| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Implements the USB part of Intel USB-I2C/GPIO/SPI adapter device
named "La Jolla Cove Adapter" (LJCA).
The communication between the various LJCA module drivers and the
hardware will be muxed/demuxed by this driver. Three modules (
I2C, GPIO, and SPI) are supported currently.
Each sub-module of LJCA device is identified by type field within
the LJCA message header.
The sub-modules of LJCA can use ljca_transfer() to issue a transfer
between host and hardware. And ljca_register_event_cb is exported
to LJCA sub-module drivers for hardware event subscription.
The minimum code in ASL that covers this board is
Scope (\_SB.PCI0.DWC3.RHUB.HS01)
{
Device (GPIO)
{
Name (_ADR, Zero)
Name (_STA, 0x0F)
}
Device (I2C)
{
Name (_ADR, One)
Name (_STA, 0x0F)
}
Device (SPI)
{
Name (_ADR, 0x02)
Name (_STA, 0x0F)
}
}
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/1696833205-16716-2-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_buffer_map_sg() and usb_buffer_unmap_sg() have no definition
since the beginning of v5.4. The rest are gone from 2.6.12.
Signed-off-by: Randy Li <ayaka@soulik.info>
Link: https://lore.kernel.org/r/20230914172336.18761-2-ayaka@soulik.info
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB_GADGET_DELAYED_STATUS was introduced in commit 1b9ba000177e ("usb:
gadget: composite: Allow function drivers to pause control transfers").
It was initially intended for the composite framework to allow delaying
completing the status stage of a SET_CONFIGURATION request until all
functions are ready.
Unfortunately, that commit had an unintended side-effect of returning
USB_GADGET_DELAYED_STATUS from the ->setup() call of the composite
framework gadget driver.
As a result of this and the incomplete documentation, some UDC drivers
started relying on USB_GADGET_DELAYED_STATUS to decide when to avoid
autocompleting the status stage for 0-length control transfers. dwc3 was
the first in commit 5bdb1dcc6330 ("usb: dwc3: ep0: handle delayed_status
again"). And a number of other UDC drivers followed later, probably
relying on the dwc3 behavior as a reference.
Unfortunately, this violated the interface between the UDC and the
gadget driver for 0-length control transfers: the UDC driver must only
proceed with the status stage for a 0-length control transfer once the
gadget driver queued a response to EP0.
As a result, a few gadget drivers are partially broken when used with
a UDC that only delays the status stage for 0-length transfers when
USB_GADGET_DELAYED_STATUS is returned from the setup() callback.
This includes Raw Gadget and GadgetFS. For FunctionFS, a workaround was
added in commit 946ef68ad4e4 ("usb: gadget: ffs: Let setup() return
USB_GADGET_DELAYED_STATUS") and commit 4d644abf2569 ("usb: gadget: f_fs:
Only return delayed status when len is 0").
The proper solution to this issue would be to contain
USB_GADGET_DELAYED_STATUS within the composite framework and make all
UDC drivers to not complete the status stage for 0-length requests on
their own.
Unfortunately, there is quite a few UDC drivers that need to get fixed
and the required changes for some of them are not trivial.
For now, update the comments to clarify that USB_GADGET_DELAYED_STATUS
must not be used by the UDC drivers.
The following two commits also add workarounds to Raw Gadget and GadgetFS
to make them compatible with the broken UDC drivers until they are fixed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/7f0ee06c68c7241c844cd50f8565fdd5ead79b1b.1693237258.git.andreyknvl@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exposing the value of the field as is.
The Peak Current value has to be interpreted as described
in Table 6-10 (Fixed Power Source Peak Current Capability)
of the USB Power Delivery Specification, but that
interpretation will be done in user space, not in kernel.
