| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 9eff2b2e59fda25051ab36cd1cb5014661df657b ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211011134920.118477-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b7a0a63f3fed57d413bb857de164ea9c3984bc4e ]
Calling tps6598x_block_read with a higher than allowed len can be
handled by just returning an error. There's no need to crash systems
with panic-on-warn enabled.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20210914140235.65955-3-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 14651496a3de6807a17c310f63c894ea0c5d858e ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210915034925.2399823-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1ad707f559f7cb12c64f3d7cb37f0b1ea27c1058 ]
If role is changed without the "none" step, A- and B- valid session could
be set at the same time. It is an issue.
This patch resets A-session if role switch sets B-session, and resets
B-session if role switch sets A-session.
Then, it is possible to change the role without the "none" step.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-4-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d387f61b0240854e81450c261beb775065bad5d ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b2cab2a24fb5d13ce1d384ecfb6de827fa08a048 ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8ef1e58783b9f55daa4a865c7801dc75cbeb8260 ]
REGMAP_I2C is not a user visible kconfig symbol so driver configs
should not "depend on" it. They should depend on I2C and then
select REGMAP_I2C.
If this worked, it was only because some other driver had set/enabled
REGMAP_I2C.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20211015013609.7300-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fde1fbedbaed4e76cef4600d775b185f59b9b568 ]
The kconfig symbol GENERIC_PHY says:
All the users of this framework should select this config.
and around 136 out of 138 drivers do so, so change USB_MUSB_MEDIATEK
to do so also.
This (also) fixes a long circular dependency problem for an upcoming
patch.
Fixes: 0990366bab3c ("usb: musb: Add support for MediaTek musb controller")
Cc: Bin Liu <b-liu@ti.com>
Cc: Min Guo <min.guo@mediatek.com>
Cc: Yonglong Wu <yonglong.wu@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20211005235747.5588-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68e7c510fdf4f6167404609da52e1979165649f6 ]
Return an error code if usb_get_function() fails. Don't return success.
Fixes: 4bc8a33f2407 ("usb: gadget: hid: convert to new interface of f_hid")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211011123739.GC15188@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9aaa81c3366e8393a62374e3a1c67c69edc07b8a upstream.
Chipidea core was calling the interrupt handler from non-IRQ context
with interrupts enabled, something which can lead to a deadlock if
there's an actual interrupt trying to take a lock that's already held
(e.g. the controller lock in udc_irq()).
Add a wrapper that can be used to fake interrupts instead of calling the
handler directly.
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Fixes: 876d4e1e8298 ("usb: chipidea: core: add wakeup support for extcon")
Cc: Peter Chen <peter.chen@kernel.org>
Cc: stable@vger.kernel.org # 4.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211021083447.20078-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79a4479a17b83310deb0b1a2a274fe5be12d2318 upstream.
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Use the common control-message timeout define for the five-second
timeout and drop the driver-specific one.
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Cc: stable@vger.kernel.org # 2.6.21
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211025115159.4954-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 910c996335c37552ee30fcb837375b808bb4f33b upstream.
I got memory leak as follows when doing fault injection test:
unreferenced object 0xffff888258228440 (size 64):
comm "kworker/7:2", pid 2005, jiffies 4294989509 (age 824.540s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8167939c>] slab_post_alloc_hook+0x9c/0x490
[<ffffffff8167f627>] kmem_cache_alloc_trace+0x1f7/0x470
[<ffffffffa02ac0e4>] keyspan_port_probe+0xa4/0x5d0 [keyspan]
[<ffffffffa0294c07>] usb_serial_device_probe+0x97/0x1d0 [usbserial]
[<ffffffff82b50ca7>] really_probe+0x167/0x460
[<ffffffff82b51099>] __driver_probe_device+0xf9/0x180
[<ffffffff82b51173>] driver_probe_device+0x53/0x130
[<ffffffff82b516f5>] __device_attach_driver+0x105/0x130
[<ffffffff82b4cfe9>] bus_for_each_drv+0x129/0x190
[<ffffffff82b50a69>] __device_attach+0x1c9/0x270
[<ffffffff82b518d0>] device_initial_probe+0x20/0x30
[<ffffffff82b4f062>] bus_probe_device+0x142/0x160
[<ffffffff82b4a4e9>] device_add+0x829/0x1300
[<ffffffffa0295fda>] usb_serial_probe.cold+0xc9b/0x14ac [usbserial]
[<ffffffffa02266aa>] usb_probe_interface+0x1aa/0x3c0 [usbcore]
[<ffffffff82b50ca7>] really_probe+0x167/0x460
If keyspan_port_probe() fails to allocate memory for an out_buffer[i] or
in_buffer[i], the previously allocated memory for out_buffer or
in_buffer needs to be freed on the error handling path, otherwise a
memory leak will result.
