summaryrefslogtreecommitdiff
path: root/drivers/tty
AgeCommit message (Collapse)AuthorFilesLines
2020-11-10serial: txx9: add missing platform_driver_unregister() on error in ↵Qinglang Miao1-0/+3
serial_txx9_init commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream. Add the missing platform_driver_unregister() before return from serial_txx9_init in the error handling case when failed to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI defined. Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10serial: 8250_mtk: Fix uart_get_baud_rate warningClaire Chang1-1/+1
commit 912ab37c798770f21b182d656937072b58553378 upstream. Mediatek 8250 port supports speed higher than uartclk / 16. If the baud rates in both the new and the old termios setting are higher than uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered. Passing NULL as the old termios so uart_get_baud_rate() will use uartclk / 16 - 1 as the new baud rate which will be replaced by the original baud rate later by tty_termios_encode_baud_rate() in mtk8250_set_termios(). Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping") Signed-off-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10vt: Disable KD_FONT_OP_COPYDaniel Vetter1-22/+2
commit 3c4e0dff2095c579b142d5a0693257f1c58b4804 upstream. It's buggy: On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote: > We recently discovered a slab-out-of-bounds read in fbcon in the latest > kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that > "fbcon_do_set_font" did not handle "vc->vc_font.data" and > "vc->vc_font.height" correctly, and the patch > <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this > issue. > > Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and > use KD_FONT_OP_SET again to set a large font.height for tty1. After that, > we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data > in "fbcon_do_set_font", while tty1 retains the original larger > height. Obviously, this will cause an out-of-bounds read, because we can > access a smaller vc_font.data with a larger vc_font.height. Further there was only one user ever. - Android's loadfont, busybox and console-tools only ever use OP_GET and OP_SET - fbset documentation only mentions the kernel cmdline font: option, not anything else. - systemd used OP_COPY before release 232 published in Nov 2016 Now unfortunately the crucial report seems to have gone down with gmane, and the commit message doesn't say much. But the pull request hints at OP_COPY being broken https://github.com/systemd/systemd/pull/3651 So in other words, this never worked, and the only project which foolishly every tried to use it, realized that rather quickly too. Instead of trying to fix security issues here on dead code by adding missing checks, fix the entire thing by removing the functionality. Note that systemd code using the OP_COPY function ignored the return value, so it doesn't matter what we're doing here really - just in case a lone server somewhere happens to be extremely unlucky and running an affected old version of systemd. The relevant code from font_copy_to_all_vcs() in systemd was: /* copy font from active VT, where the font was uploaded to */ cfo.op = KD_FONT_OP_COPY; cfo.height = vcs.v_active-1; /* tty1 == index 0 */ (void) ioctl(vcfd, KDFONTOP, &cfo); Note this just disables the ioctl, garbage collecting the now unused callbacks is left for -next. v2: Tetsuo found the old mail, which allowed me to find it on another archive. Add the link too. Acked-by: Peilin Ye <yepeilin.cs@gmail.com> Reported-by: Minh Yuan <yuanmingbuaa@gmail.com> References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html References: https://github.com/systemd/systemd/pull/3651 Cc: Greg KH <greg@kroah.com> Cc: Peilin Ye <yepeilin.cs@gmail.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10tty: make FONTX ioctl use the tty pointer they were actually passedLinus Torvalds1-15/+17
commit 90bfdeef83f1d6c696039b6a917190dcbbad3220 upstream. Some of the font tty ioctl's always used the current foreground VC for their operations. Don't do that then. This fixes a data race on fg_console. Side note: both Michael Ellerman and Jiri Slaby point out that all these ioctls are deprecated, and should probably have been removed long ago, and everything seems to be using the KDFONTOP ioctl instead. In fact, Michael points out that it looks like busybox's loadfont program seems to have switched over to using KDFONTOP exactly _because_ of this bug (ahem.. 12 years ago ;-). Reported-by: Minh Yuan <yuanmingbuaa@gmail.com> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Jiri Slaby <jirislaby@kernel.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10vt: keyboard, extend func_buf_lock to readersJiri Slaby1-4/+13
