| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 2d65ed76924bc772d3974b0894d870b1aa63b34a ]
In ipa_cmd_register_write_valid() we verify that values we will
supply to a REGISTER_WRITE IPA immediate command will fit in
the fields that need to hold them. This patch fixes some issues
in that function and ipa_cmd_register_write_offset_valid().
The dev_err() call in ipa_cmd_register_write_offset_valid() has
some printf format errors:
- The name of the register (corresponding to the string format
specifier) was not supplied.
- The IPA base offset and offset need to be supplied separately to
match the other format specifiers.
Also make the ~0 constant used there to compute the maximum
supported offset value explicitly unsigned.
There are two other issues in ipa_cmd_register_write_valid():
- There's no need to check the hash flush register for platforms
(like IPA v4.2) that do not support hashed tables
- The highest possible endpoint number, whose status register
offset is computed, is COUNT - 1, not COUNT.
Fix these problems, and add some additional commentary.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d5bc5015eb9d64cbd14e467db1a56db1472d0d6c ]
We do not support inter-EE channel or event ring commands. Inter-EE
interrupts are disabled (and never re-enabled) for all channels and
event rings, so we have no need for the GSI registers that clear
those interrupt conditions. So remove their definitions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8a28af7a3e85ddf358f8c41e401a33002f7a9587 ]
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 09078368d516918666a0122f2533dc73676d3d7e ]
ieee80211_find_sta_by_ifaddr() must be called under the RCU lock and
the resulting pointer is only valid under RCU lock as well.
Fix ath10k_wmi_tlv_op_pull_peer_stats_info() to hold RCU lock before it
calls ieee80211_find_sta_by_ifaddr() and release it when the resulting
pointer is no longer needed.
This problem was found while reviewing code to debug RCU warn from
ath10k_wmi_tlv_parse_peer_stats_info().
Link: https://lore.kernel.org/linux-wireless/7230c9e5-2632-b77e-c4f9-10eca557a5bb@linuxfoundation.org/
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210210212107.40373-1-skhan@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 874020f8adce535cd318af1768ffe744251b6593 ]
The only thing we do touching the device in hard interrupt context
is, at most, writing an interrupt ACK register, which isn't racing
in with anything protected by the reg_lock.
Thus, avoid disabling interrupts here for potentially long periods
of time, particularly long periods have been observed with dumping
of firmware memory (leading to lockup warnings on some devices.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210135352.da916ab91298.I064c3e7823b616647293ed97da98edefb9ce9435@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f57ab5b75f7193e194c83616cd104f41c8350f68 ]
Initialize the dummy FIB offload module after debugfs, so that the FIB
module could create its own directory there.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit adba838af159914eb98fcd55bfd3a89c9a7d41a8 ]
This patch fixes a defect that uses incorrect function to access
registers. Use 8 and 32 bit access function to access 8 and 32 bit long
data respectively.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210202055012.8296-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d96968315d7ffbd70d608b29e9bea084210b96d ]
When function return fail to __ath11k_mac_register after success called
ieee80211_register_hw, then it set wiphy->dev.parent to NULL by
SET_IEEE80211_DEV(ar->hw, NULL) in end of __ath11k_mac_register, then
cfg80211_get_drvinfo will be called by below call stack, but the
wiphy->dev.parent is NULL, so kernel crash.
Call stack to cfg80211_get_drvinfo:
NetworkManager 826 [001] 6696.731371: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
ffffffffc107d8f1 cfg80211_get_drvinfo+0x1 (/lib/modules/5.10.0-rc1-wt-ath+/kernel/net/wireless-back/cfg80211.ko)
ffffffff9d8fc529 ethtool_get_drvinfo+0x99 (vmlinux)
ffffffff9d90080e dev_ethtool+0x1dbe (vmlinux)
ffffffff9d8b88f7 dev_ioctl+0xb7 (vmlinux)
ffffffff9d8668de sock_do_ioctl+0xae (vmlinux)
ffffffff9d866d60 sock_ioctl+0x350 (vmlinux)
ffffffff9d2ca30e __x64_sys_ioctl+0x8e (vmlinux)
ffffffff9da0dda3 do_syscall_64+0x33 (vmlinux)
ffffffff9dc0008c entry_SYSCALL_64_after_hwframe+0x44 (vmlinux)
7feb5f673007 __GI___ioctl+0x7 (/lib/x86_64-linux-gnu/libc-2.23.so)
0 [unknown] ([unknown])
Code of cfg80211_get_drvinfo, the pdev which is wiphy->dev.parent is
NULL when kernel crash:
void cfg80211_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
{
struct wireless_dev *wdev = dev->ieee80211_ptr;
struct device *pdev = wiphy_dev(wdev->wiphy);
if (pdev->driver)
....
