| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 655c447c97d7fe462e6cd9e15809037be028bc70 ]
In arm_smmu_gerror_handler(), the value of the SMMU_GERROR register is
filtered by GERROR_ERR_MASK. However, the GERROR_ERR_MASK does not contain
the SFM bit. As a result, the subsequent error processing is not performed
when only the SFM error occurs.
Fixes: 48ec83bcbcf5 ("iommu/arm-smmu: Add initial driver support for ARM SMMUv3 devices")
Reported-by: Rui Zhu <zhurui3@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210324081603.1074-1-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bd85125ea88513f637a62a72e8949c579c5c0a87 ]
A System Error (SError, followed by kernel panic) was detected when
trying to print the supported pins in a pinctrl device which supports
multiple pins per register. This change fixes the pcs_pin_dbg_show() in
pinctrl-single driver when bits_per_mux is not zero. In addition move
offset calculation and pin offset in register to common function.
Fixes: 4e7e8017a80e ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20210319152133.28705-4-hhhawa@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8fa2ea202b13b6da81e26c399ff1d87488398453 ]
Remove unused parameter 'pin_pos' from pcs_add_pin().
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Drew Fustini <drew@beagleboard.org>
Link: https://lore.kernel.org/r/20210319152133.28705-3-hhhawa@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 78a523fe73b81b4447beb2d6c78c9fafae24eebb ]
When supervisor/privilige mode SVM is used, we bind init_mm.pgd with
a supervisor PASID. There should not be any page fault for init_mm.
Execution request with DMA read is also not supported.
This patch checks PRQ descriptor for both unsupported configurations,
reject them both with invalid responses.
Fixes: 1c4f88b7f1f92 ("iommu/vt-d: Shared virtual address in scalable mode")
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Link: https://lore.kernel.org/r/1614680040-1989-4-git-send-email-jacob.jun.pan@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b9abb19fa5fd2d8a4be61c6cd4b2a48aa1a17f9c ]
The device iommu probe/attach might have failed leaving dev->iommu
to NULL and device drivers may still invoke these functions resulting
in a crash in iommu vendor driver code.
Hence make sure we check that.
Fixes: a3a195929d40 ("iommu: Add APIs for multiple domains per device")
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20210303173611.520-1-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5acd0cfbfbb5a688da1bfb1a2152b0c855115a35 ]
There are two "netif_running" checks in this driver. One is in
"lapbeth_xmit" and the other is in "lapbeth_rcv". They serve to make
sure that the LAPB APIs called in these functions are called before
"lapb_unregister" is called by the "ndo_stop" function.
However, these "netif_running" checks are unreliable, because it's
possible that immediately after "netif_running" returns true, "ndo_stop"
is called (which causes "lapb_unregister" to be called).
This patch adds locking to make sure "lapbeth_xmit" and "lapbeth_rcv" can
reliably check and ensure the netif is running while doing their work.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e21b6e5a54628cd3935f200049d4430c25c54e03 ]
Write the value instead of reading it twice.
Fixes: c5c77ba18ea6 ("staging: wilc1000: Add SDIO/SPI 802.11 driver")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210224163706.519658-1-marcus.folkesson@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6fe6e568639859db960c8fcef19a2ece1c2d7eae ]
Correct the map between mlx5 rates and corresponding ib rates, as they
don't always have a fixed offset between them.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Link: https://lore.kernel.org/r/20210304124517.1100608-4-leon@kernel.org
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f567d6ef8606fb427636e824c867229ecb5aefab ]
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
Fixes: 81bb773faed7 ("HID: plantronics: Update to map volume up/down controls")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 72ce11ddfa4e9e1879103581a60b7e34547eaa0a ]
In null_init, null_add_dev(dev) is called.
In null_add_dev, it calls null_free_zoned_dev(dev) to free dev->zones
via kvfree(dev->zones) in out_cleanup_zone branch and returns err.
Then null_init accept the err code and then calls null_free_dev(dev).
But in null_free_dev(dev), dev->zones is freed again by
null_free_zoned_dev().
My patch set dev->zones to NULL in null_free_zoned_dev() after
kvfree(dev->zones) is called, to avoid the double free.