commit 82e61c3909db51d91b9d3e2071557b6435018b80 upstream. Both read-side users of func_table/func_buf need locking. Without that, one can easily confuse the code by repeatedly setting altering strings like: while (1) for (a = 0; a < 2; a++) { struct kbsentry kbs = {}; strcpy((char *)kbs.kb_string, a ? ".\n" : "88888\n"); ioctl(fd, KDSKBSENT, &kbs); } When that program runs, one can get unexpected output by holding F1 (note the unxpected period on the last line): . 88888 .8888 So protect all accesses to 'func_table' (and func_buf) by preexisting 'func_buf_lock'. It is easy in 'k_fn' handler as 'puts_queue' is expected not to sleep. On the other hand, KDGKBSENT needs a local (atomic) copy of the string because copy_to_user can sleep. Use already allocated, but unused 'kbs->kb_string' for that purpose. Note that the program above needs at least CAP_SYS_TTY_CONFIG. This depends on the previous patch and on the func_buf_lock lock added in commit 46ca3f735f34 (tty/vt: fix write/write race in ioctl(KDSKBSENT) handler) in 5.2. Likely fixes CVE-2020-25656. Cc: <stable@vger.kernel.org> Reported-by: Minh Yuan <yuanmingbuaa@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20201019085517.10176-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-11-10vt: keyboard, simplify vt_kdgkbsentJiri Slaby1-19/+9
commit 6ca03f90527e499dd5e32d6522909e2ad390896b upstream. Use 'strlen' of the string, add one for NUL terminator and simply do 'copy_to_user' instead of the explicit 'for' loop. This makes the KDGKBSENT case more compact. The only thing we need to take care about is NULL 'func_table[i]'. Use an empty string in that case. The original check for overflow could never trigger as the func_buf strings are always shorter or equal to 'struct kbsentry's. Cc: <stable@vger.kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20201019085517.10176-1-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-29tty: ipwireless: fix error handlingTong Zhang2-3/+3
[ Upstream commit db332356222d9429731ab9395c89cca403828460 ] ipwireless_send_packet() can only return 0 on success and -ENOMEM on error, the caller should check non zero for error condition Signed-off-by: Tong Zhang <ztong0001@gmail.com> Acked-by: David Sterba <dsterba@suse.com> Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29pty: do tty_flip_buffer_push without port->lock in pty_writeArtem Savkov1-1/+1
[ Upstream commit 71a174b39f10b4b93223d374722aa894b5d8a82e ] b6da31b2c07c "tty: Fix data race in tty_insert_flip_string_fixed_flag" puts tty_flip_buffer_push under port->lock introducing the following possible circular locking dependency: [30129.876566] ====================================================== [30129.876566] WARNING: possible circular locking dependency detected [30129.876567] 5.9.0-rc2+ #3 Tainted: G S W [30129.876568] ------------------------------------------------------ [30129.876568] sysrq.sh/1222 is trying to acquire lock: [30129.876569] ffffffff92c39480 (console_owner){....}-{0:0}, at: console_unlock+0x3fe/0xa90 [30129.876572] but task is already holding lock: [30129.876572] ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca [30129.876576] which lock already depends on the new lock. [30129.876577] the existing dependency chain (in reverse order) is: [30129.876578] -> #3 (&pool->lock/1){-.-.}-{2:2}: [30129.876581] _raw_spin_lock+0x30/0x70 [30129.876581] __queue_work+0x1a3/0x10f0 [30129.876582] queue_work_on+0x78/0x80 [30129.876582] pty_write+0x165/0x1e0 [30129.876583] n_tty_write+0x47f/0xf00 [30129.876583] tty_write+0x3d6/0x8d0 [30129.876584] vfs_write+0x1a8/0x650 [30129.876588] -> #2 (&port->lock#2){-.-.}-{2:2}: [30129.876590] _raw_spin_lock_irqsave+0x3b/0x80 [30129.876591] tty_port_tty_get+0x1d/0xb0 [30129.876592] tty_port_default_wakeup+0xb/0x30 [30129.876592] serial8250_tx_chars+0x3d6/0x970 [30129.876593] serial8250_handle_irq.part.12+0x216/0x380 [30129.876593] serial8250_default_handle_irq+0x82/0xe0 [30129.876594] serial8250_interrupt+0xdd/0x1b0 [30129.876595] __handle_irq_event_percpu+0xfc/0x850 [30129.876602] -> #1 (&port->lock){-.-.}-{2:2}: [30129.876605] _raw_spin_lock_irqsave+0x3b/0x80 [30129.876605] serial8250_console_write+0x12d/0x900 [30129.876606] console_unlock+0x679/0xa90 [30129.876606] register_console+0x371/0x6e0 [30129.876607] univ8250_console_init+0x24/0x27 [30129.876607] console_init+0x2f9/0x45e [30129.876609] -> #0 (console_owner){....}-{0:0}: [30129.876611] __lock_acquire+0x2f70/0x4e90 [30129.876612] lock_acquire+0x1ac/0xad0 [30129.876612] console_unlock+0x460/0xa90 [30129.876613] vprintk_emit+0x130/0x420 [30129.876613] printk+0x9f/0xc5 [30129.876614] show_pwq+0x154/0x618 [30129.876615] show_workqueue_state.cold.55+0x193/0x6ca [30129.876615] __handle_sysrq+0x244/0x460 [30129.876616] write_sysrq_trigger+0x48/0x4a [30129.876616] proc_reg_write+0x1a6/0x240 [30129.876617] vfs_write+0x1a8/0x650 [30129.876619] other info that might help us debug this: [30129.876620] Chain exists of: [30129.876621] console_owner --> &port->lock#2 --> &pool->lock/1 [30129.876625] Possible unsafe locking scenario: [30129.876626] CPU0 CPU1 [30129.876626] ---- ---- [30129.876627] lock(&pool->lock/1); [30129.876628] lock(&port->lock#2); [30129.876630] lock(&pool->lock/1); [30129.876631] lock(console_owner); [30129.876633] *** DEADLOCK *** [30129.876634] 5 locks held by sysrq.sh/1222: [30129.876634] #0: ffff8881d3ce0470 (sb_writers#3){.