| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Like other SPI controller flags, bits_per_word_mask may be used by a
peripheral driver, so it needs to reflect the capabilities of the
underlying controller.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240708-spi-mux-fix-v1-3-6c8845193128@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Adding spi_optimize_message() broke the spi-mux driver because it
calls spi_async() from it's transfer_one_message() callback. This
resulted in passing an incorrectly optimized message to the controller.
For example, if the underlying controller has an optimize_message()
callback, this would have not been called and can cause a crash when
the underlying controller driver tries to transfer the message.
Also, since the spi-mux driver swaps out the controller pointer by
replacing msg->spi, __spi_unoptimize_message() was being called with a
different controller than the one used in __spi_optimize_message(). This
could cause a crash when attempting to free the message resources when
__spi_unoptimize_message() is called in spi_finalize_current_message()
since it is being called with a controller that did not allocate the
resources.
This is fixed by adding a defer_optimize_message flag for controllers.
This flag causes all of the spi_[maybe_][un]optimize_message() calls to
be a no-op (other than attaching a pointer to the spi device to the
message).
This allows the spi-mux driver to pass an unmodified message to
spi_async() in spi_mux_transfer_one_message() after the spi device has
been swapped out. This causes __spi_optimize_message() and
__spi_unoptimize_message() to be called only once per message and with
the correct/same controller in each case.
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Closes: https://lore.kernel.org/linux-spi/Zn6HMrYG2b7epUxT@pengutronix.de/
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/linux-spi/20240628-awesome-discerning-bear-1621f9-mkl@pengutronix.de/
Fixes: 7b1d87af14d9 ("spi: add spi_optimize_message() APIs")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240708-spi-mux-fix-v1-2-6c8845193128@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Calling spi_maybe_unoptimize_message() in spi_async() is wrong because
the message is likely to be in the queue and not transferred yet. This
can corrupt the message while it is being used by the controller driver.
spi_maybe_unoptimize_message() is already called in the correct place
in spi_finalize_current_message() to balance the call to
spi_maybe_optimize_message() in spi_async().
Fixes: 7b1d87af14d9 ("spi: add spi_optimize_message() APIs")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240708-spi-mux-fix-v1-1-6c8845193128@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a driver for the QiHeng Electronics ch341a USB-to-SPI adapter.
This driver is loosely based on the ch341a module from the flashrom project.
Signed-off-by: Johannes Thumshirn <jth@kernel.org>
Link: https://patch.msgid.link/20240708-spi-ch341a-v3-1-cf7f9b2c1e31@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
status is assigned first, so it does not need to initialize the assignment.
Signed-off-by: Li zeming <zeming@nfschina.com>
Link: https://patch.msgid.link/20240708041411.14424-1-zeming@nfschina.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rc is assigned first, so it does not need to initialize the assignment.
Signed-off-by: Li zeming <zeming@nfschina.com>
Link: https://patch.msgid.link/20240708035320.14241-1-zeming@nfschina.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Just cosmetics. No functional change intended.
While at it, removed a couple of redundant else if() statements.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240705-dev-spi-xcomm-gpiochip-v2-4-b10842fc9636@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
i2c_get_clientdata() is not being called anywhere so that we do not need
to set clientdata.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240705-dev-spi-xcomm-gpiochip-v2-3-b10842fc9636@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_spi_alloc_host() so that there's no need to call
spi_controller_put() in the error path.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240705-dev-spi-xcomm-gpiochip-v2-2-b10842fc9636@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The hardware can expose one pin as a GPO. Hence, register a simple
gpiochip to support it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Co-developed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240705-dev-spi-xcomm-gpiochip-v2-1-b10842fc9636@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There have been multiple reports that the multi-mode support in the
OMAP2 McSPI driver has caused regressions on existing systems. There's
been some discussion and some proposed changes but nothing that's been
tested by all the reporters. Drop the patch for v6.10, hopefully we can
get to the bottom of the issue and reenable the feature for v6.11.
