| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This should resolve the merge/build issues reported when trying to
create linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into master
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.8-rc7
They include:
- habanalabs fixes
- tiny fpga driver fixes
- /dev/mem fixup from previous changes
- interconnect driver fixes
- binder fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
interconnect: msm8916: Fix buswidth of pcnoc_s nodes
interconnect: Do not skip aggregation for disabled paths
/dev/mem: Add missing memory barriers for devmem_inode
binder: Don't use mmput() from shrinker function.
habanalabs: prevent possible out-of-bounds array access
fpga: dfl: fix bug in port reset handshake
fpga: dfl: pci: reduce the scope of variable 'ret'
habanalabs: set 4s timeout for message to device CPU
habanalabs: set clock gating per engine
habanalabs: block WREG_BULK packet on PDMA
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into master
Pull driver core fix from Greg KH:
"A single driver core fix for 5.8-rc7. It resolves a problem found in
the previous fix for this code made in 5.8-rc6. Hopefully this is all
now cleared up, as this seems to be the last of the reported issues in
this area, and was tested on the problem hardware.
This patch has been in linux-next with no reported problems"
* tag 'driver-core-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
device property: Avoid NULL pointer dereference in device_get_next_child_node()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into master
Pull staging driver fixes from Greg KH:
"Five small staging driver fixes for 5.8-rc7 to resolve some reported
problems:
- four comedi driver fixes for problems found with them
- a syzbot-found fix for the wlang-ng driver that resolves a much
reported problem.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: wlan-ng: properly check endpoint types
staging: comedi: addi_apci_1564: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: addi_apci_1500: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: addi_apci_1032: check INSN_CONFIG_DIGITAL_TRIG shift
staging: comedi: ni_6527: fix INSN_CONFIG_DIGITAL_TRIG support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty and serial and fbcon fixes for 5.8-rc7 to
resolve some reported issues.
The fbcon fix is in here as it was simpler to take it this way (and it
was acked by the maintainer) as it was related to the vt console fix
as well, both of which resolve syzbot-found issues in the console
handling code.
The other serial driver fixes are for small issues reported in the -rc
releases.
All of these have been in linux-next with no reported issues"
* tag 'tty-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: exar: Fix GPIO configuration for Sealevel cards based on XR17V35X
fbdev: Detect integer underflow at "struct fbcon_ops"->clear_margins.
serial: 8250_mtk: Fix high-speed baud rates clamping
serial: 8250: fix null-ptr-deref in serial8250_start_tx()
serial: tegra: drop bogus NULL tty-port checks
serial: tegra: fix CREAD handling for PIO
tty: xilinx_uartps: Really fix id assignment
vt: Reject zero-sized screen buffer size.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into master
Pull USB fixes from Greg KH:
"Three small USB XHCI driver fixes for 5.8-rc7.
They all resolve some minor issues that have been reported on some
different platforms.
All of these have been in linux-next with no reported issues"
* tag 'usb-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: tegra: Fix allocation for the FPCI context
usb: xhci: Fix ASM2142/ASM3142 DMA addressing
usb: xhci-mtk: fix the failure of bandwidth allocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi into master
Pull SCSI fix from James Bottomley:
"Small core patch to fix a corner case bug: we forgot to run the queues
to handle starvation in the error exit from the scsi_queue_rq routine,
which can lead to hangs on error conditions"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Run queue in case of I/O resource contention failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull timer fix from Ingo Molnar:
"Fix a suspend/resume regression (crash) on TI AM3/AM4 SoC's"
* tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull EFI fixes from Ingo Molnar:
"Various EFI fixes:
- Fix the layering violation in the use of the EFI runtime services
availability mask in users of the 'efivars' abstraction
- Revert build fix for GCC v4.8 which is no longer supported
- Clean up some x86 EFI stub details, some of which are borderline
bugs that copy around garbage into padding fields - let's fix these
out of caution.