Suggested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231002142240.2641962-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. In the pci-quirks case the I/O port acceses are
used in the quirks for several AMD south bridges, Add a config option
for the AMD quirks to depend on HAS_IOPORT and #ifdef the quirk code.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230911125653.1393895-3-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added a helper macro to get the Type C cable speed when provided the
cable VDO.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20230920023243.2494410-4-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per USB Type-C Connector specification v2.2 section F.2.6, BIT25
represents Active or Passive cable. Added BIT25 defination to the
Thunderbolt 3 cable discover mode VDO.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20230920023243.2494410-3-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Displayport Alternate mode 2.1 requires configuration for additional
cable details such as signalling for cable, UHBR13.5 Support, Cable type
and DPAM version.
These details can be used with mux drivers to configure SOP DP
configuration for Displayport Alternate mode 2.1.
This change also includes pertinent cable signalling support in displayport
alternate mode.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20230920023243.2494410-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a SPDX entry, so we can remove the boilerplate.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230922064551.4663-1-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix the module compression with xz so the in-kernel decompressor
works
- Document a kconfig idiom to express an optional dependency between
modules
- Make modpost, when W=1 is given, detect broken drivers that reference
.exit.* sections
- Remove unused code
* tag 'kbuild-fixes-v6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: remove stale code for 'source' symlink in packaging scripts
modpost: Don't let "driver"s reference .exit.*
vmlinux.lds.h: remove unused CPU_KEEP and CPU_DISCARD macros
modpost: add missing else to the "of" check
Documentation: kbuild: explain handling optional dependencies
kbuild: Use CRC32 and a 1MiB dictionary for XZ compressed modules
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Fourteen hotfixes, eleven of which are cc:stable. The remainder
pertain to issues which were introduced after 6.5"
* tag 'mm-hotfixes-stable-2023-10-01-08-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
Crash: add lock to serialize crash hotplug handling
selftests/mm: fix awk usage in charge_reserved_hugetlb.sh and hugetlb_reparenting_test.sh that may cause error
mm: mempolicy: keep VMA walk if both MPOL_MF_STRICT and MPOL_MF_MOVE are specified
mm/damon/vaddr-test: fix memory leak in damon_do_test_apply_three_regions()
mm, memcg: reconsider kmem.limit_in_bytes deprecation
mm: zswap: fix potential memory corruption on duplicate store
arm64: hugetlb: fix set_huge_pte_at() to work with all swap entries
mm: hugetlb: add huge page size param to set_huge_pte_at()
maple_tree: add MAS_UNDERFLOW and MAS_OVERFLOW states
maple_tree: add mas_is_active() to detect in-tree walks
nilfs2: fix potential use after free in nilfs_gccache_submit_read_data()
mm: abstract moving to the next PFN
mm: report success more often from filemap_map_folio_range()
fs: binfmt_elf_efpic: fix personality for ELF-FDPIC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"Fix a spurious kernel warning during CPU hotplug events that may
trigger when timer/hrtimer softirqs are pending, which are otherwise
hotplug-safe and don't merit a warning"
* tag 'timers-urgent-2023-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Tag (hr)timer softirq as hotplug safe
|
|
Remove the left-over of commit e24f6628811e ("modpost: remove all
traces of cpuinit/cpuexit sections").
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- fix the narea calculation in swiotlb initialization (Ross Lagerwall)
- fix the check whether a device has used swiotlb (Petr Tesarik)
* tag 'dma-mapping-6.6-2023-09-30' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix the check whether a device has used software IO TLB
swiotlb: use the calculated number of areas
|
|
Patch series "Fix set_huge_pte_at() panic on arm64", v2.
This series fixes a bug in arm64's implementation of set_huge_pte_at(),
which can result in an unprivileged user causing a kernel panic. The
problem was triggered when running the new uffd poison mm selftest for
HUGETLB memory. This test (and the uffd poison feature) was merged for
v6.5-rc7.
Ideally, I'd like to get this fix in for v6.6 and I've cc'ed stable
(correctly this time) to get it backported to v6.5, where the issue first
showed up.
Description of Bug
==================
arm64's huge pte implementation supports multiple huge page sizes, some of
which are implemented in the page table with multiple contiguous entries.
