| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit e01b042e580f1fbf4fd8da467442451da00c7a90 upstream.
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Fixes: f3240e2811f0 ("stmmac: remove warning when compile as built-in (V2)")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Link: https://lore.kernel.org/r/20220224033536.25056-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fadead80fe4c033b5e514fcbadd20b55c4494112 upstream.
Commit c503e63200c6 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200c6 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6ba5273d4ede03d075d7a116b8edad1f6115f4d upstream.
The VF can be configured via the PF's ndo ops at the same time the PF is
receiving/handling virtchnl messages. This has many issues, with
one of them being the ndo op could be actively resetting a VF (i.e.
resetting it to the default state and deleting/re-adding the VF's VSI)
while a virtchnl message is being handled. The following error was seen
because a VF ndo op was used to change a VF's trust setting while the
VIRTCHNL_OP_CONFIG_VSI_QUEUES was ongoing:
[35274.192484] ice 0000:88:00.0: Failed to set LAN Tx queue context, error: ICE_ERR_PARAM
[35274.193074] ice 0000:88:00.0: VF 0 failed opcode 6, retval: -5
[35274.193640] iavf 0000:88:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 6
Fix this by making sure the virtchnl handling and VF ndo ops that
trigger VF resets cannot run concurrently. This is done by adding a
struct mutex cfg_lock to each VF structure. For VF ndo ops, the mutex
will be locked around the critical operations and VFR. Since the ndo ops
will trigger a VFR, the virtchnl thread will use mutex_trylock(). This
is done because if any other thread (i.e. VF ndo op) has the mutex, then
that means the current VF message being handled is no longer valid, so
just ignore it.
This issue can be seen using the following commands:
for i in {0..50}; do
rmmod ice
modprobe ice
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
sleep 2
echo 0 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 0 > /sys/class/net/ens785f1/device/sriov_numvfs
sleep 1
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
echo 1 > /sys/class/net/ens785f1/device/sriov_numvfs
ip link set ens785f1 vf 0 trust on
ip link set ens785f0 vf 0 trust on
done
Fixes: 7c710869d64e ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ffd24fa2fcc76ecb2e61e7a4ef8588177bcb42a6 upstream.
Update MAC type check e1000_pch_tgp because for e1000_pch_cnp,
NVM checksum update is still possible.
Emit a more detailed warning message.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1191663
Fixes: 4051f68318ca ("e1000e: Do not take care about recovery NVM checksum")
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d5081bf5dcfb1cb83fb538708b0ac07a10a79cc4 upstream.
The field offset for port configuration status on SPR has been changed to
bit 14 from ICX where it resides at bit 12. By chance link status detection
continued to work on SPR. This is due to bit 12 being a configuration bit
which is in sync with the status bit. Fix this by checking for a SPR device
and checking correct status bit.
Fixes: 26bfe3d0b227 ("ntb: intel: Add Icelake (gen4) support for Intel NTB")
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5838a14832d447990827d85e90afe17e6fb9c175 upstream.
Do not call get_trip_hyst() from thermal_genl_cmd_tz_get_trip() if
the thermal zone does not define one.
Fixes: 1ce50e7d408e ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcf4ff7a48e7598e6b10126cc02177abb8ae4f3f upstream.