- Fix build issues while working on RISC-V support
- Avoid --whole-archive when linking the stub on arm64"
* tag 'efi-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Revert "efi/x86: Fix build with gcc 4"
efi/efivars: Expose RT service availability via efivars abstraction
efi/libstub: Move the function prototypes to header file
efi/libstub: Fix gcc error around __umoddi3 for 32 bit builds
efi/libstub/arm64: link stub lib.a conditionally
efi/x86: Only copy upto the end of setup_header
efi/x86: Remove unused variables
|
|
Pull networking fixes from David Miller:
1) Fix RCU locaking in iwlwifi, from Johannes Berg.
2) mt76 can access uninitialized NAPI struct, from Felix Fietkau.
3) Fix race in updating pause settings in bnxt_en, from Vasundhara
Volam.
4) Propagate error return properly during unbind failures in ax88172a,
from George Kennedy.
5) Fix memleak in adf7242_probe, from Liu Jian.
6) smc_drv_probe() can leak, from Wang Hai.
7) Don't muck with the carrier state if register_netdevice() fails in
the bonding driver, from Taehee Yoo.
8) Fix memleak in dpaa_eth_probe, from Liu Jian.
9) Need to check skb_put_padto() return value in hsr_fill_tag(), from
Murali Karicheri.
10) Don't lose ionic RSS hash settings across FW update, from Shannon
Nelson.
11) Fix clobbered SKB control block in act_ct, from Wen Xu.
12) Missing newlink in "tx_timeout" sysfs output, from Xiongfeng Wang.
13) IS_UDPLITE cleanup a long time ago, incorrectly handled
transformations involving UDPLITE_RECV_CC. From Miaohe Lin.
14) Unbalanced locking in netdevsim, from Taehee Yoo.
15) Suppress false-positive error messages in qed driver, from Alexander
Lobakin.
16) Out of bounds read in ax25_connect and ax25_sendmsg, from Peilin Ye.
17) Missing SKB release in cxgb4's uld_send(), from Navid Emamdoost.
18) Uninitialized value in geneve_changelink(), from Cong Wang.
19) Fix deadlock in xen-netfront, from Andera Righi.
19) flush_backlog() frees skbs with IRQs disabled, so should use
dev_kfree_skb_irq() instead of kfree_skb(). From Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
drivers/net/wan: lapb: Corrected the usage of skb_cow
dev: Defer free of skbs in flush_backlog
qrtr: orphan socket in qrtr_release()
xen-netfront: fix potential deadlock in xennet_remove()
flow_offload: Move rhashtable inclusion to the source file
geneve: fix an uninitialized value in geneve_changelink()
bonding: check return value of register_netdevice() in bond_newlink()
tcp: allow at most one TLP probe per flight
AX.25: Prevent integer overflows in connect and sendmsg
cxgb4: add missing release on skb in uld_send()
net: atlantic: fix PTP on AQC10X
AX.25: Prevent out-of-bounds read in ax25_sendmsg()
sctp: shrink stream outq when fails to do addstream reconf
sctp: shrink stream outq only when new outcnt < old outcnt
AX.25: Fix out-of-bounds read in ax25_connect()
enetc: Remove the mdio bus on PF probe bailout
net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offload
net: ethernet: ave: Fix error returns in ave_init
drivers/net/wan/x25_asy: Fix to make it work
ipvs: fix the connection sync failed in some cases
...
|
|
This patch fixed 2 issues with the usage of skb_cow in LAPB drivers
"lapbether" and "hdlc_x25":
1) After skb_cow fails, kfree_skb should be called to drop a reference
to the skb. But in both drivers, kfree_skb is not called.
2) skb_cow should be called before skb_push so that is can ensure the
safety of skb_push. But in "lapbether", it is incorrectly called after
skb_push.
More details about these 2 issues:
1) The behavior of calling kfree_skb on failure is also the behavior of
netif_rx, which is called by this function with "return netif_rx(skb);".
So this function should follow this behavior, too.
2) In "lapbether", skb_cow is called after skb_push. This results in 2
logical issues:
a) skb_push is not protected by skb_cow;
b) An extra headroom of 1 byte is ensured after skb_push. This extra
headroom has no use in this function. It also has no use in the
upper-layer function that this function passes the skb to
(x25_lapb_receive_frame in net/x25/x25_dev.c).