Fixes: bad41a5bf177 ("USB: keyspan: fix port DMA-buffer allocations")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20211015085543.1203011-1-wanghai38@huawei.com
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 660a92a59b9e831a0407e41ff62875656d30006e upstream.
AMD's Yellow Carp platform supports runtime power management for
XHCI Controllers, so enable the same by default for all XHCI Controllers.
[ regrouped and aligned the PCI_DEVICE_ID definitions -Mathias]
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211014121200.75433-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e1959faf085b004e6c3afaaaa743381f00e7c015 upstream.
Some USB 3.1 enumeration issues were reported after the hub driver removed
the minimum 100ms limit for the power-on-good delay.
Since commit 90d28fb53d4a ("usb: core: reduce power-on-good delay time of
root hub") the hub driver sets the power-on-delay based on the
bPwrOn2PwrGood value in the hub descriptor.
xhci driver has a 20ms bPwrOn2PwrGood value for both roothubs based
on xhci spec section 5.4.8, but it's clearly not enough for the
USB 3.1 devices, causing enumeration issues.
Tests indicate full 100ms delay is needed.
Reported-by: Walt Jr. Brake <mr.yming81@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: 90d28fb53d4a ("usb: core: reduce power-on-good delay time of root hub")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211105160036.549516-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05c8f1b67e67dcd786ae3fe44492bbc617b4bd12 upstream.
These drive enclosures have firmware bugs that make it impossible to mount
a new virtual ISO image after Linux ejects the old one if the device is
locked by Linux. Windows bypasses this problem by the fact that they do
not lock the device. Add a quirk to disable device locking for these
drive enclosures.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Buren <braewoods+lkml@braewoods.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211014015504.2695089-1-braewoods+lkml@braewoods.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21b5fcdccb32ff09b6b63d4a83c037150665a83f upstream.
musb_gadget_queue() adds the passed request to musb_ep::req_list. If the
endpoint is idle and it is the first request then it invokes
musb_queue_resume_work(). If the function returns an error then the
error is passed to the caller without any clean-up and the request
remains enqueued on the list. If the caller enqueues the request again
then the list corrupts.
Remove the request from the list on error.
Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Viraj Shah <viraj.shah@linutronix.de>
Link: https://lore.kernel.org/r/20211021093644.4734-1-viraj.shah@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a0548b26901f082684ad1fb3ba397d2de3a1406a upstream.
On 64-bit:
drivers/usb/gadget/udc/fsl_qe_udc.c: In function ‘qe_ep0_rx’:
drivers/usb/gadget/udc/fsl_qe_udc.c:842:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
842 | vaddr = (u32)phys_to_virt(in_be32(&bd->buf));
| ^
In file included from drivers/usb/gadget/udc/fsl_qe_udc.c:41:
drivers/usb/gadget/udc/fsl_qe_udc.c:843:28: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
843 | frame_set_data(pframe, (u8 *)vaddr);
| ^
The driver assumes physical and virtual addresses are 32-bit, hence it
cannot work on 64-bit platforms.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20211027080849.3276289-1-geert@linux-m68k.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f2d73788d9067fd4f677ac5f60ffd25945af7af upstream.
For Aspeed, HCHalted status depends on not only Run/Stop but also
ASS/PSS status.
Handshake CMD_RUN on startup instead.
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Link: https://lore.kernel.org/r/20210910073619.26095-1-neal_liu@aspeedtech.com
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit d58fc9e9c15825e3a8fc1ef3b52495c93c41e71c which is
commit 58877b0824da15698bd85a0a9dbfa8c354e6ecb7 upstream.