So set_huge_pte_at() needs to work out how big the logical pte is, so that
it can also work out how many physical ptes (or pmds) need to be written.
It previously did this by grabbing the folio out of the pte and querying
its size.
However, there are cases when the pte being set is actually a swap entry.
But this also used to work fine, because for huge ptes, we only ever saw
migration entries and hwpoison entries. And both of these types of swap
entries have a PFN embedded, so the code would grab that and everything
still worked out.
But over time, more calls to set_huge_pte_at() have been added that set
swap entry types that do not embed a PFN. And this causes the code to go
bang. The triggering case is for the uffd poison test, commit
99aa77215ad0 ("selftests/mm: add uffd unit test for UFFDIO_POISON"), which
causes a PTE_MARKER_POISONED swap entry to be set, coutesey of commit
8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs") -
added in v6.5-rc7. Although review shows that there are other call sites
that set PTE_MARKER_UFFD_WP (which also has no PFN), these don't trigger
on arm64 because arm64 doesn't support UFFD WP.
If CONFIG_DEBUG_VM is enabled, we do at least get a BUG(), but otherwise,
it will dereference a bad pointer in page_folio():
static inline struct folio *hugetlb_swap_entry_to_folio(swp_entry_t entry)
{
VM_BUG_ON(!is_migration_entry(entry) && !is_hwpoison_entry(entry));
return page_folio(pfn_to_page(swp_offset_pfn(entry)));
}
Fix
===
The simplest fix would have been to revert the dodgy cleanup commit
18f3962953e4 ("mm: hugetlb: kill set_huge_swap_pte_at()"), but since
things have moved on, this would have required an audit of all the new
set_huge_pte_at() call sites to see if they should be converted to
set_huge_swap_pte_at(). As per the original intent of the change, it
would also leave us open to future bugs when people invariably get it
wrong and call the wrong helper.
So instead, I've added a huge page size parameter to set_huge_pte_at().
This means that the arm64 code has the size in all cases. It's a bigger
change, due to needing to touch the arches that implement the function,
but it is entirely mechanical, so in my view, low risk.
I've compile-tested all touched arches; arm64, parisc, powerpc, riscv,
s390, sparc (and additionally x86_64). I've additionally booted and run
mm selftests against arm64, where I observe the uffd poison test is fixed,
and there are no other regressions.
This patch (of 2):
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the pte is being set in set_huge_pte_at(). Provide for this by
adding an `unsigned long sz` parameter to the function. This follows the
same pattern as huge_pte_clear().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, parisc, powerpc,
riscv, s390, sparc). The actual arm64 bug will be fixed in a separate
commit.
No behavioral changes intended.
Link: https://lkml.kernel.org/r/20230922115804.2043771-1-ryan.roberts@arm.com
Link: https://lkml.kernel.org/r/20230922115804.2043771-2-ryan.roberts@arm.com
Fixes: 8a13897fb0da ("mm: userfaultfd: support UFFDIO_POISON for hugetlbfs")
Signed-off-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> [powerpc 8xx]
Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com> [vmalloc change]
Cc: Alexandre Ghiti <alex@ghiti.fr>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Muchun Song <muchun.song@linux.dev>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Qi Zheng <zhengqi.arch@bytedance.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org> [6.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
When updating the maple tree iterator to avoid rewalks, an issue was
introduced when shifting beyond the limits. This can be seen by trying to
go to the previous address of 0, which would set the maple node to
MAS_NONE and keep the range as the last entry.
Subsequent calls to mas_find() would then search upwards from mas->last
and skip the value at mas->index/mas->last. This showed up as a bug in
mprotect which skips the actual VMA at the current range after attempting
to go to the previous VMA from 0.
Since MAS_NONE may already be set when searching for a value that isn't
contained within a node, changing the handling of MAS_NONE in mas_find()
would make the code more complicated and error prone. Furthermore, there
was no way to tell which limit was hit, and thus which action to take
(next or the entry at the current range).
