| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Cross-merge networking fixes after downstream PR (net-6.17-rc8).
Conflicts:
tools/testing/selftests/drivers/net/bonding/Makefile
87951b566446 selftests: bonding: add test for passive LACP mode
c2377f1763e9 selftests: bonding: add test for LACP actor port priority
Adjacent changes:
drivers/net/ethernet/cadence/macb.h
fca3dc859b20 net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf169e net: macb: Add TAPRIO traffic scheduling support
drivers/net/ethernet/cadence/macb_main.c
fca3dc859b20 net: macb: remove illusion about TBQPH/RBQPH being per-queue
89934dbf169e net: macb: Add TAPRIO traffic scheduling support
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The active-backup bonding mode supports XFRM ESP offload. However, when
a bond is added using command like `ip link add bond0 type bond mode 1
miimon 100`, the `ethtool -k` command shows that the XFRM ESP offload is
disabled. This occurs because, in bond_newlink(), we change bond link
first and register bond device later. So the XFRM feature update in
bond_option_mode_set() is not called as the bond device is not yet
registered, leading to the offload feature not being set successfully.
To resolve this issue, we can modify the code order in bond_newlink() to
ensure that the bond device is registered first before changing the bond
link parameters. This change will allow the XFRM ESP offload feature to be
correctly enabled.
Fixes: 007ab5345545 ("bonding: fix feature flag setting at init time")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20250925023304.472186-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove the implementation of use_carrier, the link monitoring
method that utilizes ethtool or ioctl to determine the link state of an
interface in a bond. Bonding will always behaves as if use_carrier=1,
which relies on netif_carrier_ok() to determine the link state of
interfaces.
To avoid acquiring RTNL many times per second, bonding inspects
link state under RCU, but not under RTNL. However, ethtool
implementations in drivers may sleep, and therefore this strategy is
unsuitable for use with calls into driver ethtool functions.
The use_carrier option was introduced in 2003, to provide
backwards compatibility for network device drivers that did not support
the then-new netif_carrier_ok/on/off system. Device drivers are now
expected to support netif_carrier_*, and the use_carrier backwards
compatibility logic is no longer necessary.
The option itself remains, but when queried always returns 1,
and may only be set to 1.
Link: https://lore.kernel.org/000000000000eb54bf061cfd666a@google.com
Link: https://lore.kernel.org/20240718122017.d2e33aaac43a.I10ab9c9ded97163aef4e4de10985cd8f7de60d28@changeid
Signed-off-by: Jay Vosburgh <jv@jvosburgh.net>
Reported-by: syzbot+b8c48ea38ca27d150063@syzkaller.appspotmail.com
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/2029487.1756512517@famine
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stacking technology is a type of technology used to expand ports on
Ethernet switches. It is widely used as a common access method in
large-scale Internet data center architectures. Years of practice
have proved that stacking technology has advantages and disadvantages
in high-reliability network architecture scenarios. For instance,
in stacking networking arch, conventional switch system upgrades
require multiple stacked devices to restart at the same time.
Therefore, it is inevitable that the business will be interrupted
for a while. It is for this reason that "no-stacking" in data centers
has become a trend. Additionally, when the stacking link connecting
the switches fails or is abnormal, the stack will split. Although it is
not common, it still happens in actual operation. The problem is that
after the split, it is equivalent to two switches with the same
configuration appearing in the network, causing network configuration
conflicts and ultimately interrupting the services carried by the
stacking system.
To improve network stability, "non-stacking" solutions have been
increasingly adopted, particularly by public cloud providers and
tech companies like Alibaba, Tencent, and Didi. "non-stacking" is
a method of mimicing switch stacking that convinces a LACP peer,
bonding in this case, connected to a set of "non-stacked" switches
that all of its ports are connected to a single switch
(i.e., LACP aggregator), as if those switches were stacked. This
enables the LACP peer's ports to aggregate together, and requires
(a) special switch configuration, described in the linked article,
and (b) modifications to the bonding 802.3ad (LACP) mode to send
all ARP/ND packets across all ports of the active aggregator.
Note that, with multiple aggregators, the current broadcast mode
logic will send only packets to the selected aggregator(s).
