| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 7b2666ce445c700b8dcee994da44ddcf050a0842 upstream.
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Fixes: 93cacfd41f82 (hwmon: (adt7470) Allow faster removal)
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dba785798526a3282cc4d0f0ea751883715dbbb4 upstream.
When one port's input state get inverted (eg. from low to hight) after
pca953x_irq_setup but before setting irq_mask (by some other driver such as
"gpio-keys"), the next inversion of this port (eg. from hight to low) will not
be triggered any more (because irq_stat is not updated at the first time). Issue
should be fixed after this commit.
Fixes: 89ea8bbe9c3e ("gpio: pca953x.c: add interrupt handling capability")
Signed-off-by: Puyou Lu <puyou.lu@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nfcmrvl_nci_unregister_dev to avoid bugs
commit d270453a0d9ec10bb8a802a142fb1b3601a83098 upstream.
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The first situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... | nfcmrvl_nci_unregister_dev
release_firmware() | nfcmrvl_fw_dnld_abort
kfree(fw) //(1) | fw_dnld_over
| release_firmware
... | kfree(fw) //(2)
| ...
The second situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... |
mod_timer |
(wait a time) |
fw_dnld_timeout | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
... | kfree(fw) //(2)
The third situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_nci_recv_frame |
if(..->fw_download_in_progress)|
nfcmrvl_fw_dnld_recv_frame |
queue_work |
|
fw_dnld_rx_work | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
| kfree(fw) //(2)
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2873d4d52f7c52d60b316ba6c47bd7122b5a9861 upstream.
The previous split budget between TX and RX made it return not using
the entire budget but at the same time not having calling called
napi_complete. This sometimes led to the poll to not be called, and at
the same time having TX and RX interrupts disabled resulting in the
driver getting stuck.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
needs
commit 1e93ed26acf03fe6c97c6d573a10178596aadd43 upstream.
The systemid property was checked for in the wrong place of the device
tree and compared to the wrong value.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-3-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 101da4268626b00d16356a6bf284d66e44c46ff9 upstream.
Use the device of the device tree node should be rather than the
device of the struct net_device when allocating DMA buffers.
The driver got away with it on sparc32 until commit 53b7670e5735
("sparc: factor the dma coherent mapping into helper") after which the
driver oopses.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Link: https://lore.kernel.org/all/20220429084656.29788-2-andreas@gaisler.com
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47f070a63e735bcc8d481de31be1b5a1aa62b31c upstream.
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
(Thread 1) | (Thread 2)
| grcan_reset_timer()
grcan_close() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | grcan_initiate_running_reset()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores")
Cc: stable@vger.kernel.org
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9c10f68e23c13f56685559a0d6fdaca9f838324 upstream.
Read requests that return with NRF error are partially completed in
dasd_eckd_ese_read(). The function keeps track of the amount of
processed bytes and the driver will eventually return this information
back to the block layer for further processing via __dasd_cleanup_cqr()
when the request is in the final stage of processing (from the driver's
perspective).
For this, blk_update_request() is used which requires the number of
bytes to complete the request. As per documentation the nr_bytes
parameter is described as follows:
"number of bytes to complete for @req".
This was mistakenly interpreted as "number of bytes _left_ for @req"
leading to new requests with incorrect data length. The consequence are
inconsistent and completely wrong read requests as data from random
memory areas are read back.
Fix this by correctly specifying the amount of bytes that should be used
to complete the request.
Fixes: 5e6bdd37c552 ("s390/dasd: fix data corruption for thin provisioned devices")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20220505141733.1989450-5-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cd68c48ea15c85f1577a442dc4c285e112ff1b37 upstream.
When reading unformatted tracks on ESE devices, the corresponding memory
areas are simply set to zero for each segment. This is done incorrectly
for blocksizes < 4096.
There are two problems. First, the increment of dst is done using the
counter of the loop (off), which is increased by blksize every
iteration. This leads to a much bigger increment for dst as actually
intended. Second, the increment of dst is done before the memory area
is set to 0, skipping a significant amount of bytes of memory.
This leads to illegal overwriting of memory and ultimately to a kernel
panic.
This is not a problem with 4k blocksize because
blk_queue_max_segment_size is set to PAGE_SIZE, always resulting in a
single iteration for the inner segment loop (bv.bv_len == blksize). The
incorrectly used 'off' value to increment dst is 0 and the correct
memory area is used.
In order to fix this for blksize < 4k, increment dst correctly using the
blksize and only do it at the end of the loop.
Fixes: 5e2b17e712cf ("s390/dasd: Add dynamic formatting support for ESE volumes")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20220505141733.1989450-4-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71f3871657370dbbaf942a1c758f64e49a36c70f upstream.
For ESE devices we get an error for write operations on an unformatted
track. Afterwards the track will be formatted and the IO operation
restarted.