+.+}-{0:0}, at: vfs_write+0x359/0x650 [30129.876637] #1: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: __handle_sysrq+0x4d/0x460 [30129.876640] #2: ffffffff92c612c0 (rcu_read_lock){....}-{1:2}, at: show_workqueue_state+0x5/0xf0 [30129.876642] #3: ffff888107cb9018 (&pool->lock/1){-.-.}-{2:2}, at: show_workqueue_state.cold.55+0x15b/0x6ca [30129.876645] #4: ffffffff92c39980 (console_lock){+.+.}-{0:0}, at: vprintk_emit+0x123/0x420 [30129.876648] stack backtrace: [30129.876649] CPU: 3 PID: 1222 Comm: sysrq.sh Tainted: G S W 5.9.0-rc2+ #3 [30129.876649] Hardware name: Intel Corporation 2012 Client Platform/Emerald Lake 2, BIOS ACRVMBY1.86C.0078.P00.1201161002 01/16/2012 [30129.876650] Call Trace: [30129.876650] dump_stack+0x9d/0xe0 [30129.876651] check_noncircular+0x34f/0x410 [30129.876653] __lock_acquire+0x2f70/0x4e90 [30129.876656] lock_acquire+0x1ac/0xad0 [30129.876658] console_unlock+0x460/0xa90 [30129.876660] vprintk_emit+0x130/0x420 [30129.876660] printk+0x9f/0xc5 [30129.876661] show_pwq+0x154/0x618 [30129.876662] show_workqueue_state.cold.55+0x193/0x6ca [30129.876664] __handle_sysrq+0x244/0x460 [30129.876665] write_sysrq_trigger+0x48/0x4a [30129.876665] proc_reg_write+0x1a6/0x240 [30129.876666] vfs_write+0x1a8/0x650 It looks like the commit was aimed to protect tty_insert_flip_string and there is no need for tty_flip_buffer_push to be under this lock. Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag") Signed-off-by: Artem Savkov <asavkov@redhat.com> Acked-by: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20200902120045.3693075-1-asavkov@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29tty: hvcs: Don't NULL tty->driver_data until hvcs_cleanup()Tyrel Datwyler1-7/+7
[ Upstream commit 63ffcbdad738e3d1c857027789a2273df3337624 ] The code currently NULLs tty->driver_data in hvcs_close() with the intent of informing the next call to hvcs_open() that device needs to be reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from tty->driver_data which was previoulsy NULLed by hvcs_close() and our call to tty_port_put(&hvcsd->port) doesn't actually do anything since &hvcsd->port ends up translating to NULL by chance. This has the side effect that when hvcs_remove() is called we have one too many port references preventing hvcs_destuct_port() from ever being called. This also prevents us from reusing the /dev/hvcsX node in a future hvcs_probe() and we can eventually run out of /dev/hvcsX devices. Fix this by waiting to NULL tty->driver_data in hvcs_cleanup(). Fixes: 27bf7c43a19c ("TTY: hvcs, add tty install") Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com> Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-29tty: serial: earlycon dependencyTong Zhang1-0/+1
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ] parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON should automatically select SERIAL_CORE, otherwise will result in symbol not found error during linking if SERIAL_CORE is not configured as builtin Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon") Signed-off-by: Tong Zhang <ztong0001@gmail.com> Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01tty: serial: samsung: Correct clock selection logicJonathan Bakker1-4/+4
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ] Some variants of the samsung tty driver can pick which clock to use for their baud rate generation. In the DT conversion, a default clock was selected to be used if a specific one wasn't assigned and then a comparison of which clock rate worked better was done. Unfortunately, the comparison was implemented in such a way that only the default clock was ever actually compared. Fix this by iterating through all possible clocks, except when a specific clock has already been picked via clk_sel (which is only possible via board files). Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250: 8250_omap: Terminate DMA before pushing data on RX timeoutVignesh Raghavendra1-2/+4
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ] Terminate and flush DMA internal buffers, before pushing RX data to higher layer. Otherwise, this will lead to data corruption, as driver would end up pushing stale buffer data to higher layer while actual data is still stuck inside DMA hardware and has yet not arrived at the memory. While at that, replace deprecated dmaengine_terminate_all() with dmaengine_terminate_async(). Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250_omap: Fix sleeping function called from invalid context during ↵Peter Ujfalusi1-1/+1