+-----------+ +-----------+
| switch1 | | switch2 |
+-----------+ +-----------+
^ ^
| |
+-----------------+
| bond4 lacp |
+-----------------+
| |
| NIC1 | NIC2
+-----------------+
| server |
+-----------------+
- https://www.ruijie.com/fr-fr/support/tech-gallery/de-stack-data-center-network-architecture/
Cc: Jay Vosburgh <jv@jvosburgh.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <horms@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Signed-off-by: Zengbing Tu <tuzengbing@didiglobal.com>
Link: https://patch.msgid.link/84d0a044514157bb856a10b6d03a1028c4883561.1751031306.git.tonghao@bamaicloud.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Following operations can trigger a warning[1]:
ip netns add ns1
ip netns exec ns1 ip link add bond0 type bond mode balance-rr
ip netns exec ns1 ip link set dev bond0 xdp obj af_xdp_kern.o sec xdp
ip netns exec ns1 ip link set bond0 type bond mode broadcast
ip netns del ns1
When delete the namespace, dev_xdp_uninstall() is called to remove xdp
program on bond dev, and bond_xdp_set() will check the bond mode. If bond
mode is changed after attaching xdp program, the warning may occur.
Some bond modes (broadcast, etc.) do not support native xdp. Set bond mode
with xdp program attached is not good. Add check for xdp program when set
bond mode.
[1]
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11 at net/core/dev.c:9912 unregister_netdevice_many_notify+0x8d9/0x930
Modules linked in:
CPU: 0 UID: 0 PID: 11 Comm: kworker/u4:0 Not tainted 6.14.0-rc4 #107
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014
Workqueue: netns cleanup_net
RIP: 0010:unregister_netdevice_many_notify+0x8d9/0x930
Code: 00 00 48 c7 c6 6f e3 a2 82 48 c7 c7 d0 b3 96 82 e8 9c 10 3e ...
RSP: 0018:ffffc90000063d80 EFLAGS: 00000282
RAX: 00000000ffffffa1 RBX: ffff888004959000 RCX: 00000000ffffdfff
RDX: 0000000000000000 RSI: 00000000ffffffea RDI: ffffc90000063b48
RBP: ffffc90000063e28 R08: ffffffff82d39b28 R09: 0000000000009ffb
R10: 0000000000000175 R11: ffffffff82d09b40 R12: ffff8880049598e8
R13: 0000000000000001 R14: dead000000000100 R15: ffffc90000045000
FS: 0000000000000000(0000) GS:ffff888007a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000d406b60 CR3: 000000000483e000 CR4: 00000000000006f0
Call Trace:
<TASK>
? __warn+0x83/0x130
? unregister_netdevice_many_notify+0x8d9/0x930
? report_bug+0x18e/0x1a0
? handle_bug+0x54/0x90
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? unregister_netdevice_many_notify+0x8d9/0x930
? bond_net_exit_batch_rtnl+0x5c/0x90
cleanup_net+0x237/0x3d0
process_one_work+0x163/0x390
worker_thread+0x293/0x3b0
? __pfx_worker_thread+0x10/0x10
kthread+0xec/0x1e0
? __pfx_kthread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2f/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: 9e2ee5c7e7c3 ("net, bonding: Add XDP support to the bonding driver")
Signed-off-by: Wang Liang <wangliang74@huawei.com>
Acked-by: Jussi Maki <joamaki@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://patch.msgid.link/20250321044852.1086551-1-wangliang74@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the cited commit, bond->ipsec_lock is added to protect ipsec_list,
hence xdo_dev_state_add and xdo_dev_state_delete are called inside
this lock. As ipsec_lock is a spin lock and such xfrmdev ops may sleep,
"scheduling while atomic" will be triggered when changing bond's
active slave.
