| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit f36199355c64a39fe82cfddc7623d827c7e050da ]
Maurizio found a race where the abort and cmd stop paths can race as
follows:
1. thread1 runs iscsit_release_commands_from_conn and sets
CMD_T_FABRIC_STOP.
2. thread2 runs iscsit_aborted_task and then does __iscsit_free_cmd. It
then returns from the aborted_task callout and we finish
target_handle_abort and do:
target_handle_abort -> transport_cmd_check_stop_to_fabric ->
lio_check_stop_free -> target_put_sess_cmd
The cmd is now freed.
3. thread1 now finishes iscsit_release_commands_from_conn and runs
iscsit_free_cmd while accessing a command we just released.
In __target_check_io_state we check for CMD_T_FABRIC_STOP and set the
CMD_T_ABORTED if the driver is not cleaning up the cmd because of a session
shutdown. However, iscsit_release_commands_from_conn only sets the
CMD_T_FABRIC_STOP and does not check to see if the abort path has claimed
completion ownership of the command.
This adds a check in iscsit_release_commands_from_conn so only the abort or
fabric stop path cleanup the command.
Link: https://lore.kernel.org/r/1605318378-9269-1-git-send-email-michael.christie@oracle.com
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fe0a8a95e7134d0b44cd407bc0085b9ba8d8fe31 ]
iSCSI NOPs are sometimes "lost", mistakenly sent to the user-land iscsid
daemon instead of handled in the kernel, as they should be, resulting in a
message from the daemon like:
iscsid: Got nop in, but kernel supports nop handling.
This can occur because of the new forward- and back-locks, and the fact
that an iSCSI NOP response can occur before processing of the NOP send is
complete. This can result in "conn->ping_task" being NULL in
iscsi_nop_out_rsp(), when the pointer is actually in the process of being
set.
To work around this, we add a new state to the "ping_task" pointer. In
addition to NULL (not assigned) and a pointer (assigned), we add the state
"being set", which is signaled with an INVALID pointer (using "-1").
Link: https://lore.kernel.org/r/20201106193317.16993-1-leeman.duncan@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e773ca7da8beeca7f17fe4c9d1284a2b66839cc1 ]
Actually, burst size is equal to '1 << desc->rqcfg.brst_size'.
we should use burst size, not desc->rqcfg.brst_size.
dma memcpy performance on Rockchip RV1126
@ 1512MHz A7, 1056MHz LPDDR3, 200MHz DMA:
dmatest:
/# echo dma0chan0 > /sys/module/dmatest/parameters/channel
/# echo 4194304 > /sys/module/dmatest/parameters/test_buf_size
/# echo 8 > /sys/module/dmatest/parameters/iterations
/# echo y > /sys/module/dmatest/parameters/norandom
/# echo y > /sys/module/dmatest/parameters/verbose
/# echo 1 > /sys/module/dmatest/parameters/run
dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
Before:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 48 iops 200338 KB/s (0)
After this patch:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 179 iops 734873 KB/s (0)
After this patch and increase dma clk to 400MHz:
dmatest: dma0chan0-copy0: summary 8 tests, 0 failures 259 iops 1062929 KB/s (0)
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Link: https://lore.kernel.org/r/1605326106-55681-1-git-send-email-sugar.zhang@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f0d2c876c96d4908a9ef40959a44bec21bdd6cf ]
If Doorbell Buffer Config command fails even 'dev->dbbuf_dbs != NULL'
which means OACS indicates that NVME_CTRL_OACS_DBBUF_SUPP is set,
nvme_dbbuf_update_and_check_event() will check event even it's not been
successfully set.
This patch fixes mismatch among dbbuf for sq/cqs in case that dbbuf
command fails.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7940fb035abd88040d56be209962feffa33b03d0 ]
The battery status is also being reported by the logitech-hidpp driver,
so ignore the standard HID battery status to avoid reporting the same
info twice.
Note the logitech-hidpp battery driver provides more info, such as properly
differentiating between charging and discharging. Also the standard HID
battery info seems to be wrong, reporting a capacity of just 26% after
fully charging the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ba2df09f1500d3f27398a3382b86d39c3e6abe2 ]
The xilinx_dma_poll_timeout macro is sometimes called while holding a
spinlock (see xilinx_dma_issue_pending() for an example) this means we
shouldn't sleep when polling the dma channel registers. To address it
in xilinx poll timeout macro use readl_poll_timeout_atomic instead of
readl_poll_timeout variant.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1604473206-32573-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f59ee399de4a8ca4d7d19cdcabb4b63e94867f09 ]
Kernel 5.4 introduces HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE, devices need to
be set explicitly with this flag.