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Reported-by: João Paulo Gonçalves <jpaulo.silvagoncalves@gmail.com>
Fixes: e64d3b6fc9a3 ("spi: omap2-mcpsi: Enable MULTI-mode in more situations")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20240704-spi-revert-omap2-multi-v1-1-69357ef13fdc@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 2nd set of new device support, features and cleanup for 6.11
The big one here is we finally have Paul Cercueil's (and others)
DMA buffer support for IIO devices enabling high speed zero
copy transfer of data to and from sensors supported by IIO (and for
example USB). This should aid with upstream support of a range of
higher performance ADCs and DACs.
Two merges from other trees
- spi/spi_devm_optimize used for simplification in ad7944.
- dmaengine/topic_dma_vec to enable the DMABUF series.
One feature with impact outside IIO.
- Richer set of dev_err_probe() like helpers to cover ERR_PTR() cases.
New device support
==================
adi,ad7173
- Add support for AD4111, AD4112, AD4114, AD4115 and ADC4116 pseudo
differential ADCs. Major driver rework was needed to enabled these.
adi,ad7944
- Use devm_spi_optimize_message() to avoid a local devm cleanup
callback. This is the example case from the patch set, others will
follow.
mediatek,mt6359-auxadc
- New driver for this ADC IP found in MT6357, MT6358 and MT6359 PMICs.
st,accel
- Add support for the LIS2DS12 accelerometer
ti,ads1119
- New driver for this 16 bit 2-differential or 4-single ended channel
ADC.
Features
========
dt-bindings
- Introduce new common-mode-channel property to help handle pseudo
differential ADCs where we have something that looks like one side
of differential input, but which is only suited for use with a
slow moving reference.
adi,adf4350
- Support use as a clock provider.
iio-hmwon
- Support reading of labels from IIO devices by their consumers and
use this in the hwmon bridge.
Cleanup and minor fixes
=======================
Treewide
- Use regmap_clear_bits() / regmap_set_bits() to simplify open coded
equivalents.
- Use devm_regulator_get_enable_read_voltage() to replace equivalent
opencoded boilerplate. In some cases enabled complete conversion to
devm handling and removal of explicit remove() callbacks.
- Introduce dev_err_ptr_probe() and other variants and make use of
of them in a couple of examples driver cleanups. Will find use in
many more drivers soon.
adi,ad7192
- Introduce local struct device *dev and use dev_err_probe() to give
more readable code.
adi,adi-axi-adc/dac
- Improved consistency of messages using dev_err_probe()
adi,adis
- Split the trigger handling into cases that needed paging and those that
don't resulting in more readable code.
- Use cleanup.h to simplify error paths via scoped cleanup.
- Add adis specific lock helpers and make use of them in a number of drivers.
adi,ad7192
- Update maintainer (Alisa-Dariana Roman)
adi,ad7606
- dt-binding cleanup.
avago,apds9306
- Add a maintainer entry (Subhajit Ghosh)
linear,ltc2309
- Fix a wrong endian type.
st,stm32-dfsdm
- Fix a missing port property in the dt-binding.
st,sensors
- Relax whoami match failure to a warning print rather than probe failure.
This enables fallback compatibles to existing parts from those that don't
necessarily even exit yet.
* tag 'iio-for-6.11b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (112 commits)
iio: adc: ad7173: Fix uninitialized symbol is_current_chan
iio: adc: Add support for MediaTek MT6357/8/9 Auxiliary ADC
math.h: Add unsigned 8 bits fractional numbers type
dt-bindings: iio: adc: Add MediaTek MT6359 PMIC AUXADC
iio: common: scmi_iio: convert to dev_err_probe()
iio: backend: make use of dev_err_cast_probe()
iio: temperature: ltc2983: convert to dev_err_probe()
dev_printk: add new dev_err_probe() helpers
iio: xilinx-ams: Add labels
iio: adc: ad7944: use devm_spi_optimize_message()
Documentation: iio: Document high-speed DMABUF based API
iio: buffer-dmaengine: Support new DMABUF based userspace API
iio: buffer-dma: Enable support for DMABUFs
iio: core: Add new DMABUF interface infrastructure
MAINTAINERS: Update AD7192 driver maintainer
iio: adc: ad7192: use devm_regulator_get_enable_read_voltage
iio: st_sensors: relax WhoAmI check in st_sensors_verify_id()
MAINTAINERS: Add AVAGO APDS9306
dt-bindings: iio: adc: adi,ad7606: comment and sort the compatible names
dt-bindings: iio: adc: adi,ad7606: add missing datasheet link
...