So logically skb_cow should instead be called before skb_push.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into master
Pull PCI fixes from Bjorn Helgaas:
- Reject invalid IRQ 0 command line argument for virtio_mmio because
IRQ 0 now generates warnings (Bjorn Helgaas)
- Revert "PCI/PM: Assume ports without DLL Link Active train links in
100 ms", which broke nouveau (Bjorn Helgaas)
* tag 'pci-v5.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms"
virtio-mmio: Reject invalid IRQ 0 command line argument
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.8
Second set of fixes for v5.8, and hopefully also the last. Three
important regressions fixed.
ath9k
* fix a regression which broke support for all ath9k usb devices
ath10k
* fix a regression which broke support for all QCA4019 AHB devices
iwlwifi
* fix a regression which broke support for some Killer Wireless-AC 1550 cards
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's a potential race in xennet_remove(); this is what the driver is
doing upon unregistering a network device:
1. state = read bus state
2. if state is not "Closed":
3. request to set state to "Closing"
4. wait for state to be set to "Closing"
5. request to set state to "Closed"
6. wait for state to be set to "Closed"
If the state changes to "Closed" immediately after step 1 we are stuck
forever in step 4, because the state will never go back from "Closed" to
"Closing".
Make sure to check also for state == "Closed" in step 4 to prevent the
deadlock.
Also add a 5 sec timeout any time we wait for the bus state to change,
to avoid getting stuck forever in wait_event().
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu into master
Pull iommu fix from Joerg Roedel:
"Fix a NULL-ptr dereference in the QCOM IOMMU driver"
* tag 'iommu-fix-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/qcom: Use domain rather than dev as tlb cookie
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma into master
Pull rdma fixes from Jason Gunthorpe:
"One merge window regression, some corruption bugs in HNS and a few
more syzkaller fixes:
- Two long standing syzkaller races
- Fix incorrect HW configuration in HNS
- Restore accidentally dropped locking in IB CM
- Fix ODP prefetch bug added in the big rework several versions ago"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Prevent prefetch from racing with implicit destruction
RDMA/cm: Protect access to remote_sidr_table
RDMA/core: Fix race in rdma_alloc_commit_uobject()
RDMA/hns: Fix wrong PBL offset when VA is not aligned to PAGE_SIZE
RDMA/hns: Fix wrong assignment of lp_pktn_ini in QPC
RDMA/mlx5: Use xa_lock_irq when access to SRQ table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm into master
Pull device mapper fix from Mike Snitzer:
"A stable fix for DM integrity target's integrity recalculation that
gets skipped when resuming a device. This is a fix for a previous
stable@ fix"
* tag 'for-5.8/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm integrity: fix integrity recalculation that is improperly skipped
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into master
Pull i2c fixes from Wolfram Sang:
"Again some driver bugfixes and some documentation fixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-qcom-geni: Fix DMA transfer race
i2c: rcar: always clear ICSAR to avoid side effects
MAINTAINERS: i2c: at91: handover maintenance to Codrin Ciubotariu
i2c: drop duplicated word in the header file
i2c: cadence: Clear HOLD bit at correct time in Rx path
Revert "i2c: cadence: Fix the hold bit setting"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc into master
Pull MMC fix from Ulf Hansson:
"Fix clock divider calculation in the ASPEED SDHCI controller"
* tag 'mmc-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-aspeed: Fix clock divider calculation
|
|
into master
Pull drm fixes from Dave Airlie:
"Quiet fixes, I may have a single regression fix follow up to this for
nouveau, but it might be next week, Ben was testing it a bit more .