probe [ Upstream commit 4ce35a3617c0ac758c61122b2218b6c8c9ac9398 ] When booting j721e the following bug is printed: [ 1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99 [ 1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1 [ 1.154832] 3 locks held by kworker/0:1/12: [ 1.154836] #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154852] #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8 [ 1.154860] #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138 [ 1.154872] irq event stamp: 63096 [ 1.154881] hardirqs last enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78 [ 1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80 [ 1.154893] softirqs last enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564 [ 1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140 [ 1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221 [ 1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT) [ 1.154917] Workqueue: events deferred_probe_work_func [ 1.154923] Call trace: [ 1.154928] dump_backtrace+0x0/0x190 [ 1.154933] show_stack+0x14/0x20 [ 1.154940] dump_stack+0xe0/0x148 [ 1.154946] ___might_sleep+0x150/0x1f0 [ 1.154952] __might_sleep+0x4c/0x80 [ 1.154957] wait_for_completion_timeout+0x40/0x140 [ 1.154964] ti_sci_set_device_state+0xa0/0x158 [ 1.154969] ti_sci_cmd_get_device_exclusive+0x14/0x20 [ 1.154977] ti_sci_dev_start+0x34/0x50 [ 1.154984] genpd_runtime_resume+0x78/0x1f8 [ 1.154991] __rpm_callback+0x3c/0x140 [ 1.154996] rpm_callback+0x20/0x80 [ 1.155001] rpm_resume+0x568/0x758 [ 1.155007] __pm_runtime_resume+0x44/0xb0 [ 1.155013] omap8250_probe+0x2b4/0x508 [ 1.155019] platform_drv_probe+0x50/0xa0 [ 1.155023] really_probe+0xd4/0x318 [ 1.155028] driver_probe_device+0x54/0xe8 [ 1.155033] __device_attach_driver+0x80/0xb8 [ 1.155039] bus_for_each_drv+0x74/0xc0 [ 1.155044] __device_attach+0xdc/0x138 [ 1.155049] device_initial_probe+0x10/0x18 [ 1.155053] bus_probe_device+0x98/0xa0 [ 1.155058] deferred_probe_work_func+0x74/0xb0 [ 1.155063] process_one_work+0x280/0x6e8 [ 1.155068] worker_thread+0x48/0x430 [ 1.155073] kthread+0x108/0x138 [ 1.155079] ret_from_fork+0x10/0x18 To fix the bug we need to first call pm_runtime_enable() prior to any pm_runtime calls. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250_port: Don't service RX FIFO if throttledVignesh Raghavendra1-1/+15
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ] When port's throttle callback is called, it should stop pushing any more data into TTY buffer to avoid buffer overflow. This means driver has to stop HW from receiving more data and assert the HW flow control. For UARTs with auto HW flow control (such as 8250_omap) manual assertion of flow control line is not possible and only way is to allow RX FIFO to fill up, thus trigger auto HW flow control logic. Therefore make sure that 8250 generic IRQ handler does not drain data when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not servicing, RX FIFO would trigger auto HW flow control when FIFO occupancy reaches preset threshold, thus halting RX. Since, error conditions in UART_LSR register are cleared just by reading the register, data has to be drained in case there are FIFO errors, else error information will lost. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2020-10-01serial: 8250: Avoid error message on reprobeLukas Wunner1-2/+9
commit e0a851fe6b9b619527bd928aa93caaddd003f70c upstream. If the call to uart_add_one_port() in serial8250_register_8250_port() fails, a half-initialized entry in the serial_8250ports[] array is left behind. A subsequent reprobe of the same serial port causes that entry to be reused. Because uart->port.dev is set, uart_remove_one_port() is called for the half-initialized entry and bails out with an error message: bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval) The same happens on failure of mctrl_gpio_init() since commit 4a96895f74c9 ("tty/serial/8250: use mctrl_gpio helpers"). Fix by zeroing the uart->port.dev pointer in the probe error path. The bug was introduced in v2.6.10 by historical commit befff6f5bf5f ("[SERIAL] Add new port registration/unregistration functions."): https://git.kernel.org/tglx/history/c/befff6f5bf5f The commit added an unconditional call to uart_remove_one_port() in serial8250_register_port(). In v3.7, commit 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe") made that call conditional on uart->port.dev which allows me to fix the issue by zeroing that pointer in the error path. Thus, the present commit will fix the problem as far back as v3.7 whereas still older versions need to also cherry-pick 835d844d1a28. Fixes: 835d844d1a28 ("8250_pnp: do pnp probe before legacy probe") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v2.6.10 Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de [iwamatsu: Backported to 4.4, 4.9: adjust context] Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-23serial: 8250_pci: Add Realtek 816a and 816bTobias Diedrich1-0/+11