xennet_destroy_queues() relies on info->netdev->real_num_tx_queues to
delete queues. Since d7dac083414eb5bb99a6d2ed53dc2c1b405224e5
("net-sysfs: update the queue counts in the unregistration path"),
unregister_netdev() indirectly sets real_num_tx_queues to 0. Those two
facts together means, that xennet_destroy_queues() called from
xennet_remove() cannot do its job, because it's called after
unregister_netdev(). This results in kfree-ing queues that are still
linked in napi, which ultimately crashes:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 52 Comm: xenwatch Tainted: G W 5.16.10-1.32.fc32.qubes.x86_64+ #226
RIP: 0010:free_netdev+0xa3/0x1a0
Code: ff 48 89 df e8 2e e9 00 00 48 8b 43 50 48 8b 08 48 8d b8 a0 fe ff ff 48 8d a9 a0 fe ff ff 49 39 c4 75 26 eb 47 e8 ed c1 66 ff <48> 8b 85 60 01 00 00 48 8d 95 60 01 00 00 48 89 ef 48 2d 60 01 00
RSP: 0000:ffffc90000bcfd00 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88800edad000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffc90000bcfc30 RDI: 00000000ffffffff
RBP: fffffffffffffea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88800edad050
R13: ffff8880065f8f88 R14: 0000000000000000 R15: ffff8880066c6680
FS: 0000000000000000(0000) GS:ffff8880f3300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000e998c006 CR4: 00000000003706e0
Call Trace:
<TASK>
xennet_remove+0x13d/0x300 [xen_netfront]
xenbus_dev_remove+0x6d/0xf0
__device_release_driver+0x17a/0x240
device_release_driver+0x24/0x30
bus_remove_device+0xd8/0x140
device_del+0x18b/0x410
? _raw_spin_unlock+0x16/0x30
? klist_iter_exit+0x14/0x20
? xenbus_dev_request_and_reply+0x80/0x80
device_unregister+0x13/0x60
xenbus_dev_changed+0x18e/0x1f0
xenwatch_thread+0xc0/0x1a0
? do_wait_intr_irq+0xa0/0xa0
kthread+0x16b/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Fix this by calling xennet_destroy_queues() from xennet_uninit(),
when real_num_tx_queues is still available. This ensures that queues are
destroyed when real_num_tx_queues is set to 0, regardless of how
unregister_netdev() was called.
Originally reported at
https://github.com/QubesOS/qubes-issues/issues/7257
Fixes: d7dac083414eb5bb9 ("net-sysfs: update the queue counts in the unregistration path")
Cc: stable@vger.kernel.org
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08783aa7693f55619859f4f63f384abf17cb58c5 upstream.
This JSP2 PCH actually seems to be some special Apple
specific ICP variant rather than a JSP. Make it so. Or at
least all the references to it seem to be some Apple ICL
machines. Didn't manage to find these PCI IDs in any
public chipset docs unfortunately.
The only thing we're losing here with this JSP->ICP change
is Wa_14011294188, but based on the HSD that isn't actually
needed on any ICP based design (including JSP), only TGP
based stuff (including MCC) really need it. The documented
w/a just never made that distinction because Windows didn't
want to differentiate between JSP and MCC (not sure how
they handle hpd/ddc/etc. then though...).
Cc: stable@vger.kernel.org
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4226
Fixes: 943682e3bd19 ("drm/i915: Introduce Jasper Lake PCH")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224132142.12927-1-ville.syrjala@linux.intel.com
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Tested-by: Tomas Bzatek <bugs@bzatek.net>
(cherry picked from commit 53581504a8e216d435f114a4f2596ad0dfd902fc)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ce97f4ec5e0f8726a5dda1710727b1ee9badcac upstream.
The AMD IOMMU logs I/O page faults and such to a ring buffer in
system memory, and this ring buffer can overflow. The AMD IOMMU
spec has the following to say about the interrupt status bit that
signals this overflow condition:
EventOverflow: Event log overflow. RW1C. Reset 0b. 1 = IOMMU
event log overflow has occurred. This bit is set when a new
event is to be written to the event log and there is no usable
entry in the event log, causing the new event information to
be discarded. An interrupt is generated when EventOverflow = 1b
and MMIO Offset 0018h[EventIntEn] = 1b. No new event log
entries are written while this bit is set. Software Note: To
resume logging, clear EventOverflow (W1C), and write a 1 to
MMIO Offset 0018h[EventLogEn].