[ 101.055189] BUG: scheduling while atomic: bash/902/0x00000200
[ 101.055726] Modules linked in:
[ 101.058211] CPU: 3 PID: 902 Comm: bash Not tainted 6.9.0-rc4+ #1
[ 101.058760] Hardware name:
[ 101.059434] Call Trace:
[ 101.059436] <TASK>
[ 101.060873] dump_stack_lvl+0x51/0x60
[ 101.061275] __schedule_bug+0x4e/0x60
[ 101.061682] __schedule+0x612/0x7c0
[ 101.062078] ? __mod_timer+0x25c/0x370
[ 101.062486] schedule+0x25/0xd0
[ 101.062845] schedule_timeout+0x77/0xf0
[ 101.063265] ? asm_common_interrupt+0x22/0x40
[ 101.063724] ? __bpf_trace_itimer_state+0x10/0x10
[ 101.064215] __wait_for_common+0x87/0x190
[ 101.064648] ? usleep_range_state+0x90/0x90
[ 101.065091] cmd_exec+0x437/0xb20 [mlx5_core]
[ 101.065569] mlx5_cmd_do+0x1e/0x40 [mlx5_core]
[ 101.066051] mlx5_cmd_exec+0x18/0x30 [mlx5_core]
[ 101.066552] mlx5_crypto_create_dek_key+0xea/0x120 [mlx5_core]
[ 101.067163] ? bonding_sysfs_store_option+0x4d/0x80 [bonding]
[ 101.067738] ? kmalloc_trace+0x4d/0x350
[ 101.068156] mlx5_ipsec_create_sa_ctx+0x33/0x100 [mlx5_core]
[ 101.068747] mlx5e_xfrm_add_state+0x47b/0xaa0 [mlx5_core]
[ 101.069312] bond_change_active_slave+0x392/0x900 [bonding]
[ 101.069868] bond_option_active_slave_set+0x1c2/0x240 [bonding]
[ 101.070454] __bond_opt_set+0xa6/0x430 [bonding]
[ 101.070935] __bond_opt_set_notify+0x2f/0x90 [bonding]
[ 101.071453] bond_opt_tryset_rtnl+0x72/0xb0 [bonding]
[ 101.071965] bonding_sysfs_store_option+0x4d/0x80 [bonding]
[ 101.072567] kernfs_fop_write_iter+0x10c/0x1a0
[ 101.073033] vfs_write+0x2d8/0x400
[ 101.073416] ? alloc_fd+0x48/0x180
[ 101.073798] ksys_write+0x5f/0xe0
[ 101.074175] do_syscall_64+0x52/0x110
[ 101.074576] entry_SYSCALL_64_after_hwframe+0x4b/0x53
As bond_ipsec_add_sa_all and bond_ipsec_del_sa_all are only called
from bond_change_active_slave, which requires holding the RTNL lock.
And bond_ipsec_add_sa and bond_ipsec_del_sa are xfrm state
xdo_dev_state_add and xdo_dev_state_delete APIs, which are in user
context. So ipsec_lock doesn't have to be spin lock, change it to
mutex, and thus the above issue can be resolved.
Fixes: 9a5605505d9c ("bonding: Add struct bond_ipesc to manage SA")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20240823031056.110999-4-jianbol@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the independent control state machine per IEEE
802.1AX-2008 5.4.15 in addition to the existing implementation of the
coupled control state machine.
Introduces two new states, AD_MUX_COLLECTING and AD_MUX_DISTRIBUTING in
the LACP MUX state machine for separated handling of an initial
Collecting state before the Collecting and Distributing state. This
enables a port to be in a state where it can receive incoming packets
while not still distributing. This is useful for reducing packet loss when
a port begins distributing before its partner is able to collect.
Added new functions such as bond_set_slave_tx_disabled_flags and
bond_set_slave_rx_enabled_flags to precisely manage the port's collecting
and distributing states. Previously, there was no dedicated method to
disable TX while keeping RX enabled, which this patch addresses.
Note that the regular flow process in the kernel's bonding driver remains
unaffected by this patch. The extension requires explicit opt-in by the
user (in order to ensure no disruptions for existing setups) via netlink
support using the new bonding parameter coupled_control. The default value
for coupled_control is set to 1 so as to preserve existing behaviour.
Signed-off-by: Aahil Awatramani <aahila@google.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240202175858.1573852-1-aahila@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commit 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode
bonds") aims to enable the use of macvlans on top of rlb bond mode. However,
the current rlb bond mode only handles ARP packets to update remote neighbor
entries. This causes an issue when a macvlan is on top of the bond, and
remote devices send packets to the macvlan using the bond's MAC address
as the destination. After delivering the packets to the macvlan, the macvlan
will rejects them as the MAC address is incorrect. Consequently, this commit
makes macvlan over bond non-functional.
To address this problem, one potential solution is to check for the presence
of a macvlan port on the bond device using netif_is_macvlan_port(bond->dev)
and return NULL in the rlb_arp_xmit() function. However, this approach
doesn't fully resolve the situation when a VLAN exists between the bond and
macvlan.