|
|
'devmodel' hasn't actually been used since:
'commit 3275158fa52a ("parport: remove use of devmodel")'
and everyone now has it set to true and has been fixed up; remove
the flag.
(There are still comments all over about it)
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20240502154823.67235-4-linux@treblig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use SPI common DT binding properties 'spi-cs-setup-delay-ns' and
'spi-cs-hold-delay-ns'. If these properties do not exist, fall back to
legacy 'fsl,spi-cs-sck-delay' and 'fsl,spi-sck-cs-delay'.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20240624-ls_qspi-v4-1-3d1c6f5005bf@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On the OMAPL138, the SPI reference clock is provided by the Power and
Sleep Controller (PSC). The PSC's datasheet says that 'some peripherals
have special programming requirements and additional recommended steps
you must take before you can invoke the PSC module state transition'. I
didn't find more details in documentation but it appears that PSC needs
the SPI to clear the POWERDOWN bit before disabling the clock. Indeed,
when this bit is set, the PSC gets stuck in transitions from enable to
disable state.
Clear the POWERDOWN bit when releasing driver's resources
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20240624071745.17409-1-bastien.curutchet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
platform_get_drvdata() is never called in the AXI SPI Engine driver, so
platform_set_drvdata() is not needed. Remove it. This also lets us
avoid the final error check in the probe function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240626-spi-axi-spi-engine-remove-drvdata-v1-1-1752e372dd5d@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After coverting to SYSTEM_SLEEP_PM_OPS, it is necessary to pass pm_ptr()
to the PM operations.
Fix it accordingly.
Fixes: 6765e859fac9 ("spi: spi-fsl-lpspi: Switch to SYSTEM_SLEEP_PM_OPS()")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20240625183919.368770-2-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After coverting to RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS, it is necessary
to pass pm_ptr() to the PM operations.
Fix it accordingly.
Fixes: a93f089ccf82 ("spi: spi-imx: Switch to RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20240625183919.368770-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from David Lechner <dlechner@baylibre.com>:
In the IIO subsystem, we are finding that it is common to call
spi_optimize_message() during driver probe since the SPI message
doesn't change for the lifetime of the driver. This patch adds a
devm_spi_optimize_message() helper to simplify this common pattern.
|
|
Replace SET_SYSTEM_SLEEP_PM_OPS with its modern SYSTEM_SLEEP_PM_OPS()
alternative.
The combined usage of pm_ptr() and SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20240625002023.228235-2-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace SET_RUNTIME_PM_OPS()/SET SYSTEM_SLEEP_PM_OPS() with their modern
RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() alternatives.
The combined usage of pm_ptr() and RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20240625002023.228235-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
devm_spi_optimize_message() is a public function and needs
EXPORT_SYMBOL_GPL.
Reported-by: Jonathan Cameron <jic23@kernel.org>
Closes: https://lore.kernel.org/linux-iio/20240624204424.6a91a5e4@jic23-huawei/
Fixes: d4a0055fdc22 ("spi: add devm_spi_optimize_message() helper")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240624-devm_spi_optimize_message-v2-1-58155c0180c2@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sleep calculation was not taking into account increased delay when
the SPI device is not running at the maximum SCLK frequency.
Rounding down when one SCLK tick was the same as the instruction
execution time was fine, but it rounds down too much when SCLK is
slower. This changes the rounding to round up instead while still
taking into account the instruction execution time so that small
delays remain accurate.
