| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Following an incomplete transfer in MSG IN phase, the driver would not
notice the problem and would make use of invalid data. Initialize 'tmp'
appropriately and bail out if no message was received. For STATUS phase,
preserve the existing status code unless a new value was transferred.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/52e02a8812ae1a2d810d7f9f7fd800c3ccc320c4.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that FLAG_DMA_FIXUP has itself been fixed up, it can be used to enable
scatter/gather. Increase the default value for sg_tablesize to SG_ALL for
those systems which are compatible with FLAG_DMA_FIXUP.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/f155ba5ce93055cbc6ac6d4026673f40f826edb8.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It's not an error for a target to change the bus phase during a transfer.
Unfortunately, the FLAG_DMA_FIXUP workaround does not allow for that -- a
phase change produces a DRQ timeout error and the device borken flag will
be set.
Check the phase match bit during FLAG_DMA_FIXUP processing. Don't forget to
decrement the command residual. While we are here, change shost_printk()
into scmd_printk() for better consistency with other DMA error messages.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 55181be8ced1 ("ncr5380: Replace redundant flags with FLAG_NO_DMA_FIXUP")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/99dc7d1f4c825621b5b120963a69f6cd3e9ca659.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
SD cards can produce write latency spikes on the order of a hundred
milliseconds. If the target firmware does not hide that latency during DATA
IN and OUT phases it can cause the PDMA circuitry to raise a processor bus
fault which in turn leads to an unreliable byte count and a DMA overrun.
The Last Byte Sent flag is used to detect the overrun but this mechanism is
unreliable on some systems. Instead, set a DID_ERROR result whenever there
is a bus fault during a PDMA send, unless the cause was a phase mismatch.
Cc: stable@vger.kernel.org # 5.15+
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 7c1f3e3447a1 ("scsi: mac_scsi: Treat Last Byte Sent time-out as failure")
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/cc38df687ace2c4ffc375a683b2502fc476b600d.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Before the error handling can be revised, some preparation is needed.
Refactor the polling loop with a new function, macscsi_wait_for_drq().
This function will gain more call sites in the next patch.
Cc: stable@vger.kernel.org # 5.15+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/6a5ffabb4290c0d138c6d285fda8fa3902e926f0.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a bus fault, capture and log the chip registers immediately, if the
NDEBUG_PSEUDO_DMA macro is defined. Remove some printk(KERN_DEBUG ...)
messages that aren't needed any more. Don't skip the debug message when
bytes == 0. Show all of the byte counters in the debug messages.
Cc: stable@vger.kernel.org # 5.15+
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/7573c79f4e488fc00af2b8a191e257ca945e0409.1723001788.git.fthain@linux-m68k.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 8.10.0.5.50.
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240808125418.8832-4-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead of updating the ConsumerIndex of the Admin and Operational
ReplyQueues after processing all replies in the queue, the index will now
be periodically updated after processing every 100 replies.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240808125418.8832-3-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver masked the loginfo available bit in the iocstatus before passing
it to the applications, causing a mismatch in error messages between Linux
and other operating systems.
Modify driver to return unmasked (complete) iocstatus, including the
loginfo available bit, for the MPI commands sent through the ioctl
interface.
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20240808125418.8832-2-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In the spirit of [1], fix the copy-paste typo and use unique names for both
caches.
[1]: https://lore.kernel.org/all/20240807090746.2146479-1-pedro.falcato@gmail.com/
Signed-off-by: Pedro Falcato <pedro.falcato@gmail.com>
Link: https://lore.kernel.org/r/20240807095709.2200728-1-pedro.falcato@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit fc4444941140 ("scsi: mpi3mr: HDB allocation and posting for hardware
and firmware buffers") added mpi3mr_alloc_diag_bufs() which calls
dma_alloc_coherent() to allocate the trace buffer and the firmware
buffer. mpi3mr_alloc_diag_bufs() decides the buffer sizes from the driver
configuration. In my environment, the sizes are 8MB. With the sizes,
dma_alloc_coherent() fails and report this WARNING:
WARNING: CPU: 4 PID: 438 at mm/page_alloc.c:4676 __alloc_pages_noprof+0x52f/0x640
The WARNING indicates that the order of the allocation size is larger than
MAX_PAGE_ORDER. After this failure, mpi3mr_alloc_diag_bufs() reduces the
buffer sizes and retries dma_alloc_coherent(). In the end, the buffer
allocations succeed with 4MB size in my environment, which corresponds to
MAX_PAGE_ORDER=10. Though the allocations succeed, the WARNING message is
misleading and should be avoided.