Fixes: 2984c8684f962 ("nullb: factor disk parameters")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Link: https://lore.kernel.org/r/20210426143229.7374-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5c08b0f75575648032f309a6f58294453423ed93 ]
If some of the allocations fail between the dev_set_name() and the
device_register() then the name will not be freed. Fix this by
moving dev_set_name() directly in front of the call to device_register().
Fixes: a2aa24734d9d ("HSI: Add common DT binding for HSI client devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 147d211cc9b4d753148d1640a1758b25edfbf437 ]
Some of the H265 status flags are wrong. Redefine them to corespond to
Allwinner CedarC open source userspace library. Only one of these flags
is actually used and new value also matches value used in libvdpau-sunxi
library, which is proven to be working.
Note that wrong (old) value in right circumstances (in combination with
another H265 decoding bug) causes driver lock up. With this fix decoding
is still broken (green output) but at least driver doesn't lock up.
Fixes: 86caab29da78 ("media: cedrus: Add HEVC/H.265 decoding support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e51183be1fa96dc6d3cd11b3c25a0f595807315e ]
According to the module parameter description for sgl_threshold,
a value of 0 means that SGLs are disabled.
If SGLs are disabled, we should respect that, even for the case
where the request is made up of a single physical segment.
Fixes: 297910571f08 ("nvme-pci: optimize mapping single segment requests using SGLs")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bdaf13279192c60b2b1fc99badef53b494fec055 ]
In case there is an io that contains inline data and it goes to
parsing error flow, command response will free command and iov
before clearing the data on the socket buffer.
This will delay the command response until receive flow is completed.
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Signed-off-by: Elad Grupi <elad.grupi@dell.com>
Signed-off-by: Hou Pu <houpu.main@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4917e498c6894ba077867aff78f82cffd5ffbb5c ]
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220fd ("mfd: Add STM32 Timers driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9468ab84032f96496e998cfa173cd1d0ac316bcd ]
Unisoc mailbox has no way to be enabled/disabled for any single channel.
They can only be set to startup or shutdown as a whole device at same time.
Add a variable to count references to avoid mailbox FIFO being reset
unexpectedly when clients are requesting or freeing channels.
Also add a lock to dismiss possible conflicts from register r/w in
different startup or shutdown threads. And fix the crash problem when early
interrupts come from channel which has not been requested by client yet.
Fixes: ca27fc26cd22 ("mailbox: sprd: Add Spreadtrum mailbox driver")
Signed-off-by: Orson Zhai <orson.zhai@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 15cfef8623a449d40d16541687afd58e78033be3 ]
This fixes an issue hitting the BUG_ON() in ibmvfc_do_work(). When going
through a host action of IBMVFC_HOST_ACTION_RESET, we change the action to
IBMVFC_HOST_ACTION_TGT_DEL, then drop the host lock, and reset the CRQ,
which changes the host state to IBMVFC_NO_CRQ. If, prior to setting the
host state to IBMVFC_NO_CRQ, ibmvfc_init_host() is called, it can then end
up changing the host action to IBMVFC_HOST_ACTION_INIT. If we then change
the host state to IBMVFC_NO_CRQ, we will then hit the BUG_ON().
Make a couple of changes to avoid this. Leave the host action to be
IBMVFC_HOST_ACTION_RESET or IBMVFC_HOST_ACTION_REENABLE until after we drop
the host lock and reset or reenable the CRQ. Also harden the host state
machine to ensure we cannot leave the reset / reenable state until we've
finished processing the reset or reenable.
Link: https://lore.kernel.org/r/20210413001009.902400-1-tyreld@linux.ibm.com
Fixes: 73ee5d867287 ("[SCSI] ibmvfc: Fix soft lockup on resume")
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
[tyreld: added fixes tag]
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mkp: fix comment checkpatch warnings]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1160d61bc51e87e509cfaf9da50a0060f67b6de4 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #s), causing it to fail with -EINVAL (overridden by -ENODEV
further below). Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/8f4b8fa5-8251-b977-70a1-9099bcb4bb17@omprussia.ru
Fixes: c27d85f3f3c5 ("[SCSI] SNI RM 53c710 driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 14b321380eb333c82853d7d612d0995f05f88fdc ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/363eb4c8-a3bf-4dc9-2a9e-90f349030a15@omprussia.ru
Fixes: 0bb67f181834 ("[SCSI] sun3x_esp: convert to esp_scsi")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 38fca15c29db6ed06e894ac194502633e2a7d1fb ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding the real
error code. Stop calling request_irq() with the invalid IRQ #s.