Signed-off-by: Chris Ye <lzye@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 34a9fa2025d9d3177c99351c7aaf256c5f50691f ]
Some HID devices don't use a report ID because they only have a single
report. In those cases, the report ID in struct hid_report will be zero
and the data for the report will start at the first byte, so don't skip
over the first byte.
Signed-off-by: Pablo Ceballos <pceballos@google.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1884583fcd17d6a1b1bba94bbb5826e6b5c6e17 ]
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201008112628.3979-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1811977cb11354aef8cbd13e35ff50db716728a4 ]
This device needs HID_QUIRK_MULTI_INPUT in order to be presented to userspace
in a consistent way.
Reported-and-tested-by: David Gámiz Jiménez <david.gamiz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 652f3d00de523a17b0cebe7b90debccf13aa8c31 ]
The Varmilo VA104M Keyboard (04b4:07b1, reported as Varmilo Z104M)
exposes media control hotkeys as a USB HID consumer control device, but
these keys do not work in the current (5.8-rc1) kernel due to the
incorrect HID report descriptor. Fix the problem by modifying the
internal HID report descriptor.
More specifically, the keyboard report descriptor specifies the
logical boundary as 572~10754 (0x023c ~ 0x2a02) while the usage
boundary is specified as 0~10754 (0x00 ~ 0x2a02). This results in an
incorrect interpretation of input reports, causing inputs to be ignored.
By setting the Logical Minimum to zero, we align the logical boundary
with the Usage ID boundary.
Some notes:
* There seem to be multiple variants of the VA104M keyboard. This
patch specifically targets 04b4:07b1 variant.
* The device works out-of-the-box on Windows platform with the generic
consumer control device driver (hidserv.inf). This suggests that
Windows either ignores the Logical Minimum/Logical Maximum or
interprets the Usage ID assignment differently from the linux
implementation; Maybe there are other devices out there that only
works on Windows due to this problem?
Signed-off-by: Frank Yang <puilp0502@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit de9f8eea5a44b0b756d3d6345af7f8e630a3c8c0 upstream.
Unfortunately, it appears our fix in:
commit b5d29843d8ef ("drm/atomic_helper: Allow DPMS On<->Off changes
for unregistered connectors")
Which attempted to work around the problems introduced by:
commit 4d80273976bf ("drm/atomic_helper: Disallow new modesets on
unregistered connectors")
Is still not the right solution, as modesets can still be triggered
outside of drm_atomic_set_crtc_for_connector().
So in order to fix this, while still being careful that we don't break
modesets that a driver may perform before being registered with
userspace, we replace connector->registered with a tristate member,
connector->registration_state. This allows us to keep track of whether
or not a connector is still initializing and hasn't been exposed to
userspace, is currently registered and exposed to userspace, or has been
legitimately removed from the system after having once been present.
Using this info, we can prevent userspace from performing new modesets
on unregistered connectors while still allowing the driver to perform
modesets on unregistered connectors before the driver has finished being
registered.
Changes since v1:
- Fix WARN_ON() in drm_connector_cleanup() that CI caught with this
patchset in igt@drv_module_reload@basic-reload-inject and
igt@drv_module_reload@basic-reload by checking if the connector is
registered instead of unregistered, as calling drm_connector_cleanup()
on a connector that hasn't been registered with userspace yet should
stay valid.
- Remove unregistered_connector_check(), and just go back to what we
were doing before in commit 4d80273976bf ("drm/atomic_helper: Disallow
new modesets on unregistered connectors") except replacing
READ_ONCE(connector->registered) with drm_connector_is_unregistered().
This gets rid of the behavior of allowing DPMS On<->Off, but that should
be fine as it's more consistent with the UAPI we had before - danvet
- s/drm_connector_unregistered/drm_connector_is_unregistered/ - danvet
- Update documentation, fix some typos.