To avoid the WARNING, check the orders of the buffer allocation sizes
before calling dma_alloc_coherent(). If the orders are larger than
MAX_PAGE_ORDER, fall back to the retry path.
Fixes: fc4444941140 ("scsi: mpi3mr: HDB allocation and posting for hardware and firmware buffers")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240810042701.661841-3-shinichiro.kawasaki@wdc.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit fc4444941140 ("scsi: mpi3mr: HDB allocation and posting for hardware
and firmware buffers") added the spinlock trigger_lock to the struct
mpi3mr_ioc. However, spin_lock_init() call was not added for it, then the
lock does not work as expected. Also, the kernel reports the message below
when lockdep is enabled.
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
To fix the issue and to avoid the INFO message, add the missing
spin_lock_init() call.
Fixes: fc4444941140 ("scsi: mpi3mr: HDB allocation and posting for hardware and firmware buffers")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240810042701.661841-2-shinichiro.kawasaki@wdc.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Flag REQ_ATOMIC can only be set for writes, so don't check if the operation
is also a write in sd_setup_read_write_cmnd().
Fixes: bf4ae8f2e640 ("scsi: sd: Atomic write support")
Signed-off-by: John Garry <john.g.garry@oracle.com>
Link: https://lore.kernel.org/r/20240805113315.1048591-2-john.g.garry@oracle.com
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two core fixes: one to prevent discard type changes (seen on iSCSI)
during intermittent errors and the other is fixing a lockdep problem
caused by the queue limits change.
And one driver fix in ufs"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Keep the discard mode stable
scsi: sd: Move sd_read_cpr() out of the q->limits_lock region
scsi: ufs: core: Fix hba->last_dme_cmd_tstamp timestamp updating logic
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core change that reverts the double message print patch in sd.c
(it was causing regressions on embedded systems).
The rest are driver fixes in ufs, mpt3sas and mpi3mr"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: exynos: Don't resume FMP when crypto support is disabled
scsi: mpt3sas: Avoid IOMMU page faults on REPORT ZONES
scsi: mpi3mr: Avoid IOMMU page faults on REPORT ZONES
scsi: ufs: core: Do not set link to OFF state while waking up from hibernation
scsi: Revert "scsi: sd: Do not repeat the starting disk message"
scsi: ufs: core: Fix deadlock during RTC update
scsi: ufs: core: Bypass quick recovery if force reset is needed
scsi: ufs: core: Check LSDBS cap when !mcq
|
|
Don Brace <don.brace@microchip.com> says:
These patches are based on Martin Petersen's 6.11/scsi-queue tree
https://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi.git 6.11/scsi-queue
The functional changes of note to smartpqi are for: multipath failover
and improving the accuracy of our RAID bypass counter.
For multipath we are:
Reverting commit 94a68c814328 ("scsi: smartpqi: Quickly propagate
path failures to SCSI midlayer") because under certain rare
conditions involving encryption-enabled devices, a false path
failure is reported to the SML causing multipath to failover to
the other path.
Improving errors returned from the driver back to the SML by
checking for error codes returned from the firmware and returning
the correct ASC/ASCQ codes to the SML.
The other two patches add PCI-IDs for new controllers and change the
driver version.
Link: https://lore.kernel.org/r/20240711194704.982400-1-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 2.1.28-025.
Reviewed-by: Mike Tran <mike.tran@microchip.com>
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240711194704.982400-6-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Improve multipath failovers by mapping firmware errors into I/O errors.