This solution is to add two states to track what happened with the
previous iterator action. This allows for the expected behaviour of the
next command to return the correct item (either the item at the range
requested, or the next/previous).
Tests are also added and updated accordingly.
Link: https://lkml.kernel.org/r/20230921181236.509072-3-Liam.Howlett@oracle.com
Link: https://gist.github.com/heatd/85d2971fae1501b55b6ea401fbbe485b
Link: https://lore.kernel.org/linux-mm/20230921181236.509072-1-Liam.Howlett@oracle.com/
Fixes: 39193685d585 ("maple_tree: try harder to keep active node with mas_prev()")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Reported-by: Pedro Falcato <pedro.falcato@gmail.com>
Closes: https://gist.github.com/heatd/85d2971fae1501b55b6ea401fbbe485b
Closes: https://bugs.archlinux.org/task/79656
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "maple_tree: Fix mas_prev() state regression".
Pedro Falcato retported an mprotect regression [1] which was bisected back
to the iterator changes for maple tree. Root cause analysis showed the
mas_prev() running off the end of the VMA space (previous from 0) followed
by mas_find(), would skip the first value.
This patchset introduces maple state underflow/overflow so the sequence of
calls on the maple state will return what the user expects.
Users who encounter this bug may see mprotect(), userfaultfd_register(),
and mlock() fail on VMAs mapped with address 0.
This patch (of 2):
Instead of constantly checking each possibility of the maple state,
create a fast path that will skip over checking unlikely states.
Link: https://lkml.kernel.org/r/20230921181236.509072-1-Liam.Howlett@oracle.com
Link: https://lkml.kernel.org/r/20230921181236.509072-2-Liam.Howlett@oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Pedro Falcato <pedro.falcato@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
In order to fix the L1TF vulnerability, x86 can invert the PTE bits for
PROT_NONE VMAs, which means we cannot move from one PTE to the next by
adding 1 to the PFN field of the PTE. This results in the BUG reported at
[1].
Abstract advancing the PTE to the next PFN through a pte_next_pfn()
function/macro.
Link: https://lkml.kernel.org/r/20230920040958.866520-1-willy@infradead.org
Fixes: bcc6cc832573 ("mm: add default definition of set_ptes()")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reported-by: syzbot+55cc72f8cc3a549119df@syzkaller.appspotmail.com
Closes: https://lkml.kernel.org/r/000000000000d099fa0604f03351@google.com [1]
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Pull ceph fixes from Ilya Dryomov:
"A series that fixes an involved 'double watch error' deadlock in RBD
marked for stable and two cleanups"
* tag 'ceph-for-6.6-rc4' of https://github.com/ceph/ceph-client:
rbd: take header_rwsem in rbd_dev_refresh() only when updating
rbd: decouple parent info read-in from updating rbd_dev
rbd: decouple header read-in from updating rbd_dev->header
rbd: move rbd_dev_refresh() definition
Revert "ceph: make members in struct ceph_mds_request_args_ext a union"
ceph: remove unnecessary check for NULL in parse_longname()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ATA fixes from Damien Le Moal:
"A larger than usual set of fixes for 6.6-rc4 due to the unexpected
number of fixes needed to address ATA disks suspend/resume issues.
In more detail:
- Add missing additionalProperties on child nodes to the pata-common
DT bindings (Rob)
- Fix handling of the REPORT SUPPORTED OPERATION CODES command to
ignore reserved bits (Niklas)
- Increase port multiplier soft reset timeout to accomodate slow
devices and avoid issues on wakeup (Matthias)
- A couple of minor code fixes to avoid compilation warnings in
libata-core and libata-eh (me)
- Many patches from me to address suspend/resume issues, and in
particular a potential deadlock on resume due to the SCSI disk
driver resume operation not being synchronized with libata EH port
resume handling.
This is addressed by changing the scsi disk driver disk start/stop
control to allow libata to execute disk suspend (spin down) and
resume (spin up) on its own during system suspend/resume. Runtime
suspend/resume control remains with the SCSI disk driver.