Fixes: b5d29843d8ef ("drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016203946.9601-1-lyude@redhat.com
(cherry picked from commit 39b50c603878f4f8ae541ac4088a805d588abc79)
Fixes: e96550956fbc ("drm/atomic_helper: Disallow new modesets on unregistered connectors")
Fixes: 34ca26a98ad6 ("drm/atomic_helper: Allow DPMS On<->Off changes for unregistered connectors")
Cc: stable@vger.kernel.org
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f117cb854a44a79898d844e6ae3fd23bd94e786 upstream.
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5c042b23f7429e5c2ac987b01a31c69059a978b upstream.
Workaround regulators whose supply name happens to be the same as its
own name. This fixes boards that used to work before the early supply
resolving was removed. The error message is left in place so that
offending drivers can be detected.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/d703acde2a93100c3c7a81059d716c50ad1b1f52.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4b639e254d3d4f15ee4ff2b890a447204cfbeea9 upstream.
When a regulator's name equals its supply's name the
regulator_resolve_supply() recurses indefinitely. Add a check
so that debugging the problem is easier. The "fixed" commit
just exposed the problem.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/c6171057cfc0896f950c4d8cb82df0f9f1b89ad9.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 57a6ad482af256b2a13de14194fb8f67c1a65f10 upstream.
Fixed commit introduced a possible second call to
set_machine_constraints() and that allocates memory for
rdev->constraints. Move the allocation to the caller so
it's easier to manage and done once.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator")
Cc: stable@vger.kernel.org
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1
Link: https://lore.kernel.org/r/78c3d4016cebc08d441aad18cb924b4e4d9cf9df.1605226675.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 365ec8b61689bd64d6a61e129e0319bf71336407 upstream.
Limit the fsl,pfuze-support-disable-sw to the pfuze100 and pfuze200
variants.
When enabling fsl,pfuze-support-disable-sw and using a pfuze3000 or
pfuze3001, the driver would choose pfuze100_sw_disable_regulator_ops
instead of the newly introduced and correct pfuze3000_sw_regulator_ops.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Fixes: 6f1cf5257acc ("regualtor: pfuze100: correct sw1a/sw2 on pfuze3000")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201110174113.2066534-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e5b1032a656e9aa4c7a4df77cb9156a2a651a5f9 upstream.
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 KXCJ91008-s
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read by a special HingeAngleService
process; and this process calls a DSM (Device Specific Method) on the
ACPI KIOX010A device node for the sensor in the display, to let the
embedded-controller (EC) know about the mode so that it can disable the
kbd and touchpad to avoid spurious input while folded into tablet-mode.
This notifying of the EC is problematic because sometimes the EC comes up
thinking that device is in tablet-mode and the kbd and touchpad do not
work. This happens for example on Irbis NB111 devices after a suspend /
resume cycle (after a complete battery drain / hard reset without having
booted Windows at least once). Other 2-in-1s which are likely affected
too are e.g. the Teclast F5 and F6 series.
The kxcjk-1013 driver may seem like a strange place to deal with this,
but since it is *the* driver for the ACPI KIOX010A device, it is also
the driver which has access to the ACPI handle needed by the DSM.
Add support for calling the DSM and on probe unconditionally tell the
EC that the device is laptop mode, fixing the kbd and touchpad sometimes
not working.
Fixes: 7f6232e69539 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-3-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11e94f28c3de35d5ad1ac6a242a5b30f4378991a upstream.
Replace the boolean is_smo8500_device variable with an acpi_type enum.
For now this can be either ACPI_GENERIC or ACPI_SMO8500, this is a
preparation patch for adding special handling for the KIOX010A ACPI HID,
which will add a ACPI_KIOX010A acpi_type to the introduced enum.
For stable as needed as precursor for next patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: 7f6232e69539 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID")
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201110133835.129080-2-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aee9dccc5b64e878cf1b18207436e73f66d74157 upstream.
Add 024c:0627 to the list of SDIO device-ids, based on hardware found in
the wild. This hardware exists on at least some Acer SW1-011 tablets.
Signed-off-by: Brian O'Keefe <bokeefe@alum.wpi.edu>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/b9e1523f-2ba7-fb82-646a-37f095b4440e@alum.wpi.edu
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e67c139c488e84e7eae6c333231e791f0e89b3fb upstream.