In some rare instances, firmware does not return the proper error code for
I/O errors caused by a multipath path failure.
Map I/O errors returned by firmware into errors that help the multipath
layer to detect the failure of a path.
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240711194704.982400-5-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct a rare multipath failure issue by reverting commit 94a68c814328
("scsi: smartpqi: Quickly propagate path failures to SCSI midlayer") [1].
Reason for revert: The patch propagated the path failure to SML quickly
when one of the path fails during IO and AIO path gets disabled for a
multipath device.
But it created a new issue: when creating a volume on an encryption-enabled
controller, the firmware reports the AIO path is disabled, which cause the
driver to report a path failure to SML for a multipath device.
There will be a new fix to handle "Illegal request" and "Invalid field in
parameter list" on RAID path when the AIO path is disabled on a multipath
device.
[1] https://lore.kernel.org/all/164375209313.440833.9992416628621839233.stgit@brunhilda.pdev.net/
Fixes: 94a68c814328 ("scsi: smartpqi: Quickly propagate path failures to SCSI midlayer")
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Gilbert Wu <Gilbert.Wu@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240711194704.982400-4-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The original implementation of this counter used an atomic variable.
However, this implementation negatively impacted performance in some
configurations.
Switch to using per_cpu variables.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Co-developed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240711194704.982400-3-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
All PCI ID entries in hex.
Add new inagile PCI IDs:
VID / DID / SVID / SDID
---- ---- ---- ----
SMART-HBA 8242-24i 9005 / 028f / 1ff9 / 0045
RAID 8236-16i 9005 / 028f / 1ff9 / 0046
RAID 8240-24i 9005 / 028f / 1ff9 / 0047
SMART-HBA 8238-16i 9005 / 028f / 1ff9 / 0048
PM8222-SHBA 9005 / 028f / 1ff9 / 004a
RAID PM8204-2GB 9005 / 028f / 1ff9 / 004b
RAID PM8204-4GB 9005 / 028f / 1ff9 / 004c
PM8222-HBA 9005 / 028f / 1ff9 / 004f
MT0804M6R 9005 / 028f / 1ff9 / 0051
MT0801M6E 9005 / 028f / 1ff9 / 0052
MT0808M6R 9005 / 028f / 1ff9 / 0053
MT0800M6H 9005 / 028f / 1ff9 / 0054
RS0800M5H24i 9005 / 028f / 1ff9 / 006b
RS0800M5E8i 9005 / 028f / 1ff9 / 006c
RS0800M5H8i 9005 / 028f / 1ff9 / 006d
RS0804M5R16i 9005 / 028f / 1ff9 / 006f
RS0800M5E24i 9005 / 028f / 1ff9 / 0070
RS0800M5H16i 9005 / 028f / 1ff9 / 0071
RS0800M5E16i 9005 / 028f / 1ff9 / 0072
RT0800M7E 9005 / 028f / 1ff9 / 0086
RT0800M7H 9005 / 028f / 1ff9 / 0087
RT0804M7R 9005 / 028f / 1ff9 / 0088
RT0808M7R 9005 / 028f / 1ff9 / 0089
RT1608M6R16i 9005 / 028f / 1ff9 / 00a1
Add new h3c pci_id:
VID / DID / SVID / SDID
---- ---- ---- ----
UN RAID P4408-Mr-2 9005 / 028f / 193d / 1110
Add new powerleader pci ids:
VID / DID / SVID / SDID
---- ---- ---- ----
PL SmartROC PM8204 9005 / 028f / 1f3a / 0104
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: David Strahan <David.Strahan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20240711194704.982400-2-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is a scenario where a large number of discard commands are issued
when the iscsi initiator connects to the target and then performs a session
rescan operation. There is a time window, most of the commands are in UNMAP
mode, and some discard commands become WRITE SAME with UNMAP.
The discard mode has been negotiated during the SCSI probe. If the mode is
temporarily changed from UNMAP to WRITE SAME with UNMAP, an I/O ERROR may
occur because the target may not implement WRITE SAME with UNMAP. Keep the
discard mode stable to fix this issue.