kernel crash log:
[ 973.619550] ath11k_pci 0000:05:00.0: failed to perform regd update : -16
[ 973.619555] ath11k_pci 0000:05:00.0: ath11k regd update failed: -16
[ 973.619566] ath11k_pci 0000:05:00.0: failed register the radio with mac80211: -16
[ 973.619618] ath11k_pci 0000:05:00.0: failed to create pdev core: -16
[ 973.636035] BUG: kernel NULL pointer dereference, address: 0000000000000068
[ 973.636046] #PF: supervisor read access in kernel mode
[ 973.636050] #PF: error_code(0x0000) - not-present page
[ 973.636054] PGD 800000012452e067 P4D 800000012452e067 PUD 12452d067 PMD 0
[ 973.636064] Oops: 0000 [#1] SMP PTI
[ 973.636072] CPU: 3 PID: 848 Comm: NetworkManager Kdump: loaded Tainted: G W OE 5.10.0-rc1-wt-ath+ #24
[ 973.636076] Hardware name: LENOVO 418065C/418065C, BIOS 83ET63WW (1.33 ) 07/29/2011
[ 973.636161] RIP: 0010:cfg80211_get_drvinfo+0x25/0xd0 [cfg80211]
[ 973.636169] Code: e9 c9 fe ff ff 66 66 66 66 90 55 53 ba 20 00 00 00 48 8b af 08 03 00 00 48 89 f3 48 8d 7e 04 48 8b 45 00 48 8b 80 90 01 00 00 <48> 8b 40 68 48 85 c0 0f 84 8d 00 00 00 48 8b 30 e8 a6 cc 72 c7 48
[ 973.636174] RSP: 0018:ffffaafb4040bbe0 EFLAGS: 00010286
[ 973.636180] RAX: 0000000000000000 RBX: ffffaafb4040bbfc RCX: 0000000000000000
[ 973.636184] RDX: 0000000000000020 RSI: ffffaafb4040bbfc RDI: ffffaafb4040bc00
[ 973.636188] RBP: ffff8a84c9568950 R08: 722d302e30312e35 R09: 74612d74772d3163
[ 973.636192] R10: 3163722d302e3031 R11: 2b6874612d74772d R12: ffffaafb4040bbfc
[ 973.636196] R13: 00007ffe453707c0 R14: ffff8a84c9568000 R15: 0000000000000000
[ 973.636202] FS: 00007fd3d179b940(0000) GS:ffff8a84fa2c0000(0000) knlGS:0000000000000000
[ 973.636206] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 973.636211] CR2: 0000000000000068 CR3: 00000001153b6002 CR4: 00000000000606e0
[ 973.636215] Call Trace:
[ 973.636234] ethtool_get_drvinfo+0x99/0x1f0
[ 973.636246] dev_ethtool+0x1dbe/0x2be0
[ 973.636256] ? mntput_no_expire+0x35/0x220
[ 973.636264] ? inet_ioctl+0x1ce/0x200
[ 973.636274] ? tomoyo_path_number_perm+0x68/0x1d0
[ 973.636282] ? kmem_cache_alloc+0x3cb/0x430
[ 973.636290] ? dev_ioctl+0xb7/0x570
[ 973.636295] dev_ioctl+0xb7/0x570
[ 973.636307] sock_do_ioctl+0xae/0x150
[ 973.636315] ? sock_ioctl+0x350/0x3c0
[ 973.636319] sock_ioctl+0x350/0x3c0
[ 973.636332] ? __x64_sys_ioctl+0x8e/0xd0
[ 973.636339] ? dlci_ioctl_set+0x30/0x30
[ 973.636346] __x64_sys_ioctl+0x8e/0xd0
[ 973.636359] do_syscall_64+0x33/0x80
[ 973.636368] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Sequence of function call when wlan load for success case when function
__ath11k_mac_register return 0:
kworker/u16:3-e 2922 [001] 6696.729734: probe:ieee80211_register_hw: (ffffffffc116ae60)
kworker/u16:3-e 2922 [001] 6696.730210: probe:ieee80211_if_add: (ffffffffc1185cc0)
NetworkManager 826 [001] 6696.731345: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
NetworkManager 826 [001] 6696.731371: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
NetworkManager 826 [001] 6696.731639: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
