| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit c4dedaaeb3f78d3718e9c1b1e4d972a6b99073cd upstream.
When starting the SD Express process, the low power negotiation mode will
be disabled, so we need to re-enable it after switching back to SD mode.
Fixes: 0e92aec2efa0 ("mmc: sdhci-pci-gli: Add support SD Express card for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-2-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8c68b5656e55e9324875881f1000eb4ee3603a87 upstream.
On sdhci_gl9767_set_clock(), the vendor header space(VHS) is read-only
after calling gl9767_disable_ssc_pll() and gl9767_set_ssc_pll_205mhz().
So the low power negotiation mode cannot be enabled again.
Introduce gl9767_set_low_power_negotiation() function to fix it.
The explanation process is as below.
static void sdhci_gl9767_set_clock()
{
...
gl9767_vhs_write();
...
value |= PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <--- (a)
gl9767_disable_ssc_pll(); <--- (b)
sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
if (clock == 0)
return; <-- (I)
...
if (clock == 200000000 && ios->timing == MMC_TIMING_UHS_SDR104) {
...
gl9767_set_ssc_pll_205mhz(); <--- (c)
}
...
value &= ~PCIE_GLI_9767_CFG_LOW_PWR_OFF;
pci_write_config_dword(pdev, PCIE_GLI_9767_CFG, value); <-- (II)
gl9767_vhs_read();
}
(a) disable low power negotiation mode. When return on (I), the low power
mode is disabled. After (b) and (c), VHS is read-only, the low power mode
cannot be enabled on (II).
Reported-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Fixes: d2754355512e ("mmc: sdhci-pci-gli: Set SDR104's clock to 205MHz and enable SSC for GL9767")
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Georg Gottleuber <ggo@tuxedocomputers.com>
Cc: stable@vger.kernel.org
Message-ID: <20241025060017.1663697-1-benchuanggli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6575b268157f37929948a8d1f3bafb3d7c055bc1 upstream.
When the CXL subsystem is built-in the module init order is determined
by Makefile order. That order violates expectations. The expectation is
that cxl_acpi and cxl_mem can race to attach. If cxl_acpi wins the race,
cxl_mem will find the enabled CXL root ports it needs. If cxl_acpi loses
the race it will retrigger cxl_mem to attach via cxl_bus_rescan(). That
flow only works if cxl_acpi can assume ports are enabled immediately
upon cxl_acpi_probe() return. That in turn can only happen in the
CONFIG_CXL_ACPI=y case if the cxl_port driver is registered before
cxl_acpi_probe() runs.
Fix up the order to prevent initialization failures. Ensure that
cxl_port is built-in when cxl_acpi is also built-in, arrange for
Makefile order to resolve the subsys_initcall() order of cxl_port and
cxl_acpi, and arrange for Makefile order to resolve the
device_initcall() (module_init()) order of the remaining objects.
As for what contributed to this not being found earlier, the CXL
regression environment, cxl_test, builds all CXL functionality as a
module to allow to symbol mocking and other dynamic reload tests. As a
result there is no regression coverage for the built-in case.
Reported-by: Gregory Price <gourry@gourry.net>
Closes: http://lore.kernel.org/20241004212504.1246-1-gourry@gourry.net
Tested-by: Gregory Price <gourry@gourry.net>
Fixes: 8dd2bc0f8e02 ("cxl/mem: Add the cxl_mem driver")
Cc: stable@vger.kernel.org
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jonathan Cameron <jonathan.cameron@huawei.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Alejandro Lucero <alucerop@amd.com>
Reviewed-by: Alejandro Lucero <alucerop@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Link: https://patch.msgid.link/172988474904.476062.7961350937442459266.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 101c268bd2f37e965a5468353e62d154db38838e upstream.
In support of investigating an initialization failure report [1],
cxl_test was updated to register mock memory-devices after the mock
root-port/bus device had been registered. That led to cxl_test crashing
with a use-after-free bug with the following signature:
cxl_port_attach_region: cxl region3: cxl_host_bridge.0:port3 decoder3.0 add: mem0:decoder7.0 @ 0 next: cxl_switch_uport.0 nr_eps: 1 nr_targets: 1
cxl_port_attach_region: cxl region3: cxl_host_bridge.0:port3 decoder3.0 add: mem4:decoder14.0 @ 1 next: cxl_switch_uport.0 nr_eps: 2 nr_targets: 1
cxl_port_setup_targets: cxl region3: cxl_switch_uport.0:port6 target[0] = cxl_switch_dport.0 for mem0:decoder7.0 @ 0
1) cxl_port_setup_targets: cxl region3: cxl_switch_uport.0:port6 target[1] = cxl_switch_dport.4 for mem4:decoder14.0 @ 1
[..]
cxld_unregister: cxl decoder14.0:
cxl_region_decode_reset: cxl_region region3:
mock_decoder_reset: cxl_port port3: decoder3.0 reset
2) mock_decoder_reset: cxl_port port3: decoder3.0: out of order reset, expected decoder3.1
cxl_endpoint_decoder_release: cxl decoder14.0:
[..]
cxld_unregister: cxl decoder7.0:
3) cxl_region_decode_reset: cxl_region region3:
Oops: general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6bc3: 0000 [#1] PREEMPT SMP PTI
[..]
RIP: 0010:to_cxl_port+0x8/0x60 [cxl_core]
[..]
