| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 77e89afc25f30abd56e76a809ee2884d7c1b63ce upstream.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 826da771291fc25a428e871f9e7fb465e390f852 upstream.
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b69dd5b3780a7298bd893816a09da751bc0636f7 ]
Some arches support cmpxchg() on 4-byte and 8-byte only.
Increase mr_ifc_count width to 32bit to fix this problem.
Fixes: 4a2b285e7e10 ("net: igmp: fix data-race in igmp_ifc_timer_expire()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210811195715.3684218-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 376e4199e327a5cf29b8ec8fb0f64f3d8b429819 ]
Currently TEE_SHM_DMA_BUF flag has been inappropriately used to not
register shared memory allocated for private usage by underlying TEE
driver: OP-TEE in this case. So rather add a new flag as TEE_SHM_PRIV
that can be utilized by underlying TEE drivers for private allocation
and usage of shared memory.
With this corrected, allow tee_shm_alloc_kernel_buf() to allocate a
shared memory region without the backing of dma-buf.
Cc: stable@vger.kernel.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Co-developed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit dc7019b7d0e188d4093b34bd0747ed0d668c63bf upstream.
Adds a new function tee_shm_alloc_kernel_buf() to allocate shared memory
from a kernel driver. This function can later be made more lightweight
by unnecessary dma-buf export.
Cc: stable@vger.kernel.org
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bf88fef0b6f1488abeca594d377991171c00e52a upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6549c46af8551b346bcc0b9043f93848319acd5c ]
For linear regulators, the n_voltages should be (max - min) / step + 1.
Buck voltage from 1v to 3V, per step 100mV, and vout mask is 0x1f.
If value is from 20 to 31, the voltage will all be fixed to 3V.
And LDO also, just vout range is different from 1.2v to 3v, step is the
same. If value is from 18 to 31, the voltage will also be fixed to 3v.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20210627080418.1718127-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1e7107c5ef44431bc1ebbd4c353f1d7c22e5f2ec upstream.
Richard reported sporadic (roughly one in 10 or so) null dereferences and
other strange behaviour for a set of automated LTP tests. Things like:
BUG: kernel NULL pointer dereference, address: 0000000000000008
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 0 PID: 1516 Comm: umount Not tainted 5.10.0-yocto-standard #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-48-gd9c812dda519-prebuilt.qemu.org 04/01/2014
RIP: 0010:kernfs_sop_show_path+0x1b/0x60
...or these others:
RIP: 0010:do_mkdirat+0x6a/0xf0
RIP: 0010:d_alloc_parallel+0x98/0x510
RIP: 0010:do_readlinkat+0x86/0x120
There were other less common instances of some kind of a general scribble
but the common theme was mount and cgroup and a dubious dentry triggering
the NULL dereference. I was only able to reproduce it under qemu by
replicating Richard's setup as closely as possible - I never did get it
to happen on bare metal, even while keeping everything else the same.
In commit 71d883c37e8d ("cgroup_do_mount(): massage calling conventions")
we see this as a part of the overall change:
--------------
struct cgroup_subsys *ss;
- struct dentry *dentry;
[...]
- dentry = cgroup_do_mount(&cgroup_fs_type, fc->sb_flags, root,
- CGROUP_SUPER_MAGIC, ns);
[...]
- if (percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
- struct super_block *sb = dentry->d_sb;
- dput(dentry);
+ ret = cgroup_do_mount(fc, CGROUP_SUPER_MAGIC, ns);
+ if (!ret && percpu_ref_is_dying(&root->cgrp.self.refcnt)) {
+ struct super_block *sb = fc->root->d_sb;
+ dput(fc->root);
deactivate_locked_super(sb);
msleep(10);
return restart_syscall();
}
--------------
In changing from the local "*dentry" variable to using fc->root, we now
export/leave that dentry pointer in the file context after doing the dput()
in the unlikely "is_dying" case. With LTP doing a crazy amount of back to
back mount/unmount [testcases/bin/cgroup_regression_5_1.sh] the unlikely
becomes slightly likely and then bad things happen.