commit 3c5a87be170aba8ac40982182f812dcff6ed1ad1 upstream. These serial ports are exposed by the OOB-management-engine on RealManage-enabled network cards (e.g. AMD DASH enabled systems using Realtek cards). Because these have 3 BARs, they fail the "num_iomem <= 1" check in serial_pci_guess_board. I've manually checked the two IOMEM regions and BAR 2 doesn't seem to respond to reads, but BAR 4 seems to be an MMIO version of the IO ports (untested). With this change, the ports are detected: 0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A 0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A lspci output: 02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550]) Subsystem: 17aa:5082 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 82 IOMMU group: 11 Region 0: I/O ports at 2200 [size=256] Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K] Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 01 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s (ok), Width x1 (ok) TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+ 10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix- EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit- FRS- TPHComp- ExtTPHComp- AtomicOpsCap: 32bit- 64bit- 128bitCAS- DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled, AtomicOpsCtl: ReqEn- LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1- EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest- Retimer- 2Retimers- CrosslinkRes: unsupported Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Vector table: BAR=4 offset=00000000 PBA: BAR=4 offset=00000800 Capabilities: [d0] Vital Product Data Not readable Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+ AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn- MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap- HeaderLog: 00000000 00000000 00000000 00000000 Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [170 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [178 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=150us PortTPowerOnTime=150us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us 02:00.2 0700: 10ec:816b (rev 0e) [...same...] Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: 8250: change lock order in serial8250_do_startup()Sergey Senozhatsky1-3/+6
commit 205d300aea75623e1ae4aa43e0d265ab9cf195fd upstream. We have a number of "uart.port->desc.lock vs desc.lock->uart.port" lockdep reports coming from 8250 driver; this causes a bit of trouble to people, so let's fix it. The problem is reverse lock order in two different call paths: chain #1: serial8250_do_startup() spin_lock_irqsave(&port->lock); disable_irq_nosync(port->irq); raw_spin_lock_irqsave(&desc->lock) chain #2: __report_bad_irq() raw_spin_lock_irqsave(&desc->lock) for_each_action_of_desc() printk() spin_lock_irqsave(&port->lock); Fix this by changing the order of locks in serial8250_do_startup(): do disable_irq_nosync() first, which grabs desc->lock, and grab uart->port after that, so that chain #1 and chain #2 have same lock order. Full lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 5.4.39 #55 Not tainted ====================================================== swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57 but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&irq_desc_lock_class){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d __irq_get_desc_lock+0x65/0x89 __disable_irq_nosync+0x3b/0x93 serial8250_do_startup+0x451/0x75c uart_startup+0x1b4/0x2ff uart_port_activate+0x73/0xa0 tty_port_open+0xae/0x10a uart_open+0x1b/0x26 tty_open+0x24d/0x3a0 chrdev_open+0xd5/0x1cc do_dentry_open+0x299/0x3c8 path_openat+0x434/0x1100 do_filp_open+0x9b/0x10a do_sys_open+0x15f/0x3d7 kernel_init_freeable+0x157/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #1 (&port_lock_key){-.-.}: _raw_spin_lock_irqsave+0x61/0x8d serial8250_console_write+0xa7/0x2a0 console_unlock+0x3b7/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 register_console+0x336/0x3a4 uart_add_one_port+0x51b/0x5be serial8250_register_8250_port+0x454/0x55e dw8250_probe+0x4dc/0x5b9 platform_drv_probe+0x67/0x8b really_probe+0x14a/0x422 driver_probe_device+0x66/0x130 device_driver_attach+0x42/0x5b __driver_attach+0xca/0x139 bus_for_each_dev+0x97/0xc9 bus_add_driver+0x12b/0x228 driver_register+0x64/0xed do_one_initcall+0x20c/0x4a6 do_initcall_level+0xb5/0xc5 do_basic_setup+0x4c/0x58 kernel_init_freeable+0x13f/0x1dd kernel_init+0xe/0x105 ret_from_fork+0x27/0x50 -> #0 (console_owner){-...