| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 94b619a07655805a1622484967754f5848640456 upstream.
The patch is meant to support LARA-R6 Cat 1 module family.
Module USB ID:
Vendor ID: 0x05c6
Product ID: 0x90fA
Interface layout:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: QMI wwan (not available in all versions)
Signed-off-by: Marco De Marco <marco.demarco@posteo.net>
Link: https://lore.kernel.org/r/49260184.kfMIbaSn9k@mars
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5719df243e118fb343725e8b2afb1637e1af1373 upstream.
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af32605289e ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -22
To fix the issue, disable the tx or rx interrupt in usb_pkt_pop().
Fixes: 2743e7f90dc0 ("usb: renesas_usbhs: fix the usb_pkt_pop()")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210624122039.596528-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5fdf5c6e6bee35837e160c00ac89327bdad031b upstream.
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6abf2fe6b4bf6e5256b80c5817908151d2d33e9f upstream.
LaCie Rugged USB3-FW appears to be incompatible with UAS. It generates
errors like:
[ 1151.582598] sd 14:0:0:0: tag#16 uas_eh_abort_handler 0 uas-tag 1 inflight: IN
[ 1151.582602] sd 14:0:0:0: tag#16 CDB: Report supported operation codes a3 0c 01 12 00 00 00 00 02 00 00 00
[ 1151.588594] scsi host14: uas_eh_device_reset_handler start
[ 1151.710482] usb 2-4: reset SuperSpeed Gen 1 USB device number 2 using xhci_hcd
[ 1151.741398] scsi host14: uas_eh_device_reset_handler success
[ 1181.785534] scsi host14: uas_eh_device_reset_handler start
Signed-off-by: Julian Sikorski <belegdol+github@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210720171910.36497-1-belegdol+github@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bf2761c837571a66ec290fb66c90413821ffda2 upstream.
Maximum Exit Latency (MEL) value is used by host to know how much in
advance it needs to start waking up a U1/U2 suspended link in order to
service a periodic transfer in time.
Current MEL calculation only includes the time to wake up the path from
U1/U2 to U0. This is called tMEL1 in USB 3.1 section C 1.5.2
Total MEL = tMEL1 + tMEL2 +tMEL3 + tMEL4 which should additinally include:
- tMEL2 which is the time it takes for PING message to reach device
- tMEL3 time for device to process the PING and submit a PING_RESPONSE
- tMEL4 time for PING_RESPONSE to traverse back upstream to host.
Add the missing tMEL2, tMEL3 and tMEL4 to MEL calculation.
Cc: <stable@kernel.org> # v3.5
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150122.1995966-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b7f56fbc7a1b66967b6114d1b5f5a257c3abae6 upstream.
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210715150122.1995966-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72f68bf5c756f5ce1139b31daae2684501383ad5 upstream.
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210715150651.1996099-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0665e387318607d8269bfdea60723c627c8bae43 upstream.
Commit a66d21d7dba8 ("usb: xhci: Add support for Renesas controller with
memory") added renesas_usb_fw.mem firmware reference to xhci-pci. Thus
modinfo indicates xhci-pci.ko has "firmware: renesas_usb_fw.mem". But
the firmware is only actually used with CONFIG_USB_XHCI_PCI_RENESAS. An
unusable firmware reference can trigger safety checkers which look for
drivers with unmet firmware dependencies.
Avoid referring to renesas_usb_fw.mem in circumstances when it cannot be
loaded (when CONFIG_USB_XHCI_PCI_RENESAS isn't set).
Fixes: a66d21d7dba8 ("usb: xhci: Add support for Renesas controller with memory")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Thelen <gthelen@google.com>
Link: https://lore.kernel.org/r/20210702071224.3673568-1-gthelen@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44cf53602f5a0db80d53c8fff6cdbcae59650a42 upstream.
This reverts commit d143825baf15f204dac60acdf95e428182aa3374.
Justin reports some of his systems now fail as result of this commit:
xhci_hcd 0000:04:00.0: Direct firmware load for renesas_usb_fw.mem failed with error -2
xhci_hcd 0000:04:00.0: request_firmware failed: -2
xhci_hcd: probe of 0000:04:00.0 failed with error -2
The revert brings back the original issue the commit tried to solve but
at least unbreaks existing systems relying on previous behavior.
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Justin Forbes <jmforbes@linuxtx.org>
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Fixes: d143825baf15 ("usb: renesas-xhci: Fix handling of unknown ROM state")
Link: https://lore.kernel.org/r/20210719070519.41114-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f3a1a937f7b240be623d989c8553a6d01465d04f ]
This reverts commit 0bd860493f81eb2a46173f6f5e44cc38331c8dbd.
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210721092516.2775971-1-vpalatin@chromium.org
Fixes: 0bd860493f81 ("USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d6eef886903c4bb5af41b9a31d4ba11dc7a6f8e8 upstream.
ZLP gets stuck if TDL_CHK bit is set and TDL_FROM_TRB is used
as TDL source for IN endpoints. To fix it, TDL_CHK is only
enabled for OUT endpoints.
Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Link: https://lore.kernel.org/r/1621263912-13175-1-git-send-email-sparmar@cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 88693f770bb09c196b1eb5f06a484a254ecb9924 ]
Fix to return a negative error code from the error handling
case instead of 0.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210618043835.2641360-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33cb46c4676d01956811b68a29157ea969a5df70 ]
Running sparse checker it shows warning message about
incorrect endianness used for descriptor initialization:
| f_hid.c:91:43: warning: incorrect type in initializer (different base types)
| f_hid.c:91:43: expected restricted __le16 [usertype] bcdHID
| f_hid.c:91:43: got int
Fixing issue with cpu_to_le16() macro, however this is not a real issue
as the value is the same both endians.
Cc: Fabien Chouteau <fabien.chouteau@barco.com>
Cc: Segiy Stetsyuk <serg_stetsuk@ukr.net>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Link: https://lore.kernel.org/r/20210617162755.29676-1-ruslan.bilovol@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 880287910b1892ed2cb38977893b947382a09d21 ]
When power on system with OTG cable, IDDIG's interrupt arises before
the charger registration, it will cause a NULL pointer dereference,
fix the issue by registering the power supply before requesting
IDDIG/VBUS irq.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1621406386-18838-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aafe93516b8567ab5864e1f4cd3eeabc54fb0e5a ]
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
Fixes: 1e868545f2bb ("usb: dwc2: gadget: Move gadget phy init into core phy init")
Signed-off-by: Clément Lassieur <clement@lassieur.org>
Link: https://lore.kernel.org/r/20210603155921.940651-1-clement@lassieur.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ecfbd7b9054bddb12cea07fda41bb3a79a7b0149 ]
FunctionFS device structure 'struct ffs_dev' and driver data structure
'struct ffs_data' are bound to each other with cross-reference pointers
'ffs_data->private_data' and 'ffs_dev->ffs_data'. While the first one
is supposed to be valid through the whole life of 'struct ffs_data'
(and while 'struct ffs_dev' exists non-freed), the second one is cleared
in 'ffs_closed()' (called from 'ffs_data_reset()' or the last
'ffs_data_put()'). This can be called several times, alternating in
different order with 'ffs_free_inst()', that, if possible, clears
the other cross-reference.
As a result, different cases of these calls order may leave stale
cross-reference pointers, used when the pointed structure is already
freed. Even if it occasionally doesn't cause kernel crash, this error
is reported by KASAN-enabled kernel configuration.
For example, the case [last 'ffs_data_put()' - 'ffs_free_inst()'] was
fixed by commit cdafb6d8b8da ("usb: gadget: f_fs: Fix use-after-free in
ffs_free_inst").
The other case ['ffs_data_reset()' - 'ffs_free_inst()' - 'ffs_data_put()']
now causes KASAN reported error [1], when 'ffs_data_reset()' clears
'ffs_dev->ffs_data', then 'ffs_free_inst()' frees the 'struct ffs_dev',
but can't clear 'ffs_data->private_data', which is then accessed
in 'ffs_closed()' called from 'ffs_data_put()'. This happens since
'ffs_dev->ffs_data' reference is cleared too early.
Moreover, one more use case, when 'ffs_free_inst()' is called immediately
after mounting FunctionFS device (that is before the descriptors are
written and 'ffs_ready()' is called), and then 'ffs_data_reset()'
or 'ffs_data_put()' is called from accessing "ep0" file or unmounting
the device. This causes KASAN error report like [2], since
'ffs_dev->ffs_data' is not yet set when 'ffs_free_inst()' can't properly
clear 'ffs_data->private_data', that is later accessed to freed structure.
Fix these (and may be other) cases of stale pointers access by moving
setting and clearing of the mentioned cross-references to the single
places, setting both of them when 'struct ffs_data' is created and
bound to 'struct ffs_dev', and clearing both of them when one of the
structures is destroyed. It seems convenient to make this pointer
initialization and structures binding in 'ffs_acquire_dev()' and
make pointers clearing in 'ffs_release_dev()'. This required some
changes in these functions parameters and return types.
Also, 'ffs_release_dev()' calling requires some cleanup, fixing minor
issues, like (1) 'ffs_release_dev()' is not called if 'ffs_free_inst()'
is called without unmounting the device, and "release_dev" callback
is not called at all, or (2) "release_dev" callback is called before
"ffs_closed" callback on unmounting, which seems to be not correctly
nested with "acquire_dev" and "ffs_ready" callbacks.
Make this cleanup togther with other mentioned 'ffs_release_dev()' changes.