Call Trace:
<TASK>
cxl_region_decode_reset+0x69/0x190 [cxl_core]
cxl_region_detach+0xe8/0x210 [cxl_core]
cxl_decoder_kill_region+0x27/0x40 [cxl_core]
cxld_unregister+0x5d/0x60 [cxl_core]
At 1) a region has been established with 2 endpoint decoders (7.0 and
14.0). Those endpoints share a common switch-decoder in the topology
(3.0). At teardown, 2), decoder14.0 is the first to be removed and hits
the "out of order reset case" in the switch decoder. The effect though
is that region3 cleanup is aborted leaving it in-tact and
referencing decoder14.0. At 3) the second attempt to teardown region3
trips over the stale decoder14.0 object which has long since been
deleted.
The fix here is to recognize that the CXL specification places no
mandate on in-order shutdown of switch-decoders, the driver enforces
in-order allocation, and hardware enforces in-order commit. So, rather
than fail and leave objects dangling, always remove them.
In support of making cxl_region_decode_reset() always succeed,
cxl_region_invalidate_memregion() failures are turned into warnings.
Crashing the kernel is ok there since system integrity is at risk if
caches cannot be managed around physical address mutation events like
CXL region destruction.
A new device_for_each_child_reverse_from() is added to cleanup
port->commit_end after all dependent decoders have been disabled. In
other words if decoders are allocated 0->1->2 and disabled 1->2->0 then
port->commit_end only decrements from 2 after 2 has been disabled, and
it decrements all the way to zero since 1 was disabled previously.
Link: http://lore.kernel.org/20241004212504.1246-1-gourry@gourry.net [1]
Cc: stable@vger.kernel.org
Fixes: 176baefb2eb5 ("cxl/hdm: Commit decoder state to hardware")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Alison Schofield <alison.schofield@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/172964782781.81806.17902885593105284330.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8c879192465d9f328cb0df07208ef077c560bb1 upstream.
Some versions of the pmic_glink firmware does not allow dynamic GLINK
intent allocations, attempting to send a message before the firmware has
allocated its receive buffers and announced these intent allocations
will fail. When this happens something like this showns up in the log:
pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: failed to send altmode request: 0x10 (-125)
pmic_glink_altmode.pmic_glink_altmode pmic_glink.altmode.0: failed to request altmode notifications: -125
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: failed to send UCSI read request: -125
qcom_battmgr.pmic_glink_power_supply pmic_glink.power-supply.0: failed to request power notifications
GLINK has been updated to distinguish between the cases where the remote
is going down (-ECANCELED) and the intent allocation being rejected
(-EAGAIN).
Retry the send until intent buffers becomes available, or an actual
error occur.
To avoid infinitely waiting for the firmware in the event that this
misbehaves and no intents arrive, an arbitrary 5 second timeout is
used.
This patch was developed with input from Chris Lew.
Reported-by: Johan Hovold <johan@kernel.org>
Closes: https://lore.kernel.org/all/Zqet8iInnDhnxkT9@hovoldconsulting.com/#t
Cc: stable@vger.kernel.org # rpmsg: glink: Handle rejected intent request better
Fixes: 58ef4ece1e41 ("soc: qcom: pmic_glink: Introduce base PMIC GLINK driver")
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Reviewed-by: Chris Lew <quic_clew@quicinc.com>
Link: https://lore.kernel.org/r/20241023-pmic-glink-ecancelled-v2-2-ebc268129407@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3cea8af2d1a9ae5869b47c3dabe3b20f331f3bbd upstream.
Currently, when configuring TMU (Time Management Unit) mode of a given
router, we take into account only its own TMU requirements ignoring
other routers in the domain. This is problematic if the router we are
configuring has lower TMU requirements than what is already configured
in the domain.
In the scenario below, we have a host router with two USB4 ports: A and
B. Port A connected to device router #1 (which supports CL states) and
existing DisplayPort tunnel, thus, the TMU mode is HiFi uni-directional.
1. Initial topology
[Host]
A/
/
[Device #1]
/
Monitor
2. Plug in device #2 (that supports CL states) to downstream port B of
the host router
[Host]
A/ B\
/ \
[Device #1] [Device #2]
/
Monitor
The TMU mode on port B and port A will be configured to LowRes which is
not what we want and will cause monitor to start flickering.
To address this we first scan the domain and search for any router
configured to HiFi uni-directional mode, and if found, configure TMU
mode of the given router to HiFi uni-directional as well.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9e1b20fae7de06ba36dd3f8dba858157bad233d upstream.
KASAN reported following issue:
BUG: KASAN: stack-out-of-bounds in tb_retimer_scan+0xffe/0x1550 [thunderbolt]
Read of size 4 at addr ffff88810111fc1c by task kworker/u56:0/11
CPU: 0 UID: 0 PID: 11 Comm: kworker/u56:0 Tainted: G U 6.11.0+ #1387
Tainted: [U]=USER
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
<TASK>
dump_stack_lvl+0x6c/0x90
print_report+0xd1/0x630
kasan_report+0xdb/0x110
__asan_report_load4_noabort+0x14/0x20
tb_retimer_scan+0xffe/0x1550 [thunderbolt]
tb_scan_port+0xa6f/0x2060 [thunderbolt]
tb_handle_hotplug+0x17b1/0x3080 [thunderbolt]
process_one_work+0x626/0x1100
worker_thread+0x6c8/0xfa0
kthread+0x2c8/0x3a0
ret_from_fork+0x3a/0x80
ret_from_fork_asm+0x1a/0x30
This happens because the loop variable still gets incremented by one so
max becomes 3 instead of 2, and this makes the second loop read past the
the array declared on the stack.