It has been reported to be causing problems in Arch and Fedora bug
reports.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://bbs.archlinux.org/viewtopic.php?pid=2000956#p2000956
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019542
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019576
Link: https://lore.kernel.org/r/42bcbea6-5eb8-16c7-336a-2cb72e71bc36@redhat.com
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Chris Chiu <chris.chiu@canonical.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0ea9ac731a315cd10bd6d6b33817b68ca9111ecf which is
commit b7a0a792f864583207c593b50fd1b752ed89f4c1 upstream.
It has been reported to be causing problems in Arch and Fedora bug
reports.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://bbs.archlinux.org/viewtopic.php?pid=2000956#p2000956
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019542
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2019576
Link: https://lore.kernel.org/r/42bcbea6-5eb8-16c7-336a-2cb72e71bc36@redhat.com
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: Chris Chiu <chris.chiu@canonical.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5255660b208aebfdb71d574f3952cf48392f4306 upstream.
Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints
at least, if the xHC halts on a particular TRB due to an error then
the DCS field in the Out Endpoint Context maintained by the hardware
is not updated with the current cycle state.
Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit
from the TRB that the xHC stopped on.
[ bjorn: rebased to v5.14-rc2 ]
Link: https://github.com/raspberrypi/linux/issues/3060
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c184accc4a42c7872dc8e8d0fc97a740dc61fe24 upstream.
Adding support for Quectel EG91 LTE module.
The interface layout is same as for EG95.
usb-devices output:
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0191 Rev=03.18
S: Manufacturer=Android
S: Product=Android
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
Interfaces:
0: Diag
1: GNSS
2: AT-command interface/modem
3: Modem
4: QMI
Signed-off-by: Tomaz Solc <tomaz.solc@tablix.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5a8a07edafed8bede17a95ef8940fe3a57a77d5 upstream.
Add the following Telit LE910Cx composition:
0x1204: tty, adb, mbim, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20211004105655.8515-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2263eb7370060bdb0013bc14e1a7c9bf33617a55 upstream.
Add usb product id of the Quectel EC200S-CN module.
usb-devices output for 0x6002:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=6002 Rev=03.18
S: Manufacturer=Android
S: Product=Android
S: SerialNumber=0000
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Link: https://lore.kernel.org/r/20210930021112.330396-1-mtwget@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11c52d250b34a0862edc29db03fbec23b30db6da upstream.
When the module boots into QDL download mode it exposes the 1199:90d2
ids, which can be mapped to the qcserial driver, and used to run
firmware upgrades (e.g. with the qmi-firmware-update program).
T: Bus=01 Lev=03 Prnt=08 Port=03 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=90d2 Rev=00.00
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=Sierra Wireless EM9191
S: SerialNumber=8W0382004102A109
C: #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=2mA
I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=10 Driver=qcserial
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c2115b2b16421d93d4993f3fe4c520e91d6fe801 upstream.
Commit 7c75bde329d7 ("usb: musb: musb_dsps: request_irq() after
initializing musb") has inverted the calls to
dsps_setup_optional_vbus_irq() and dsps_create_musb_pdev() without
updating correctly the error path. dsps_create_musb_pdev() allocates and
registers a new platform device which must be unregistered and freed
with platform_device_unregister(), and this is missing upon
dsps_setup_optional_vbus_irq() error.
While on the master branch it seems not to trigger any issue, I observed
a kernel crash because of a NULL pointer dereference with a v5.10.70
stable kernel where the patch mentioned above was backported. With this
kernel version, -EPROBE_DEFER is returned the first time
dsps_setup_optional_vbus_irq() is called which triggers the probe to
error out without unregistering the platform device. Unfortunately, on
the Beagle Bone Black Wireless, the platform device still living in the
system is being used by the USB Ethernet gadget driver, which during the
boot phase triggers the crash.
My limited knowledge of the musb world prevents me to revert this commit
which was sent to silence a robot warning which, as far as I understand,
does not make sense. The goal of this patch was to prevent an IRQ to
fire before the platform device being registered. I think this cannot
ever happen due to the fact that enabling the interrupts is done by the
->enable() callback of the platform musb device, and this platform
device must be already registered in order for the core or any other
user to use this callback.