[1]
==================================================================
root@rcar-gen3:~# mkdir /dev/cfs
root@rcar-gen3:~# mkdir /dev/ffs
root@rcar-gen3:~# modprobe libcomposite
root@rcar-gen3:~# mount -t configfs none /dev/cfs
root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1
root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs
[ 64.340664] file system registered
root@rcar-gen3:~# mount -t functionfs ffs /dev/ffs
root@rcar-gen3:~# cd /dev/ffs
root@rcar-gen3:/dev/ffs# /home/root/ffs-test
ffs-test: info: ep0: writing descriptors (in v2 format)
[ 83.181442] read descriptors
[ 83.186085] read strings
ffs-test: info: ep0: writing strings
ffs-test: dbg: ep1: starting
ffs-test: dbg: ep2: starting
ffs-test: info: ep1: starts
ffs-test: info: ep2: starts
ffs-test: info: ep0: starts
^C
root@rcar-gen3:/dev/ffs# cd /home/root/
root@rcar-gen3:~# rmdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs
[ 98.935061] unloading
root@rcar-gen3:~# umount /dev/ffs
[ 102.734301] ==================================================================
[ 102.742059] BUG: KASAN: use-after-free in ffs_release_dev+0x64/0xa8 [usb_f_fs]
[ 102.749683] Write of size 1 at addr ffff0004d46ff549 by task umount/2997
[ 102.756709]
[ 102.758311] CPU: 0 PID: 2997 Comm: umount Not tainted 5.13.0-rc4+ #8
[ 102.764971] Hardware name: Renesas Salvator-X board based on r8a77951 (DT)
[ 102.772179] Call trace:
[ 102.774779] dump_backtrace+0x0/0x330
[ 102.778653] show_stack+0x20/0x2c
[ 102.782152] dump_stack+0x11c/0x1ac
[ 102.785833] print_address_description.constprop.0+0x30/0x274
[ 102.791862] kasan_report+0x14c/0x1c8
[ 102.795719] __asan_report_store1_noabort+0x34/0x58
[ 102.800840] ffs_release_dev+0x64/0xa8 [usb_f_fs]
[ 102.805801] ffs_fs_kill_sb+0x50/0x84 [usb_f_fs]
[ 102.810663] deactivate_locked_super+0xa0/0xf0
[ 102.815339] deactivate_super+0x98/0xac
[ 102.819378] cleanup_mnt+0xd0/0x1b0
[ 102.823057] __cleanup_mnt+0x1c/0x28
[ 102.826823] task_work_run+0x104/0x180
[ 102.830774] do_notify_resume+0x458/0x14e0
[ 102.835083] work_pending+0xc/0x5f8
[ 102.838762]
[ 102.840357] Allocated by task 2988:
[ 102.844032] kasan_save_stack+0x28/0x58
[ 102.848071] kasan_set_track+0x28/0x3c
[ 102.852016] ____kasan_kmalloc+0x84/0x9c
[ 102.856142] __kasan_kmalloc+0x10/0x1c
[ 102.860088] __kmalloc+0x214/0x2f8
[ 102.863678] kzalloc.constprop.0+0x14/0x20 [usb_f_fs]
[ 102.868990] ffs_alloc_inst+0x8c/0x208 [usb_f_fs]
[ 102.873942] try_get_usb_function_instance+0xf0/0x164 [libcomposite]
[ 102.880629] usb_get_function_instance+0x64/0x68 [libcomposite]
[ 102.886858] function_make+0x128/0x1ec [libcomposite]
[ 102.892185] configfs_mkdir+0x330/0x590 [configfs]
[ 102.897245] vfs_mkdir+0x12c/0x1bc
[ 102.900835] do_mkdirat+0x180/0x1d0
[ 102.904513] __arm64_sys_mkdirat+0x80/0x94
[ 102.908822] invoke_syscall+0xf8/0x25c
[ 102.912772] el0_svc_common.constprop.0+0x150/0x1a0
[ 102.917891] do_el0_svc+0xa0/0xd4
[ 102.921386] el0_svc+0x24/0x34
[ 102.924613] el0_sync_handler+0xcc/0x154
[ 102.928743] el0_sync+0x198/0x1c0
[ 102.932238]
[ 102.933832] Freed by task 2996:
[ 102.937144] kasan_save_stack+0x28/0x58
[ 102.941181] kasan_set_track+0x28/0x3c
[ 102.945128] kasan_set_free_info+0x28/0x4c
[ 102.949435] ____kasan_slab_free+0x104/0x118
[ 102.953921] __kasan_slab_free+0x18/0x24
[ 102.958047] slab_free_freelist_hook+0x148/0x1f0
[ 102.962897] kfree+0x318/0x440
[ 102.966123] ffs_free_inst+0x164/0x2d8 [usb_f_fs]
[ 102.971075] usb_put_function_instance+0x84/0xa4 [libcomposite]
[ 102.977302] ffs_attr_release+0x18/0x24 [usb_f_fs]
[ 102.982344] config_item_put+0x140/0x1a4 [configfs]
[ 102.987486] configfs_rmdir+0x3fc/0x518 [configfs]
[ 102.992535] vfs_rmdir+0x114/0x234
[ 102.996122] do_rmdir+0x274/0x2b0
[ 102.999617] __arm64_sys_unlinkat+0x94/0xc8
[ 103.004015] invoke_syscall+0xf8/0x25c
[ 103.007961] el0_svc_common.constprop.0+0x150/0x1a0
[ 103.013080] do_el0_svc+0xa0/0xd4
[ 103.016575] el0_svc+0x24/0x34
[ 103.019801] el0_sync_handler+0xcc/0x154
[ 103.023930] el0_sync+0x198/0x1c0
[ 103.027426]
[ 103.029020] The buggy address belongs to the object at ffff0004d46ff500