Fix this by assigning to max directly in the loop body.
Fixes: ff6ab055e070 ("thunderbolt: Add receiver lane margining support for retimers")
CC: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
timeout errors
commit 83beece5aff75879bdfc6df8ba84ea88fd93050e upstream.
fw_upload's poll_complete() is really intended for use with
asynchronous write() implementations - or at least those where the
write() loop may terminate without the kernel yet being aware of whether
or not the firmware upload has succeeded. For auto-update, write() is
only ever called once and will only return when uploading has completed,
be that by passing or failing. The core fw_upload code only calls
poll_complete() after the final call to write() has returned.
However, the poll_complete() implementation in the auto-update driver
was written to expect poll_complete() to be called from another context,
and it waits for a completion signalled from write(). Since
poll_complete() is actually called from the same context, after the
write() loop has terminated, wait_for_completion() never sees the
completion get signalled and always times out, causing programming to
always report a failing.
Since write() is full synchronous, and its return value will indicate
whether or not programming passed or failed, poll_complete() serves no
purpose and can be cut down to simply return FW_UPLOAD_ERR_NONE.
Cc: stable@vger.kernel.org
Fixes: ec5b0f1193ad4 ("firmware: microchip: add PolarFire SoC Auto Update support")
Reported-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Tested-by: Jamie Gibbons <jamie.gibbons@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63dd163cd61dda6f38343776b42331cc6b7e56e0 upstream.
The raw value conversion to obtain a measurement in lux as
INT_PLUS_MICRO does not calculate the decimal part properly to display
it as micro (in this case microlux). It only calculates the module to
obtain the decimal part from a resolution that is 10000 times the
provided in the datasheet (0.5376 lux/cnt for the veml6030). The
resulting value must still be multiplied by 100 to make it micro.
This bug was introduced with the original implementation of the driver.
Only the illuminance channel is fixed becuase the scale is non sensical
for the intensity channels anyway.
Cc: stable@vger.kernel.org
Fixes: 7b779f573c48 ("iio: light: add driver for veml6030 ambient light sensor")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://patch.msgid.link/20241016-veml6030-fix-processed-micro-v1-1-4a5644796437@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 691e79ffc42154a9c91dc3b7e96a307037b4be74 upstream.
modprobe iio-test-gts and rmmod it, then the following memory leak
occurs:
unreferenced object 0xffffff80c810be00 (size 64):
comm "kunit_try_catch", pid 1654, jiffies 4294913981
hex dump (first 32 bytes):
02 00 00 00 08 00 00 00 20 00 00 00 40 00 00 00 ........ ...@...
80 00 00 00 00 02 00 00 00 04 00 00 00 08 00 00 ................
backtrace (crc a63d875e):
[<0000000028c1b3c2>] kmemleak_alloc+0x34/0x40
[<000000001d6ecc87>] __kmalloc_noprof+0x2bc/0x3c0
[<00000000393795c1>] devm_iio_init_iio_gts+0x4b4/0x16f4
[<0000000071bb4b09>] 0xffffffdf052a62e0
[<000000000315bc18>] 0xffffffdf052a6488
[<00000000f9dc55b5>] kunit_try_run_case+0x13c/0x3ac
[<00000000175a3fd4>] kunit_generic_run_threadfn_adapter+0x80/0xec
[<00000000f505065d>] kthread+0x2e8/0x374
[<00000000bbfb0e5d>] ret_from_fork+0x10/0x20
unreferenced object 0xffffff80cbfe9e70 (size 16):
comm "kunit_try_catch", pid 1658, jiffies 4294914015
hex dump (first 16 bytes):
10 00 00 00 40 00 00 00 80 00 00 00 00 00 00 00 ....@...........
backtrace (crc 857f0cb4):
[<0000000028c1b3c2>] kmemleak_alloc+0x34/0x40
[<000000001d6ecc87>] __kmalloc_noprof+0x2bc/0x3c0
[<00000000393795c1>] devm_iio_init_iio_gts+0x4b4/0x16f4
[<0000000071bb4b09>] 0xffffffdf052a62e0
[<000000007d089d45>] 0xffffffdf052a6864
[<00000000f9dc55b5>] kunit_try_run_case+0x13c/0x3ac
[<00000000175a3fd4>] kunit_generic_run_threadfn_adapter+0x80/0xec
[<00000000f505065d>] kthread+0x2e8/0x374
[<00000000bbfb0e5d>] ret_from_fork+0x10/0x20
......
It includes 5*5 times "size 64" memory leaks, which correspond to 5 times
test_init_iio_gain_scale() calls with gts_test_gains size 10 (10*size(int))
and gts_test_itimes size 5. It also includes 5*1 times "size 16"
memory leak, which correspond to one time __test_init_iio_gain_scale()
call with gts_test_gains_gain_low size 3 (3*size(int)) and gts_test_itimes
size 5.