Fixes: be9070bcf670 ("spi: axi-spi-engine: fix sleep ticks calculation")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240620-spi-axi-spi-engine-fix-sleep-time-v1-1-b20b527924a0@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from David Lechner <dlechner@baylibre.com>:
In the IIO subsystem, we are finding that it is common to call
spi_optimize_message() during driver probe since the SPI message
doesn't change for the lifetime of the driver. This patch adds a
devm_spi_optimize_message() helper to simplify this common pattern.
|
|
This adds a new helper function devm_spi_optimize_message() that
automatically registers spi_unoptimize_message() to be called
when the device is removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240621-devm_spi_optimize_message-v1-2-3f9dcba6e95e@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While in commit 2dd33f9cec90 ("spi: imx: support DMA for imx35") it was
claimed that DMA works on i.MX25, i.MX31 and i.MX35 the respective
device trees don't add DMA channels. The Reference manuals of i.MX31 and
i.MX25 also don't mention the CSPI core being DMA capable. (I didn't
check the others.)
Since commit e267a5b3ec59 ("spi: spi-imx: Use dev_err_probe for failed
DMA channel requests") this results in an error message
spi_imx 43fa4000.spi: error -ENODEV: can't get the TX DMA channel!
during boot. However that isn't fatal and the driver gets loaded just
fine, just without using DMA.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://patch.msgid.link/20240508095610.2146640-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
OEMs can connect a number of types of speakers to the sidecar cs35l56
amplifiers and a different speaker requires a different firmware
configuration.
When the cs42l43 ACPI includes a property indicating a particular type
of speaker has been installed this should be passed to the cs35l56
driver instances as a device property.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240619121703.3411989-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor accessing the SDCA extension properties to make it easier to
access multiple properties to assist with future features. Return the
node itself and allow the caller to read the actual properties.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240619121703.3411989-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We need the fixes to apply new changes to the Cirrus drivers.
|
|
The patch 15a6af94a277 ("spi: Increase imx51 ecspi burst length based
on transfer length") increased the burst length calculation in
mx51_ecspi_prepare_transfer() to be based on the transfer length.
This breaks HW CS + SPI_CS_WORD support which was added in
6e95b23a5b2d ("spi: imx: Implement support for CS_WORD") and transfers
with bits-per-word != 8, 16, 32.
SPI_CS_WORD means the CS should be toggled after each word. The
implementation in the imx-spi driver relies on the fact that the HW CS
is toggled automatically by the controller after each burst length
number of bits. Setting the burst length to the number of bits of the
_whole_ message breaks this use case.
Further the patch 15a6af94a277 ("spi: Increase imx51 ecspi burst
length based on transfer length") claims to optimize the transfers.
But even without this patch, on modern spi-imx controllers with
"dynamic_burst = true" (imx51, imx6 and newer), the transfers are
already optimized, i.e. the burst length is dynamically adjusted in
spi_imx_push() to avoid the pause between the SPI bursts. This has
been confirmed by a scope measurement on an imx6d.
Subsequent Patches tried to fix these and other problems:
- 5f66db08cbd3 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
- e9b220aeacf1 ("spi: spi-imx: correctly configure burst length when using dma")
- c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
- cf6d79a0f576 ("spi: spi-imx: fix off-by-one in mx51 CPU mode burst length")
but the HW CS + SPI_CS_WORD use case is still broken.
To fix the problems revert the burst size calculation in
mx51_ecspi_prepare_transfer() back to the original form, before
15a6af94a277 ("spi: Increase imx51 ecspi burst length based on
transfer length") was applied.
Cc: Stefan Moring <stefan.moring@technolution.nl>
Cc: Stefan Bigler <linux@bigler.io>
Cc: Clark Wang <xiaoning.wang@nxp.com>
Cc: Carlos Song <carlos.song@nxp.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Thorsten Scherer <T.Scherer@eckelmann.de>
Fixes: 15a6af94a277 ("spi: Increase imx51 ecspi burst length based on transfer length")
Fixes: 5f66db08cbd3 ("spi: imx: Take in account bits per word instead of assuming 8-bits")
Fixes: e9b220aeacf1 ("spi: spi-imx: correctly configure burst length when using dma")
Fixes: c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
Fixes: cf6d79a0f576 ("spi: spi-imx: fix off-by-one in mx51 CPU mode burst length")
Link: https://lore.kernel.org/all/20240618-oxpecker-of-ideal-mastery-db59f8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Thorsten Scherer <t.scherer@eckelmann.de>
Link: https://msgid.link/r/20240618-spi-imx-fix-bustlength-v1-1-2053dd5fdf87@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When spi-cadence is configured as a slave, it requires the SPI refclk to
detect the synchronization start condition while communicating with the
master. However, the spi-cadence driver never enables the SPI refclk in
slave mode, causing the refclk to remain disabled if the
"clk_ignore_unused" kernel parameter is not passed through bootargs.