[ 103.029020] which belongs to the cache kmalloc-128 of size 128
[ 103.042079] The buggy address is located 73 bytes inside of
[ 103.042079] 128-byte region [ffff0004d46ff500, ffff0004d46ff580)
[ 103.054236] The buggy address belongs to the page:
[ 103.059262] page:0000000021aa849b refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff0004d46fee00 pfn:0x5146fe
[ 103.070437] head:0000000021aa849b order:1 compound_mapcount:0
[ 103.076456] flags: 0x8000000000010200(slab|head|zone=2)
[ 103.081948] raw: 8000000000010200 fffffc0013521a80 0000000d0000000d ffff0004c0002300
[ 103.090052] raw: ffff0004d46fee00 000000008020001e 00000001ffffffff 0000000000000000
[ 103.098150] page dumped because: kasan: bad access detected
[ 103.103985]
[ 103.105578] Memory state around the buggy address:
[ 103.110602] ffff0004d46ff400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 103.118161] ffff0004d46ff480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 103.125726] >ffff0004d46ff500: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 103.133284] ^
[ 103.139120] ffff0004d46ff580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 103.146679] ffff0004d46ff600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 103.154238] ==================================================================
[ 103.161792] Disabling lock debugging due to kernel taint
[ 103.167319] Unable to handle kernel paging request at virtual address 0037801d6000018e
[ 103.175406] Mem abort info:
[ 103.178457] ESR = 0x96000004
[ 103.181609] EC = 0x25: DABT (current EL), IL = 32 bits
[ 103.187020] SET = 0, FnV = 0
[ 103.190185] EA = 0, S1PTW = 0
[ 103.193417] Data abort info:
[ 103.196385] ISV = 0, ISS = 0x00000004
[ 103.200315] CM = 0, WnR = 0
[ 103.203366] [0037801d6000018e] address between user and kernel address ranges
[ 103.210611] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 103.216231] Modules linked in: usb_f_fs libcomposite configfs ath9k_htc led_class mac80211 libarc4 ath9k_common ath9k_hw ath cfg80211 aes_ce_blk sata_rc4
[ 103.259233] CPU: 0 PID: 2997 Comm: umount Tainted: G B 5.13.0-rc4+ #8
[ 103.267031] Hardware name: Renesas Salvator-X board based on r8a77951 (DT)
[ 103.273951] pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 103.280001] pc : ffs_data_clear+0x138/0x370 [usb_f_fs]
[ 103.285197] lr : ffs_data_clear+0x124/0x370 [usb_f_fs]
[ 103.290385] sp : ffff800014777a80
[ 103.293725] x29: ffff800014777a80 x28: ffff0004d7649c80 x27: 0000000000000000
[ 103.300931] x26: ffff800014777fb0 x25: ffff60009aec9394 x24: ffff0004d7649ca4
[ 103.308136] x23: 1fffe0009a3d063a x22: dfff800000000000 x21: ffff0004d1e831d0
[ 103.315340] x20: e1c000eb00000bb4 x19: ffff0004d1e83000 x18: 0000000000000000
[ 103.322545] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 103.329748] x14: 0720072007200720 x13: 0720072007200720 x12: 1ffff000012ef658
[ 103.336952] x11: ffff7000012ef658 x10: 0720072007200720 x9 : ffff800011322648
[ 103.344157] x8 : ffff800014777818 x7 : ffff80000977b2c7 x6 : 0000000000000000
[ 103.351359] x5 : 0000000000000001 x4 : ffff7000012ef659 x3 : 0000000000000001
[ 103.358562] x2 : 0000000000000000 x1 : 1c38001d6000018e x0 : e1c000eb00000c70
[ 103.365766] Call trace:
[ 103.368235] ffs_data_clear+0x138/0x370 [usb_f_fs]
[ 103.373076] ffs_data_reset+0x20/0x304 [usb_f_fs]
[ 103.377829] ffs_data_closed+0x1ec/0x244 [usb_f_fs]
[ 103.382755] ffs_fs_kill_sb+0x70/0x84 [usb_f_fs]
[ 103.387420] deactivate_locked_super+0xa0/0xf0
[ 103.391905] deactivate_super+0x98/0xac
[ 103.395776] cleanup_mnt+0xd0/0x1b0
[ 103.399299] __cleanup_mnt+0x1c/0x28
[ 103.402906] task_work_run+0x104/0x180
[ 103.406691] do_notify_resume+0x458/0x14e0
[ 103.410823] work_pending+0xc/0x5f8
[ 103.414351] Code: b4000a54 9102f280 12000802 d343fc01 (38f66821)
[ 103.420490] ---[ end trace 57b43a50e8244f57 ]---
Segmentation fault
root@rcar-gen3:~#
==================================================================
[2]
==================================================================
root@rcar-gen3:~# mkdir /dev/ffs
root@rcar-gen3:~# modprobe libcomposite
root@rcar-gen3:~#