A fix would be to not leave the stale reference in fc->root as follows:
--------------
dput(fc->root);
+ fc->root = NULL;
deactivate_locked_super(sb);
--------------
...but then we are just open-coding a duplicate of fc_drop_locked() so we
simply use that instead.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Zefan Li <lizefan.x@bytedance.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org # v5.1+
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Fixes: 71d883c37e8d ("cgroup_do_mount(): massage calling conventions")
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2beb4a53fc3f1081cedc1c1a198c7f56cc4fc60c ]
The kernel pushes context on to the userspace stack to prepare for the
user's signal handler. When the user has supplied an alternate signal
stack, via sigaltstack(2), it is easy for the kernel to verify that the
stack size is sufficient for the current hardware context.
Check if writing the hardware context to the alternate stack will exceed
it's size. If yes, then instead of corrupting user-data and proceeding with
the original signal handler, an immediate SIGSEGV signal is delivered.
Refactor the stack pointer check code from on_sig_stack() and use the new
helper.
While the kernel allows new source code to discover and use a sufficient
alternate signal stack size, this check is still necessary to protect
binaries with insufficient alternate signal stack size from data
corruption.
Fixes: c2bc11f10a39 ("x86, AVX-512: Enable AVX-512 States Context Switch")
Reported-by: Florian Weimer <fweimer@redhat.com>
Suggested-by: Jann Horn <jannh@google.com>
Suggested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Len Brown <len.brown@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20210518200320.17239-6-chang.seok.bae@intel.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=153531
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e97bc66377bca097e1f3349ca18ca17f202ff659 ]
If a file has already been closed, then it should not be selected to
support further I/O.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
[Trond: Fix an invalid pointer deref reported by Colin Ian King]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 11c7aa0ddea8611007768d3e6b58d45dc60a19e1 upstream.
Commit 545fbd0775ba ("rq-qos: fix missed wake-ups in rq_qos_throttle")
tried to fix a problem that a process could be sleeping in rq_qos_wait()
without anyone to wake it up. However the fix is not complete and the
following can still happen:
CPU1 (waiter1) CPU2 (waiter2) CPU3 (waker)
rq_qos_wait() rq_qos_wait()
acquire_inflight_cb() -> fails
acquire_inflight_cb() -> fails
completes IOs, inflight
decreased
prepare_to_wait_exclusive()
prepare_to_wait_exclusive()
has_sleeper = !wq_has_single_sleeper() -> true as there are two sleepers
has_sleeper = !wq_has_single_sleeper() -> true
io_schedule() io_schedule()
Deadlock as now there's nobody to wakeup the two waiters. The logic
automatically blocking when there are already sleepers is really subtle
and the only way to make it work reliably is that we check whether there
are some waiters in the queue when adding ourselves there. That way, we
are guaranteed that at least the first process to enter the wait queue
will recheck the waiting condition before going to sleep and thus
guarantee forward progress.
Fixes: 545fbd0775ba ("rq-qos: fix missed wake-ups in rq_qos_throttle")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20210607112613.25344-1-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f1c74a6c07e76fcb31a4bcc1f437c4361a2674ce upstream.
Trying to get the AB8500 charging driver working I ran into a bit
of bitrot: we haven't used the driver for a while so errors in
refactorings won't be noticed.
This one is pretty self evident: use argument to the macro or we
end up with a random pointer to something else.
Cc: stable@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Marcus Cooper <codekipper@gmail.com>
Fixes: 297d716f6260 ("power_supply: Change ownership from driver to core")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d8ea148e553e1dd4e80a87741abdfb229e2b323 ]
Th_strings arrays netdev_features_strings, tunable_strings, and
phy_tunable_strings has been moved to file net/ethtool/common.c.
So fixes the comment.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c9c9762d4d44dcb1b2ba90cfb4122dc11ceebf31 upstream.
