = 1 <-- set
+ pci_enable_acs
+ if (pci_acs_enable) <-- new test
+ ...
bus_probe_device
device_initial_probe
...
really_probe
dev->bus->dma_configure
pci_dma_configure # pci_bus_type.dma_configure
...
pci_enable_acs
Note that we will now call pci_enable_acs() twice for every device, first
from the iommu_probe_device() path and again from the really_probe() path.
Presumably that's not an issue since we also call dev->bus->dma_configure()
twice.
For the ACPI platforms, pci_request_acs() is called during ACPI
initialization time itself, independent of the IOMMU framework.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://patch.msgid.link/20260102-pci_acs-v3-1-72280b94d288@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1f5e57c622b4dc9b8e7d291d560138d92cfbe5bf ]
Like pci_bus_lock(), pci_slot_lock() needs to lock the bridge device to
prevent warnings like:
pcieport 0000:e2:05.0: unlocked secondary bus reset via: pciehp_reset_slot+0x55/0xa0
Take and release the lock for the bridge providing the slot for the
lock/trylock and unlock routines.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://patch.msgid.link/20260130165953.751063-3-kbusch@meta.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