Hence, I decided to fix the error path, which might prevent future
errors on mainline kernels while also fixing older ones.
Fixes: 7c75bde329d7 ("usb: musb: musb_dsps: request_irq() after initializing musb")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211005221631.1529448-1-miquel.raynal@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea0f69d8211963c4b2cc1998b86779a500adb502 upstream.
Tested on SD5200T TB3 dock which has Fresco Logic FL1100 USB 3.0 Host
Controller.
Before this patch streaming video from USB cam made mouse and keyboard
connected to the same USB bus unusable. Also video was jerky.
With this patch streaming video doesn't have any effect on other
periferals and video is smooth.
Cc: stable@vger.kernel.org
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff0e50d3564f33b7f4b35cadeabd951d66cfc570 upstream.
The command ring pointer is located at [6:63] bits of the command
ring control register (CRCR). All the control bits like command stop,
abort are located at [0:3] bits. While aborting a command, we read the
CRCR and set the abort bit and write to the CRCR. The read will always
give command ring pointer as all zeros. So we essentially write only
the control bits. Since we split the 64 bit write into two 32 bit writes,
there is a possibility of xHC command ring stopped before the upper
dword (all zeros) is written. If that happens, xHC updates the upper
dword of its internal command ring pointer with all zeros. Next time,
when the command ring is restarted, we see xHC memory access failures.
Fix this issue by only writing to the lower dword of CRCR where all
control bits are located.
Cc: stable@vger.kernel.org
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a01ba2a3378be85538e0183ae5367c1bc1d5aaf3 upstream.
See https://github.com/raspberrypi/linux/issues/3981
Two read-modify-write cycles on ep->ep_state are not guarded by
xhci->lock. Fix these.
Fixes: f5249461b504 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 880de403777376e50bdf60def359fa50a722006f upstream.
Make sure to allocate resources before registering the tty device to
avoid having a racing open() and write() fail to enable rx or
dereference a NULL pointer when accessing the uninitialised fifo.
Fixes: dfba2174dc42 ("usb: xhci: Add DbC support in xHCI driver")
Cc: stable@vger.kernel.org # 4.16
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211008092547.3996295-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d91017a295e9790eec02c4e43f020cdb55f5d98 upstream.
TCPM for DRP should do the same action as SRC_ATTACHED when cc changes in
SRC_STARTUP state. Otherwise, TCPM will transition to SRC_UNATTACHED state
which is not satisfied with the Type-C spec.
Per Type-C spec:
DRP port should move to Unattached.SNK instead of Unattached.SRC if sink
removed.
Fixes: 4b4e02c83167 ("typec: tcpm: Move out of staging")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20210928111639.3854174-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58fc1daa4d2e9789b9ffc880907c961ea7c062cc upstream.
A recent change that started reporting break events forgot to push the
event to the line discipline, which meant that a detected break would
not be reported until further characters had been receive (the port
could even have been closed and reopened in between).
Fixes: 08dff274edda ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65a205e6113506e69a503b61d97efec43fc10fd7 upstream.
A recent change that started reporting break events to the line
discipline caused the tty-buffer insertions to no longer be serialised
by inserting events also from the completion handler for the interrupt
endpoint.
Completion calls for distinct endpoints are not guaranteed to be
serialised. For example, in case a host-controller driver uses
bottom-half completion, the interrupt and bulk-in completion handlers
can end up running in parallel on two CPUs (high-and low-prio tasklets,
respectively) thereby breaking the tty layer's single producer
assumption.
Fix this by holding the read lock also when inserting characters from
the bulk endpoint.
Fixes: 08dff274edda ("cdc-acm: fix BREAK rx code path adding necessary calls")
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210929090937.7410-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8253a34bfae3278baca52fc1209b7c29270486ca upstream.
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d1aa9112c8e6995ef2c8a76972c9671332ccfea upstream.