Otherwise two amdgpu fixes, one lima and one sun4i:
amdgpu:
- Fix crash when overclocking VegaM
- Fix possible crash when editing dpm levels
sun4i:
- Fix inverted HPD result; fixes an earlier fix
lima:
- fix timeout during reset"
* tag 'drm-fixes-2020-07-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: Fix NULL dereference in dpm sysfs handlers
drm/amd/powerplay: fix a crash when overclocking Vega M
drm/lima: fix wait pp reset timeout
drm: sun4i: hdmi: Fix inverted HPD result
|
|
git://people.freedesktop.org/~gabbayo/linux into char-misc-next
Oded writes:
This tag contains the following changes for kernel 5.9-rc1:
- Remove rate limiters from GAUDI configuration (no longer needed).
- Set maximum amount of in-flight CS per ASIC type and increase
the maximum amount for GAUDI.
- Refactor signal/wait command submissions code
- Calculate trace frequency from PLLs to show accurate profiling data
- Rephrase error messages to make them more clear to the common user
- Add statistics of dropped CS (counter per possible reason for drop)
- Get ECC information from firmware
- Remove support for partial SoC reset in Gaudi
- Halt device CPU only when reset is certain to happen. Sometimes we abort
the reset procedure and in that case we can't leave device CPU in halt
mode.
- set each CQ to its own work queue to prevent a race between completions
on different CQs.
- Use queue pi/ci in order to determine queue occupancy. This is done to
make the code reusable between current and future ASICs.
- Add more validations for user inputs.
- Refactor PCIe controller configuration to make the code reusable between
current and future ASICs.
- Update firmware interface headers to latest version
- Move all common code to a dedicated common sub-folder
* tag 'misc-habanalabs-next-2020-07-24' of git://people.freedesktop.org/~gabbayo/linux: (28 commits)
habanalabs: Fix memory leak in error flow of context initialization
habanalabs: use no flags on MMU cache invalidation
habanalabs: enable device before hw_init()
habanalabs: create internal CB pool
habanalabs: update hl_boot_if.h from firmware
habanalabs: create common folder
habanalabs: check for DMA errors when clearing memory
habanalabs: verify queue can contain all cs jobs
habanalabs: Assign each CQ with its own work queue
habanalabs: halt device CPU only upon certain reset
habanalabs: remove unused hash
habanalabs: use queue pi/ci in order to determine queue occupancy
habanalabs: configure maximum queues per asic
habanalabs: remove soft-reset support from GAUDI
habanalabs: PCIe iATU refactoring
habanalabs: Extract ECC information from FW
habanalabs: Add dropped cs statistics info struct
habanalabs: extract cpu boot status lookup
habanalabs: rephrase error messages
habanalabs: Increase queues depth
...
|
|
Add a missing free of the cs_pending array in the error flow of context
initialization.
Fixes: c16d45f42b64 ("habanalabs: Use pending CS amount per ASIC")
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
gaudi_mmu_invalidate_cache() doesn't use the flags parameter, and thus
it can be set to 0 when the function is called in the gaudi only files.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Device is now enabled before the hw_init() because part of the
initialization requires communication with the device firmware to get
information that is required for the initialization itself
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
Create a device MMU-mapped internal command buffer pool, in order to allow
the driver to allocate CBs for the signal/wait operations
that are fetched by the queues when they are configured with the user's
address space ID.
We must pre-map this internal pool due to performance issues.
This pool is needed for future ASIC support and it is currently unused in
GOYA and GAUDI.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Update the boot interface file from the latest version from firmware.
Defines for secure boot were added.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
|
|
For internal needs of our CI we need to move all the common code into a
common folder instead of putting them in the root folder of the driver.
Same applies to the common header files under include/
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
|
|
In GAUDI we use QMAN0 DMA for clearing the MMU memory region
at initialization. if this operation fails it places the DMA in an error
state and then when trying to initialize QMAN0 we fail and erroneously
assume its the QMAN that failed.
This commit adds a check and clear of such DMA errors at initialization so
we will have a better understanding of what went wrong.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
In order for the user to be aware of wrong inputs, we must return
error in case the amount of jobs per cs exceeds the corresponding
queue size.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
We identified a possible race during job completion when working
with a single multi-threaded work queue. In order to overcome this
race we suggest using a single threaded work queue per completion
queue, hence we guarantee jobs completion in order.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Currently the driver halts the device CPU in the halt engines function,
which halts all the engines of the ASIC. The problem is that if later on we
stop the reset process (due to inability to clean memory mappings in time),
the CPU will remain in halt mode. This creates many issues, such as
thermal/power control and FLR handling.