Other fixes include:
- Fix libata power management request issuing to avoid races
- Establish a link between ATA ports and SCSI devices to order PM
operations
- Fix device removal to avoid issues with driver rmmod removal
- Fix synchronization of libata device rescan and SCSI disk resume
operation
- Remove libsas PM operations as suspend/resume is handled
directly by the sas controller resume
- Fix the SCSI disk driver to not issue commands to suspended
disks, thus avoiding potential system lock-up on resume"
* tag 'ata-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-eh: Fix compilation warning in ata_eh_link_report()
ata: libata-core: Fix compilation warning in ata_dev_config_ncq()
scsi: sd: Do not issue commands to suspended disks on shutdown
ata: libata-core: Do not register PM operations for SAS ports
ata: libata-scsi: Fix delayed scsi_rescan_device() execution
scsi: Do not attempt to rescan suspended devices
ata: libata-scsi: Disable scsi device manage_system_start_stop
scsi: sd: Differentiate system and runtime start/stop management
ata: libata-scsi: link ata port and scsi device
ata: libata-core: Fix port and device removal
ata: libata-core: Fix ata_port_request_pm() locking
ata: libata-sata: increase PMP SRST timeout to 10s
ata: libata-scsi: ignore reserved bits for REPORT SUPPORTED OPERATION CODES
dt-bindings: ata: pata-common: Add missing additionalProperties on child nodes
|
|
scsi_rescan_device() takes a scsi device lock before executing a device
handler and device driver rescan methods. Waiting for the completion of
any command issued to the device by these methods will thus be done with
the device lock held. As a result, there is a risk of deadlocking within
the power management code if scsi_rescan_device() is called to handle a
device resume with the associated scsi device not yet resumed.
Avoid such situation by checking that the target scsi device is in the
running state, that is, fully capable of executing commands, before
proceeding with the rescan and bailout returning -EWOULDBLOCK otherwise.
With this error return, the caller can retry rescaning the device after
a delay.
The state check is done with the device lock held and is thus safe
against incoming suspend power management operations.
Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
|
|
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A single fix for libata: older devices don't support command duration
limits (CDL) and some don't support report opcodes, meaning there's no
way to tell if they support the command or not.
Reduce the problems of incorrectly using CDL commands on older devices
by checking SCSI spec compliance at SPC-5 (the spec which introduced
the command) before turning on CDL"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: ata: Do no try to probe for CDL on old drives
|
|
Specific stress involving frequent CPU-hotplug operations, such as
running rcutorture for example, may trigger the following message:
NOHZ tick-stop error: local softirq work is pending, handler #02!!!"
This happens in the CPU-down hotplug process, after
CPUHP_AP_SMPBOOT_THREADS whose teardown callback parks ksoftirqd, and
before the target CPU shuts down through CPUHP_AP_IDLE_DEAD. In this
fragile intermediate state, softirqs waiting for threaded handling may be
forever ignored and eventually reported by the idle task as in the above
example.
However some vectors are known to be safe as long as the corresponding
subsystems have teardown callbacks handling the migration of their
events. The above error message reports pending timers softirq although
this vector can be considered as hotplug safe because the
CPUHP_TIMERS_PREPARE teardown callback performs the necessary migration
of timers after the death of the CPU. Hrtimers also have a similar
hotplug handling.
Therefore this error message, as far as (hr-)timers are concerned, can
be considered spurious and the relevant softirq vectors can be marked as
hotplug safe.
Fixes: 0345691b24c0 ("tick/rcu: Stop allowing RCU_SOFTIRQ in idle")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230912104406.312185-6-frederic@kernel.org
|
|
When CONFIG_SWIOTLB_DYNAMIC=y, devices which do not use the software IO TLB
can avoid swiotlb lookup. A flag is added by commit 1395706a1490 ("swiotlb:
search the software IO TLB only if the device makes use of it"), the flag
is correctly set, but it is then never checked. Add the actual check here.