NetworkManager 826 [001] 6696.731653: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
NetworkManager 826 [001] 6696.732866: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
NetworkManager 826 [001] 6696.732893: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
systemd-udevd 3850 [003] 6696.737199: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
systemd-udevd 3850 [003] 6696.737226: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
NetworkManager 826 [000] 6696.759950: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
NetworkManager 826 [000] 6696.759967: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
NetworkManager 826 [000] 6696.760057: probe:ethtool_get_drvinfo: (ffffffff9d8fc490)
NetworkManager 826 [000] 6696.760062: probe:cfg80211_get_drvinfo: (ffffffffc107d8f0)
After apply this patch, kernel crash gone, and below is the test case's
sequence of function call and log when wlan load with fail by function
ath11k_regd_update, and __ath11k_mac_register return fail:
kworker/u16:5-e 192 [001] 215.174388: probe:ieee80211_register_hw: (ffffffffc1131e60)
kworker/u16:5-e 192 [000] 215.174973: probe:ieee80211_if_add: (ffffffffc114ccc0)
NetworkManager 846 [001] 215.175857: probe:ethtool_get_drvinfo: (ffffffff928fc490)
kworker/u16:5-e 192 [000] 215.175867: probe:ieee80211_unregister_hw: (ffffffffc1131970)
NetworkManager 846 [001] 215.175880: probe:cfg80211_get_drvinfo: (ffffffffc107f8f0)
NetworkManager 846 [001] 215.176105: probe:ethtool_get_drvinfo: (ffffffff928fc490)
NetworkManager 846 [001] 215.176118: probe:cfg80211_get_drvinfo: (ffffffffc107f8f0)
[ 215.175859] ath11k_pci 0000:05:00.0: ath11k regd update failed: -16
NetworkManager 846 [001] 215.196420: probe:ethtool_get_drvinfo: (ffffffff928fc490)
NetworkManager 846 [001] 215.196430: probe:cfg80211_get_drvinfo: (ffffffffc107f8f0)
[ 215.258598] ath11k_pci 0000:05:00.0: failed register the radio with mac80211: -16
[ 215.258613] ath11k_pci 0000:05:00.0: failed to create pdev core: -16
When ath11k_regd_update or ath11k_debugfs_register return fail, function
ieee80211_unregister_hw of mac80211 will be called, then it will wait
untill cfg80211_get_drvinfo finished, the wiphy->dev.parent is not NULL
at this moment, after that, it set wiphy->dev.parent to NULL by
SET_IEEE80211_DEV(ar->hw, NULL) in end of __ath11k_mac_register, so
not happen kernel crash.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608607824-16067-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e862a3e4088070de352fdafe9bd9e3ae0a95a33c ]
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e1caaf8ed22eb700cc47ec353816eee33186c1c ]
This patch fixes the max register value for the regmap.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e096a18867a5a989b510f6999d9c6b6622e8f7b ]
Since 20dd3850bcf8 ("can: Speed up CAN frame receiption by using
ml_priv") the CAN framework uses per device specific data in the AF_CAN
protocol. For this purpose the struct net_device->ml_priv is used. Later
the ml_priv usage in CAN was extended for other users, one of them being
CAN_J1939.