After commit 07173c3ec276 ("block: enable multipage bvecs"), a bvec can
have multiple pages. But bio_will_gap() still assumes one page bvec while
checking for merging. If the pages in the bvec go across the
seg_boundary_mask, this check for merging can potentially succeed if only
the 1st page is tested, and can fail if all the pages are tested.
Later, when SCSI builds the SG list the same check for merging is done in
__blk_segment_map_sg_merge() with all the pages in the bvec tested. This
time the check may fail if the pages in bvec go across the
seg_boundary_mask (but tested okay in bio_will_gap() earlier, so those
BIOs were merged). If this check fails, we end up with a broken SG list
for drivers assuming the SG list not having offsets in intermediate pages.
This results in incorrect pages written to the disk.
Fix this by returning the multi-page bvec when testing gaps for merging.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Jeffle Xu <jefflexu@linux.alibaba.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 07173c3ec276 ("block: enable multipage bvecs")
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/1623094445-22332-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
iio_push_to_buffers_with_timestamp()
[ Upstream commit 8dea228b174ac9637b567e5ef54f4c40db4b3c41 ]
The samples buffer is passed to iio_push_to_buffers_with_timestamp()
which requires a buffer aligned to 8 bytes as it is assumed that
the timestamp will be naturally aligned if present.
Fixes tag is inaccurate but prior to that likely manual backporting needed
(for anything before 4.18) Earlier than that the include file to fix is
drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.h:
commit 974e6f02e27 ("iio: cros_ec_sensors_core: Add common functions
for the ChromeOS EC Sensor Hub.") present since kernel stable 4.10.
(Thanks to Gwendal for tracking this down)
Fixes: 5a0b8cb46624c ("iio: cros_ec: Move cros_ec_sensors_core.h in /include")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org
Link: https://lore.kernel.org/r/20210501171352.512953-7-jic23@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d327ea15a305024ef0085252fa3657bbb1ce25f5 ]
sparse generates the following warning:
include/linux/prandom.h:114:45: sparse: sparse: cast truncates bits from
constant value
This is because the 64-bit seed value is manipulated and then placed in a
u32, causing an implicit cast and truncation. A forced cast to u32 doesn't
prevent this warning, which is reasonable because a typecast doesn't prove
that truncation was expected.
Logical-AND the value with 0xffffffff to make explicit that truncation to
32-bit is intended.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20210525122012.6336-3-rf@opensource.cirrus.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9913d5745bd720c4266805c8d29952a3702e4eca upstream.
All internal use cases for tracepoint_probe_register() is set to not ever
be called with the same function and data. If it is, it is considered a
bug, as that means the accounting of handling tracepoints is corrupted.
If the function and data for a tracepoint is already registered when
tracepoint_probe_register() is called, it will call WARN_ON_ONCE() and
return with EEXISTS.
The BPF system call can end up calling tracepoint_probe_register() with
the same data, which now means that this can trigger the warning because
of a user space process. As WARN_ON_ONCE() should not be called because
user space called a system call with bad data, there needs to be a way to
register a tracepoint without triggering a warning.
Enter tracepoint_probe_register_may_exist(), which can be called, but will
not cause a WARN_ON() if the probe already exists. It will still error out
with EEXIST, which will then be sent to the user space that performed the
BPF system call.
This keeps the previous testing for issues with other users of the
tracepoint code, while letting BPF call it with duplicated data and not
warn about it.
Link: https://lore.kernel.org/lkml/20210626135845.4080-1-penguin-kernel@I-love.SAKURA.ne.jp/
Link: https://syzkaller.appspot.com/bug?id=41f4318cf01762389f4d1c1c459da4f542fe5153
Cc: stable@vger.kernel.org
Fixes: c4f6699dfcb85 ("bpf: introduce BPF_RAW_TRACEPOINT")
Reported-by: syzbot <syzbot+721aa903751db87aa244@syzkaller.appspotmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot+721aa903751db87aa244@syzkaller.appspotmail.com
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit fe19bd3dae3d15d2fbfdb3de8839a6ea0fe94264 ]
If more than one futex is placed on a shmem huge page, it can happen
that waking the second wakes the first instead, and leaves the second
waiting: the key's shared.pgoff is wrong.