When using alias devices a track might be accessed by multiple requests
simultaneously and there is a race window that a track gets formatted
twice resulting in data loss.
Prevent this by remembering the amount of formatted tracks when starting
a request and comparing this number before actually formatting a track
on the fly. If the number has changed there is a chance that the current
track was finally formatted in between. As a result do not format the
track and restart the current IO to check.
The number of formatted tracks does not match the overall number of
formatted tracks on the device and it might wrap around but this is no
problem. It is only needed to recognize that a track has been formatted at
all in between.
Fixes: 5e2b17e712cf ("s390/dasd: Add dynamic formatting support for ESE volumes")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20220505141733.1989450-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5b53a405e4658580e1faf7c217db3f55a21ba849 upstream.
For ESE devices we get an error when accessing an unformatted track.
The handling of this error will return zero data for read requests and
format the track on demand before writing to it. To do this the code needs
to distinguish between read and write requests. This is done with data from
the blocklayer request. A pointer to the blocklayer request is stored in
the CQR.
If there is an error on the device an ERP request is built to do error
recovery. While the ERP request is mostly a copy of the original CQR the
pointer to the blocklayer request is not copied to not accidentally pass
it back to the blocklayer without cleanup.
This leads to the error that during ESE handling after an ERP request was
built it is not possible to determine the IO direction. This leads to the
formatting of a track for read requests which might in turn lead to data
corruption.
Fixes: 5e2b17e712cf ("s390/dasd: Add dynamic formatting support for ESE volumes")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20220505141733.1989450-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 47f753c1108e287edb3e27fad8a7511a9d55578e upstream.
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7ecbe92b9243edbe94772f6f2c854e4142a3345 upstream.
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9423973869bd4632ffe669f950510c49296656e0 upstream.
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Cc: <stable@vger.kernel.org>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7c81f80246fac44077166f3e07103affe6db8ff upstream.
&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3dfe85fa87b2a26bdbd292b66653bba065cf9941 upstream.
A faulty receiver might report an erroneous channel count. We
should guard against reading beyond AUDIO_CHANNELS_COUNT as
that would overflow the dpcd_pattern_period array.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59bf3557cf2f8a469a554aea1e3d2c8e72a579f7 upstream.
Calculate the appropriate mask for non-size-aligned page selective
invalidation. Since psi uses the mask value to mask out the lower order
bits of the target address, properly flushing the iotlb requires using a
mask value such that [pfn, pfn+pages) all lie within the flushed
size-aligned region. This is not normally an issue because iova.c
always allocates iovas that are aligned to their size. However, iovas
which come from other sources (e.g. userspace via VFIO) may not be
aligned.
To properly flush the IOTLB, both the start and end pfns need to be
equal after applying the mask. That means that the most efficient mask
to use is the index of the lowest bit that is equal where all higher
bits are also equal. For example, if pfn=0x17f and pages=3, then
end_pfn=0x181, so the smallest mask we can use is 8. Any differences
above the highest bit of pages are due to carrying, so by xnor'ing pfn
and end_pfn and then masking out the lower order bits based on pages, we
get 0xffffff00, where the first set bit is the mask we want to use.
Fixes: 6fe1010d6d9c ("vfio/type1: DMA unmap chunking")
Cc: stable@vger.kernel.org
Signed-off-by: David Stevens <stevensd@chromium.org>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20220401022430.1262215-1-stevensd@google.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20220410013533.3959168-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e75f88efac05bf4e107e4171d8db6d8c3937252d upstream.
Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size"
because it clears "size" bits starting from the "start" bit in the according
bitmap. So it has to use "greater" instead of "greater or equal" when performs
bounds check to make sure that GPIOs are in the available range.
Previous implementation skipped ranges that include the last GPIO in
the range.
I wrote the mail to the maintainers
(https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u)
of the questioned DTSes (because I couldn't understand how the maintainers
interpreted this property), but I haven't received a response.
Since the questioned DTSes use "gpio-reserved-ranges = <0 4>"
(i.e., the beginning of the range), this patch doesn't affect these DTSes at all.
TBH this patch doesn't break any existing DTSes because none of them
reserve gpios at the end of range.
Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Andrei Lalaev <andrei.lalaev@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4bc31edebde51fcf8ad0794763b8679a7ecb5ec0 upstream.
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3e5a8e8494a8122fe4eb3f167662f406cab753b9 upstream.
Reset GCC_SDCC_BCR register before every fresh initilazation. This will
reset whole SDHC-msm controller, clears the previous power control
states and avoids, software reset timeout issues as below.
[ 5.458061][ T262] mmc1: Reset 0x1 never completed.