Later in the kernel ml_priv was converted to an union, used by other
drivers. E.g. the tun driver started storing it's stats pointer.
Since tun devices can claim to be a CAN device, CAN specific protocols
will wrongly interpret this pointer, which will cause system crashes.
Mostly this issue is visible in the CAN_J1939 stack.
To fix this issue, we request a dedicated CAN pointer within the
net_device struct.
Reported-by: syzbot+5138c4dd15a0401bec7b@syzkaller.appspotmail.com
Fixes: 20dd3850bcf8 ("can: Speed up CAN frame receiption by using ml_priv")
Fixes: ffd956eef69b ("can: introduce CAN midlayer private and allocate it automatically")
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Fixes: 497a5757ce4e ("tun: switch to net core provided statistics counters")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210223070127.4538-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e77f70e734584e0ad1038e459ed3fd2400f873a ]
This patch moves the CAN driver related infrastructure into a separate subdir.
It will be split into more files in the coming patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7867299cde34e9c2d2c676f2a384a9d5853b914d ]
The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.
Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bac04454ef9fada009f0572576837548b190bf94 ]
When data digest is enabled we should unmap pdu iovec before handling
the data digest pdu.
Signed-off-by: Elad Grupi <elad.grupi@dell.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2046a24ae121cd107929655a6aaf3b8c5beea01f ]
There is a possible chance that some cooling device stats buffer
allocation fails due to very high cooling device max state value.
Later cooling device update sysfs can try to access stats data
for the same cooling device. It will lead to NULL pointer
dereference issue.
Add a NULL pointer check before accessing thermal cooling device
stats data. It fixes the following bug
[ 26.812833] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
[ 27.122960] Call trace:
[ 27.122963] do_raw_spin_lock+0x18/0xe8
[ 27.122966] _raw_spin_lock+0x24/0x30
[ 27.128157] thermal_cooling_device_stats_update+0x24/0x98
[ 27.128162] cur_state_store+0x88/0xb8
[ 27.128166] dev_attr_store+0x40/0x58
[ 27.128169] sysfs_kf_write+0x50/0x68
[ 27.133358] kernfs_fop_write+0x12c/0x1c8
[ 27.133362] __vfs_write+0x54/0x160
[ 27.152297] vfs_write+0xcc/0x188
[ 27.157132] ksys_write+0x78/0x108
[ 27.162050] ksys_write+0xf8/0x108
[ 27.166968] __arm_smccc_hvc+0x158/0x4b0
[ 27.166973] __arm_smccc_hvc+0x9c/0x4b0
[ 27.186005] el0_svc+0x8/0xc
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1607367181-24589-1-git-send-email-manafm@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d2d106fe3badfc3bf0dd3899d1c3f210c7203eab ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.565966] name 'pci-das6402/16'
[ 1.566149] WARNING: CPU: 0 PID: 184 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.568923] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.574200] Call Trace:
[ 1.574722] proc_mkdir+0x18/0x20
[ 1.576629] request_threaded_irq+0xfe/0x160
[ 1.576859] auto_attach+0x60a/0xc40 [cb_pcidas64]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195814.4692-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e5848a3d86f03024ae096478bdb892ab3d79131 ]
request_irq() wont accept a name which contains slash so we need to
repalce it with something else -- otherwise it will trigger a warning
and the entry in /proc/irq/ will not be created
since the .name might be used by userspace and we don't want to break
userspace, so we are changing the parameters passed to request_irq()
[ 1.630764] name 'pci-das1602/16'
[ 1.630950] WARNING: CPU: 0 PID: 181 at fs/proc/generic.c:180 __xlate_proc_name+0x93/0xb0
[ 1.634009] RIP: 0010:__xlate_proc_name+0x93/0xb0
[ 1.639441] Call Trace:
[ 1.639976] proc_mkdir+0x18/0x20
[ 1.641946] request_threaded_irq+0xfe/0x160
[ 1.642186] cb_pcidas_auto_attach+0xf4/0x610 [cb_pcidas]
Suggested-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210315195914.4801-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5999b9e5b1f8a2f5417b755130919b3ac96f5550 ]
Only half of the file is under include guard because terminating #endif
is placed too early.