For below code, there has chance to cause deadlock in SMP system:
Thread 1:
clk_enable_lock();
pr_info("debug message");
clk_enable_unlock();
Thread 2:
imx_uart_console_write()
clk_enable()
clk_enable_lock();
Thread 1:
Acuired clk enable_lock -> printk -> console_trylock_spinning
Thread 2:
console_unlock() -> imx_uart_console_write -> clk_disable -> Acquite clk enable_lock
So the patch is to keep console port clocks always on like
other console drivers.
Fixes: 1cf93e0d5488 ("serial: imx: remove the uart_console() check")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20201111025136.29818-1-fugang.duan@nxp.com
Cc: stable <stable@vger.kernel.org>
[fix up build warning - gregkh]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d4122754442799187d5d537a9c039a49a67e57f1 upstream.
Speakup has only one speakup_tty variable to store the tty it is managing. This
makes sense since its codebase currently assumes that there is only one user who
controls the screen reading.
That however means that we have to forbid using the line discipline several
times, otherwise the second closure would try to free a NULL ldisc_data, leading to
general protection fault: 0000 [#1] SMP KASAN PTI
RIP: 0010:spk_ttyio_ldisc_close+0x2c/0x60
Call Trace:
tty_ldisc_release+0xa2/0x340
tty_release_struct+0x17/0xd0
tty_release+0x9d9/0xcc0
__fput+0x231/0x740
task_work_run+0x12c/0x1a0
do_exit+0x9b5/0x2230
? release_task+0x1240/0x1240
? __do_page_fault+0x562/0xa30
do_group_exit+0xd5/0x2a0
__x64_sys_exit_group+0x35/0x40
do_syscall_64+0x89/0x2b0
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Cc: stable@vger.kernel.org
Reported-by: 秦世松 <qinshisong1205@gmail.com>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Shisong Qin <qinshisong1205@gmail.com>
Link: https://lore.kernel.org/r/20201110183541.fzgnlwhjpgqzjeth@function
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2ba546ebe0ce2af47833d8912ced9b4a579f13cb ]
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efebd ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d003868d7f8579838ed58b6429af91844039b6f8 ]
Use correct bittiming limits for the KCAN CAN controller.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20201115163027.16851-2-jimmyassarsson@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6654b57866b98230a270953dd34f67de17ab1708 ]
Fix to return a negative error code from the error handling case instead
of 0 in function sun8i_dw_hdmi_bind().
Fixes: b7c7436a5ff0 ("drm/sun4i: Implement A83T HDMI driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1605488969-5211-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cd0d83eab2e0c26fe87a10debfedbb23901853c1 ]
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a68cc0d690c9e5730d676b764c6f059343b842c ]
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
can_put_echo_skb()
[ Upstream commit 81c9c8e0adef3285336b942f93287c554c89e6c6 ]
The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7968c7c79d3be8987feb8021f0c46e6866831408 ]
In the error handling, we should goto the probe_exit_candev
to free ndev to prevent memory leak.
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201114111708.3465543-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1e654070a60d5d4f7cce59c38f4ca790bb79121 ]
netif_rx() is meant to be called from interrupt contexts. can_restart() may be
called by can_restart_work(), which is called from a worqueue, so it may run in
process context. Use netif_rx_ni() instead.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Co-developed-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Loris Fauster <loris.fauster@ttcontrol.com>
Signed-off-by: Alejandro Concepcion Rodriguez <alejandro@acoro.eu>
Link: https://lore.kernel.org/r/4e84162b-fb31-3a73-fa9a-9438b4bd5234@acoro.eu
[mkl: use netif_rx_ni() instead of netif_rx_any_context()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c2e14b48119b39446031d29d994044ae958d8fc ]
Currently, we may set the tunnel option flag when the size of metadata
is zero. For example, we set TUNNEL_GENEVE_OPT in the receive function
no matter the geneve option is present or not. As this may result in
issues on the tunnel flags consumers, this patch fixes the issue.
Related discussion:
* https://lore.kernel.org/netdev/1604448694-19351-1-git-send-email-yihung.wei@gmail.com/T/#u
Fixes: 256c87c17c53 ("net: check tunnel option type in tunnel flags")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Link: https://lore.kernel.org/r/1605053800-74072-1-git-send-email-yihung.wei@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 676650d007e06fddcf3fe38238251d71bd179641 ]
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b0a ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33b6c39e747c552fa770eecebd1776f1f4a222b1 ]
The "revid" is used to store negative error codes so it should be an int
type.