This reverts commit cb9c1cfc86926d0e86d19c8e34f6c23458cd3478 for
USB_LED_TRIG. This config symbol has bool type and enables extra code
in usb_common itself, not a separate driver. Enabling it should not
force usb_common to be built-in!
Fixes: cb9c1cfc8692 ("usb: Kconfig: using select for USB_COMMON dependency")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Salvatore Bonaccorso <carnil@debian.org>
Link: https://lore.kernel.org/r/20210921143442.340087-1-carnil@debian.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 856e6e8e0f9300befa87dde09edb578555c99a82 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210831084236.1359677-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b69ec50b3e55c4b2a85c8bc46763eaf330605847 ]
For DEV_VER_V3 version there exist race condition between clearing
ep_sts.EP_STS_TRBERR and setting ep_cmd.EP_CMD_DRDY bit.
Setting EP_CMD_DRDY will be ignored by controller when
EP_STS_TRBERR is set. So, between these two instructions we have
a small time gap in which the EP_STSS_TRBERR can be set. In such case
the transfer will not start after setting doorbell.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org> # 5.12.x
Tested-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210907062619.34622-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c32dfec6c1c36bbbcd5d33e949d99aeb215877ec upstream.
Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.
This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.
The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]
Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).
[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376
Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835a4 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7a0a792f864583207c593b50fd1b752ed89f4c1 upstream.
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd(). This will make sure both
primary roothub and secondary roothub will be registered along with the
second HCD. This is required for cold plugged USB devices to be detected
in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM
or J7200 EVM).
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e3eed534f8235a4a596a9dae5b8a6425d81ea1a upstream.
Adding support for Foxconn device T99W265 for enumeration with
PID 0xe0db.
usb-devices output for 0xe0db
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 19 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
P: Vendor=0489 ProdID=e0db Rev=05.04
S: Manufacturer=Microsoft
S: Product=Generic Mobile Broadband Adapter
S: SerialNumber=6c50f452
C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I: If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
if0/1: MBIM, if2:Diag, if3:GNSS, if4: Modem
Signed-off-by: Slark Xiao <slark_xiao@163.com>
Link: https://lore.kernel.org/r/20210917110106.9852-1-slark_xiao@163.com
[ johan: use USB_DEVICE_INTERFACE_CLASS(), amend comment ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ca200a8c6f079950a04ea3c3380fe8cf78e95a2 upstream.
The device ZTE 0x0094 is already on the list.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Fixes: b9e44fe5ecda ("USB: option: cleanup zte 3g-dongle's pid in option.c")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7bb057134d609b9c038a00b6876cf0d37d0118ce upstream.
This patch adds the following Telit LN920 compositions:
0x1060: tty, adb, rmnet, tty, tty, tty, tty
0x1061: tty, adb, mbim, tty, tty, tty, tty
0x1062: rndis, tty, adb, tty, tty, tty, tty
0x1063: tty, adb, ecm, tty, tty, tty, tty
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com>
Link: https://lore.kernel.org/r/20210903123913.1086513-1-c.lobrano@gmail.com
Reviewed-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 211f323768a25b30c106fd38f15a0f62c7c2b5f4 upstream.
0xac24 device ID is already defined and used via
BANDB_DEVICE_ID_USO9ML2_4. Remove the duplicate from the list.
Fixes: 27f1281d5f72 ("USB: serial: Extra device/vendor ID for mos7840 driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58877b0824da15698bd85a0a9dbfa8c354e6ecb7 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8cfac9a6744fcb143cb3e94ce002f09fd17fadbb upstream.
After we start to do core soft reset while usb role switch,
the phy init is invoked at every switch to device mode, but
its counter part de-init is missing, this causes the actual
phy init can not be done when we really want to re-init phy
like system resume, because the counter maintained by phy
core is not 0. considering phy init is actually redundant for
role switch, so move out the phy init from core soft reset to
dwc3 core init where is the only place required.
Fixes: f88359e1588b ("usb: dwc3: core: Do core softreset when switch mode")
Cc: <stable@vger.kernel.org>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Tested-by: John Stultz <john.stultz@linaro.org> #HiKey960
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1631068099-13559-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ce1c42b4dacfe7d71c852d8bf3371067ccba865c ups |