So let's just do a partial revert for commit 14af9963ba1e in rlb_arp_xmit().
As the comment said, Don't modify or load balance ARPs that do not originate
locally.
Fixes: 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode bonds")
Reported-by: susan.zheng@veritas.com
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2117816
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Change an errant kernel-doc comment marker (/**) to a regular
comment to prevent a kernel-doc warning.
bonding.h:282: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Returns NULL if the net_device does not belong to any of the bond's slaves
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Link: https://lore.kernel.org/r/20230714045127.18752-2-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/raw.c
3632679d9e4f ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
c85be08fc4fa ("raw: Stop using RTO_ONLINK.")
https://lore.kernel.org/all/20230525110037.2b532b83@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/freescale/fec_main.c
9025944fddfe ("net: fec: add dma_wmb to ensure correct descriptor values")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the virtual interface's feature is updated, it synchronizes the
updated feature for its own lower interface.
This propagation logic should be worked as the iteration, not recursively.
But it works recursively due to the netdev notification unexpectedly.
This problem occurs when it disables LRO only for the team and bonding
interface type.
team0
|
+------+------+-----+-----+
| | | | |
team1 team2 team3 ... team200
If team0's LRO feature is updated, it generates the NETDEV_FEAT_CHANGE
event to its own lower interfaces(team1 ~ team200).
It is worked by netdev_sync_lower_features().
So, the NETDEV_FEAT_CHANGE notification logic of each lower interface
work iteratively.
But generated NETDEV_FEAT_CHANGE event is also sent to the upper
interface too.
upper interface(team0) generates the NETDEV_FEAT_CHANGE event for its own
lower interfaces again.
lower and upper interfaces receive this event and generate this
event again and again.
So, the stack overflow occurs.
But it is not the infinite loop issue.
Because the netdev_sync_lower_features() updates features before
generating the NETDEV_FEAT_CHANGE event.
Already synchronized lower interfaces skip notification logic.
So, it is just the problem that iteration logic is changed to the
recursive unexpectedly due to the notification mechanism.
Reproducer:
ip link add team0 type team
ethtool -K team0 lro on
for i in {1..200}
do
ip link add team$i master team0 type team
ethtool -K team$i lro on
done
ethtool -K team0 lro off
In order to fix it, the notifier_ctx member of bonding/team is introduced.
Reported-by: syzbot+60748c96cf5c6df8e581@syzkaller.appspotmail.com
Fixes: fd867d51f889 ("net/core: generic support for disabling netdev features down stack")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20230517143010.3596250-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previous batches of SPDX conversion missed bond_main.c and bonding_priv.h
because these files doesn't mention intended GPL version. Add SPDX identifier
to these files, assuming GPL 1.0+.
Cc: Thomas Davis <tadavis@lbl.gov>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Bonding send_peer_notif was defined as u8. Since commit 07a4ddec3ce9
("bonding: add an option to specify a delay between peer notifications").
the bond->send_peer_notif will be num_peer_notif multiplied by
peer_notif_delay, which is u8 * u32. This would cause the send_peer_notif
overflow easily. e.g.
ip link add bond0 type bond mode 1 miimon 100 num_grat_arp 30 peer_notify_delay 1000
To fix the overflow, let's set the send_peer_notif to u32 and limit
peer_notif_delay to 300s.
Reported-by: Liang Li <liali@redhat.com>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2090053
Fixes: 07a4ddec3ce9 ("bonding: add an option to specify a delay between peer notifications")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce xdp_features support for bonding driver according to the slave
devices attached to the master one. xdp_features is required whenever we
want to xdp_redirect traffic into a bond device and then into selected
slaves attached to it.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jussi Maki <joamaki@gmail.com>
Tested-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.
However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.
Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.
Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bond agnostically interacts with TLS device-offload requests via the
.ndo_sk_get_lower_dev operation. Return value is true iff bond
guarantees fixed mapping between the TLS connection and a lower netdev.
Due to this nature, the bond TLS device offload features are not
explicitly controllable in the bond layer. As of today, these are
read-only values based on the evaluation of bond_sk_check(). However,
this indication might be incorrect and misleading, when the feature bits
are "fixed" by some dependency features. For example,
NETIF_F_HW_TLS_TX/RX are forcefully cleared in case the corresponding
checksum offload is disabled. But in fact the bond ability to still
offload TLS connections to the lower device is not hurt.