Link: https://lore.kernel.org/r/594aa9ae-2215-49f6-f73c-33bd38989912@omprussia.ru
Fixes: 352e921f0dd4 ("[SCSI] jazz_esp: converted to use esp_core")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6c11dc060427e07ca144eacaccd696106b361b06 ]
Commit df2d8213d9e3 ("hisi_sas: use platform_get_irq()") failed to take
into account that irq_of_parse_and_map() and platform_get_irq() have a
different way of indicating an error: the former returns 0 and the latter
returns a negative error code. Fix up the IRQ checks!
Link: https://lore.kernel.org/r/810f26d3-908b-1d6b-dc5c-40019726baca@omprussia.ru
Fixes: df2d8213d9e3 ("hisi_sas: use platform_get_irq()")
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 339c9b63cc7ce779ce45c675bf709cb58b807fc3 ]
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Propagate the error code
upstream as it should have been done from the start...
Link: https://lore.kernel.org/r/420364ca-614a-45e3-4e35-0e0653c7bc53@omprussia.ru
Fixes: 2953f850c3b8 ("[SCSI] ufs: use devres functions for ufshcd")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 40fa7394a1ad5706e795823276f2e394cca145d0 ]
The for-loop iterates with a u8 loop counter i and compares this with the
loop upper limit of pm8001_ha->max_q_num which is a u32 type. There is a
potential infinite loop if pm8001_ha->max_q_num is larger than the u8 loop
counter. Fix this by making the loop counter the same type as
pm8001_ha->max_q_num.
[mkp: this is purely theoretical, max_q_num is currently limited to 64]
Link: https://lore.kernel.org/r/20210407135840.494747-1-colin.king@canonical.com
Fixes: 65df7d1986a1 ("scsi: pm80xx: Fix chip initialization failure")
Addresses-Coverity: ("Infinite loop")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3f744a14f331f56703a9d74e86520db045f11831 ]
The mpi_uninit_check() takes longer for inbound doorbell register to be
cleared. Increase the timeout substantially so that the driver does not
fail to load.
Previously, the inbound doorbell wait time was mistakenly increased in the
mpi_init_check() instead of mpi_uninit_check(). It is okay to leave the
mpi_init_check() wait time as-is as these are timeout values and if there
is a failure, waiting longer is not an issue.
Link: https://lore.kernel.org/r/20210406180534.1924345-2-ipylypiv@google.com
Fixes: e90e236250e9 ("scsi: pm80xx: Increase timeout for pm80xx mpi_uninit_check")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f6b1340dc751a6caa2a0567b667d0f4f4172cd58 ]
The for-loop iterates with a u8 loop counter i and compares this
with the loop upper limit of num_parents that is an int type.
There is a potential infinite loop if num_parents is larger than
the u8 loop counter. Fix this by making the loop counter the same
type as num_parents. Also make num_parents an unsigned int to
match the return type of the call to clk_hw_get_num_parents.
Addresses-Coverity: ("Infinite loop")
Fixes: 734d82f4a678 ("clk: uniphier: add core support code for UniPhier clock driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210409090104.629722-1-colin.king@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 25315ebfaefcffd126a266116b37bb8a3d1c4620 ]
In radeon_dp_mst_detect(), We should check whether or not @connector
has been unregistered from userspace. If the connector is unregistered,
we should return disconnected status.
Fixes: 9843ead08f18 ("drm/radeon: add DisplayPort MST support (v2)")
Signed-off-by: Yingjie Wang <wangyingjie55@126.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3bb1105071fb974e3e3ca2f92ddfd69c81285ab6 ]
Replace GFP_KERNEL with GFP_ATOMIC as dcn20_resource_construct()
can't sleep.