Signed-off-by: Li Feng <fengli@smartx.com>
Link: https://lore.kernel.org/r/20240718080751.313102-2-fengli@smartx.com
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Justin Tee <justintee8345@gmail.com> says:
Update lpfc to revision 14.4.0.4
This patch set contains diagnostic logging improvements, a minor clean
up when submitting abort requests, a bug fix related to reset and
errata paths, and modifications to FLOGI and PRLO ELS command
handling.
The patches were cut against Martin's 6.11/scsi-queue tree.
Link: https://lore.kernel.org/r/20240726231512.92867-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update copyrights to 2024 for files modified in the 14.4.0.4 patch set.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-9-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update lpfc version to 14.4.0.4
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-8-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A kref imbalance occurs when handling an unsolicited PRLO in direct
attached topology.
Rework PRLO rcv handling when in MAPPED state. Save the state that we were
handling a PRLO by setting nlp_last_elscmd to ELS_CMD_PRLO. Then in the
lpfc_cmpl_els_logo_acc() completion routine, manually restart discovery.
By issuing the PLOGI, which nlp_gets, before nlp_put at the end of the
lpfc_cmpl_els_logo_acc() routine, we are saving us from a final nlp_put.
And, we are still allowing the unreg_rpi to happen.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-7-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
topology
In direct attached topology, certain target vendors that are quick to issue
FLOGI followed by a cable pull for more than dev_loss_tmo may result in a
kref imbalance for the remote port ndlp object.
Add an nlp_get when the defer_flogi_acc flag is set. This is expected to
balance the nlp_put in the defer_flogi_acc clause in the
lpfc_issue_els_flogi() routine. Because we need to retain the ndlp ptr,
reorganize all of the defer_flogi_acc information into one
lpfc_defer_flogi_acc struct.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-6-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The vport->vmid_flag is unintentionally cleared twice after an issue_lip
via the lpfc_reinit_vmid routine().
The first call to lpfc_reinit_vmid() is in lpfc_cmpl_els_flogi(). Then
lpfc_cmpl_els_flogi_fabric() calls lpfc_register_new_vport(), which calls
lpfc_cmpl_reg_new_vport() when the mbox command completes and calls
lpfc_reinit_vmid() a second time.
Fix by moving the vmid_flag clear outside of the lpfc_reinit_vmid() routine
so that vmid_flag is only cleared once upon FLOGI completion.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-5-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the HBA is undergoing a reset or is handling an errata event, NULL ptr
dereference crashes may occur in routines such as
lpfc_sli_flush_io_rings(), lpfc_dev_loss_tmo_callbk(), or
lpfc_abort_handler().
Add NULL ptr checks before dereferencing hdwq pointers that may have been
freed due to operations colliding with a reset or errata event handler.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-4-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lpfc_sli_issue_abort_iotag() routine has a redundant assignment of
abtsiocbp->vport = vport;
The duplicate lines are from a previous refactoring, and this patch removes
the accidental redundancy.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-3-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During diagnostics, it has been determined that the 0115 log message for
receipt of unknown ELS cmds does not benefit from trace buffer dumps. The
trace buffer dump floods the console with unnecessary information, and the
singular LOG_ELS flag has proven more beneficial in debugging efforts when
dealing with unknown ELS cmds.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20240726231512.92867-2-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
with flexible arrays"
Kees Cook <kees@kernel.org> says:
This replaces some of the last remaining uses in the kernel of
1-element "fake" flexible arrays with modern C99 flexible arrays. Some
refactoring is done to ease this, and binary differences are
identified. For the on stack size changes in patch 2, the "yes, that
is the source of the binary differences" debugging patch can be found
here[1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux.git/commit/?h=dev/v6.10-rc2/1-element&id=45e6226bcbc5e982541754eca7ac29f403e82f5e
Link: https://lore.kernel.org/r/20240711212732.work.162-kees@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible arrays
Replace the deprecated[1] use of 1-element arrays in struct sgmap, struct
sgmap64, struct sgmapraw, struct user_sgmap, and struct user_sgmap64 with
modern flexible arrays. Additionally remove struct user_sgmapraw as it is
unused.