The AMD IOMMU driver doesn't currently implement this recovery
sequence, meaning that if a ring buffer overflow occurs, logging
of EVT/PPR/GA events will cease entirely.
This patch implements the spec-mandated reset sequence, with the
minor tweak that the hardware seems to want to have a 0 written to
MMIO Offset 0018h[EventLogEn] first, before writing an 1 into this
field, or the IOMMU won't actually resume logging events.
Signed-off-by: Lennert Buytenhek <buytenh@arista.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YVrSXEdW2rzEfOvk@wantstofly.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dcf0c838854c86e1f41fb1934aea906845d69782 upstream.
The get_boot_hartid_from_fdt() function currently returns U32_MAX
for failure case which is not correct because U32_MAX is a valid
hartid value. This patch fixes the issue by returning error code.
Cc: <stable@vger.kernel.org>
Fixes: d7071743db31 ("RISC-V: Add EFI stub support.")
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c1a66c3bc425ff93774fb2f6eefa67b83170dd7e ]
Workstation application ANSA/META v21.1.4 get this error dmesg when
running CI test suite provided by ANSA/META:
[drm:amdgpu_gem_va_ioctl [amdgpu]] *ERROR* Couldn't update BO_VA (-16)
This is caused by:
1. create a 256MB buffer in invisible VRAM
2. CPU map the buffer and access it causes vm_fault and try to move
it to visible VRAM
3. force visible VRAM space and traverse all VRAM bos to check if
evicting this bo is valuable
4. when checking a VM bo (in invisible VRAM), amdgpu_vm_evictable()
will set amdgpu_vm->evicting, but latter due to not in visible
VRAM, won't really evict it so not add it to amdgpu_vm->evicted
5. before next CS to clear the amdgpu_vm->evicting, user VM ops
ioctl will pass amdgpu_vm_ready() (check amdgpu_vm->evicted)
but fail in amdgpu_vm_bo_update_mapping() (check
amdgpu_vm->evicting) and get this error log
This error won't affect functionality as next CS will finish the
waiting VM ops. But we'd better clear the error log by checking
the amdgpu_vm->evicting flag in amdgpu_vm_ready() to stop calling
amdgpu_vm_bo_update_mapping() later.
Another reason is amdgpu_vm->evicted list holds all BOs (both
user buffer and page table), but only page table BOs' eviction
prevent VM ops. amdgpu_vm->evicting flag is set only for page
table BOs, so we should use evicting flag instead of evicted list
in amdgpu_vm_ready().
The side effect of this change is: previously blocked VM op (user
buffer in "evicted" list but no page table in it) gets done
immediately.
v2: update commit comments.
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Qiang Yu <qiang.yu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f6b0f2d037c8864f20ff15311c695f65eb09db5 ]
The f_CNT register (at the PCI config. address 0x78) is 16-bit, not
8-bit! The bug was there from the very start... :-(
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d3d079bde07e1b7deaeb57506dc0b86010121d17 ]
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 501e38a5531efbd77d5c73c0ba838a889bfc1d74 upstream.
dev->config and dev->hs_config and dev->dev need to be cleaned if
dev_config fails to avoid UAF.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20211231172138.7993-3-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 89f3594d0de58e8a57d92d497dea9fee3d4b9cda upstream.
dev->buf does not need to be released if it already exists before
executing dev_config.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20211231172138.7993-2-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 21e8a96377e6b6debae42164605bf9dcbe5720c5 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5de717974005fcad2502281e9f82e139ca91f4bb ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b0dcb3882c8f08bdeafa03adb4487e104d26050 ]
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 455896c53d5b803733ddd84e1bf8a430644439b6 ]
pm_runtime_get_() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Yongzhi Liu <lyz_cs@pku.edu.cn>
Link: https://lore.kernel.org/r/1642311296-87020-1-git-send-email-lyz_cs@pku.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40 ]
Buttonpads are expected to map the INPUT_PROP_BUTTONPAD property bit
and the BTN_LEFT key bit.