Partially fixes: https://bugzilla.kernel.org/show_bug.cgi?id=212311
as dcn20_resource_construct() also calls into SMU functions which does
mutex_lock().
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0a859edda46b45baeab9687d173102300d76e2b ]
CONFIG_IPQ_APSS_PLL is tristate option and therefore this driver can
be compiled as a module. This patch adds missing MODULE_DEVICE_TABLE
definition which generates correct modalias for automatic loading of
this driver when it is built as an external module.
Fixes: ecd2bacfbbc4 ("clk: qcom: Add ipq apss pll driver")
Signed-off-by: Chen Hui <clare.chenhui@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409082352.233810-4-clare.chenhui@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 790b516ada10a4dcc0f0a56dc0ced475d86d5820 ]
CONFIG_QCOM_A53PLL is tristate option and therefore this driver can be
compiled as a module. This patch adds missing MODULE_DEVICE_TABLE
definition which generates correct modalias for automatic loading of
this driver when it is built as an external module.
Fixes: 0c6ab1b8f894 ("clk: qcom: Add A53 PLL support")
Signed-off-by: Chen Hui <clare.chenhui@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409082352.233810-3-clare.chenhui@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5842ab76bbfadb37eaea91e53c1efe34ae504e4a ]
The dp->train_set[] for this driver is only two characters, not four so
this memsets too much. Fortunately, this ends up corrupting a struct
hole and not anything important.
Fixes: d76271d22694 ("drm: xlnx: DRM/KMS driver for Xilinx ZynqMP DisplayPort Subsystem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/YGLwCBMotnrKZu6P@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 394cdb69a3c30b33524cf1204afe5cceaba69cdc ]
If there is a IOCTL_SET_PLL_FRAC_MODE request sent to ATF ever,
we shouldn't skip invoking PM_CLOCK_ENABLE fn even though this
pll has been enabled. In ATF implementation, it will only assign
the mode to the variable (struct pm_pll *)pll->mode when handling
IOCTL_SET_PLL_FRAC_MODE call. Invoking PM_CLOCK_ENABLE can force
ATF send request to PWU to set the pll mode to PLL's register.
There is a scenario that happens in enabling VPLL_INT(clk_id:96):
1) VPLL_INT has been enabled during booting.
2) A driver calls clk_set_rate and according to the rate, the VPLL_INT
should be set to FRAC mode. Then zynqmp_pll_set_mode is called
to pass IOCTL_SET_PLL_FRAC_MODE to ATF. Note that at this point
ATF just stores the mode to a variable.
3) This driver calls clk_prepare_enable and zynqmp_pll_enable is
called to try to enable VPLL_INT pll. Because of 1), the function
zynqmp_pll_enable just returns without doing anything after checking
that this pll has been enabled.
In the scenario above, the pll mode of VPLL_INT will never be set
successfully. So adding set_pll_mode to check condition to fix it.
Fixes: 3fde0e16d016 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210406153131.601701-1-quanyang.wang@windriver.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d7fd3f9f53df8bb2212dff70f66f12cae0e1a653 ]
The round_rate callback should only perform rate calculation and not
involve calling zynqmp_pll_set_mode to change the pll mode. So let's
move zynqmp_pll_set_mode out of round_rate and to set_rate callback.
Fixes: 3fde0e16d016 ("drivers: clk: Add ZynqMP clock driver")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210406154015.602779-1-quanyang.wang@windriver.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b5a1f8921d5040bb788492bf33a66758021e4be5 ]
There is a small race where the parent is NULL even though the kobj has
already been made visible in sysfs.
For instance the attribute_group is made visible in sysfs_create_files()
and the mdev_type_attr_show() does:
ret = attr->show(kobj, type->parent->dev, buf);
Which will crash on NULL parent. Move the parent setup to before the type
pointer leaves the stack frame.
Fixes: 7b96953bc640 ("vfio: Mediated device Core driver")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <2-v2-d36939638fc6+d54-vfio2_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4aeec3984ddc853f7c65903bde472ffdef738bae ]
vfio_add_group_dev() must be called only after all of the private data in
vdev is fully setup and ready, otherwise there could be races with user
space instantiating a device file descriptor and starting to call ops.