This means that these bits can not be trusted, and hence better become
unused.
This patch revives some old discussion [1] and proposes a much simpler
solution: Clear the bond's TLS features bits. Everyone should stop
reading them.
[1] https://lore.kernel.org/netdev/20210526095747.22446-1-tariqt@nvidia.com/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20221025105300.4718-1-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are already a few definitions of arrays containing
MULTICAST_LACPDU_ADDR and the next patch will add one more use. These all
contain the same constant data so define one common instance for all
bonding code.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding driver piggybacks on time stamps kept by the network stack
for the purpose of the netdev TX watchdog, and this is problematic
because it does not work with NETIF_F_LLTX devices.
It is hard to say why the driver looks at dev_trans_start() of the
slave->dev, considering that this is updated even by non-ARP/NS probes
sent by us, and even by traffic not sent by us at all (for example PTP
on physical slave devices). ARP monitoring in active-backup mode appears
to still work even if we track only the last TX time of actual ARP
probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add per port priority support for bonding active slave re-selection during
failover. A higher number means higher priority in selection. The primary
slave still has the highest priority. This option also follows the
primary_reselect rules.
This option could only be configured via netlink.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().
Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before adding yet another possibly contended atomic_long_t,
it is time to add per-cpu storage for existing ones:
dev->tx_dropped, dev->rx_dropped, and dev->rx_nohandler
Because many devices do not have to increment such counters,
allocate the per-cpu storage on demand, so that dev_get_stats()
does not have to spend considerable time folding zero counters.
Note that some drivers have abused these counters which
were supposed to be only used by core networking stack.
v4: should use per_cpu_ptr() in dev_get_stats() (Jakub)
v3: added a READ_ONCE() in netdev_core_stats_alloc() (Paolo)
v2: add a missing include (reported by kernel test robot <lkp@intel.com>)
Change in netdev_core_stats_alloc() (Jakub)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: jeffreyji <jeffreyji@google.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220311051420.2608812-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch add a new bonding option ns_ip6_target, which correspond
to the arp_ip_target. With this we set IPv6 targets and send IPv6 NS
request to determine the health of the link.
For other related options like the validation, we still use
arp_validate, and will change to ns_validate later.
Note: the sysfs configuration support was removed based on
https://lore.kernel.org/netdev/8863.1645071997@famine
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new bonding parameter ns_targets to store IPv6 address.
Add required bond_ns_send/rcv functions first before adding
IPv6 address option setting.
Add two functions bond_send/rcv_validate so we can send/recv
ARP and NS at the same time.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No caller since v3.16.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bond_option_active_slave_get_rcu() should not be used in rtnl_mutex as it
use rcu_dereference(). Replace to rcu_dereference_rtnl() so we also can use
this function in rtnl protected context.
With this update, we can rmeove the rcu_read_lock/unlock in
bonding .ndo_eth_ioctl and .get_ts_info.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP ioctl to active device")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we use hard code number to verify if we are in the
arp_interval timeslice. But some user may want to reduce/extend
the verify timeslice. With the similar team option 'missed_max'
the uers could change that number based on their own environment.
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All of the symbols either only exist in bond_options.c or nowhere at
all. These symbols were verified to not exist in the code base by
using `git grep` and their removal was verified by compiling bonding.ko.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
bpf-next 2021-08-10
We've added 31 non-merge commits during the last 8 day(s) which contain
a total of 28 files changed, 3644 insertions(+), 519 deletions(-).
1) Native XDP support for bonding driver & related BPF selftests, from Jussi Maki.
2) Large batch of new BPF JIT tests for test_bpf.ko that came out as a result from
32-bit MIPS JIT development, from Johan Almbladh.
3) Rewrite of netcnt BPF selftest and merge into test_progs, from Stanislav Fomichev.
4) Fix XDP bpf_prog_test_run infra after net to net-next merge, from Andrii Nakryiko.
5) Follow-up fix in unix_bpf_update_proto() to enforce socket type, from Cong Wang.
6) Fix bpf-iter-tcp4 selftest to print the correct dest IP, from Jose Blanquicet.