When 3.11 commit 13d60f4b6ab5 ("futex: Take hugepages into account when
generating futex_key"), the only shared huge pages came from hugetlbfs,
and the code added to deal with its exceptional page->index was put into
hugetlb source. Then that was missed when 4.8 added shmem huge pages.
page_to_pgoff() is what others use for this nowadays: except that, as
currently written, it gives the right answer on hugetlbfs head, but
nonsense on hugetlbfs tails. Fix that by calling hugetlbfs-specific
hugetlb_basepage_index() on PageHuge tails as well as on head.
Yes, it's unconventional to declare hugetlb_basepage_index() there in
pagemap.h, rather than in hugetlb.h; but I do not expect anything but
page_to_pgoff() ever to need it.
[akpm@linux-foundation.org: give hugetlb_basepage_index() prototype the correct scope]
Link: https://lkml.kernel.org/r/b17d946b-d09-326e-b42a-52884c36df32@google.com
Fixes: 800d8c63b2e9 ("shmem: add huge pages support")
Reported-by: Neel Natu <neelnatu@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Zhang Yi <wetpzy@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note on stable backport: leave redundant #include <linux/hugetlb.h>
in kernel/futex.c, to avoid conflict over the header files included.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 22061a1ffabdb9c3385de159c5db7aac3a4df1cc ]
There is a race between THP unmapping and truncation, when truncate sees
pmd_none() and skips the entry, after munmap's zap_huge_pmd() cleared
it, but before its page_remove_rmap() gets to decrement
compound_mapcount: generating false "BUG: Bad page cache" reports that
the page is still mapped when deleted. This commit fixes that, but not
in the way I hoped.
The first attempt used try_to_unmap(page, TTU_SYNC|TTU_IGNORE_MLOCK)
instead of unmap_mapping_range() in truncate_cleanup_page(): it has
often been an annoyance that we usually call unmap_mapping_range() with
no pages locked, but there apply it to a single locked page.
try_to_unmap() looks more suitable for a single locked page.
However, try_to_unmap_one() contains a VM_BUG_ON_PAGE(!pvmw.pte,page):
it is used to insert THP migration entries, but not used to unmap THPs.
Copy zap_huge_pmd() and add THP handling now? Perhaps, but their TLB
needs are different, I'm too ignorant of the DAX cases, and couldn't
decide how far to go for anon+swap. Set that aside.
The second attempt took a different tack: make no change in truncate.c,
but modify zap_huge_pmd() to insert an invalidated huge pmd instead of
clearing it initially, then pmd_clear() between page_remove_rmap() and
unlocking at the end. Nice. But powerpc blows that approach out of the
water, with its serialize_against_pte_lookup(), and interesting pgtable
usage. It would need serious help to get working on powerpc (with a
minor optimization issue on s390 too). Set that aside.
Just add an "if (page_mapped(page)) synchronize_rcu();" or other such
delay, after unmapping in truncate_cleanup_page()? Perhaps, but though
that's likely to reduce or eliminate the number of incidents, it would
give less assurance of whether we had identified the problem correctly.
This successful iteration introduces "unmap_mapping_page(page)" instead
of try_to_unmap(), and goes the usual unmap_mapping_range_tree() route,
with an addition to details. Then zap_pmd_range() watches for this
case, and does spin_unlock(pmd_lock) if so - just like
page_vma_mapped_walk() now does in the PVMW_SYNC case. Not pretty, but
safe.
Note that unmap_mapping_page() is doing a VM_BUG_ON(!PageLocked) to
assert its interface; but currently that's only used to make sure that
page->mapping is stable, and zap_pmd_range() doesn't care if the page is
locked or not. Along these lines, in invalidate_inode_pages2_range()
move the initial unmap_mapping_range() out from under page lock, before
then calling unmap_mapping_page() under page lock if still mapped.