As explained in the specification, where a device has a button type
value of 0 (click-pad) or 1 (pressure-pad) there should not be
discrete buttons:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/touchpad-windows-precision-touchpad-collection#device-capabilities-feature-report
However, some drivers map the BTN_RIGHT and/or BTN_MIDDLE key bits even
though the device is a buttonpad and therefore does not have those
buttons.
This behavior has forced userspace applications like libinput to
implement different workarounds and quirks to detect buttonpads and
offer to the user the right set of features and configuration options.
For more information:
https://gitlab.freedesktop.org/libinput/libinput/-/merge_requests/726
In order to avoid this issue clear the BTN_RIGHT and BTN_MIDDLE key
bits when the input device is register if the INPUT_PROP_BUTTONPAD
property bit is set.
Notice that this change will not affect udev because it does not check
for buttons. See systemd/src/udev/udev-builtin-input_id.c.
List of known affected hardware:
- Chuwi AeroBook Plus
- Chuwi Gemibook
- Framework Laptop
- GPD Win Max
- Huawei MateBook 2020
- Prestigio Smartbook 141 C2
- Purism Librem 14v1
- StarLite Mk II - AMI firmware
- StarLite Mk II - Coreboot firmware
- StarLite Mk III - AMI firmware
- StarLite Mk III - Coreboot firmware
- StarLabTop Mk IV - AMI firmware
- StarLabTop Mk IV - Coreboot firmware
- StarBook Mk V
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20220208174806.17183-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e2a354e3775870ca823f1fb29bbbffbe11059a6 ]
The check done by regulator_late_cleanup() to detect whether a regulator
is on was inconsistent with the check done by _regulator_is_enabled().
While _regulator_is_enabled() takes the enable GPIO into account,
regulator_late_cleanup() was not doing that.
This resulted in a false positive, e.g. when a GPIO-controlled fixed
regulator was used, which was not enabled at boot time, e.g.
reg_disp_1v2: reg_disp_1v2 {
compatible = "regulator-fixed";
regulator-name = "display_1v2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
gpio = <&tlmm 148 0>;
enable-active-high;
};
Such regulator doesn't have an is_enabled() operation. Nevertheless
it's state can be determined based on the enable GPIO. The check in
regulator_late_cleanup() wrongly assumed that the regulator is on and
tried to disable it.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Link: https://lore.kernel.org/r/20220208084645.8686-1-oliver.barta@aptiv.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9495b9b31abe525ebd93da58de2c88b9f66d3a0e ]
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cacfddf82baf1470e5741edeecb187260868f195 ]
In mac80211_hwsim, the probe_req frame is created and sent while
scanning. It is sent with ieee80211_tx_info which is not initialized.
Uninitialized ieee80211_tx_info can cause problems when using
mac80211_hwsim with wmediumd. wmediumd checks the tx_rates field of
ieee80211_tx_info and doesn't relay probe_req frame to other clients
even if it is a broadcasting message.
Call ieee80211_tx_prepare_skb() to initialize ieee80211_tx_info for
the probe_req that is created by hw_scan_work in mac80211_hwsim.
Signed-off-by: JaeMan Park <jaeman@google.com>
Link: https://lore.kernel.org/r/20220113060235.546107-1-jaeman@google.com
[fix memory leak]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 42a79960ffa50bfe9e0bf5d6280be89bf563a5dd ]
Add IEEE80211_TX_STAT_NOACK_TRANSMITTED to tx_status flags to have proper
statistics for non-acked frames.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Link: https://lore.kernel.org/r/20220111221327.1499881-1-benjamin.beichler@uni-rostock.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d1e972ace42390de739cde87d96043dcbe502286 upstream.
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
Fixes: 5b2b135a87fc ("gpio: Add Tegra186 support")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20220211093904.1112679-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a2ab75b8e76e455af7867e3835fd9cdf386b508f upstream.