The reason is that the per_time_gains[i] is not freed which is allocated in
the "gts->num_itime" for loop in iio_gts_build_avail_scale_table().
Cc: stable@vger.kernel.org
Fixes: 38416c28e168 ("iio: light: Add gain-time-scale helpers")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://patch.msgid.link/20241011095512.3667549-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
iio_gts_build_avail_scale_table()
commit 369f05688911b05216cfcd6ca74473bec87948d7 upstream.
If per_time_scales[i] or per_time_gains[i] kcalloc fails in the for loop
of iio_gts_build_avail_scale_table(), the err_free_out will fail to call
kfree() each time when i is reduced to 0, so all the per_time_scales[0]
and per_time_gains[0] will not be freed, which will cause memory leaks.
Fix it by checking if i >= 0.
Cc: stable@vger.kernel.org
Fixes: 38416c28e168 ("iio: light: Add gain-time-scale helpers")
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241016012453.2013302-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efa353ae1b0541981bc96dbf2e586387d0392baa upstream.
In the ad7124_write_raw() function, parameter val can potentially
be zero. This may lead to a division by zero when DIV_ROUND_CLOSEST()
is called within ad7124_set_channel_odr(). The ad7124_write_raw()
function is invoked through the sequence: iio_write_channel_raw() ->
iio_write_channel_attribute() -> iio_channel_write(), with no checks
in place to ensure val is non-zero.
Cc: stable@vger.kernel.org
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20241022134330.574601-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6bd301819f8f69331a55ae2336c8b111fc933f3d upstream.
In the ad9832_write_frequency() function, clk_get_rate() might return 0.
This can lead to a division by zero when calling ad9832_calc_freqreg().
The check if (fout > (clk_get_rate(st->mclk) / 2)) does not protect
against the case when fout is 0. The ad9832_write_frequency() function
is called from ad9832_write(), and fout is derived from a text buffer,
which can contain any value.
Link: https://lore.kernel.org/all/2024100904-CVE-2024-47663-9bdc@gregkh/
Fixes: ea707584bac1 ("Staging: IIO: DDS: AD9832 / AD9835 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20241022134354.574614-1-quzicheng@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7245012f0f496162dd95d888ed2ceb5a35170f1a upstream.
If more than 255 colocated APs exist for the set of all
APs found during 2.4/5 GHz scanning, then the 6 GHz scan
construction will loop forever since the loop variable
has type u8, which can never reach the number found when
that's bigger than 255, and is stored in a u32 variable.
Also move it into the loops to have a smaller scope.
Using a u32 there is fine, we limit the number of APs in
the scan list and each has a limit on the number of RNR
entries due to the frame size. With a limit of 1000 scan
results, a frame size upper bound of 4096 (really it's
more like ~2300) and a TBTT entry size of at least 11,
we get an upper bound for the number of ~372k, well in
the bounds of a u32.
Cc: stable@vger.kernel.org
Fixes: eae94cf82d74 ("iwlwifi: mvm: add support for 6GHz")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219375
Link: https://patch.msgid.link/20241023091744.f4baed5c08a1.I8b417148bbc8c5d11c101e1b8f5bf372e17bf2a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07c90acb071b9954e1fecb1e4f4f13d12c544b34 upstream.
iwl4965 fails upon resume from hibernation on my laptop. The reason
seems to be a stale interrupt which isn't being cleared out before
interrupts are enabled. We end up with a race beween the resume
trying to bring things back up, and the restart work (queued form
the interrupt handler) trying to bring things down. Eventually
the whole thing blows up.
Fix the problem by clearing out any stale interrupts before
interrupts get enabled during resume.
Here's a debug log of the indicent:
[ 12.042589] ieee80211 phy0: il_isr ISR inta 0x00000080, enabled 0xaa00008b, fh 0x00000000
[ 12.042625] ieee80211 phy0: il4965_irq_tasklet inta 0x00000080, enabled 0x00000000, fh 0x00000000
[ 12.042651] iwl4965 0000:10:00.0: RF_KILL bit toggled to enable radio.
[ 12.042653] iwl4965 0000:10:00.0: On demand firmware reload
[ 12.042690] ieee80211 phy0: il4965_irq_tasklet End inta 0x00000000, enabled 0xaa00008b, fh 0x00000000, flags 0x00000282
[ 12.052207] ieee80211 phy0: il4965_mac_start enter
[ 12.052212] ieee80211 phy0: il_prep_station Add STA to driver ID 31: ff:ff:ff:ff:ff:ff
[ 12.052244] ieee80211 phy0: il4965_set_hw_ready hardware ready
[ 12.052324] ieee80211 phy0: il_apm_init Init card's basic functions
[ 12.052348] ieee80211 phy0: il_apm_init L1 Enabled; Disabling L0S
[ 12.055727] ieee80211 phy0: il4965_load_bsm Begin load bsm
[ 12.056140] ieee80211 phy0: il4965_verify_bsm Begin verify bsm
[ 12.058642] ieee80211 phy0: il4965_verify_bsm BSM bootstrap uCode image OK
[ 12.058721] ieee80211 phy0: il4965_load_bsm BSM write complete, poll 1 iterations
[ 12.058734] ieee80211 phy0: __il4965_up iwl4965 is coming up
[ 12.058737] ieee80211 phy0: il4965_mac_start Start UP work done.