Therefore, move the halting of the device CPU to the very end of the reset
process, just before writing to the registers to initiate the reset. In
addition, the driver now needs to send a message to the device F/W to
disable it from sending interrupts to the host machine because during halt
engines function the driver disables the MSI/MSI-X interrupts.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
Remove an old hash that is not in use anymore.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Instead of using the free slots amount on the compute CQ to determine
whether we can submit work to queues, use the queues pi/ci.
This is needed in future ASICs where we don't have CQ per queue.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Currently the amount of maximum queues is statically configured.
Using a static value is causing redundunt cycles when traversing
all queues and consumes more memory than actually needed.
In this patch we configure each asic with the exact number of
queues needed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Soft-reset isn't supported in GAUDI. Remove the code that performs it and
print error in case the user wants to do it via sysfs.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
Divide iATU initialization into inbound/outbound methods.
We must separate it in order to enable different match mode
per PCIe region.
In addition, added support for PCI address match mode.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
ECC (Error Correcting Code) interrupts are going to be handled
by the FW. Hence, we define an interface in which the driver can
obtain the relevant ECC information.
This information is needed for monitoring and can also lead
to a hard reset if ECC error is not correctable.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Add command submission statistics structure which can be obtained
through the info ioctl. Each drop counter describes the reason for
which the command submission was dropped.
This information is needed for the user to be aware of the specific
reason for which the submitted work was dropped. The user can then
utilize the driver more efficiently.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Extract detection of the cpu boot status to a function
to allow code reuse
Signed-off-by: Christine Gharzuzi <cgharzuzi@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
rephrase some error/warning/notice messages to make them more accessible to
ordinary users.
There is no need to print context ASID as the driver currently doesn't
support multiple contexts.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
|
|
After recent concurrent cs amount increase, we must also
increase queues depth since much more concurrent work can be done.
All external queue depths were increased to 4096 as gaudi's
internal queue depths were also increased to 1024.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Rephrase F/W error message to make it more understandable to ordinary
users.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
The profiler needs to know the PLL values for correctly showing the
profiling data. Because our firmware can use different PLL configurations,
we need to read the PLL values from the ASIC to pass them to the profiler.
Signed-off-by: Adam Aharon <aaharon@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Once there is a 64-bit field in a structure, GCC compiler for ARM aligns
the structure to 8 bytes. In order to avoid confusion when these
structures are being passed between CPUs from different architectures, we
explicitly align the structure to 8 bytes.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Use proper bitfield masks instead of shifting values when configuring
packets sent to device.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Currently sync stream is limited only for external queues. We want to
remove this constraint by adding a new queue property dedicated for sync
stream. In addition we move the initialization and reset methods to the
common code since we can re-use them with slight changes.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
Training schemes requires much more concurrent command submissions than
inference does. In addition, training command submissions can be completed
in a non serialized manner. Hence, we add support in which each ASIC will
be able to configure the amount of concurrent pending command submissions,
rather than use a predefined amount. This change will enhance performance
by allowing the user to add more concurrent work without waiting for the
previous work to be completed.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
We no longer need to initialize the rate limiters in GAUDI A1.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
|
|
into char-misc-next
Georgi writes:
interconnect changes for 5.9
Here are the interconnect changes for the 5.9-rc1 merge window
consisting mostly of changes that give the core more flexibility
in order to support some new provider drivers.
Core changes:
- Export of_icc_get_from_provider()
- Relax requirement in of_icc_get_from_provider()
- Allow inter-provider pairs to be configured
- Mark all dummy functions as static inline
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.9-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: Mark all dummy functions as static inline
interconnect: Allow inter-provider pairs to be configured
interconnect: Relax requirement in of_icc_get_from_provider()
interconnect: Export of_icc_get_from_provider()
|
|
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