As a result, the slave cannot detect data sent by the master, leading to
communication failure. Update driver to enable the SPI refclk in both
master and slave configurations.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20240617153837.29861-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While adding a SPI device, the SPI core ensures that multiple logical CS
doesn't map to the same physical CS. For example, spi->chip_select[0] !=
spi->chip_select[1] and so forth. However, unlike the SPI master, the SPI
slave doesn't have the list of chip selects, this leads to probe failure
when the SPI controller is configured as slave. Update the
__spi_add_device() function to perform this check only if the SPI
controller is configured as master.
Fixes: 4d8ff6b0991d ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20240617153052.26636-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Refactor accessing the SDCA extension properties to make it easier to
access multiple properties to assist with future features. Return the
node itself and allow the caller to read the actual properties.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://msgid.link/r/20240611132556.1557075-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add OCTAL mode support.
Issue detected using "--octal" spidev_test's option.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In case usage of OCTAL mode, buswidth parameter can take the value 8.
As return value of stm32_qspi_get_mode() is used to configure fields
of CCR registers that are 2 bits only (fields IMODE, ADMODE, ADSIZE,
DMODE), clamp return value of stm32_qspi_get_mode() to 4.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Misplaced parenthesis make test of mode wrong in case mode is equal to
SPI_TX_OCTAL or SPI_RX_OCTAL.
Simplify this sanity test, if one of this bit is set, property
cs-gpio must be present in DT.
Fixes: a557fca630cc ("spi: stm32_qspi: Add transfer_one_message() spi callback")
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://msgid.link/r/20240618132951.2743935-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add spicc loopback mode for debugging convenience.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240612-spi_lbc-v1-1-d52e8c8011bd@amlogic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
The first part of the series (patches 1 to 7) is an introduction
of a new helper followed by the user conversion.
This consolidates the same code and also makes patch 8 (last one)
be localised to the SPI core part.
The last patch is the main rework to get rid of a recently introduced
hack with a dummy SG list and move to the transfer-based DMA mapped
flag.
That said, the patches 1 to 7 may be applied right away since they
have no functional change intended, while the last one needs more
testing and reviewing.
|
|
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/spi/spi-altera-core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/spi/spi-fsl-lib.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/spi/spi-omap2-mcspi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/spi/spi-qup.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240609-md-drivers-spi-v1-1-1c7444f53cde@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add SPI clock flag CLK_SET_RATE_PARENT for using pclk as parent clock.
This gives SPI more flexibility in frequency selection.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20240524-spi_pclk_setparent-v1-1-99e0ce70b66f@amlogic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The granularity of DMA mappings is transfer and moreover,
the direction is also important as it can be unidirect.
The current cur_msg_mapped flag doesn't fit well the DMA mapping
and syncing calls and we have tons of checks around on top of it.
So, instead of doing that rework the code to use per transfer per
direction flag to show if it's DMA mapped or not.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-9-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-8-andriy.shevchenko@linux.intel.com
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-7-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-6-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-5-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-4-andriy.shevchenko@linux.intel.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace a few lines of code by calling a spi_xfer_is_dma_mapped() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-3-andriy.shevchenko@linux.intel.com
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are few drivers that use the same pattern to check if the transfer
is DMA mapped or not. Provide a helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Link: https://lore.kernel.org/r/20240531194723.1761567-2-andriy.shevchenko@linux.intel.com
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