[ 12.058757] ieee80211 phy0: __il4965_down iwl4965 is going down
[ 12.058761] ieee80211 phy0: il_scan_cancel_timeout Scan cancel timeout
[ 12.058762] ieee80211 phy0: il_do_scan_abort Not performing scan to abort
[ 12.058765] ieee80211 phy0: il_clear_ucode_stations Clearing ucode stations in driver
[ 12.058767] ieee80211 phy0: il_clear_ucode_stations No active stations found to be cleared
[ 12.058819] ieee80211 phy0: _il_apm_stop Stop card, put in low power state
[ 12.058827] ieee80211 phy0: _il_apm_stop_master stop master
[ 12.058864] ieee80211 phy0: il4965_clear_free_frames 0 frames on pre-allocated heap on clear.
[ 12.058869] ieee80211 phy0: Hardware restart was requested
[ 16.132299] iwl4965 0000:10:00.0: START_ALIVE timeout after 4000ms.
[ 16.132303] ------------[ cut here ]------------
[ 16.132304] Hardware became unavailable upon resume. This could be a software issue prior to suspend or a hardware issue.
[ 16.132338] WARNING: CPU: 0 PID: 181 at net/mac80211/util.c:1826 ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132390] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
[ 16.132456] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Not tainted 6.11.0-cl+ #143
[ 16.132460] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
[ 16.132463] Workqueue: async async_run_entry_fn
[ 16.132469] RIP: 0010:ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132501] Code: da 02 00 00 c6 83 ad 05 00 00 00 48 89 df e8 98 1b fc ff 85 c0 41 89 c7 0f 84 e9 02 00 00 48 c7 c7 a0 e6 48 a0 e8 d1 77 c4 e0 <0f> 0b eb 2d 84 c0 0f 85 8b 01 00 00 c6 87 ad 05 00 00 00 e8 69 1b
[ 16.132504] RSP: 0018:ffffc9000029fcf0 EFLAGS: 00010282
[ 16.132507] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: 0000000000000001
[ 16.132509] RDX: ffffffff81f21a18 RSI: 0000000000000086 RDI: 0000000000000001
[ 16.132510] RBP: ffff8880072003c0 R08: 0000000000000000 R09: 0000000000000003
[ 16.132512] R10: 0000000000000000 R11: ffff88807e5b0000 R12: 0000000000000001
[ 16.132514] R13: 0000000000000000 R14: 0000000000000000 R15: 00000000ffffff92
[ 16.132515] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
[ 16.132517] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.132519] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
[ 16.132521] Call Trace:
[ 16.132525] <TASK>
[ 16.132526] ? __warn+0x77/0x120
[ 16.132532] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132564] ? report_bug+0x15c/0x190
[ 16.132568] ? handle_bug+0x36/0x70
[ 16.132571] ? exc_invalid_op+0x13/0x60
[ 16.132573] ? asm_exc_invalid_op+0x16/0x20
[ 16.132579] ? ieee80211_reconfig+0x8f/0x14b0 [mac80211]
[ 16.132611] ? snd_hdac_bus_init_cmd_io+0x24/0x200 [snd_hda_core]
[ 16.132617] ? pick_eevdf+0x133/0x1c0
[ 16.132622] ? check_preempt_wakeup_fair+0x70/0x90
[ 16.132626] ? wakeup_preempt+0x4a/0x60
[ 16.132628] ? ttwu_do_activate.isra.0+0x5a/0x190
[ 16.132632] wiphy_resume+0x79/0x1a0 [cfg80211]
[ 16.132675] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
[ 16.132697] dpm_run_callback+0x75/0x1b0
[ 16.132703] device_resume+0x97/0x200
[ 16.132707] async_resume+0x14/0x20
[ 16.132711] async_run_entry_fn+0x1b/0xa0
[ 16.132714] process_one_work+0x13d/0x350
[ 16.132718] worker_thread+0x2be/0x3d0
[ 16.132722] ? cancel_delayed_work_sync+0x70/0x70
[ 16.132725] kthread+0xc0/0xf0
[ 16.132729] ? kthread_park+0x80/0x80
[ 16.132732] ret_from_fork+0x28/0x40
[ 16.132735] ? kthread_park+0x80/0x80
[ 16.132738] ret_from_fork_asm+0x11/0x20
[ 16.132741] </TASK>
[ 16.132742] ---[ end trace 0000000000000000 ]---
[ 16.132930] ------------[ cut here ]------------
[ 16.132932] WARNING: CPU: 0 PID: 181 at net/mac80211/driver-ops.c:41 drv_stop+0xe7/0xf0 [mac80211]
[ 16.132957] Modules linked in: ctr ccm sch_fq_codel xt_tcpudp xt_multiport xt_state iptable_filter iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 ip_tables x_tables binfmt_misc joydev mousedev btusb btrtl btintel btbcm bluetooth ecdh_generic ecc iTCO_wdt i2c_dev iwl4965 iwlegacy coretemp snd_hda_codec_analog pcspkr psmouse mac80211 snd_hda_codec_generic libarc4 sdhci_pci cqhci sha256_generic sdhci libsha256 firewire_ohci snd_hda_intel snd_intel_dspcfg mmc_core snd_hda_codec snd_hwdep firewire_core led_class iosf_mbi snd_hda_core uhci_hcd lpc_ich crc_itu_t cfg80211 ehci_pci ehci_hcd snd_pcm usbcore mfd_core rfkill snd_timer snd usb_common soundcore video parport_pc parport intel_agp wmi intel_gtt backlight e1000e agpgart evdev