Link: https://lkml.kernel.org/r/a2a4a148-cdd8-942c-4ef8-51b77f643dbe@google.com
Fixes: fc127da085c2 ("truncate: handle file thp")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note on stable backport: fixed up call to truncate_cleanup_page()
in truncate_inode_pages_range(). Use hpage_nr_pages() in
unmap_mapping_page().
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 732ed55823fc3ad998d43b86bf771887bcc5ec67 ]
Stressing huge tmpfs often crashed on unmap_page()'s VM_BUG_ON_PAGE
(!unmap_success): with dump_page() showing mapcount:1, but then its raw
struct page output showing _mapcount ffffffff i.e. mapcount 0.
And even if that particular VM_BUG_ON_PAGE(!unmap_success) is removed,
it is immediately followed by a VM_BUG_ON_PAGE(compound_mapcount(head)),
and further down an IS_ENABLED(CONFIG_DEBUG_VM) total_mapcount BUG():
all indicative of some mapcount difficulty in development here perhaps.
But the !CONFIG_DEBUG_VM path handles the failures correctly and
silently.
I believe the problem is that once a racing unmap has cleared pte or
pmd, try_to_unmap_one() may skip taking the page table lock, and emerge
from try_to_unmap() before the racing task has reached decrementing
mapcount.
Instead of abandoning the unsafe VM_BUG_ON_PAGE(), and the ones that
follow, use PVMW_SYNC in try_to_unmap_one() in this case: adding
TTU_SYNC to the options, and passing that from unmap_page().
When CONFIG_DEBUG_VM, or for non-debug too? Consensus is to do the same
for both: the slight overhead added should rarely matter, except perhaps
if splitting sparsely-populated multiply-mapped shmem. Once confident
that bugs are fixed, TTU_SYNC here can be removed, and the race
tolerated.
Link: https://lkml.kernel.org/r/c1e95853-8bcd-d8fd-55fa-e7f2488e78f@google.com
Fixes: fec89c109f3a ("thp: rewrite freeze_page()/unfreeze_page() with generic rmap walkers")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note on stable backport: upstream TTU_SYNC 0x10 takes the value which
5.11 commit 013339df116c ("mm/rmap: always do TTU_IGNORE_ACCESS") freed.
It is very tempting to backport that commit (as 5.10 already did) and
make no change here; but on reflection, good as that commit is, I'm
reluctant to include any possible side-effect of it in this series.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b77e8c8cde581dadab9a0f1543a347e24315f11 upstream.
Most callers of is_huge_zero_pmd() supply a pmd already verified
present; but a few (notably zap_huge_pmd()) do not - it might be a pmd
migration entry, in which the pfn is encoded differently from a present
pmd: which might pass the is_huge_zero_pmd() test (though not on x86,
since L1TF forced us to protect against that); or perhaps even crash in
pmd_page() applied to a swap-like entry.
Make it safe by adding pmd_present() check into is_huge_zero_pmd()
itself; and make it quicker by saving huge_zero_pfn, so that
is_huge_zero_pmd() will not need to do that pmd_page() lookup each time.
__split_huge_pmd_locked() checked pmd_trans_huge() before: that worked,
but is unnecessary now that is_huge_zero_pmd() checks present.
Link: https://lkml.kernel.org/r/21ea9ca-a1f5-8b90-5e88-95fb1c49bbfa@google.com
Fixes: e71769ae5260 ("mm: enable thp migration for shmem thp")
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Yang Shi <shy828301@gmail.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jue Wang <juew@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Peter Xu <peterx@redhat.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Wang Yugui <wangyugui@e16-tech.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a4055888629bc0467d12d912cd7c90acdf3d9b12 part ]
Add VM_WARN_ON_ONCE_PAGE() macro.
Link: https://lkml.kernel.org/r/1604283436-18880-3-git-send-email-alex.shi@linux.alibaba.com
Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note on stable backport: original commit was titled
mm/memcg: warning on !memcg after readahead page charged
which included uses of this macro in mm/memcontrol.c: here omitted.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25de4ce5ed02994aea8bc111d133308f6fd62566 upstream.
There is a timer wrap issue on dra7 for the ARM architected timer.