Fixes: e27c729219ad ("Input: add driver for ADXL345/346 Digital Accelerometers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20201026072824.GA1620546@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7daaa06357bf7f1874b62bb1ea9d66a51d4e567e ]
The Medion Akoya E2228T's ACPI _LID implementation is quite broken,
it has the same issues as the one from the Medion Akoya E2215T:
1. For notifications it uses an ActiveLow Edge GpioInt, rather then
an ActiveBoth one, meaning that the device is only notified when the
lid is closed, not when it is opened.
2. Matching with this its _LID method simply always returns 0 (closed)
In order for the Linux LID code to work properly with this implementation,
the lid_init_state selection needs to be set to ACPI_BUTTON_LID_INIT_OPEN,
add a DMI quirk for this.
While working on this I also found out that the MD60### part of the model
number differs per country/batch while all of the E2215T and E2228T models
have this issue, so also remove the " MD60198" part from the E2215T quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit da3fecb0040324c08f1587e5bff1f15f36be1872 ]
The scsi_block_reqs_cnt increased in ufshcd_hold() is supposed to be
decreased back in ufshcd_ungate_work() in a paired way. However, if
specific ufshcd_hold/release sequences are met, it is possible that
scsi_block_reqs_cnt is increased twice but only one ungate work is
queued. To make sure scsi_block_reqs_cnt is handled by ufshcd_hold() and
ufshcd_ungate_work() in a paired way, increase it only if queue_work()
returns true.
Link: https://lore.kernel.org/r/1604384682-15837-2-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 63fbf8013b2f6430754526ef9594f229c7219b1f ]
There need to enable pclk_gpio when do irq_create_mapping, since it will
do access to gpio controller.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d5179458d22dc0b4fdc724e4bed4231a655112a ]
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5a4 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df8d85d8c69d6837817e54dcb73c84a8b5a13877 ]
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 470b74758260e4abc2508cf1614573c00a00465c ]
Currently when QoS is enabled for VF and any min_rate is configured,
the driver sets bw_share value to at least 1 and doesn’t allow to set
it to 0 to make minimal rate unlimited. It means there is always a
minimal rate configured for every VF, even if user tries to remove it.
In order to make QoS disable possible, check whether all vports have
configured min_rate = 0. If this is true, set their bw_share to 0 to
disable min_rate limitations.
Fixes: c9497c98901c ("net/mlx5: Add support for setting VF min rate")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3beb9be165083c2964eba1923601c3bfac0b02d4 ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3ced0a88cd4c ("qlcnic: Add support to run firmware POST")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605248186-16013-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb47d16ea21045c66eebbf5ed792e74a8537e27a ]
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 469981b17a4f ("qed: Add unaligned and packed packet processing")
Fixes: fcb39f6c10b2 ("qed: Add mpa buffer descriptors for storing and processing mpa fpdus")
Fixes: 1e28eaad07ea ("qed: Add iWARP support for fpdu spanned over more than two tcp packets")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Link: https://lore.kernel.org/r/1605532033-27373-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fc70f5bf5e525dde81565f0a30d5e39168062eba ]
During rmnet unregistration, the real device rx_handler is first cleared
followed by the removal of rx_handler_data after the rcu synchronization.
Any packets in the receive path may observe that the rx_handler is NULL.
However, there is no check when dereferencing this value to use the
rmnet_port information.
This fixes following splat by adding the NULL check.
Unable to handle kernel NULL pointer dereference at virtual
address 000000000000000d
pc : rmnet_rx_handler+0x124/0x284
lr : rmnet_rx_handler+0x124/0x284
rmnet_rx_handler+0x124/0x284
__netif_receive_skb_core+0x758/0xd74
__netif_receive_skb+0x50/0x17c
process_backlog+0x15c/0x1b8
napi_poll+0x88/0x284
net_rx_action+0xbc/0x23c
__do_softirq+0x20c/0x48c
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Link: https://lore.kernel.org/r/1605298325-3705-1-git-send-email-subashab@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6d9c8d15af0ef20a66a0b432cac0d08319920602 ]
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded604365 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 92307069a96c07d9b6e74b96b79390e7cd7d2111 ]
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data re |