Link: https://lore.kernel.org/r/YE4snvoW1SuwcXAn@localhost.localdomain
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c8c165dea4c8f5ad67b1240861e4f6c5395fa4ac ]
In st_open(), if STp->in_use is true, STp will be freed by
scsi_tape_put(). However, STp is still used by DEBC_printk() after. It is
better to DEBC_printk() before scsi_tape_put().
Link: https://lore.kernel.org/r/20210311064636.10522-1-lyl2019@mail.ustc.edu.cn
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit beb691e69f4dec7bfe8b81b509848acfd1f0dbf9 ]
vhost_reset_is_le() is vhost_init_is_le(), and in the case of
cross-endian legacy, vhost_init_is_le() depends on vq->user_be.
vq->user_be is set by vhost_disable_cross_endian().
But in vhost_vq_reset(), we have:
vhost_reset_is_le(vq);
vhost_disable_cross_endian(vq);
And so user_be is used before being set.
To fix that, reverse the lines order as there is no other dependency
between them.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: https://lore.kernel.org/r/20210312140913.788592-1-lvivier@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit a846738f8c3788d846ed1f587270d2f2e3d32432 upstream.
The fix for XSA-365 zapped too many of the ->persistent_gnt[] entries.
Ones successfully obtained should not be overwritten, but instead left
for xen_blkbk_unmap_prepare() to pick up and put.
This is XSA-371.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d7047ed6b7214fbabc16d8712a822e256b1aa44 upstream.
In commit 6417f03132a6 ("module: remove never implemented
MODULE_SUPPORTED_DEVICE") the MODULE_SUPPORTED_DEVICE macro was
removed from the kerne entirely. Shortly before this patch was applied
mainline the commit 59ec7b89ed3e ("can: peak_usb: add forgotten
supported devices") was added to net/master. As this would result in a
merge conflict, let's revert this patch.
Fixes: 59ec7b89ed3e ("can: peak_usb: add forgotten supported devices")
Link: https://lore.kernel.org/r/20210320192649.341832-1-mkl@pengutronix.de
Suggested-by: Leon Romanovsky <leon@kernel.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f4f9fc29e56b6fa9d7fa65ec51d3c82aff99c99b upstream.
ns can be NULL at this point, and my move of the check from
the original patch by Chaitanya broke this.
Fixes: 0ec84df4953b ("nvme-core: check ctrl css before setting up zns")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 080bfa1e6d928a5d1f185cc44e5f3c251df06df5 upstream.
This reverts commit 2055a99da8a253a357bdfd359b3338ef3375a26c.
This change rejects legitimate configurations.
A slave doesn't need to exist nor implement ndo_slave_setup.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f658b90977d2e79822a558e48116e059a7e75dec upstream.
IOMMU errors have been reported if WoL is enabled and interface is
brought down. It turned out that the network chip triggers DMA
transfers after the DMA buffers have been freed. For WoL to work we
need to leave rx enabled, therefore simply stop the chip from being
a DMA busmaster.
Fixes: 567ca57faa62 ("r8169: add rtl8169_up")
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a5ca857079ea022e0b1b17fc154f7ad7dbc150f upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8dc7 ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f235a69e59484e382dc31952025b0308efedc17 upstream.
gcc points out an incorrect enum assignment:
drivers/net/ethernet/chelsio/inline_crypto/ch_ktls/chcr_ktls.c: In function 'chcr_ktls_cpl_set_tcb_rpl':
drivers/net/ethernet/chelsio/inline_crypto/ch_ktls/chcr_ktls.c:684:22: warning: implicit conversion from 'enum <anonymous>' to 'enum ch_ktls_open_state' [-Wenum-conversion]
This appears harmless, and should apparently use 'CH_KTLS_OPEN_SUCCESS'
instead of 'false', with the same value '0'.