In a typical clock configuration the timer fails to wrap after 388 days.
To work around the issue, we need to use timer-ti-dm percpu timers instead.
Let's configure dmtimer3 and 4 as percpu timers by default, and warn about
the issue if the dtb is not configured properly.
For more information, please see the errata for "AM572x Sitara Processors
Silicon Revisions 1.1, 2.0":
https://www.ti.com/lit/er/sprz429m/sprz429m.pdf
The concept is based on earlier reference patches done by Tero Kristo and
Keerthy.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <kristo@kernel.org>
[tony@atomide.com: backported to 5.4.y]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0514582a1a5b4ac1a3fd64792826d392d7ae9ddc ]
The valid selectors for bd70528 bucks are 0 ~ 0xf, so the .n_voltages
should be 16 (0x10). Use 0x10 to make it consistent with BD70528_LDO_VOLTS.
Also remove redundant defines for BD70528_BUCK_VOLTS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210523071045.2168904-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 475b92f932168a78da8109acd10bfb7578b8f2bb ]
Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).
The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.
Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.
Fixes: d39a743511cd ("ptp: validate the requested frequency adjustment.")
Fixes: d94ba80ebbea ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ea6932d70e223e02fea3ae20a4feff05d7c1ea9a ]
There is a panic in socket ioctl cmd SIOCGSKNS when NET_NS is not enabled.
The reason is that nsfs tries to access ns->ops but the proc_ns_operations
is not implemented in this case.
[7.670023] Unable to handle kernel NULL pointer dereference at virtual address 00000010
[7.670268] pgd = 32b54000
[7.670544] [00000010] *pgd=00000000
[7.671861] Internal error: Oops: 5 [#1] SMP ARM
[7.672315] Modules linked in:
[7.672918] CPU: 0 PID: 1 Comm: systemd Not tainted 5.13.0-rc3-00375-g6799d4f2da49 #16
[7.673309] Hardware name: Generic DT based system
[7.673642] PC is at nsfs_evict+0x24/0x30
[7.674486] LR is at clear_inode+0x20/0x9c
The same to tun SIOCGSKNS command.
To fix this problem, we make get_net_ns() return -EINVAL when NET_NS is
disabled. Meanwhile move it to right place net/core/net_namespace.c.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Fixes: c62cce2caee5 ("net: add an ioctl to get a socket network namespace")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a3e5fd9314dfc4314a9567cde96e1aef83a7458a ]
When adding a hairpin flow, a firmware-side send queue is created for
the peer net device, which claims some host memory pages for its
internal ring buffer. If the peer net device is removed/unbound before
the hairpin flow is deleted, then the send queue is not destroyed which
leads to a stack trace on pci device remove:
[ 748.005230] mlx5_core 0000:08:00.2: wait_func:1094:(pid 12985): MANAGE_PAGES(0x108) timeout. Will cause a leak of a command resource
[ 748.005231] mlx5_core 0000:08:00.2: reclaim_pages:514:(pid 12985): failed reclaiming pages: err -110
[ 748.001835] mlx5_core 0000:08:00.2: mlx5_reclaim_root_pages:653:(pid 12985): failed reclaiming pages (-110) for func id 0x0
[ 748.002171] ------------[ cut here ]------------
[ 748.001177] FW pages counter is 4 after reclaiming all pages
[ 748.001186] WARNING: CPU: 1 PID: 12985 at drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:685 mlx5_reclaim_startup_pages+0x34b/0x460 [mlx5_core] [ +0.002771] Modules linked in: cls_flower mlx5_ib mlx5_core ptp pps_core act_mirred sch_ingress openvswitch nsh xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm ib_umad ib_ipoib iw_cm ib_cm ib_uverbs ib_core overlay fuse [last unloaded: pps_core]