root@rcar-gen3:~# mount -t configfs none /dev/cfs
root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1
root@rcar-gen3:~# mkdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs
[ 54.766480] file system registered
root@rcar-gen3:~# mount -t functionfs ffs /dev/ffs
root@rcar-gen3:~# rmdir /dev/cfs/usb_gadget/g1/functions/ffs.ffs
[ 63.197597] unloading
root@rcar-gen3:~# cat /dev/ffs/ep0
cat: read error:[ 67.213506] ==================================================================
[ 67.222095] BUG: KASAN: use-after-free in ffs_data_clear+0x70/0x370 [usb_f_fs]
[ 67.229699] Write of size 1 at addr ffff0004c26e974a by task cat/2994
[ 67.236446]
[ 67.238045] CPU: 0 PID: 2994 Comm: cat Not tainted 5.13.0-rc4+ #8
[ 67.244431] Hardware name: Renesas Salvator-X board based on r8a77951 (DT)
[ 67.251624] Call trace:
[ 67.254212] dump_backtrace+0x0/0x330
[ 67.258081] show_stack+0x20/0x2c
[ 67.261579] dump_stack+0x11c/0x1ac
[ 67.265260] print_address_description.constprop.0+0x30/0x274
[ 67.271286] kasan_report+0x14c/0x1c8
[ 67.275143] __asan_report_store1_noabort+0x34/0x58
[ 67.280265] ffs_data_clear+0x70/0x370 [usb_f_fs]
[ 67.285220] ffs_data_reset+0x20/0x304 [usb_f_fs]
[ 67.290172] ffs_data_closed+0x240/0x244 [usb_f_fs]
[ 67.295305] ffs_ep0_release+0x40/0x54 [usb_f_fs]
[ 67.300256] __fput+0x304/0x580
[ 67.303576] ____fput+0x18/0x24
[ 67.306893] task_work_run+0x104/0x180
[ 67.310846] do_notify_resume+0x458/0x14e0
[ 67.315154] work_pending+0xc/0x5f8
[ 67.318834]
[ 67.320429] Allocated by task 2988:
[ 67.324105] kasan_save_stack+0x28/0x58
[ 67.328144] kasan_set_track+0x28/0x3c
[ 67.332090] ____kasan_kmalloc+0x84/0x9c
[ 67.336217] __kasan_kmalloc+0x10/0x1c
[ 67.340163] __kmalloc+0x214/0x2f8
[ 67.343754] kzalloc.constprop.0+0x14/0x20 [usb_f_fs]
[ 67.349066] ffs_alloc_inst+0x8c/0x208 [usb_f_fs]
[ 67.354017] try_get_usb_function_instance+0xf0/0x164 [libcomposite]
[ 67.360705] usb_get_function_instance+0x64/0x68 [libcomposite]
[ 67.366934] function_make+0x128/0x1ec [libcomposite]
[ 67.372260] configfs_mkdir+0x330/0x590 [configfs]
[ 67.377320] vfs_mkdir+0x12c/0x1bc
[ 67.380911] do_mkdirat+0x180/0x1d0
[ 67.384589] __arm64_sys_mkdirat+0x80/0x94
[ 67.388899] invoke_syscall+0xf8/0x25c
[ 67.392850] el0_svc_common.constprop.0+0x150/0x1a0
[ 67.397969] do_el0_svc+0xa0/0xd4
[ 67.401464] el0_svc+0x24/0x34
[ 67.404691] el0_sync_handler+0xcc/0x154
[ 67.408819] el0_sync+0x198/0x1c0
[ 67.412315]
[ 67.413909] Freed by task 2993:
[ 67.417220] kasan_save_stack+0x28/0x58
[ 67.421257] kasan_set_track+0x28/0x3c
[ 67.425204] kasan_set_free_info+0x28/0x4c
[ 67.429513] ____kasan_slab_free+0x104/0x118
[ 67.434001] __kasan_slab_free+0x18/0x24
[ 67.438128] slab_free_freelist_hook+0x148/0x1f0
[ 67.442978] kfree+0x318/0x440
[ 67.446205] ffs_free_inst+0x164/0x2d8 [usb_f_fs]
[ 67.451156] usb_put_function_instance+0x84/0xa4 [libcomposite]
[ 67.457385] ffs_attr_release+0x18/0x24 [usb_f_fs]
[ 67.462428] config_item_put+0x140/0x1a4 [configfs]
[ 67.467570] configfs_rmdir+0x3fc/0x518 [configfs]
[ 67.472626] vfs_rmdir+0x114/0x234
[ 67.476215] do_rmdir+0x274/0x2b0
[ 67.479710] __arm64_sys_unlinkat+0x94/0xc8
[ 67.484108] invoke_syscall+0xf8/0x25c
[ 67.488055] el0_svc_common.constprop.0+0x150/0x1a0
[ 67.493175] do_el0_svc+0xa0/0xd4
[ 67.496671] el0_svc+0x24/0x34
[ 67.499896] el0_sync_handler+0xcc/0x154
[ 67.504024] el0_sync+0x198/0x1c0
[ 67.507520]
[ 67.509114] The buggy address belongs to the object at ffff0004c26e9700
[ 67.509114] which belongs to the cache kmalloc-128 of size 128
[ 67.522171] The buggy address is located 74 bytes inside of
[ 67.522171] 128-byte region [ffff0004c26e9700, ffff0004c26e9780)
[ 67.534328] The buggy address belongs to the page:
[ 67.539355] page:000000003177a217 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x5026e8
[ 67.549175] head:000000003177a217 order:1 compound_mapcount:0
[ 67.555195] flags: 0x8000000000010200(slab|head|zone=2)
[ 67.560687] raw: 8000000000010200 fffffc0013037100 0000000c00000002 ffff0004c0002300
[ 67.568791] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000
[ 67.576890] page dumped because: kasan: bad access detected