Fixes: efca3878a5fb ("ch_ktls: Issue if connection offload fails")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3401ecf7fc1b9458a19d42c0e26a228f18ac7dda ]
When kzalloc() returns NULL, no error return code of mpt3sas_base_attach()
is assigned. To fix this bug, r is assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308035241.3288-1-baijiaju1990@gmail.com
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f69953837ca5d98aa983a138dc0b90a411e9c763 ]
When kzalloc() returns NULL to qedi->global_queues[i], no error return code
of qedi_alloc_global_queues() is assigned. To fix this bug, status is
assigned with -ENOMEM in this case.
Link: https://lore.kernel.org/r/20210308033024.27147-1-baijiaju1990@gmail.com
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Acked-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 39c0c8553bfb5a3d108aa47f1256076d507605e3 ]
Calling vha->hw->tgt.tgt_ops->free_cmd() from qlt_xmit_response() is wrong
since the command for which a response is sent must remain valid until the
SCSI target core calls .release_cmd(). It has been observed that the
following scenario triggers a kernel crash:
- qlt_xmit_response() calls qlt_check_reserve_free_req()
- qlt_check_reserve_free_req() returns -EAGAIN
- qlt_xmit_response() calls vha->hw->tgt.tgt_ops->free_cmd(cmd)
- transport_handle_queue_full() tries to retransmit the response
Fix this crash by reverting the patch that introduced it.
Link: https://lore.kernel.org/r/20210320232359.941-2-bvanassche@acm.org
Fixes: 0dcec41acb85 ("scsi: qla2xxx: Make sure that aborted commands are freed")
Cc: Quinn Tran <qutran@marvell.com>
Cc: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eb50aaf960e3bedfef79063411ffd670da94b84b ]
The decrementation of acpi_device_bus_id->instance_no
in acpi_device_del() is incorrect, because it may cause
a duplicate instance number to be allocated next time
a device with the same acpi_device_bus_id is added.
Replace above mentioned approach by using IDA framework.
While at it, define the instance range to be [0, 4096).
Fixes: e49bd2dd5a50 ("ACPI: use PNPID:instance_no as bus_id of ACPI device")
Fixes: ca9dc8d42b30 ("ACPI / scan: Fix acpi_bus_id_list bookkeeping")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1013ff7a5472db637c56bb6237f8343398c03a7 ]
The upfront allocation of new_bus_id is done to avoid allocating
memory under acpi_device_lock, but it doesn't really help,
because (1) it leads to many unnecessary memory allocations for
_ADR devices, (2) kstrdup_const() is run under that lock anyway and
(3) it complicates the code.
Rearrange acpi_device_add() to allocate memory for a new struct
acpi_device_bus_id instance only when necessary, eliminate a redundant
local variable from it and reduce the number of labels in there.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d669ceb69c276f7637cf760287ca4187add082e ]
Commit 24f6b6036c9e ("dm table: fix zoned iterate_devices based device
capability checks") triggered dm table load failure when dm-zoned device
is set up for zoned block devices and a regular device for cache.
The commit inverted logic of two callback functions for iterate_devices:
device_is_zoned_model() and device_matches_zone_sectors(). The logic of
device_is_zoned_model() was inverted then all destination devices of all
targets in dm table are required to have the expected zoned model. This
is fine for dm-linear, dm-flakey and dm-crypt on zoned block devices
since each target has only one destination device. However, this results
in failure for dm-zoned with regular cache device since that target has
both regular block device and zoned block devices.
As for device_matches_zone_sectors(), the commit inverted the logic to
require all zoned block devices in each target have the specified
zone_sectors. This check also fails for regular block device which does
not have zones.
To avoid the check failures, fix the zone model check and the zone
sectors check. For zone model check, introduce the new feature flag
DM_TARGET_MIXED_ZONED_MODEL, and set it to dm-zoned target. When the
target has this flag, allow it to have destination devices with any
zoned model. For zone sectors check, skip the check if the destination
device is not a zoned block device. Also add comments and improve an
error message to clarify expectations to the two checks.