For instance vfio_pci_reflck_attach() sets vdev->reflck and
vfio_pci_open(), called by fops open, unconditionally derefs it, which
will crash if things get out of order.
Fixes: cc20d7999000 ("vfio/pci: Introduce VF token")
Fixes: e309df5b0c9e ("vfio/pci: Parallelize device open and release")
Fixes: 6eb7018705de ("vfio-pci: Move idle devices to D3hot power state")
Fixes: ecaa1f6a0154 ("vfio-pci: Add VGA arbiter client")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <8-v3-225de1400dfc+4e074-vfio1_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 61e90817482871b614133c0f20feb1aba2faec86 ]
vfio_pci_probe() is quite complicated, with optional VF and VGA sub
components. Move these into clear init/uninit functions and have a linear
flow in probe/remove.
This fixes a few little buglets:
- vfio_pci_remove() is in the wrong order, vga_client_register() removes
a notifier and is after kfree(vdev), but the notifier refers to vdev,
so it can use after free in a race.
- vga_client_register() can fail but was ignored
Organize things so destruction order is the reverse of creation order.
Fixes: ecaa1f6a0154 ("vfio-pci: Add VGA arbiter client")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <7-v3-225de1400dfc+4e074-vfio1_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b1fe162e584a88ec7f12a651a2a50f94dd8cfac ]
vfio_add_group_dev() must be called only after all of the private data in
vdev is fully setup and ready, otherwise there could be races with user
space instantiating a device file descriptor and starting to call ops.
For instance vfio_fsl_mc_reflck_attach() sets vdev->reflck and
vfio_fsl_mc_open(), called by fops open, unconditionally derefs it, which
will crash if things get out of order.
This driver started life with the right sequence, but two commits added
stuff after vfio_add_group_dev().
Fixes: 2e0d29561f59 ("vfio/fsl-mc: Add irq infrastructure for fsl-mc devices")
Fixes: f2ba7e8c947b ("vfio/fsl-mc: Added lock support in preparation for interrupt handling")
Co-developed-by: Diana Craciun OSS <diana.craciun@oss.nxp.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <5-v3-225de1400dfc+4e074-vfio1_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be7e8af98f3af729aa9f08b1053f9533a5cceb91 ]
When a request is re-inited it will release all control handler
objects that are still in the request. It does that by unbinding
and putting all those objects. When the object is unbound the
obj->req pointer is set to NULL, and the object's unbind op is
called. When the object it put the object's release op is called
to free the memory.
For a request object that contains a control handler that means
that v4l2_ctrl_handler_free() is called in the release op.
A control handler used in a request has a pointer to the main
control handler that is created by the driver and contains the
current state of all controls. If the device is unbound (due to
rmmod or a forced unbind), then that main handler is freed, again
by calling v4l2_ctrl_handler_free(), and any outstanding request
objects that refer to that main handler have to be unbound and put
as well.
It does that by this test:
if (!hdl->req_obj.req && !list_empty(&hdl->requests)) {
I.e. the handler has no pointer to a request, so is the main
handler, and one or more request objects refer to this main
handler.
However, this test is wrong since hdl->req_obj.req is actually
NULL when re-initing a request (the object unbind will set req to
NULL), and the only reason this seemingly worked is that the
requests list is typically empty since the request's unbind op
will remove the handler from the requests list.
But if another thread is at the same time adding a new control
to a request, then there is a race condition where one thread
is removing a control handler object from the requests list and
another thread is adding one. The result is that hdl->requests
is no longer empty and the code thinks that a main handler is
being freed instead of a control handler that is part of a request.
There are two bugs here: first the test for hdl->req_obj.req: this
should be hdl->req_obj.ops since only the main control handler will
have a NULL pointer there.
The second is that adding or deleting request objects from the
requests list of the main handler isn't protected by taking the
main handler's lock.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: John Cox <jc@kynesim.co.uk>
Fixes: 6fa6f831f095 ("media: v4l2-ctrls: add core request support")
Tested-by: John Cox <jc@kynesim.co.uk>
Reported-by: John Cox <jc@kynesim.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd90caa0111e178b52b21e56364bc2244a3973b3 ]
Move incrementing/decrementing runtime PM count to
imx219_start_streaming()/imx219_stop_streaming() functions respectively.