}: __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 console_lock_spinning_enable+0x51/0x57 console_unlock+0x25d/0x528 vprintk_emit+0x111/0x17f printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 ret_from_intr+0x0/0x1d cpuidle_enter_state+0x12f/0x1fd cpuidle_enter+0x2e/0x3d do_idle+0x1ce/0x2ce cpu_startup_entry+0x1d/0x1f start_kernel+0x406/0x46a secondary_startup_64+0xa4/0xb0 other info that might help us debug this: Chain exists of: console_owner --> &port_lock_key --> &irq_desc_lock_class Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&irq_desc_lock_class); lock(&port_lock_key); lock(&irq_desc_lock_class); lock(console_owner); *** DEADLOCK *** 2 locks held by swapper/0/0: #0: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba #1: ffffffffab65b5c0 (console_lock){+.+.}, at: console_trylock_spinning+0x20/0x181 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.39 #55 Hardware name: XXXXXX Call Trace: <IRQ> dump_stack+0xbf/0x133 ? print_circular_bug+0xd6/0xe9 check_noncircular+0x1b9/0x1c3 __lock_acquire+0x118d/0x2714 lock_acquire+0x203/0x258 ? console_lock_spinning_enable+0x31/0x57 console_lock_spinning_enable+0x51/0x57 ? console_lock_spinning_enable+0x31/0x57 console_unlock+0x25d/0x528 ? console_trylock+0x18/0x4e vprintk_emit+0x111/0x17f ? lock_acquire+0x203/0x258 printk+0x59/0x73 __report_bad_irq+0xa3/0xba note_interrupt+0x19a/0x1d6 handle_irq_event_percpu+0x57/0x79 handle_irq_event+0x36/0x55 handle_fasteoi_irq+0xc2/0x18a do_IRQ+0xb3/0x157 common_interrupt+0xf/0xf </IRQ> Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Fixes: 768aec0b5bcc ("serial: 8250: fix shared interrupts issues with SMP and RT kernels") Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Raul Rangel <rrangel@google.com> BugLink: https://bugs.chromium.org/p/chromium/issues/detail?id=1114800 Link: https://lore.kernel.org/lkml/CAHQZ30BnfX+gxjPm1DUd5psOTqbyDh4EJE=2=VAMW_VDafctkA@mail.gmail.com/T/#u Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200817022646.1484638-1-sergey.senozhatsky@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: pl011: Don't leak amba_ports entry on driver register errorLukas Wunner1-1/+4
commit 89efbe70b27dd325d8a8c177743a26b885f7faec upstream. pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry, then calls pl011_register_port() to register the uart driver with the tty layer. If registration of the uart driver fails, the amba_ports[] entry is not released. If this happens 14 times (value of UART_NR macro), then all amba_ports[] entries will have been leaked and driver probing is no longer possible. (To be fair, that can only happen if the DeviceTree doesn't contain alias IDs since they cause the same entry to be used for a given port.) Fix it. Fixes: ef2889f7ffee ("serial: pl011: Move uart_register_driver call to device") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.15+ Cc: Tushar Behera <tushar.behera@linaro.org> Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: pl011: Fix oops on -EPROBE_DEFERLukas Wunner1-6/+5
commit 27afac93e3bd7fa89749cf11da5d86ac9cde4dba upstream. If probing of a pl011 gets deferred until after free_initmem(), an oops ensues because pl011_console_match() is called which has been freed. Fix by removing the __init attribute from the function and those it calls. Commit 10879ae5f12e ("serial: pl011: add console matching function") introduced pl011_console_match() not just for early consoles but regular preferred consoles, such as those added by acpi_parse_spcr(). Regular consoles may be registered after free_initmem() for various reasons, one being deferred probing, another being dynamic enablement of serial ports using a DeviceTree overlay. Thus, pl011_console_match() must not be declared __init and the functions it calls mustn't either. Stack trace for posterity: Unable to handle kernel paging request at virtual address 80c38b58 Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM PC is at pl011_console_match+0x0/0xfc LR is at register_console+0x150/0x468 [<80187004>] (register_console) [<805a8184>] (uart_add_one_port) [<805b2b68>] (pl011_register_port) [<805b3ce4>] (pl011_probe) [<80569214>] (amba_probe) [<805ca088>] (really_probe) [<805ca2ec>] (driver_probe_device) [<805ca5b0>] (__device_attach_driver) [<805c8060>] (bus_for_each_drv) [<805c9dfc>] (__device_attach) [<805ca630>] (device_initial_probe) [<805c90a8>] (bus_probe_device) [<805c95a8>] (deferred_probe_work_func) Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03serial: samsung: Removes the IRQ not found warningTamseel Shams1-3/+5
commit 8c6c378b0cbe0c9f1390986b5f8ffb5f6ff7593b upstream. In few older Samsung SoCs like s3c2410, s3c2412 and s3c2440, UART IP is having 2 interrupt lines. However, in other SoCs like s3c6400, s5pv210, exynos5433, and exynos4210 UART is having only 1 interrupt line. Due to this, "platform_get_irq(platdev, 1)" call in the driver gives the following false-positive error: "IRQ index 1 not found" on newer SoC's. This patch adds the condition to check for Tx interrupt only for the those SoC's which have 2 interrupt lines. Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()George Kennedy1-1/+11