7) Various misc BPF XDP sample improvements, from Niklas Söderlund, Matthew Cover,
and Muhammad Falak R Wani.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (31 commits)
bpf, tests: Add tail call test suite
bpf, tests: Add tests for BPF_CMPXCHG
bpf, tests: Add tests for atomic operations
bpf, tests: Add test for 32-bit context pointer argument passing
bpf, tests: Add branch conversion JIT test
bpf, tests: Add word-order tests for load/store of double words
bpf, tests: Add tests for ALU operations implemented with function calls
bpf, tests: Add more ALU64 BPF_MUL tests
bpf, tests: Add more BPF_LSH/RSH/ARSH tests for ALU64
bpf, tests: Add more ALU32 tests for BPF_LSH/RSH/ARSH
bpf, tests: Add more tests of ALU32 and ALU64 bitwise operations
bpf, tests: Fix typos in test case descriptions
bpf, tests: Add BPF_MOV tests for zero and sign extension
bpf, tests: Add BPF_JMP32 test cases
samples, bpf: Add an explict comment to handle nested vlan tagging.
selftests/bpf: Add tests for XDP bonding
selftests/bpf: Fix xdp_tx.c prog section name
net, core: Allow netdev_lower_get_next_private_rcu in bh context
bpf, devmap: Exclude XDP broadcast to master device
net, bonding: Add XDP support to the bonding driver
...
====================
Link: https://lore.kernel.org/r/20210810130038.16927-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
XDP is implemented in the bonding driver by transparently delegating
the XDP program loading, removal and xmit operations to the bonding
slave devices. The overall goal of this work is that XDP programs
can be attached to a bond device *without* any further changes (or
awareness) necessary to the program itself, meaning the same XDP
program can be attached to a native device but also a bonding device.
Semantics of XDP_TX when attached to a bond are equivalent in such
setting to the case when a tc/BPF program would be attached to the
bond, meaning transmitting the packet out of the bond itself using one
of the bond's configured xmit methods to select a slave device (rather
than XDP_TX on the slave itself). Handling of XDP_TX to transmit
using the configured bonding mechanism is therefore implemented by
rewriting the BPF program return value in bpf_prog_run_xdp. To avoid
performance impact this check is guarded by a static key, which is
incremented when a XDP program is loaded onto a bond device. This
approach was chosen to avoid changes to drivers implementing XDP. If
the slave device does not match the receive device, then XDP_REDIRECT
is transparently used to perform the redirection in order to have
the network driver release the packet from its RX ring. The bonding
driver hashing functions have been refactored to allow reuse with
xdp_buff's to avoid code duplication.
The motivation for this change is to enable use of bonding (and
802.3ad) in hairpinning L4 load-balancers such as [1] implemented with
XDP and also to transparently support bond devices for projects that
use XDP given most modern NICs have dual port adapters. An alternative
to this approach would be to implement 802.3ad in user-space and
implement the bonding load-balancing in the XDP program itself, but
is rather a cumbersome endeavor in terms of slave device management
(e.g. by watching netlink) and requires separate programs for native
vs bond cases for the orchestrator. A native in-kernel implementation
overcomes these issues and provides more flexibility.
Below are benchmark results done on two machines with 100Gbit
Intel E810 (ice) NIC and with 32-core 3970X on sending machine, and
16-core 3950X on receiving machine. 64 byte packets were sent with
pktgen-dpdk at full rate. Two issues [2, 3] were identified with the
ice driver, so the tests were performed with iommu=off and patch [2]
applied. Additionally the bonding round robin algorithm was modified
to use per-cpu tx counters as high CPU load (50% vs 10%) and high rate
of cache misses were caused by the shared rr_tx_counter (see patch
2/3). The statistics were collected using "sar -n dev -u 1 10". On top
of that, for ice, further work is in progress on improving the XDP_TX
numbers [4].
-----------------------| CPU |--| rxpck/s |--| txpck/s |----
without patch (1 dev):
XDP_DROP: 3.15% 48.6Mpps
XDP_TX: 3.12% 18.3Mpps 18.3Mpps
XDP_DROP (RSS): 9.47% 116.5Mpps
XDP_TX (RSS): 9.67% 25.3Mpps 24.2Mpps
-----------------------
with patch, bond (1 dev):
XDP_DROP: 3.14% 46.7Mpps
XDP_TX: 3.15% 13.9Mpps 13.9Mpps
XDP_DROP (RSS): 10.33% 117.2Mpps
XDP_TX (RSS): 10.64% 25.1Mpps 24.0Mpps
-----------------------
with patch, bond (2 devs):
XDP_DROP: 6.27% 92.7Mpps
XDP_TX: 6.26% 17.6Mpps 17.5Mpps
XDP_DROP (RSS): 11.38% 117.2Mpps
XDP_TX (RSS): 14.30% 28.7Mpps 27.4Mpps
--------------------------------------------------------------
RSS: Receive Side Scaling, e.g. the packets were sent to a range of
destination IPs.