This fixes an issue of unbalanced runtime PM count in resume callback
error path where streaming is stopped and runtime PM count is left
unbalanced.
Fixes: 1283b3b8f82b9 ("media: i2c: Add driver for Sony IMX219 sensor")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
from imx219_set_stream
[ Upstream commit 745d4612d2c853c00abadbf69799c8aee7f99c39 ]
Move out locking/unlocking of vflip and hflip controls from
imx219_set_stream() to the imx219_start_streaming()/
imx219_stop_streaming() respectively.
This fixes an issue in resume callback error path where streaming is
stopped and the controls are left in locked state.
Fixes: 1283b3b8f82b9 ("media: i2c: Add driver for Sony IMX219 sensor")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd8f7fa908f66dd44abcd83cbb50410524b9f8ef ]
If ANA is enabled but no ANA group descriptor is found when creating
a new namespace the ANA log is most likely out of date, so trigger
a re-read. The namespace will be tagged with the NS_ANA_PENDING flag
to exclude it from path selection until the ANA log has been re-read.
Fixes: 32acab3181c7 ("nvme: implement multipath access to nvme subsystems")
Reported-by: Martin George <marting@netapp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 04722cec1436c732d39153ce6ae2ebf71ac3ade7 ]
Currently POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT and
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE are exposed on
the battery node and this is incorrect.
This patch exposes both of them on the charger node rather
than the battery node.
Fixes: 5069185fc18e ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 379c9a24cc239000b1dec53db02fe17a86947423 ]
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b5332a9f3f3d884a1b646ce155e664cc558c1722 ]
We are not changing anything in the TCP connection state so
we should not take a write_lock but rather a read lock.
This caused a deadlock when running nvmet-tcp and nvme-tcp
on the same system, where state_change callbacks on the
host and on the controller side have causal relationship
and made lockdep report on this with blktests:
================================
WARNING: inconsistent lock state
5.12.0-rc3 #1 Tainted: G I
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-R} usage.
nvme/1324 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff888363151000 (clock-AF_INET){++-?}-{2:2}, at: nvme_tcp_state_change+0x21/0x150 [nvme_tcp]
{IN-SOFTIRQ-W} state was registered at:
__lock_acquire+0x79b/0x18d0
lock_acquire+0x1ca/0x480
_raw_write_lock_bh+0x39/0x80
nvmet_tcp_state_change+0x21/0x170 [nvmet_tcp]
tcp_fin+0x2a8/0x780
tcp_data_queue+0xf94/0x1f20
tcp_rcv_established+0x6ba/0x1f00
tcp_v4_do_rcv+0x502/0x760
tcp_v4_rcv+0x257e/0x3430
ip_protocol_deliver_rcu+0x69/0x6a0
ip_local_deliver_finish+0x1e2/0x2f0
ip_local_deliver+0x1a2/0x420
ip_rcv+0x4fb/0x6b0
__netif_receive_skb_one_core+0x162/0x1b0
process_backlog+0x1ff/0x770
__napi_poll.constprop.0+0xa9/0x5c0
net_rx_action+0x7b3/0xb30
__do_softirq+0x1f0/0x940
do_softirq+0xa1/0xd0
__local_bh_enable_ip+0xd8/0x100
ip_finish_output2+0x6b7/0x18a0
__ip_queue_xmit+0x706/0x1aa0
__tcp_transmit_skb+0x2068/0x2e20
tcp_write_xmit+0xc9e/0x2bb0
__tcp_push_pending_frames+0x92/0x310
inet_shutdown+0x158/0x300