commit bc5269ca765057a1b762e79a1cfd267cd7bf1c46 upstream. vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl to save struct vc_data values that are modified and restore the original values in case of error. Signed-off-by: George Kennedy <george.kennedy@oracle.com> Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+38a3699c7eaf165b97a6@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/1596213192-6635-2-git-send-email-george.kennedy@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-03vt: defer kfree() of vc_screenbuf in vc_do_resize()Tetsuo Handa1-2/+3
commit f8d1653daec02315e06d30246cff4af72e76e54e upstream. syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin(). Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access vc->vc_pos when scroll is involved in order to manipulate cursor, but vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets updated based on the result of vc->vc_sw->con_set_origin(). Preserving old buffer and tolerating outdated vc members until set_origin() completes would be easier than preventing vc->vc_sw->con_set_origin() from accessing outdated vc members. [1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3 Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31vt: Reject zero-sized screen buffer size.Tetsuo Handa1-11/+18
commit ce684552a266cb1c7cc2f7e623f38567adec6653 upstream. syzbot is reporting general protection fault in do_con_write() [1] caused by vc->vc_screenbuf == ZERO_SIZE_PTR caused by vc->vc_screenbuf_size == 0 caused by vc->vc_cols == vc->vc_rows == vc->vc_size_row == 0 caused by fb_set_var() from ioctl(FBIOPUT_VSCREENINFO) on /dev/fb0 , for gotoxy(vc, 0, 0) from reset_terminal() from vc_init() from vc_allocate() from con_install() from tty_init_dev() from tty_open() on such console causes vc->vc_pos == 0x10000000e due to ((unsigned long) ZERO_SIZE_PTR) + -1U * 0 + (-1U << 1). I don't think that a console with 0 column or 0 row makes sense. And it seems that vc_do_resize() does not intend to allow resizing a console to 0 column or 0 row due to new_cols = (cols ? cols : vc->vc_cols); new_rows = (lines ? lines : vc->vc_rows); exception. Theoretically, cols and rows can be any range as long as 0 < cols * rows * 2 <= KMALLOC_MAX_SIZE is satisfied (e.g. cols == 1048576 && rows == 2 is possible) because of vc->vc_size_row = vc->vc_cols << 1; vc->vc_screenbuf_size = vc->vc_rows * vc->vc_size_row; in visual_init() and kzalloc(vc->vc_screenbuf_size) in vc_allocate(). Since we can detect cols == 0 or rows == 0 via screenbuf_size = 0 in visual_init(), we can reject kzalloc(0). Then, vc_allocate() will return an error, and con_write() will not be called on a console with 0 column or 0 row. We need to make sure that integer overflow in visual_init() won't happen. Since vc_do_resize() restricts cols <= 32767 and rows <= 32767, applying 1 <= cols <= 32767 and 1 <= rows <= 32767 restrictions to vc_allocate() will be practically fine. This patch does not touch con_init(), for returning -EINVAL there does not help when we are not returning -ENOMEM. [1] https://syzkaller.appspot.com/bug?extid=017265e8553724e514e8 Reported-and-tested-by: syzbot <syzbot+017265e8553724e514e8@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200712111013.11881-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250_mtk: Fix high-speed baud rates clampingSerge Semin1-0/+18
commit 551e553f0d4ab623e2a6f424ab5834f9c7b5229c upstream. Commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") fixed limits of a baud rate setting for a generic 8250 port. In other words since that commit the baud rate has been permitted to be within [uartclk / 16 / UART_DIV_MAX; uartclk / 16], which is absolutely normal for a standard 8250 UART port. But there are custom 8250 ports, which provide extended baud rate limits. In particular the Mediatek 8250 port can work with baud rates up to "uartclk" speed. Normally that and any other peculiarity is supposed to be handled in a custom set_termios() callback implemented in the vendor-specific 8250-port glue-driver. Currently that is how it's done for the most of the vendor-specific 8250 ports, but for some reason for Mediatek a solution has been spread out to both the glue-driver and to the generic 8250-port code. Due to that a bug has been introduced, which permitted the extended baud rate limit for all even for standard 8250-ports. The bug has been fixed by the commit 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") by narrowing the baud rates limit back down to the normal bounds. Unfortunately by doing so we also broke the Mediatek-specific extended bauds feature. A fix of the problem described above is twofold. First since we can't get back the extended baud rate limits feature to the generic set_termios() function and that method supports only a standard baud rates range, the requested baud rate must be locally stored before calling it and then restored back to the new termios structure after the generic set_termios() finished its magic business. By