[ 16.133014] CPU: 0 UID: 0 PID: 181 Comm: kworker/u8:6 Tainted: G W 6.11.0-cl+ #143
[ 16.133018] Tainted: [W]=WARN
[ 16.133019] Hardware name: Hewlett-Packard HP Compaq 6910p/30BE, BIOS 68MCU Ver. F.19 07/06/2010
[ 16.133021] Workqueue: async async_run_entry_fn
[ 16.133025] RIP: 0010:drv_stop+0xe7/0xf0 [mac80211]
[ 16.133048] Code: 48 85 c0 74 0e 48 8b 78 08 89 ea 48 89 de e8 e0 87 04 00 65 ff 0d d1 de c4 5f 0f 85 42 ff ff ff e8 be 52 c2 e0 e9 38 ff ff ff <0f> 0b 5b 5d c3 0f 1f 40 00 41 54 49 89 fc 55 53 48 89 f3 2e 2e 2e
[ 16.133050] RSP: 0018:ffffc9000029fc50 EFLAGS: 00010246
[ 16.133053] RAX: 0000000000000000 RBX: ffff8880072008e0 RCX: ffff88800377f6c0
[ 16.133054] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff8880072008e0
[ 16.133056] RBP: 0000000000000000 R08: ffffffff81f238d8 R09: 0000000000000000
[ 16.133058] R10: ffff8880080520f0 R11: 0000000000000000 R12: ffff888008051c60
[ 16.133060] R13: ffff8880072008e0 R14: 0000000000000000 R15: ffff8880072011d8
[ 16.133061] FS: 0000000000000000(0000) GS:ffff88807c200000(0000) knlGS:0000000000000000
[ 16.133063] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 16.133065] CR2: 000055dd43786c08 CR3: 000000000978f000 CR4: 00000000000006f0
[ 16.133067] Call Trace:
[ 16.133069] <TASK>
[ 16.133070] ? __warn+0x77/0x120
[ 16.133075] ? drv_stop+0xe7/0xf0 [mac80211]
[ 16.133098] ? report_bug+0x15c/0x190
[ 16.133100] ? handle_bug+0x36/0x70
[ 16.133103] ? exc_invalid_op+0x13/0x60
[ 16.133105] ? asm_exc_invalid_op+0x16/0x20
[ 16.133109] ? drv_stop+0xe7/0xf0 [mac80211]
[ 16.133132] ieee80211_do_stop+0x55a/0x810 [mac80211]
[ 16.133161] ? fq_codel_reset+0xa5/0xc0 [sch_fq_codel]
[ 16.133164] ieee80211_stop+0x4f/0x180 [mac80211]
[ 16.133192] __dev_close_many+0xa2/0x120
[ 16.133195] dev_close_many+0x90/0x150
[ 16.133198] dev_close+0x5d/0x80
[ 16.133200] cfg80211_shutdown_all_interfaces+0x40/0xe0 [cfg80211]
[ 16.133223] wiphy_resume+0xb2/0x1a0 [cfg80211]
[ 16.133247] ? wiphy_suspend+0x2a0/0x2a0 [cfg80211]
[ 16.133269] dpm_run_callback+0x75/0x1b0
[ 16.133273] device_resume+0x97/0x200
[ 16.133277] async_resume+0x14/0x20
[ 16.133280] async_run_entry_fn+0x1b/0xa0
[ 16.133283] process_one_work+0x13d/0x350
[ 16.133287] worker_thread+0x2be/0x3d0
[ 16.133290] ? cancel_delayed_work_sync+0x70/0x70
[ 16.133294] kthread+0xc0/0xf0
[ 16.133296] ? kthread_park+0x80/0x80
[ 16.133299] ret_from_fork+0x28/0x40
[ 16.133302] ? kthread_park+0x80/0x80
[ 16.133304] ret_from_fork_asm+0x11/0x20
[ 16.133307] </TASK>
[ 16.133308] ---[ end trace 0000000000000000 ]---
[ 16.133335] ieee80211 phy0: PM: dpm_run_callback(): wiphy_resume [cfg80211] returns -110
[ 16.133360] ieee80211 phy0: PM: failed to restore async: error -110
Cc: stable@vger.kernel.org
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241001200745.8276-1-ville.syrjala@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e15d84b3bba187aa372dff7c58ce1fd5cb48a076 upstream.
In the current logic, memory is allocated for storing the MSDU context
during management packet TX but this memory is not being freed during
management TX completion. Similar leaks are seen in the management TX
cleanup logic.
Kmemleak reports this problem as below,
unreferenced object 0xffffff80b64ed250 (size 16):
comm "kworker/u16:7", pid 148, jiffies 4294687130 (age 714.199s)
hex dump (first 16 bytes):
00 2b d8 d8 80 ff ff ff c4 74 e9 fd 07 00 00 00 .+.......t......
backtrace:
[<ffffffe6e7b245dc>] __kmem_cache_alloc_node+0x1e4/0x2d8
[<ffffffe6e7adde88>] kmalloc_trace+0x48/0x110
[<ffffffe6bbd765fc>] ath10k_wmi_tlv_op_gen_mgmt_tx_send+0xd4/0x1d8 [ath10k_core]
[<ffffffe6bbd3eed4>] ath10k_mgmt_over_wmi_tx_work+0x134/0x298 [ath10k_core]
[<ffffffe6e78d5974>] process_scheduled_works+0x1ac/0x400
[<ffffffe6e78d60b8>] worker_thread+0x208/0x328
[<ffffffe6e78dc890>] kthread+0x100/0x1c0
[<ffffffe6e78166c0>] ret_from_fork+0x10/0x20
Free the memory during completion and cleanup to fix the leak.