Fixes: 24f6b6036c9e ("dm table: fix zoned iterate_devices based device capability checks")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1dd9bf688b0dcc5a34dca660de46c7570bd9243 ]
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that.
Fixes: 733336262b28 ("net: phy: Allow BCM5481x PHYs to setup internal TX/RX clock delay")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3afd0218992a8d1398e9791d6c2edd4c948ae7ee ]
The default configuration for the BCM54616S PHY may not match the desired
mode when using 1000BaseX or SGMII interface modes, such as when it is on
an SFP module. Add code to explicitly set the correct mode using
programming sequences provided by Bel-Fuse:
https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-05-series.pdf
https://www.belfuse.com/resources/datasheets/powersolutions/ds-bps-sfp-1gbt-06-series.pdf
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 133bf7b4fbbe58cff5492e37e95e75c88161f1b8 ]
Avoid a forward declaration by moving the callers of
bcm54xx_config_clock_delay() below its body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4217a64e18a1647a0dbc68cb3169a5a06f054ec8 ]
At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.
Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.
This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59cd4f19267a0aab87a8c07e4426eb7187ee548d ]
The driver did not always clean up all allocated resources when probe
failed. Fix the probe cleanup path to clean up everything that was
allocated.
Fixes: 57baf8cc70ea ("net: axienet: Handle deferred probe on clock properly")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a02556086fc0eb16e0a0d09043e9ffb0e31c7db ]
Update the axienet driver to properly support the Xilinx PCS/PMA PHY
component which is used for 1000BaseX and SGMII modes, including
properly configuring the auto-negotiation mode of the PHY and reading
the negotiated state from the PHY.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20201028171429.1699922-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98dfb02aa22280bd8833836d1b00ab0488fa951f ]
Igb needs a similar fix as commit 75aab4e10ae6a ("i40e: avoid
premature Rx buffer reuse")
The page recycle code, incorrectly, relied on that a page fragment
could not be freed inside xdp_do_redirect(). This assumption leads to
that page fragments that are used by the stack/XDP redirect can be
reused and overwritten.
To avoid this, store the page count prior invoking xdp_do_redirect().
Longer explanation:
Intel NICs have a recycle mechanism. The main idea is that a page is
split into two parts. One part is owned by the driver, one part might
be owned by someone else, such as the stack.
t0: Page is allocated, and put on the Rx ring
+---------------
used by NIC ->| upper buffer
(rx_buffer) +---------------
| lower buffer
+---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX
t1: Buffer is received, and passed to the stack (e.g.)
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 1
t2: Buffer is received, and redirected
+---------------
| upper buff (skb)
+---------------
used by NIC ->| lower buffer
(rx_buffer) +---------------
Now, prior calling xdp_do_redirect():
page count == USHRT_MAX
rx_buffer->pagecnt_bias == USHRT_MAX - 2
This means that buffer *cannot* be flipped/reused, because the skb is
still using it.
The problem arises when xdp_do_redirect() actually frees the
segment. Then we get:
page count == USHRT_MAX - 1
rx_buffer->pagecnt_bias == USHRT_MAX - 2
From a recycle perspective, the buffer can be flipped and reused,
which means that the skb data area is passed to the Rx HW ring!
To work around this, the page count is stored prior calling
xdp_do_redirect().
Fixes: 9cbc948b5a20 ("igb: add XDP support")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3408be145a5d6418ff955fe5badde652be90e700 ]
Not setting the ipv6 bit while destroying ipv6 listening servers may
result in potential fatal adapter errors due to lookup engine memory hash
errors. Therefore always set ipv6 field while destroying ipv6 listening
servers.
Fixes: 830662f6f032 ("RDMA/cxgb4: Add support for active and passive open connection with IPv6 address")
Link: https://lore.kernel.org/r/20210324190453.8171-1-bharat@chelsio.com
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b514ec72706a31bea0c3b97e622b81535b5323a ]
The Xen memory hotplug limit should depend on the memory hotplug
generic option, rather than the Xen balloon configuration. It's
|