The resulting binary output differences from this change are limited only
to stack space consumption of the smaller "srbu" variable in
aac_issue_safw_bmic_identify() and aac_get_safw_ciss_luns(), as well as the
smaller associated pair of memcpy()s in
aac_send_safw_bmic_cmd(). Artificially growing the size of srbu back to its
prior size removes all binary differences[2].
As an aside, after studying the aacraid driver code I wonder how
aac_send_wellness_command() ever works. It is reporting a size 4 bytes too
small for what it has constructed in memory in the DMA region: sgentry64 is
size 12, whereas sgentry is size 8. Perhaps the hardware doesn't
care. (Regardless, it is unchanged by this patch.)
Link: https://github.com/KSPP/linux/issues/79 [1]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux.git/commit/?h=dev/v6.10-rc2/1-element&id=45e6226bcbc5e982541754eca7ac29f403e82f5e [2]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711215739.208776-2-kees@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
struct aac_srb_unit contains struct aac_srb, which contains struct sgmap,
which ends in a (currently) "fake" (1-element) flexible array. Converting
this to a flexible array is needed so that runtime bounds checking won't
think the array is fixed size (i.e. under CONFIG_FORTIFY_SOURCE=y and/or
CONFIG_UBSAN_BOUNDS=y), as other parts of aacraid use struct sgmap as a
flexible array.
It is not legal to have a flexible array in the middle of a structure, so
it either needs to be split up or rearranged so that it is at the end of
the structure. Luckily, struct aac_srb_unit, which is exclusively
consumed/updated by aac_send_safw_bmic_cmd(), does not depend on member
ordering.
The values set in the on-stack struct aac_srb_unit instance "srbu" by the
only two callers, aac_issue_safw_bmic_identify() and
aac_get_safw_ciss_luns(), do not contain anything in srbu.srb.sgmap.sg, and
they both implicitly initialize srbu.srb.sgmap.count to 0 during
memset(). For example:
memset(&srbu, 0, sizeof(struct aac_srb_unit));
srbcmd = &srbu.srb;
srbcmd->flags = cpu_to_le32(SRB_DataIn);
srbcmd->cdb[0] = CISS_REPORT_PHYSICAL_LUNS;
srbcmd->cdb[1] = 2; /* extended reporting */
srbcmd->cdb[8] = (u8)(datasize >> 8);
srbcmd->cdb[9] = (u8)(datasize);
rcode = aac_send_safw_bmic_cmd(dev, &srbu, phys_luns, datasize);
During aac_send_safw_bmic_cmd(), a separate srb is mapped into DMA, and has
srbu.srb copied into it:
srb = fib_data(fibptr);
memcpy(srb, &srbu->srb, sizeof(struct aac_srb));
Only then is srb.sgmap.count written and srb->sg populated:
srb->count = cpu_to_le32(xfer_len);
sg64 = (struct sgmap64 *)&srb->sg;
sg64->count = cpu_to_le32(1);
sg64->sg[0].addr[1] = cpu_to_le32(upper_32_bits(addr));
sg64->sg[0].addr[0] = cpu_to_le32(lower_32_bits(addr));
sg64->sg[0].count = cpu_to_le32(xfer_len);
But this is happening in the DMA memory, not in srbu.srb. An attempt to
copy the changes back to srbu does happen:
/*
* Copy the updated data for other dumping or other usage if
* needed
*/
memcpy(&srbu->srb, srb, sizeof(struct aac_srb));
But this was never correct: the sg64 (3 u32s) overlap of srb.sg (2 u32s)
always meant that srbu.srb would have held truncated information and any
attempt to walk srbu.srb.sg.sg based on the value of srbu.srb.sg.count
would result in attempting to parse past the end of srbu.srb.sg.sg[0] into
srbu.srb_reply.