[1]: https://cilium.io/blog/2021/05/20/cilium-110#standalonelb
[2]: https://lore.kernel.org/bpf/20210601113236.42651-1-maciej.fijalkowski@intel.com/T/#t
[3]: https://lore.kernel.org/bpf/CAHn8xckNXci+X_Eb2WMv4uVYjO2331UWB2JLtXr_58z0Av8+8A@mail.gmail.com/
[4]: https://lore.kernel.org/bpf/20210805230046.28715-1-maciej.fijalkowski@intel.com/T/#t
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20210731055738.16820-4-joamaki@gmail.com
|
|
Add an option lacp_active, which is similar with team's runner.active.
This option specifies whether to send LACPDU frames periodically. If set
on, the LACPDU frames are sent along with the configured lacp_rate
setting. If set off, the LACPDU frames acts as "speak when spoken to".
Note, the LACPDU state frames still will be sent when init or unbind port.
v2: remove module parameter
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bonding has been supporting ipsec offload.
When SA is added, bonding just passes SA to its own active real interface.
But it doesn't manage SA.
So, when events(add/del real interface, active real interface change, etc)
occur, bonding can't handle that well because It doesn't manage SA.
So some problems(panic, UAF, refcnt leak)occur.
In order to make it stable, it should manage SA.
That's the reason why struct bond_ipsec is added.
When a new SA is added to bonding interface, it is stored in the
bond_ipsec list. And the SA is passed to a current active real interface.
If events occur, it uses bond_ipsec data to handle these events.
bond->ipsec_list is protected by bond->ipsec_lock.
If a current active real interface is changed, the following logic works.
1. delete all SAs from old active real interface
2. Add all SAs to the new active real interface.
3. If a new active real interface doesn't support ipsec offload or SA's
option, it sets real_dev to NULL.
Fixes: 18cb261afd7b ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The round-robin rr_tx_counter was shared across CPUs leading to
significant cache thrashing at high packet rates. This patch switches
the round-robin packet counter to use a per-cpu variable to decide
the destination slave.
On a test with 2x100Gbit ICE nic with pktgen_sample_04_many_flows.sh
(-s 64 -t 32) the tx rate was 19.6Mpps before and 22.3Mpps after
this patch.
"perf top -e cache_misses" before:
12.31% [bonding] [k] bond_xmit_roundrobin_slave_get
10.59% [sch_fq_codel] [k] fq_codel_dequeue
9.34% [kernel] [k] skb_release_data
after:
15.42% [sch_fq_codel] [k] fq_codel_dequeue
10.06% [kernel] [k] __memset
9.12% [kernel] [k] skb_release_data
Signed-off-by: Jussi Maki <joamaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the description in previous patch (for TX):
As the bond interface is being bypassed by the TLS module, interacting
directly against the lower devs, there is no way for the bond interface
to disable its device offload capabilities, as long as the mode/policy
config allows it.
Hence, the feature flag is not directly controllable, but just reflects
the offload status based on the logic under bond_sk_check().
Here we just declare RX device offload support, and expose it via the
NETIF_F_HW_TLS_RX flag.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement TLS TX device offload for bonding interfaces.
This allows kTLS sockets running on a bond to benefit from the
device offload on capable lower devices.
To allow a simple and fast maintenance of the TLS context in SW and
lower devices, we bind the TLS socket to a specific lower dev.
To achieve a behavior similar to SW kTLS, we support only balance-xor
and 802.3ad modes, with xmit_hash_policy=layer3+4. This is enforced
in bond_sk_check(), done in a previous patch.
For the above configuration, the SW implementation keeps picking the
same exact lower dev for all the socket's SKBs. The device offload
behaves similarly, making the decision once at the connection creation.
Per socket, the TLS module should work directly with the lowest netdev
in chain, to call the tls_dev_ops operations.