[ 67.582725]
[ 67.584318] Memory state around the buggy address:
[ 67.589343] ffff0004c26e9600: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 67.596903] ffff0004c26e9680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 67.604463] >ffff0004c26e9700: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 67.612022] ^
[ 67.617860] ffff0004c26e9780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 67.625421] ffff0004c26e9800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 67.632981] ==================================================================
[ 67.640535] Disabling lock debugging due to kernel taint
File descriptor[ 67.646100] Unable to handle kernel paging request at virtual address fabb801d4000018d
in bad state
[ 67.655456] Mem abort info:
[ 67.659619] ESR = 0x96000004
[ 67.662801] EC = 0x25: DABT (current EL), IL = 32 bits
[ 67.668225] SET = 0, FnV = 0
[ 67.671375] EA = 0, S1PTW = 0
[ 67.674613] Data abort info:
[ 67.677587] ISV = 0, ISS = 0x00000004
[ 67.681522] CM = 0, WnR = 0
[ 67.684588] [fabb801d4000018d] address between user and kernel address ranges
[ 67.691849] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 67.697470] Modules linked in: usb_f_fs libcomposite configfs ath9k_htc led_class mac80211 libarc4 ath9k_common ath9k_hw ath cfg80211 aes_ce_blk crypto_simd cryptd aes_ce_cipher ghash_ce gf128mul sha2_ce sha1_ce evdev sata_rcar libata xhci_plat_hcd scsi_mod xhci_hcd rene4
[ 67.740467] CPU: 0 PID: 2994 Comm: cat Tainted: G B 5.13.0-rc4+ #8
[ 67.748005] Hardware name: Renesas Salvator-X board based on r8a77951 (DT)
[ 67.754924] pstate: 00000005 (nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 67.760974] pc : ffs_data_clear+0x138/0x370 [usb_f_fs]
[ 67.766178] lr : ffs_data_clear+0x124/0x370 [usb_f_fs]
[ 67.771365] sp : ffff800014767ad0
[ 67.774706] x29: ffff800014767ad0 x28: ffff800009cf91c0 x27: ffff0004c54861a0
[ 67.781913] x26: ffff0004dc90b288 x25: 1fffe00099ec10f5 x24: 00000000000a801d
[ 67.789118] x23: 1fffe00099f6953a x22: dfff800000000000 x21: ffff0004cfb4a9d0
[ 67.796322] x20: d5e000ea00000bb1 x19: ffff0004cfb4a800 x18: 0000000000000000
[ 67.803526] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 67.810730] x14: 0720072007200720 x13: 0720072007200720 x12: 1ffff000028ecefa
[ 67.817934] x11: ffff7000028ecefa x10: 0720072007200720 x9 : ffff80001132c014
[ 67.825137] x8 : ffff8000147677d8 x7 : ffff8000147677d7 x6 : 0000000000000000
[ 67.832341] x5 : 0000000000000001 x4 : ffff7000028ecefb x3 : 0000000000000001
[ 67.839544] x2 : 0000000000000005 x1 : 1abc001d4000018d x0 : d5e000ea00000c6d
[ 67.846748] Call trace:
[ 67.849218] ffs_data_clear+0x138/0x370 [usb_f_fs]
[ 67.854058] ffs_data_reset+0x20/0x304 [usb_f_fs]
[ 67.858810] ffs_data_closed+0x240/0x244 [usb_f_fs]
[ 67.863736] ffs_ep0_release+0x40/0x54 [usb_f_fs]
[ 67.868488] __fput+0x304/0x580
[ 67.871665] ____fput+0x18/0x24
[ 67.874837] task_work_run+0x104/0x180
[ 67.878622] do_notify_resume+0x458/0x14e0
[ 67.882754] work_pending+0xc/0x5f8
[ 67.886282] Code: b4000a54 9102f280 12000802 d343fc01 (38f66821)
[ 67.892422] ---[ end trace 6d7cedf53d7abbea ]---
Segmentation fault
root@rcar-gen3:~#
==================================================================
Fixes: 4b187fceec3c ("usb: gadget: FunctionFS: add devices management code")
Fixes: 3262ad824307 ("usb: gadget: f_fs: Stop ffs_closed NULL pointer dereference")
Fixes: cdafb6d8b8da ("usb: gadget: f_fs: Fix use-after-free in ffs_free_inst")
Reported-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Link: https://lore.kernel.org/r/20210603171507.22514-1-andrew_gabbasov@mentor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b31d9d6d7abbf6483b871b6370bc31c930d53f54 upstream.
when system is doing s4, the process of xhci_resume may be as below:
1、xhci_mem_cleanup
2、xhci_init->xhci_mem_init->xhci_mem_cleanup(when memory is not enough).
xhci_mem_cleanup will be executed twice when system is out of memory.
xhci->port_caps is freed in xhci_mem_cleanup,but it isn't set to NULL.
It will be freed twice when xhci_mem_cleanup is called the second time.