Protect the mgmt_pending_tx idr_remove() operation in
ath10k_wmi_tlv_op_cleanup_mgmt_tx_send() using ar->data_lock similar to
other instances.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Fixes: dc405152bb64 ("ath10k: handle mgmt tx completion event")
Fixes: c730c477176a ("ath10k: Remove msdu from idr when management pkt send fails")
Cc: stable@vger.kernel.org
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://patch.msgid.link/20241015064103.6060-1-quic_mpubbise@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
EnhancedPrefetchScheduleAccelerationFinal DCN35"
commit 1b6063a57754eae5705753c01e78dc268b989038 upstream.
This reverts
commit 9dad21f910fc ("drm/amd/display: update DML2 policy EnhancedPrefetchScheduleAccelerationFinal DCN35")
[why & how]
The offending commit exposes a hang with lid close/open behavior.
Both issues seem to be related to ODM 2:1 mode switching, so there
is another issue generic to that sequence that needs to be
investigated.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 68bf95317ebf2cfa7105251e4279e951daceefb7)
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a71892cbcdb9d1459c84f5a4c722b14354158a5 upstream.
This reverts commit 15fffc6a5624b13b428bb1c6e9088e32a55eb82c.
This commit causes a regression, so revert it for now until it can come
back in a way that works for everyone.
Link: https://lore.kernel.org/all/172790598832.1168608.4519484276671503678.stgit@dwillia2-xfh.jf.intel.com/
Fixes: 15fffc6a5624 ("driver core: Fix uevent_show() vs driver detach race")
Cc: stable <stable@kernel.org>
Cc: Ashish Sangwan <a.sangwan@samsung.com>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rafael J. Wysocki <rafael@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31004740e42846a6f0bb255e6348281df3eb8032 upstream.
Use pm_runtime_put in the remove function and pm_runtime_get to disable
RPM on platforms that don't support runtime D3, as re-enabling it through
sysfs auto power control may cause the controller to malfunction. This
can lead to issues such as hotplug devices not being detected due to
failed interrupt generation.
Fixes: a5d6264b638e ("xhci: Enable RPM on controllers that support low-power states")
Cc: stable <stable@kernel.org>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241024133718.723846-1-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 075919f6df5dd82ad0b1894898b315fbb3c29b84 upstream.
During the aborting of a command, the software receives a command
completion event for the command ring stopped, with the TRB pointing
to the next TRB after the aborted command.
If the command we abort is located just before the Link TRB in the
command ring, then during the 'command ring stopped' completion event,
the xHC gives the Link TRB in the event's cmd DMA, which causes a
mismatch in handling command completion event.
To address this situation, move the 'command ring stopped' completion
event check slightly earlier, since the specific command it stopped
on isn't of significant concern.
Fixes: 7f84eef0dafb ("USB: xhci: No-op command queueing and irq handler.")
Cc: stable@vger.kernel.org
Signed-off-by: Faisal Hassan <quic_faisalh@quicinc.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20241022155631.1185-1-quic_faisalh@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34c21f94fa1e147a19b54b6adf0c93a623b70dd8 upstream.
Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation")
removed most users of the platform device driver data from the
qcom-qmp-usb driver, but mistakenly also removed the initialisation
despite the data still being used in the runtime PM callbacks. This bug
was later reproduced when the driver was copied to create the qmp-usbc
driver.
Restore the driver data initialisation at probe to avoid a NULL-pointer
dereference on runtime suspend.
Apparently no one uses runtime PM, which currently needs to be enabled
manually through sysfs, with these drivers.
Fixes: 19281571a4d5 ("phy: qcom: qmp-usb: split USB-C PHY driver")
Cc: stable@vger.kernel.org # 6.9
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-4-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 29240130ab77c80bea1464317ae2a5fd29c16a0c upstream.
Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation")
removed most users of the platform device driver data from the
qcom-qmp-usb driver, but mistakenly also removed the initialisation
despite the data still being used in the runtime PM callbacks. This bug
was later reproduced when the driver was copied to create the
qmp-usb-legacy driver.
Restore the driver data initialisation at probe to avoid a NULL-pointer
dereference on runtime suspend.
Apparently no one uses runtime PM, which currently needs to be enabled
manually through sysfs, with these drivers.
Fixes: e464a3180a43 ("phy: qcom-qmp-usb: split off the legacy USB+dp_com support")
Cc: stable@vger.kernel.org # 6.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bd9e4d4a3b127686efc60096271b0a44c3100061 upstream.
Commit 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation")
removed most users of the platform device driver data, but mistakenly
also removed the initialisation despite the data still being used in the
runtime PM callbacks.
Restore the driver data initialisation at probe to avoid a NULL-pointer
dereference on runtime suspend.