[ 748.007225] CPU: 1 PID: 12985 Comm: tee Not tainted 5.12.0+ #1
[ 748.001376] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 748.002315] RIP: 0010:mlx5_reclaim_startup_pages+0x34b/0x460 [mlx5_core]
[ 748.001679] Code: 28 00 00 00 0f 85 22 01 00 00 48 81 c4 b0 00 00 00 31 c0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 48 c7 c7 40 cc 19 a1 e8 9f 71 0e e2 <0f> 0b e9 30 ff ff ff 48 c7 c7 a0 cc 19 a1 e8 8c 71 0e e2 0f 0b e9
[ 748.003781] RSP: 0018:ffff88815220faf8 EFLAGS: 00010286
[ 748.001149] RAX: 0000000000000000 RBX: ffff8881b4900280 RCX: 0000000000000000
[ 748.001445] RDX: 0000000000000027 RSI: 0000000000000004 RDI: ffffed102a441f51
[ 748.001614] RBP: 00000000000032b9 R08: 0000000000000001 R09: ffffed1054a15ee8
[ 748.001446] R10: ffff8882a50af73b R11: ffffed1054a15ee7 R12: fffffbfff07c1e30
[ 748.001447] R13: dffffc0000000000 R14: ffff8881b492cba8 R15: 0000000000000000
[ 748.001429] FS: 00007f58bd08b580(0000) GS:ffff8882a5080000(0000) knlGS:0000000000000000
[ 748.001695] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 748.001309] CR2: 000055a026351740 CR3: 00000001d3b48006 CR4: 0000000000370ea0
[ 748.001506] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 748.001483] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 748.001654] Call Trace:
[ 748.000576] ? mlx5_satisfy_startup_pages+0x290/0x290 [mlx5_core]
[ 748.001416] ? mlx5_cmd_teardown_hca+0xa2/0xd0 [mlx5_core]
[ 748.001354] ? mlx5_cmd_init_hca+0x280/0x280 [mlx5_core]
[ 748.001203] mlx5_function_teardown+0x30/0x60 [mlx5_core]
[ 748.001275] mlx5_uninit_one+0xa7/0xc0 [mlx5_core]
[ 748.001200] remove_one+0x5f/0xc0 [mlx5_core]
[ 748.001075] pci_device_remove+0x9f/0x1d0
[ 748.000833] device_release_driver_internal+0x1e0/0x490
[ 748.001207] unbind_store+0x19f/0x200
[ 748.000942] ? sysfs_file_ops+0x170/0x170
[ 748.001000] kernfs_fop_write_iter+0x2bc/0x450
[ 748.000970] new_sync_write+0x373/0x610
[ 748.001124] ? new_sync_read+0x600/0x600
[ 748.001057] ? lock_acquire+0x4d6/0x700
[ 748.000908] ? lockdep_hardirqs_on_prepare+0x400/0x400
[ 748.001126] ? fd_install+0x1c9/0x4d0
[ 748.000951] vfs_write+0x4d0/0x800
[ 748.000804] ksys_write+0xf9/0x1d0
[ 748.000868] ? __x64_sys_read+0xb0/0xb0
[ 748.000811] ? filp_open+0x50/0x50
[ 748.000919] ? syscall_enter_from_user_mode+0x1d/0x50
[ 748.001223] do_syscall_64+0x3f/0x80
[ 748.000892] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 748.001026] RIP: 0033:0x7f58bcfb22f7
[ 748.000944] Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
[ 748.003925] RSP: 002b:00007fffd7f2aaa8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 748.001732] RAX: ffffffffffffffda RBX: 000000000000000d RCX: 00007f58bcfb22f7
[ 748.001426] RDX: 000000000000000d RSI: 00007fffd7f2abc0 RDI: 0000000000000003
[ 748.001746] RBP: 00007fffd7f2abc0 R08: 0000000000000000 R09: 0000000000000001
[ 748.001631] R10: 00000000000001b6 R11: 0000000000000246 R12: 000000000000000d
[ 748.001537] R13: 00005597ac2c24a0 R14: 000000000000000d R15: 00007f58bd084700
[ 748.001564] irq event stamp: 0
[ 748.000787] hardirqs last enabled at (0): [<0000000000000000>] 0x0
[ 748.001399] hardirqs last disabled at (0): [<ffffffff813132cf>] copy_process+0x146f/0x5eb0
[ 748.001854] softirqs last enabled at (0): [<ffffffff8131330e>] copy_process+0x14ae/0x5eb0
[ 748.013431] softirqs last disabled at (0): [<0000000000000000>] 0x0
[ 748.001492] ---[ end trace a6fabd773d1c51ae ]---
Fix by destroying the send queue of a hairpin peer net device that is
being removed/unbound, which returns the allocated ring buffer pages to
the host.