We got following bug when system resumes from s4:
kernel BUG at mm/slub.c:309!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
CPU: 0 PID: 5929 Tainted: G S W 5.4.96-arm64-desktop #1
pc : __slab_free+0x5c/0x424
lr : kfree+0x30c/0x32c
Call trace:
__slab_free+0x5c/0x424
kfree+0x30c/0x32c
xhci_mem_cleanup+0x394/0x3cc
xhci_mem_init+0x9ac/0x1070
xhci_init+0x8c/0x1d0
xhci_resume+0x1cc/0x5fc
xhci_plat_resume+0x64/0x70
platform_pm_thaw+0x28/0x60
dpm_run_callback+0x54/0x24c
device_resume+0xd0/0x200
async_resume+0x24/0x60
async_run_entry_fn+0x44/0x110
process_one_work+0x1f0/0x490
worker_thread+0x5c/0x450
kthread+0x158/0x160
ret_from_fork+0x10/0x24
Original patch that caused this issue was backported to 4.4 stable,
so this should be backported to 4.4 stabe as well.
Fixes: cf0ee7c60c89 ("xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Tao Xue <xuetao09@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210617150354.1512157-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03026197bb657d784220b040c6173267a0375741 upstream.
typec_register_altmode() misses to call altmode_id_remove() in an error
path. Add the missed function call to fix it.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes")
Cc: stable <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20210617073226.47599-1-jingxiangfeng@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84524d1232ecca7cf8678e851b254f05cff4040a upstream.
Creation EP's debugfs called earlier than debugfs folder for dwc3
device created. As result EP's debugfs are created in '/sys/kernel/debug'
instead of '/sys/kernel/debug/usb/dwc3.1.auto'.
Moved dwc3_debugfs_init() function call before calling
dwc3_core_init_mode() to allow create dwc3 debugfs parent before
creating EP's debugfs's.
Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/01fafb5b2d8335e98e6eadbac61fc796bdf3ec1a.1623948457.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4897807753e078655a78de39ed76044d784f3e63 upstream.
The device (32a7:0000 Heimann Sensor GmbH USB appset demo) claims to be
a CDC-ACM device in its descriptors but in fact is not. If it is run
with echo disabled it returns garbled data, probably due to something
that happens in the TTY layer. And when run with echo enabled (the
default), it will mess up the calibration data of the sensor the first
time any data is sent to the device.
In short, I had a bad time after connecting the sensor and trying to get
it to work. I hope blacklisting it in the cdc-acm driver will save
someone else a bit of trouble.
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210622141454.337948-1-hannu@hrtk.in
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d143825baf15f204dac60acdf95e428182aa3374 upstream.
The ROM load sometimes seems to return an unknown status
(RENESAS_ROM_STATUS_NO_RESULT) instead of success / fail.
If the ROM load indeed failed this leads to failures when trying to
communicate with the controller later on.
Attempt to load firmware using RAM load in those cases.
Fixes: 2478be82de44 ("usb: renesas-xhci: Add ROM loader for uPD720201")
Cc: stable@vger.kernel.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Link: https://lore.kernel.org/r/20210615153758.253572-1-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4249d6fbc10fd997abdf8a1ea49c0389a0edf706 upstream.
when receive eem echo command, it will send a response,
but queue this response to the usb request which allocate
from gadget device endpoint zero,
and transmit the request to IN endpoint of eem interface.
on dwc3 gadget, it will trigger following warning in function
__dwc3_gadget_ep_queue(),
if (WARN(req->dep != dep, "request %pK belongs to '%s'\n",
&req->request, req->dep->name))
return -EINVAL;
fix it by allocating a usb request from IN endpoint of eem interface,
and transmit the usb request to same IN endpoint of eem interface.
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210616115142.34075-1-linyyuan@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bf584a03eec674975ee9fe36c8583d9d470dab1 upstream.
When do system reboot, it calls dwc3_shutdown and the whole debugfs
for dwc3 has removed first, when the gadget tries to do deinit, and
remove debugfs for its endpoints, it meets NULL pointer dereference
issue when call debugfs_lookup. Fix it by removing the whole dwc3
debugfs later than dwc3_drd_exit.
[ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002
....
[ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 2925.037005] pc : inode_permission+0x2c/0x198
[ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8
[ 2925.045903] sp : ffff80001276ba70
[ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000
[ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100
[ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001
[ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000
[ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004
[ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030
[ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420
[ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080
[ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065
[ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188
[ 2925.120671] Call trace:
[ 2925.123119] inode_permission+0x2c/0x198
[ 2925.127042] lookup_one_len_common+0xb0/0xf8
[ 2925.131315] lookup_one_len_unlocked+0x34/0xb0
[ 2925.135764] lookup_positive_unlocked+0x14/0x50
[ 2925.140296] debugfs_lookup+0x68/0xa0
[ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0
[ 2925.148675] dwc3_gadget_exit+0x28/0x78
[ 2925.152518] dwc3_drd_exit+0x100/0x1f8
[ 2925.156267] dwc3_remove+0x11c/0x120
[ 2925.159851] dwc3_shutdown+0x14/0x20
[ 2925.163432] platform_shutdown+0x28/0x38
[ 2925.167360] device_shutdown+0x15c/0x378
[ 2925.171291] kernel_restart_prepare+0x3c/0x48
[ 2925.175650] kernel_restart+0x1c/0x68
[ 2925.179316] __do_sys_reboot+0x218/0x240
[ 2925.183247] __arm64_sys_reboot+0x28/0x30
[ 2925.187262] invoke_syscall+0x48/0x100
[ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8
[ 2925.195726] do_el0_svc+0x28/0x88
[ 2925.199045] el0_svc+0x20/0x30
[ 2925.202104] el0_sync_handler+0xa8/0xb0
[ 2925.205942] el0_sync+0x148/0x180
[ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660)
[ 2925.215372] ---[ end trace 124254d8e485a58b ]---
[ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
[ 2925.227676] Kernel Offset: disabled
[ 2925.231164] CPU features: 0x00001001,20000846
[ 2925.235521] Memory Limit: none
[ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
Fixes: 8d396bb0a5b6 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically")
Cc: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20210608105656.10795-1-peter.chen@kernel.org
(cherry picked from commit 2a042767814bd0edf2619f06fecd374e266ea068)
Link: https://lore.kernel.org/r/20210615080847.GA10432@jackp-linux.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d396bb0a5b62b326f6be7594d8bd46b088296bd upstream.