doing so we still use the serial8250_do_set_termios() method to set the LCR/MCR/FCR/etc. registers, while the extended baud rate setting procedure will be performed later in the custom Mediatek-specific set_termios() callback. Second since a true baud rate is now fully calculated in the custom set_termios() method we need to locally update the port timeout by calling the uart_update_timeout() function. After the fixes described above are implemented in the 8250_mtk.c driver, the Mediatek 8250-port should get back to normally working with extended baud rates. Link: https://lore.kernel.org/linux-serial/20200701211337.3027448-1-danielwinkler@google.com Fixes: 7b668c064ec3 ("serial: 8250: Fix max baud limit in generic 8250 port") Reported-by: Daniel Winkler <danielwinkler@google.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: stable <stable@vger.kernel.org> Tested-by: Claire Chang <tientzu@chromium.org> Link: https://lore.kernel.org/r/20200714124113.20918-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-07-31serial: 8250: fix null-ptr-deref in serial8250_start_tx()Yang Yingliang1-1/+1
commit f4c23a140d80ef5e6d3d1f8f57007649014b60fa upstream. I got null-ptr-deref in serial8250_start_tx(): [ 78.114630] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 [ 78.123778] Mem abort info: [ 78.126560] ESR = 0x86000007 [ 78.129603] EC = 0x21: IABT (current EL), IL = 32 bits [ 78.134891] SET = 0, FnV = 0 [ 78.137933] EA = 0, S1PTW = 0 [ 78.141064] user pgtable: 64k pages, 48-bit VAs, pgdp=00000027d41a8600 [ 78.147562] [0000000000000000] pgd=00000027893f0003, p4d=00000027893f0003, pud=00000027893f0003, pmd=00000027c9a20003, pte=0000000000000000 [ 78.160029] Internal error: Oops: 86000007 [#1] SMP [ 78.164886] Modules linked in: sunrpc vfat fat aes_ce_blk crypto_simd cryptd aes_ce_cipher crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce ses enclosure sg sbsa_gwdt ipmi_ssif spi_dw_mmio sch_fq_codel vhost_net tun vhost vhost_iotlb tap ip_tables ext4 mbcache jbd2 ahci hisi_sas_v3_hw libahci hisi_sas_main libsas hns3 scsi_transport_sas hclge libata megaraid_sas ipmi_si hnae3 ipmi_devintf ipmi_msghandler br_netfilter bridge stp llc nvme nvme_core xt_sctp sctp libcrc32c dm_mod nbd [ 78.207383] CPU: 11 PID: 23258 Comm: null-ptr Not tainted 5.8.0-rc6+ #48 [ 78.214056] Hardware name: Huawei TaiShan 2280 V2/BC82AMDC, BIOS 2280-V2 CS V3.B210.01 03/12/2020 [ 78.222888] pstate: 80400089 (Nzcv daIf +PAN -UAO BTYPE=--) [ 78.228435] pc : 0x0 [ 78.230618] lr : serial8250_start_tx+0x160/0x260 [ 78.235215] sp : ffff800062eefb80 [ 78.238517] x29: ffff800062eefb80 x28: 0000000000000fff [ 78.243807] x27: ffff800062eefd80 x26: ffff202fd83b3000 [ 78.249098] x25: ffff800062eefd80 x24: ffff202fd83b3000 [ 78.254388] x23: ffff002fc5e50be8 x22: 0000000000000002 [ 78.259679] x21: 0000000000000001 x20: 0000000000000000 [ 78.264969] x19: ffffa688827eecc8 x18: 0000000000000000 [ 78.270259] x17: 0000000000000000 x16: 0000000000000000 [ 78.275550] x15: ffffa68881bc67a8 x14: 00000000000002e6 [ 78.280841] x13: ffffa68881bc67a8 x12: 000000000000c539 [ 78.286131] x11: d37a6f4de9bd37a7 x10: ffffa68881cccff0 [ 78.291421] x9 : ffffa68881bc6000 x8 : ffffa688819daa88 [ 78.296711] x7 : ffffa688822a0f20 x6 : ffffa688819e0000 [ 78.302002] x5 : ffff800062eef9d0 x4 : ffffa68881e707a8 [ 78.307292] x3 : 0000000000000000 x2 : 0000000000000002 [ 78.312582] x1 : 0000000000000001 x0 : ffffa688827eecc8 [ 78.317873] Call trace: [ 78.320312] 0x0 [ 78.322147] __uart_start.isra.9+0x64/0x78 [ 78.326229] uart_start+0xb8/0x1c8 [ 78.329620] uart_flush_chars+0x24/0x30 [ 78.333442] n_tty_receive_buf_common+0x7b0/0xc30 [ 78.338128] n_tty_receive_buf+0x44/0x2c8 [ 78.342122] tty_ioctl+0x348/0x11f8 [ 78.345599] ksys_ioctl+0xd8/0xf8 [ 78.348903] __arm64_sys_ioctl+0x2c/0xc8 [ 78.352812] el0_svc_common.constprop.2+0x88/0x1b0 [ 78.357583] do_el0_svc+0x44/0xd0 [ 78.360887] el0_sync_handler+0x14c/0x1d0 [ 78.364880] el0_sync+0x140/0x180 [ 78.368185] Code: bad PC value SERIAL_PORT_DFNS is not defined on each arch, if it's not defined, serial8250_set_defaults() won't be called in serial8250_isa_init_ports(), so the p->serial_in pointer won't be initialized, and it leads a null-ptr-deref. Fix this problem by calling serial8250_set_defaults() after init uart port. Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200721143852.4058352-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-30Revert "tty: hvc: Fix data abort due to race in hvc_open"Greg Kroah-Hartman1-14/+2
commit cf9c94456ebafc6d75a834e58dfdc8ae71a3acbc upstream. This reverts commit e2bd1dcbe1aa34ff5570b3427c530e4332ecf0fe. In discussion on the mailing list, it has been determined that this is not the correct type of fix for this issue. Revert it so that we can do this correctly. Reported-by: Jiri Slaby <jslaby@suse.cz> Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org Cc: Raghavendra Rao Ananta <rananta@codeaur