Fixes: 4d8fcf216c90 ("net/mlx5e: Avoid unbounded peer devices when unpairing TC hairpin rules")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6be388f4a35d2ce5ef7dbf635a8964a5da7f799f ]
In hid_submit_ctrl(), the way of calculating the report length doesn't
take into account that report->size can be zero. When running the
syzkaller reproducer, a report of size 0 causes hid_submit_ctrl) to
calculate transfer_buffer_length as 16384. When this urb is passed to
the usb core layer, KMSAN reports an info leak of 16384 bytes.
To fix this, first modify hid_report_len() to account for the zero
report size case by using DIV_ROUND_UP for the division. Then, call it
from hid_submit_ctrl().
Reported-by: syzbot+7c2bb71996f95a82524c@syzkaller.appspotmail.com
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 4422829e8053068e0225e4d0ef42dc41ea7c9ef5 upstream.
array_index_nospec does not work for uint64_t on 32-bit builds.
However, the size of a memory slot must be less than 20 bits wide
on those system, since the memory slot must fit in the user
address space. So just store it in an unsigned long.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 404e5a12691fe797486475fe28cc0b80cb8bef2c upstream.
Currently when mlx4 maps the hca_core_clock page to the user space there
are read-modifiable registers, one of which is semaphore, on this page as
well as the clock counter. If user reads the wrong offset, it can modify
the semaphore and hang the device.
Do not map the hca_core_clock page to the user space unless the device has
been put in a backwards compatibility mode to support this feature.
After this patch, mlx4 core_clock won't be mapped to user space on the
majority of existing devices and the uverbs device time feature in
ibv_query_rt_values_ex() will be disabled.
Fixes: 52033cfb5aab ("IB/mlx4: Add mmap call to map the hardware clock")
Link: https://lore.kernel.org/r/9632304e0d6790af84b3b706d8c18732bc0d5e27.1622726305.git.leonro@nvidia.com
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6490fa565534fa83593278267785a694fd378a2b upstream.
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit da27a83fd6cc7780fea190e1f5c19e87019da65c upstream.
KVM's mechanism for accessing guest memory translates a guest physical
address (gpa) to a host virtual address using the right-shifted gpa
(also known as gfn) and a struct kvm_memory_slot. The translation is
performed in __gfn_to_hva_memslot using the following formula:
hva = slot->userspace_addr + (gfn - slot->base_gfn) * PAGE_SIZE
It is expected that gfn falls within the boundaries of the guest's
physical memory. However, a guest can access invalid physical addresses
in such a way that the gfn is invalid.
__gfn_to_hva_memslot is called from kvm_vcpu_gfn_to_hva_prot, which first
retrieves a memslot through __gfn_to_memslot. While __gfn_to_memslot
does check that the gfn falls within the boundaries of the guest's
physical memory or not, a CPU can speculate the result of the check and
continue execution speculatively using an illegal gfn. The speculation
can result in calculating an out-of-bounds hva. If the resulting host
virtual address is used to load another guest physical address, this
is effectively a Spectre gadget consisting of two consecutive reads,
the second of which is data dependent on the first.
Right now it's not clear if there are any cases in which this is
exploitable. One interesting case was reported by the original author
of this patch, and involves visiting guest page tables on x86. Right
now these are not vulnerable because the hva read goes through get_user(),
which contains an LFENCE speculation barrier. However, there are
patches in progress for x86 uaccess.h to mask kernel addresses instead of
using LFENCE; once these land, a guest could use speculation to read
from the VMM's ring 3 address space. Other architectures such as |