The DWC3 DebugFS directory and files are currently created once
during probe. This includes creation of subdirectories for each
of the gadget's endpoints. This works fine for peripheral-only
controllers, as dwc3_core_init_mode() calls dwc3_gadget_init()
just prior to calling dwc3_debugfs_init().
However, for dual-role controllers, dwc3_core_init_mode() will
instead call dwc3_drd_init() which is problematic in a few ways.
First, the initial state must be determined, then dwc3_set_mode()
will have to schedule drd_work and by then dwc3_debugfs_init()
could have already been invoked. Even if the initial mode is
peripheral, dwc3_gadget_init() happens after the DebugFS files
are created, and worse so if the initial state is host and the
controller switches to peripheral much later. And secondly,
even if the gadget endpoints' debug entries were successfully
created, if the controller exits peripheral mode, its dwc3_eps
are freed so the debug files would now hold stale references.
So it is best if the DebugFS endpoint entries are created and
removed dynamically at the same time the underlying dwc3_eps are.
Do this by calling dwc3_debugfs_create_endpoint_dir() as each
endpoint is created, and conversely remove the DebugFS entry when
the endpoint is freed.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210529192932.22912-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6d580d96f140596d69220f60ce0cfbea4ee5c0f upstream.
i.MX8MM cannot detect certain CDP USB HUBs. usbmisc_imx.c driver is not
following CDP timing requirements defined by USB BC 1.2 specification
and section 3.2.4 Detection Timing CDP.
During Primary Detection the i.MX device should turn on VDP_SRC and
IDM_SINK for a minimum of 40ms (TVDPSRC_ON). After a time of TVDPSRC_ON,
the i.MX is allowed to check the status of the D- line. Current
implementation is waiting between 1ms and 2ms, and certain BC 1.2
complaint USB HUBs cannot be detected. Increase delay to 40ms allowing
enough time for primary detection.
During secondary detection the i.MX is required to disable VDP_SRC and
IDM_SNK, and enable VDM_SRC and IDP_SINK for at least 40ms (TVDMSRC_ON).
Current implementation is not disabling VDP_SRC and IDM_SNK, introduce
disable sequence in imx7d_charger_secondary_detection() function.
VDM_SRC and IDP_SINK should be enabled for at least 40ms (TVDMSRC_ON).
Increase delay allowing enough time for detection.
Cc: <stable@vger.kernel.org>
Fixes: 746f316b753a ("usb: chipidea: introduce imx7d USB charger detection")
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20210614175013.495808-1-breno.lima@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7d8d1c7a7f73e780aa9ae74926ae5985b2f895f upstream.
The Cypress CY7C65632 appears to have an issue with auto suspend and
detecting devices, not too dissimilar to the SMSC 5534B hub. It is
easiest to reproduce by connecting multiple mass storage devices to
the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts
result in the devices not being detected. It is however possible to
make them appear using lsusb -v.
Disabling autosuspend for this hub resolves the issue.
Fixes: 1208f9e1d758 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 142d0b24c1b17139f1aaaacae7542a38aa85640f upstream.
Fix the copy-paste mistake in the return path of typec_mux_match(),
where dev is considered a member of struct typec_switch rather than
struct typec_mux.
The two structs are identical in regards to having the struct device as
the first entry, so this provides no functional change.
Fixes: 3370db35193b ("usb: typec: Registering real device entries for the muxes")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610002132.3088083-1-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8212937305f84ef73ea81036dafb80c557583d4b upstream.
Current sequence utilizes dwc3_gadget_disable_irq() alongside
synchronize_irq() to ensure that no further DWC3 events are generated.
However, the dwc3_gadget_disable_irq() API only disables device
specific events. Endpoint events can still be generated. Briefly
disable the interrupt line, so that the cleanup code can run to
prevent device and endpoint events. (i.e. __dwc3_gadget_stop() and
dwc3_stop_active_transfers() respectively)
Without doing so, it can lead to both the interrupt handler and the
pullup disable routine both writing to the GEVNTCOUNT register, which
will cause an incorrect count being read from future interrupts.
Fixes: ae7e86108b12 ("usb: dwc3: Stop act |