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c19d93542a6081577e6da9bf5e887979c72e80c1 upstream.
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 96b169f05cdcc844b400695184d77e42071d14f2 upstream.
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a7415 ("tty: n_gsm: avoid recursive locking with async port hangup")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3b7468f082d106459e86e8dc6fb9bdd65553433 upstream.
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 737b0ef3be6b319d6c1fd64193d1603311969326 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3abea10e6a8f0e7804ed4c124bea2d15aca977c8 upstream.
It is easy to hit the below memory leaks in my TigerLake platform:
unreferenced object 0xffff927c8b91dbc0 (size 32):
comm "kworker/0:2", pid 112, jiffies 4294893323 (age 83.604s)
hex dump (first 32 bytes):
4e 41 4d 45 3d 49 4e 54 33 34 30 30 20 54 68 65 NAME=INT3400 The
72 6d 61 6c 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b a5 rmal.kkkkkkkkkk.
backtrace:
[<ffffffff9c502c3e>] __kmalloc_track_caller+0x2fe/0x4a0
[<ffffffff9c7b7c15>] kvasprintf+0x65/0xd0
[<ffffffff9c7b7d6e>] kasprintf+0x4e/0x70
[<ffffffffc04cb662>] int3400_notify+0x82/0x120 [int3400_thermal]
[<ffffffff9c8b7358>] acpi_ev_notify_dispatch+0x54/0x71
[<ffffffff9c88f1a7>] acpi_os_execute_deferred+0x17/0x30
[<ffffffff9c2c2c0a>] process_one_work+0x21a/0x3f0
[<ffffffff9c2c2e2a>] worker_thread+0x4a/0x3b0
[<ffffffff9c2cb4dd>] kthread+0xfd/0x130
[<ffffffff9c201c1f>] ret_from_fork+0x1f/0x30
Fix it by calling kfree() accordingly.
Fixes: 38e44da59130 ("thermal: int3400_thermal: process "thermal table changed" event")
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 22e9f71072fa605cbf033158db58e0790101928d upstream.
If the state is not idle then resolve_prepare_src() should immediately
fail and no change to global state should happen. However, it
unconditionally overwrites the src_addr trying to build a temporary any
address.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
Which would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
CPU: 1 PID: 32204 Comm: syz-executor.1 Not tainted 5.12.0-rc8-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x141/0x1d7 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:232
__kasan_report mm/kasan/report.c:399 [inline]
kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:416
__list_add_valid+0x93/0xa0 lib/list_debug.c:26
__list_add include/linux/list.h:67 [inline]
list_add_tail include/linux/list.h:100 [inline]
cma_listen_on_all drivers/infiniband/core/cma.c:2557 [inline]
rdma_listen+0x787/0xe00 drivers/infiniband/core/cma.c:3751
ucma_listen+0x16a/0x210 drivers/infiniband/core/ucma.c:1102
ucma_write+0x259/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xa30 fs/read_write.c:603
ksys_write+0x1ee/0x250 fs/read_write.c:658
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
This is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address derived from the dst build one explicitly on the stack and
bind to that as any other normal flow would do. rdma_bind_addr() will copy
it over the src_addr once it knows the state is valid.
This is similar to commit bc0bdc5afaa7 ("RDMA/cma: Do not change
route.addr.src_addr.ss_family")
Link: https://lore.kernel.org/r/0-v2-e975c8fd9ef2+11e-syz_cma_srcaddr_jgg@nvidia.com
Cc: stable@vger.kernel.org
Fixes: 732d41c545bb ("RDMA/cma: Make the locking for automatic state transition more clear")
Reported-by: syzbot+c94a3675a626f6333d74@syzkaller.appspotmail.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8f7a5484f2188e9af2d9e4e587587d724501b12 upstream.