Apparently no one uses runtime PM, which currently needs to be enabled
manually through sysfs, with this driver.
Fixes: 413db06c05e7 ("phy: qcom-qmp-usb: clean up probe initialisation")
Cc: stable@vger.kernel.org # 6.2
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240911115253.10920-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b8423a2f5814dbf055ed7c41f25bfe91c2066cbe upstream.
If drm_dp_hpd_bridge_register() fails, the probe function returns
without removing the fwnode via fwnode_handle_put(), leaking the
resource.
Jump to fwnode_remove if drm_dp_hpd_bridge_register() fails to remove
the fwnode acquired with device_get_named_child_node().
Cc: stable@vger.kernel.org
Fixes: 7d9f1b72b296 ("usb: typec: qcom-pmic-typec: switch to DRM_AUX_HPD_BRIDGE")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-2-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7f02b8a5b602098f2901166e7e4d583acaed872a upstream.
The right function to release a fwnode acquired via
device_get_named_child_node() is fwnode_handle_put(), and not
fwnode_remove_software_node(), as no software node is being handled.
Replace the calls to fwnode_remove_software_node() with
fwnode_handle_put() in qcom_pmic_typec_probe() and
qcom_pmic_typec_remove().
Cc: stable@vger.kernel.org
Fixes: a4422ff22142 ("usb: typec: qcom: Add Qualcomm PMIC Type-C driver")
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241020-qcom_pmic_typec-fwnode_remove-v2-1-7054f3d2e215@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
self-powered devices
commit afb92ad8733ef0a2843cc229e4d96aead80bc429 upstream.
PD3.1 spec ("8.3.3.3.3 PE_SNK_Wait_for_Capabilities State") mandates
that the policy engine perform a hard reset when SinkWaitCapTimer
expires. Instead the code explicitly does a GET_SOURCE_CAP when the
timer expires as part of SNK_WAIT_CAPABILITIES_TIMEOUT. Due to this the
following compliance test failures are reported by the compliance tester
(added excerpts from the PD Test Spec):
* COMMON.PROC.PD.2#1:
The Tester receives a Get_Source_Cap Message from the UUT. This
message is valid except the following conditions: [COMMON.PROC.PD.2#1]
a. The check fails if the UUT sends this message before the Tester
has established an Explicit Contract
...
* TEST.PD.PROT.SNK.4:
...
4. The check fails if the UUT does not send a Hard Reset between
tTypeCSinkWaitCap min and max. [TEST.PD.PROT.SNK.4#1] The delay is
between the VBUS present vSafe5V min and the time of the first bit
of Preamble of the Hard Reset sent by the UUT.
For the purpose of interoperability, restrict the quirk introduced in
https://lore.kernel.org/all/20240523171806.223727-1-sebastian.reichel@collabora.com/
to only non self-powered devices as battery powered devices will not
have the issue mentioned in that commit.
Cc: stable@vger.kernel.org
Fixes: 122968f8dda8 ("usb: typec: tcpm: avoid resets for missing source capability messages")
Reported-by: Badhri Jagan Sridharan <badhri@google.com>
Closes: https://lore.kernel.org/all/CAPTae5LAwsVugb0dxuKLHFqncjeZeJ785nkY4Jfd+M-tCjHSnQ@mail.gmail.com/
Signed-off-by: Amit Sunil Dhamne <amitsd@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241024022233.3276995-1-amitsd@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9581acb91eaf5bbe70086bbb6fca808220d358ba upstream.
The 'altmodes_node' fwnode_handle is never released after it is no
longer required, which leaks the resource.
Add the required call to fwnode_handle_put() when 'altmodes_node' is no
longer required.
Cc: stable@vger.kernel.org
Fixes: 7b458a4c5d73 ("usb: typec: Add typec_port_register_altmodes()")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20241021-typec-class-fwnode_handle_put-v2-1-3281225d3d27@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fdce49b5da6e0fb6d077986dec3e90ef2b094b50 upstream.
For devm_usb_put_phy(), its comment says it needs to invoke usb_put_phy()
to release the phy, but it does not do that actually, so it can not fully
undo what the API devm_usb_get_phy() does, that is wrong, fixed by using
devres_release() instead of devres_destroy() within the API.
Fixes: cedf8602373a ("usb: phy: move bulk of otg/otg.c to phy/phy.c")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241020-usb_phy_fix-v1-1-7f79243b8e1e@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a95d28a8a2f76c591a195c06ea15f5b15c66c3d1 upstream.
This ID appears to be RTL8188SU, not RTL8192DU. This is the wrong driver
for RTL8188SU. The r8712u driver from staging handles this ID.
I think this ID comes from the original rtl8192du driver from Realtek.
I don't know if they added it by mistake, or it was actually used for
two different chips.
RTL8188SU with this ID exists in the wild. RTL8192DU with this ID
probably doesn't.
Fixes: b5dc8873b6ff ("wifi: rtlwifi: Add rtl8192du/sw.c")
Cc: stable@vger.kernel.org # v6.11
Closes: https://github.com/lwfinger/rtl8192du/issues/105
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/40245564-41fe-4a5e-881f-cd517255b20a@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b983b271662bd6104d429b0fd97af3333ba760bf ]
Disabling preemption in the GRU driver is unnecessary, and clashes with
sleeping locks in several code paths. Remove preempt_disable and
p |