After getting a reply from hardware, the reply is copied into
srbu.srb_reply:
srb_reply = (struct aac_srb_reply *)fib_data(fibptr);
memcpy(&srbu->srb_reply, srb_reply, sizeof(struct aac_srb_reply));
This has always been fixed-size, so there's no issue here. It is worth
noting that the two callers _never check_ srbu contents -- neither
srbu.srb nor srbu.srb_reply is examined. (They depend on the mapped
xfer_buf instead.)
Therefore, the ordering of members in struct aac_srb_unit does not matter,
and the flexible array member can moved to the end.
(Additionally, the two memcpy()s that update srbu could be entirely
removed as they are never consumed, but I left that as-is.)
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711215739.208776-1-kees@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace the deprecated[1] use of a 1-element arrays in struct
ipr_hostrcb_fabric_desc and struct ipr_hostrcb64_fabric_desc with modern
flexible arrays.
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711180702.work.536-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible array
Replace the deprecated[1] use of a 1-element array in struct
aac_ciss_phys_luns_resp with a modern flexible array.
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711175055.work.928-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace the deprecated[1] use of a 1-element array in union aac_init with a
modern flexible array.
Additionally add __counted_by annotation since rrq is only ever accessed
after rr_queue_count has been set (with the same value used to control the
loop):
init->r8.rr_queue_count = cpu_to_le32(dev->max_msix);
...
for (i = 0; i < dev->max_msix; i++) {
addr = (u64)dev->host_rrq_pa + dev->vector_cap * i *
sizeof(u32);
init->r8.rrq[i].host_addr_high = cpu_to_le32(
upper_32_bits(addr));
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711174815.work.689-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible array
Replace the deprecated[1] use of a 1-element array in struct
MR_HOST_DEVICE_LIST with a modern flexible array.
One binary difference appears in megasas_host_device_list_query():
struct MR_HOST_DEVICE_LIST *ci;
...
ci = instance->host_device_list_buf;
...
memset(ci, 0, sizeof(*ci));
The memset() clears only the non-flexible array fields. Looking at the rest
of the function, this appears to be fine: firmware is using this region to
communicate with the kernel, so it likely never made sense to clear the
first MR_HOST_DEVICE_LIST_ENTRY.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155841.work.839-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible arrays
Replace the deprecated[1] use of a 1-element array in struct MR_LD_VF_MAP
with a modern flexible array.
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155823.work.778-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible array
Replace the deprecated[1] use of a 1-element array in struct
mpi3_sas_io_unit_page1 with a modern flexible array.
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155637.3757036-4-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
flexible array
Replace the deprecated[1] use of a 1-element array in struct
mpi3_sas_io_unit_page0 with a modern flexible array.
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155637.3757036-3-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
1-element array with flexible array
Replace the deprecated[1] use of a 1-element array in struct
mpi3_event_data_pcie_topology_change_list with a modern flexible array.
Additionally add __counted_by annotation since port_entry is only ever
accessed in loops controlled by num_entries. For example:
for (i = 0; i < event_data->num_entries; i++) {
handle =
le16_to_cpu(event_data->port_entry[i].attached_dev_handle);
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155637.3757036-2-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
1-element array with flexible array
Replace the deprecated[1] use of a 1-element array in struct
mpi3_event_data_sas_topology_change_list with a modern flexible array.
Additionally add __counted_by annotation since phy_entry is only ever
accessed in loops controlled by num_entries. For example:
for (i = 0; i < event_data->num_entries; i++) {
...
handle = le16_to_cpu(event_data->phy_entry[i].attached_dev_handle);
No binary differences are present after this conversion.