When unbinding/binding a driver with DMA mapped memory, the DMA map is
not freed before the driver is reloaded. This leads to a memory leak
when the DMA map is overwritten when reprobing the driver.
This can be reproduced with a platform driver having a dma-range:
dummy {
...
#address-cells = <0x2>;
#size-cells = <0x2>;
ranges;
dma-ranges = <...>;
...
};
and then unbinding/binding it:
~# echo soc:dummy >/sys/bus/platform/drivers/<driver>/unbind
DMA map object 0xffffff800b0ae540 still being held by &pdev->dev
~# echo soc:dummy >/sys/bus/platform/drivers/<driver>/bind
~# echo scan > /sys/kernel/debug/kmemleak
~# cat /sys/kernel/debug/kmemleak
unreferenced object 0xffffff800b0ae540 (size 64):
comm "sh", pid 833, jiffies 4295174550 (age 2535.352s)
hex dump (first 32 bytes):
00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 80 00 00 00 00 00 00 00 80 00 00 00 00 ................
backtrace:
[<ffffffefd1694708>] create_object.isra.0+0x108/0x344
[<ffffffefd1d1a850>] kmemleak_alloc+0x8c/0xd0
[<ffffffefd167e2d0>] __kmalloc+0x440/0x6f0
[<ffffffefd1a960a4>] of_dma_get_range+0x124/0x220
[<ffffffefd1a8ce90>] of_dma_configure_id+0x40/0x2d0
[<ffffffefd198b68c>] platform_dma_configure+0x5c/0xa4
[<ffffffefd198846c>] really_probe+0x8c/0x514
[<ffffffefd1988990>] __driver_probe_device+0x9c/0x19c
[<ffffffefd1988cd8>] device_driver_attach+0x54/0xbc
[<ffffffefd1986634>] bind_store+0xc4/0x120
[<ffffffefd19856e0>] drv_attr_store+0x30/0x44
[<ffffffefd173c9b0>] sysfs_kf_write+0x50/0x60
[<ffffffefd173c1c4>] kernfs_fop_write_iter+0x124/0x1b4
[<ffffffefd16a013c>] new_sync_write+0xdc/0x160
[<ffffffefd16a256c>] vfs_write+0x23c/0x2a0
[<ffffffefd16a2758>] ksys_write+0x64/0xec
To prevent this we should free the dma_range_map when the device is
released.
Fixes: e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Cc: stable <stable@vger.kernel.org>
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220216094128.4025861-1-marten.lindahl@axis.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 243a1dd7ba48c120986dd9e66fee74bcb7751034 upstream.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613fb3 ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b328f8002bcf29ef517ee4bf234e09aabec4d2e upstream.
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
Cc: stable@vger.kernel.org
Signed-off-by: Puma Hsu <pumahsu@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84918a89d6efaff075de570b55642b6f4ceeac6d upstream.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e7b0 ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62e3f0afe246720f7646eb1b034a6897dac34405 upstream.
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32fde84362c40961726a5c91f35ad37355ccc0c6 upstream.
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cfc4442c642d568014474b6718ccf65dc7ca6099 upstream.
Add support for the following Telit LE910R1 compositions:
0x701a: rndis, tty, tty, tty
0x701b: ecm, tty, tty, tty
0x9201: tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Link: https://lore.kernel.org/r/20220218134552.4051-1-dnlplm@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ecb3f0b18b320320460a42e40d6fb603f6ded96 upstream.
Dell DW5829e same as DW5821e except CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
There are 2 types product of DW5829e: normal and eSIM.
So we will add 2 PID for DW5829e.
And for each PID, it support MBIM or RMNET.
Let's see test evidence as below:
DW5829e MBIM mode:
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 2
P: Vendor=413c ProdID=81e6 Rev=03.18
S: Manufacturer=Dell Inc.
S: Product=DW5829e Snapdragon X20 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=896mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#=0x1 Alt= 1 #EPs= 2 Cl |