__nvme_tcp_stop_queue+0x36/0x270 [nvme_tcp]
nvme_tcp_stop_queue+0x87/0xb0 [nvme_tcp]
nvme_tcp_teardown_admin_queue+0x69/0xe0 [nvme_tcp]
nvme_do_delete_ctrl+0x100/0x10c [nvme_core]
nvme_sysfs_delete.cold+0x8/0xd [nvme_core]
kernfs_fop_write_iter+0x2c7/0x460
new_sync_write+0x36c/0x610
vfs_write+0x5c0/0x870
ksys_write+0xf9/0x1d0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
irq event stamp: 10687
hardirqs last enabled at (10687): [<ffffffff9ec376bd>] _raw_spin_unlock_irqrestore+0x2d/0x40
hardirqs last disabled at (10686): [<ffffffff9ec374d8>] _raw_spin_lock_irqsave+0x68/0x90
softirqs last enabled at (10684): [<ffffffff9f000608>] __do_softirq+0x608/0x940
softirqs last disabled at (10649): [<ffffffff9cdedd31>] do_softirq+0xa1/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(clock-AF_INET);
<Interrupt>
lock(clock-AF_INET);
*** DEADLOCK ***
5 locks held by nvme/1324:
#0: ffff8884a01fe470 (sb_writers#4){.+.+}-{0:0}, at: ksys_write+0xf9/0x1d0
#1: ffff8886e435c090 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x216/0x460
#2: ffff888104d90c38 (kn->active#255){++++}-{0:0}, at: kernfs_remove_self+0x22d/0x330
#3: ffff8884634538d0 (&queue->queue_lock){+.+.}-{3:3}, at: nvme_tcp_stop_queue+0x52/0xb0 [nvme_tcp]
#4: ffff888363150d30 (sk_lock-AF_INET){+.+.}-{0:0}, at: inet_shutdown+0x59/0x300
stack backtrace:
CPU: 26 PID: 1324 Comm: nvme Tainted: G I 5.12.0-rc3 #1
Hardware name: Dell Inc. PowerEdge R640/06NR82, BIOS 2.10.0 11/12/2020
Call Trace:
dump_stack+0x93/0xc2
mark_lock_irq.cold+0x2c/0xb3
? verify_lock_unused+0x390/0x390
? stack_trace_consume_entry+0x160/0x160
? lock_downgrade+0x100/0x100
? save_trace+0x88/0x5e0
? _raw_spin_unlock_irqrestore+0x2d/0x40
mark_lock+0x530/0x1470
? mark_lock_irq+0x1d10/0x1d10
? enqueue_timer+0x660/0x660
mark_usage+0x215/0x2a0
__lock_acquire+0x79b/0x18d0
? tcp_schedule_loss_probe.part.0+0x38c/0x520
lock_acquire+0x1ca/0x480
? nvme_tcp_state_change+0x21/0x150 [nvme_tcp]
? rcu_read_unlock+0x40/0x40
? tcp_mtu_probe+0x1ae0/0x1ae0
? kmalloc_reserve+0xa0/0xa0
? sysfs_file_ops+0x170/0x170
_raw_read_lock+0x3d/0xa0
? nvme_tcp_state_change+0x21/0x150 [nvme_tcp]
nvme_tcp_state_change+0x21/0x150 [nvme_tcp]
? sysfs_file_ops+0x170/0x170
inet_shutdown+0x189/0x300
__nvme_tcp_stop_queue+0x36/0x270 [nvme_tcp]
nvme_tcp_stop_queue+0x87/0xb0 [nvme_tcp]
nvme_tcp_teardown_admin_queue+0x69/0xe0 [nvme_tcp]
nvme_do_delete_ctrl+0x100/0x10c [nvme_core]
nvme_sysfs_delete.cold+0x8/0xd [nvme_core]
kernfs_fop_write_iter+0x2c7/0x460
new_sync_write+0x36c/0x610
? new_sync_read+0x600/0x600
? lock_acquire+0x1ca/0x480
? rcu_read_unlock+0x40/0x40
? lock_is_held_type+0x9a/0x110
vfs_write+0x5c0/0x870
ksys_write+0xf9/0x1d0
? __ia32_sys_read+0xa0/0xa0
? lockdep_hardirqs_on_prepare.part.0+0x198/0x340
? syscall_enter_from_user_mode+0x27/0x70
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8b73b45d54a14588f86792869bfb23098ea254cb ]
The TCP stack can run from process context for a long time
so we should disable BH here.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b30d0040f06159de97ad9c0b1536f47250719d7d ]
Iff platform_get_irq() returns 0, ahci_platform_init_host() would return 0
early (as if the call was successful). Override IRQ0 with -EINVAL instead
as the 'libata' reg |