[ 5.462454][ T262] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 5.469065][ T262] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00007202
[ 5.475688][ T262] mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[ 5.482315][ T262] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[ 5.488927][ T262] mmc1: sdhci: Present: 0x01f800f0 | Host ctl: 0x00000000
[ 5.495539][ T262] mmc1: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
[ 5.502162][ T262] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
[ 5.508768][ T262] mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
[ 5.515381][ T262] mmc1: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
[ 5.521996][ T262] mmc1: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[ 5.528607][ T262] mmc1: sdhci: Caps: 0x362dc8b2 | Caps_1: 0x0000808f
[ 5.535227][ T262] mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
[ 5.541841][ T262] mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
[ 5.548454][ T262] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 5.555079][ T262] mmc1: sdhci: Host ctl2: 0x00000000
[ 5.559651][ T262] mmc1: sdhci_msm: ----------- VENDOR REGISTER DUMP-----------
[ 5.566621][ T262] mmc1: sdhci_msm: DLL sts: 0x00000000 | DLL cfg: 0x6000642c | DLL cfg2: 0x0020a000
[ 5.575465][ T262] mmc1: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl: 0x00010800 | DDR cfg: 0x80040873
[ 5.584658][ T262] mmc1: sdhci_msm: Vndr func: 0x00018a9c | Vndr func2 : 0xf88218a8 Vndr func3: 0x02626040
Fixes: 0eb0d9f4de34 ("mmc: sdhci-msm: Initial support for Qualcomm chipsets")
Signed-off-by: Shaik Sajida Bhanu <quic_c_sbhanu@quicinc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1650816153-23797-1-git-send-email-quic_c_sbhanu@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4f7d63287217ba25e5c80f5faae5e4f7118790e upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73029a4d7161f8b6c0934553145ef574d2d0c645 upstream.
gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit deefc58bafb4841df7f0a0d85d89a1c819db9743 upstream.
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 535bf600de75a859698892ee873521a48d289ec1 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 06d5afd4d640eea67f5623e76cd5fc03359b7f3c upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 284260f278b706364fb4c88a7b56ba5298d5973c upstream.
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ec92e9742774bf42614fceea3bf6b50c9409225 upstream.
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa371e96f05dcb36a88298f5cb70aa7234d5e8b8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.8.2 states that both sides will revert to
the non-multiplexed mode via a close-down message (CLD). The usual program
flow is as following:
- start multiplex mode by sending AT+CMUX to the mobile
- establish the control channel (DLCI 0)
- establish user channels (DLCI >0)
- terminate user channels
- send close-down message (CLD)
- revert to AT protocol (i.e. leave multiplexed mode)
The AT protocol is out of scope of the n_gsm driver. However,
gsm_disconnect() sends CLD if gsm_config() detects that the requested
parameters require the mux protocol to restart. The next immediate action
is to start the mux protocol by opening DLCI 0 again. Any responder side
which handles CLD commands correctly forces us to fail at this point
because AT+CMUX needs to be sent to the mobile to start the mux again.
Therefore, remove the CLD command in this phase and keep both sides in
multiplexed mode.
Remove the gsm_disconnect() function as it become unnecessary and merge the
remaining parts into gsm_cleanup_mux() to handle the termination order and
locking correctly.
Fixes: 71e077915396 ("tty: n_gsm: do not send/receive in ldisc close path")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d0f6cfb2bd165b0aa307750e07e03420859bd554 upstream.
Control Flow Integrity (CFI) instrumentation of the kernel noticed that
the caller, dev_attr_show(), and the callback, odvp_show(), did not have
matching function prototypes, which would cause a CFI exception to be
raised. Correct the prototype by using struct device_attribute instead
of struct kobj_attribute.
Reported-and-tested-by: Joao Moreira <joao@overdrivepizza.com>
Link: https://lore.kernel.org/lkml/067ce8bd4c3968054509831fa2347f4f@overdrivepizza.com/
Fixes: 006f006f1e5c ("thermal/int340x_thermal: Export OEM vendor variables")
Cc: 5.8+ <stable@vger.kernel.org> # 5.8+
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5fd1fe4807f91ea0cca043114d929faa11bd4190 upstream.
I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org
Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ae4dd2e26fdfebf0b8c6af6c325383eadfefdb4 upstream.
Fix typo in the _SEL_FETCH_PLANE_BASE_1_B register base address.
Fixes: a5523e2ff074a5 ("drm/i915: Add PSR2 selective fetch registers")
References: https://gitlab.freedesktop.org/drm/intel/-/issues/5400
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v5.9+
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421162221.2261895-1-imre.deak@intel.com
(cherry picked from commit af2cbc6ef967f61711a3c40fca5366ea0bc7fecc)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bc6de2878429e85c1f1afaa566f7b5abb2243eef ]
There is a deadlock in rr_close(), which is shown below:
(Thread 1) | (Thread 2)
| rr_open()
rr_close() | add_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | rr_timer()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417125519.82618-1-duoming@zju.edu.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aeaf59b78712c7a1827c76f086acff4f586e072f ]
This reverts commit 723ad916134784b317b72f3f6cf0f7ba774e5dae
When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
excee |