As the bond interface is being bypassed by the TLS module, interacting
directly against the lower devs, there is no way for the bond interface
to disable its device offload capabilities, as long as the mode/policy
config allows it.
Hence, the feature flag is not directly controllable, but just reflects
the current offload status based on the logic under bond_sk_check().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ndo_sk_get_lower_dev() implementation for bond interfaces.
Support only for the cases where the socket's and SKBs' hash
yields identical value for the whole connection lifetime.
Here we restrict it to L3+4 sockets only, with
xmit_hash_policy==LAYER34 and bond modes xor/802.3ad.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Don't try to adjust XFRM support flags if the bond device isn't yet
registered. Bad things can currently happen when netdev_change_features()
is called without having wanted_features fully filled in yet. This code
runs both on post-module-load mode changes, as well as at module init
time, and when run at module init time, it is before register_netdevice()
has been called and filled in wanted_features. The empty wanted_features
led to features also getting emptied out, which was definitely not the
intended behavior, so prevent that from happening.
Originally, I'd hoped to stop adjusting wanted_features at all in the
bonding driver, as it's documented as being something only the network
core should touch, but we actually do need to do this to properly update
both the features and wanted_features fields when changing the bond type,
or we get to a situation where ethtool sees:
esp-hw-offload: off [requested on]
I do think we should be using netdev_update_features instead of
netdev_change_features here though, so we only send notifiers when the
features actually changed.
Fixes: a3b658cfb664 ("bonding: allow xfrm offload setup post-module-load")
Reported-by: Ivan Vecera <ivecera@redhat.com>
Suggested-by: Ivan Vecera <ivecera@redhat.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Link: https://lore.kernel.org/r/20201205172229.576587-1-jarod@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller found that with CONFIG_DEBUG_KOBJECT_RELEASE=y, releasing a
struct slave device could result in the following splat:
kobject: 'bonding_slave' (00000000cecdd4fe): kobject_release, parent 0000000074ceb2b2 (delayed 1000)
bond0 (unregistering): (slave bond_slave_1): Releasing backup interface
------------[ cut here ]------------
ODEBUG: free active (active state 0) object type: timer_list hint: workqueue_select_cpu_near kernel/workqueue.c:1549 [inline]
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x98 kernel/workqueue.c:1600
WARNING: CPU: 1 PID: 842 at lib/debugobjects.c:485 debug_print_object+0x180/0x240 lib/debugobjects.c:485
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 842 Comm: kworker/u4:4 Tainted: G S 5.9.0-rc8+ #96
Hardware name: linux,dummy-virt (DT)
Workqueue: netns cleanup_net
Call trace:
dump_backtrace+0x0/0x4d8 include/linux/bitmap.h:239
show_stack+0x34/0x48 arch/arm64/kernel/traps.c:142
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x174/0x1f8 lib/dump_stack.c:118
panic+0x360/0x7a0 kernel/panic.c:231
__warn+0x244/0x2ec kernel/panic.c:600
report_bug+0x240/0x398 lib/bug.c:198
bug_handler+0x50/0xc0 arch/arm64/kernel/traps.c:974
call_break_hook+0x160/0x1d8 arch/arm64/kernel/debug-monitors.c:322
brk_handler+0x30/0xc0 arch/arm64/kernel/debug-monitors.c:329
do_debug_exception+0x184/0x340 arch/arm64/mm/fault.c:864
el1_dbg+0x48/0xb0 arch/arm64/kernel/entry-common.c:65
el1_sync_handler+0x170/0x1c8 arch/arm64/kernel/entry-common.c:93
el1_sync+0x80/0x100 arch/arm64/kernel/entry.S:594
debug_print_object+0x180/0x240 lib/debugobjects.c:485
__debug_check_no_obj_freed lib/debugobjects.c:967 [inline]
debug_check_no_obj_freed+0x200/0x430 lib/debugobjects.c:998
slab_free_hook mm/slub.c:1536 [inline]
slab_free_freelist_hook+0x190/0x210 mm/slub.c:1577
slab_free mm/slub.c:3138 [inline]
kfree+0x13c/0x460 mm/slub.c:4119
bond_free_slave+0x8c/0xf8 drivers/net/bonding/bond_main.c:1492
__bond_release_one+0xe0c/0xec8 drivers/net/bonding/bond_main.c:2190
bond_slave_ne |