Link: https://github.com/KSPP/linux/issues/79 [1]
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://lore.kernel.org/r/20240711155637.3757036-1-kees@kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 804e498e0496 ("sd: convert to the atomic queue limits API")
introduced pairs of function calls to queue_limits_start_update() and
queue_limits_commit_update(). These two functions lock and unlock
q->limits_lock. In sd_revalidate_disk(), sd_read_cpr() is called after
queue_limits_start_update() call and before queue_limits_commit_update()
call. sd_read_cpr() locks q->sysfs_dir_lock and &q->sysfs_lock. Then new
lock dependencies were created between q->limits_lock, q->sysfs_dir_lock
and q->sysfs_lock, as follows:
sd_revalidate_disk
queue_limits_start_update
mutex_lock(&q->limits_lock)
sd_read_cpr
disk_set_independent_access_ranges
mutex_lock(&q->sysfs_dir_lock)
mutex_lock(&q->sysfs_lock)
mutex_unlock(&q->sysfs_lock)
mutex_unlock(&q->sysfs_dir_lock)
queue_limits_commit_update
mutex_unlock(&q->limits_lock)
However, the three locks already had reversed dependencies in other
places. Then the new dependencies triggered the lockdep WARN "possible
circular locking dependency detected" [1]. This WARN was observed by
running the blktests test case srp/002.
To avoid the WARN, move the sd_read_cpr() call in sd_revalidate_disk()
after the queue_limits_commit_update() call. In other words, move the
sd_read_cpr() call out of the q->limits_lock region.
[1] https://lore.kernel.org/linux-scsi/vlmv53ni3ltwxplig5qnw4xsl2h6ccxijfbqzekx76vxoim5a5@dekv7q3es3tx/
Fixes: 804e498e0496 ("sd: convert to the atomic queue limits API")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240801054234.540532-1-shinichiro.kawasaki@wdc.com
Tested-by: Luca Coelho <luciano.coelho@intel.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function ata_noop_qc_prep(), as its name implies, does nothing and
simply returns AC_ERR_OK. For drivers that do not need any special
preparations of queued commands, we can avoid having to define struct
ata_port qc_prep operation by simply testing if that operation is
defined or not in ata_qc_issue(). Make this change and remove
ata_noop_qc_prep().
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
|
|
Pull outstanding commits from 6.11 queue into fixes.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While working on simplifying the minmax functions, and avoiding
excessive macro expansion, it turns out that the sr.c use of the
'clamp()' macro has the arguments the wrong way around.
The clamp logic is
val = clamp(in, low, high);
and it returns the input clamped to the low/high limits. But sr.c ddid
speed = clamp(0, speed, 0xffff / 177);
which clamps the value '0' to the range '[speed, 0xffff / 177]' and ends
up being nonsensical.
Happily, I don't think anybody ever cared.
Fixes: 9fad9d560af5 ("scsi: sr: Fix unintentional arithmetic wraparound")
Cc: Justin Stitt <justinstitt@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This just standardizes the use of MIN() and MAX() macros, with the very
traditional semantics. The goal is to use these for C constant
expressions and for top-level / static initializers, and so be able to
simplify the min()/max() macros.
These macro names were used by various kernel code - they are very
traditional, after all - and all such users have been fixed up, with a
few different approaches:
- trivial duplicated macro definitions have been removed
Note that 'trivial' here means that it's obviously kernel code that
already included all the major kernel headers, and thus gets the new
generic MIN/MAX macros automatically.
- non-trivial duplicated macro definitions are guarded with #ifndef
This is the "yes, they define their own versions, but no, the include
situation is not entirely obvious, and maybe they don't get the
generic version automatically" case.
- strange use case #1
A couple of drivers decided that the way they want to describe their
versioning is with
#define MAJ 1
#define MIN 2
#define DRV_VERSION __stringify(MAJ) "." __stringify(MIN)
which adds zero value and I just did my Alexander the Great
impersonation, and rewrote that pointless Gordian knot as
#define DRV_VERSION "1.2"
instead.
- strange use case #2
A couple of drivers thought that it's a good idea to have a random
'MIN' or 'MAX' define for a value or index into a table, rather than
the traditional macro that takes arguments.
These values were re-written as C enum's instead. The new
function-line macros only expand when followed by an open
parenthesis, and thus don't clash with enum use.
Happily, there weren't really all that many of these cases, and a lot of
users already had the pattern of using '#ifndef' guarding (or in one
case just using '#undef MIN' |