Note that this code is an alternative to the default pool check, not an
additional check, because:
1. swiotlb_find_pool() also searches the default pool;
2. if dma_uses_io_tlb is false, the default swiotlb pool is not used.
Tested in a KVM guest against a QEMU RAM-backed SATA disk over virtio and
*not* using software IO TLB, this patch increases IOPS by approx 2% for
4-way parallel I/O.
The write memory barrier in swiotlb_dyn_alloc() is not needed, because a
newly allocated pool must always be observed by swiotlb_find_slots() before
an address from that pool is passed to is_swiotlb_buffer().
Correctness was verified using the following litmus test:
C swiotlb-new-pool
(*
* Result: Never
*
* Check that a newly allocated pool is always visible when the
* corresponding swiotlb buffer is visible.
*)
{
mem_pools = default;
}
P0(int **mem_pools, int *pool)
{
/* add_mem_pool() */
WRITE_ONCE(*pool, 999);
rcu_assign_pointer(*mem_pools, pool);
}
P1(int **mem_pools, int *flag, int *buf)
{
/* swiotlb_find_slots() */
int *r0;
int r1;
rcu_read_lock();
r0 = READ_ONCE(*mem_pools);
r1 = READ_ONCE(*r0);
rcu_read_unlock();
if (r1) {
WRITE_ONCE(*flag, 1);
smp_mb();
}
/* device driver (presumed) */
WRITE_ONCE(*buf, r1);
}
P2(int **mem_pools, int *flag, int *buf)
{
/* device driver (presumed) */
int r0 = READ_ONCE(*buf);
/* is_swiotlb_buffer() */
int r1;
int *r2;
int r3;
smp_rmb();
r1 = READ_ONCE(*flag);
if (r1) {
/* swiotlb_find_pool() */
rcu_read_lock();
r2 = READ_ONCE(*mem_pools);
r3 = READ_ONCE(*r2);
rcu_read_unlock();
}
}
exists (2:r0<>0 /\ 2:r3=0) (* Not found. *)
Fixes: 1395706a1490 ("swiotlb: search the software IO TLB only if the device makes use of it")
Reported-by: Jonathan Corbet <corbet@lwn.net>
Closes: https://lore.kernel.org/linux-iommu/87a5uz3ob8.fsf@meer.lwn.net/
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d52a ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix EL2 Stage-1 MMIO mappings where a random address was used
- Fix SMCCC function number comparison when the SVE hint is set
RISC-V:
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
x86:
- Fixes for TSC_AUX virtualization
- Stop zapping page tables asynchronously, since we don't zap them as
often as before"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Do not use user return MSR support for virtualized TSC_AUX
KVM: SVM: Fix TSC_AUX virtualization setup
KVM: SVM: INTERCEPT_RDTSCP is never intercepted anyway
KVM: x86/mmu: Stop zapping invalidated TDP MMU roots asynchronously
KVM: x86/mmu: Do not filter address spaces in for_each_tdp_mmu_root_yield_safe()
KVM: x86/mmu: Open code leaf invalidation from mmu_notifier
KVM: riscv: selftests: Selectively filter-out AIA registers
KVM: riscv: selftests: Fix ISA_EXT register handling in get-reg-list
RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensions
RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registers
KVM: selftests: Assert that vasprintf() is successful
KVM: arm64: nvhe: Ignore SVE hint in SMCCC function ID
KVM: arm64: Properly return allocated EL2 VA from hyp_alloc_private_va_range()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of regression fixes, bug fixes, and some small cleanups
to the Compute Express Link code.
The regressions arrived in the v6.5 dev cycle and missed the v6.6
merge window due to my personal absences this cycle. The most
important fixes are for scenarios where the CXL subsystem fails to
parse valid region configurations established by platform firmware.
This is important because agreement between OS and BIOS on the CXL
configuration is fundamental to implementing "OS native" error
handling, i.e. address translation and component failure
identification.
Other important fixes are a driver load error when the BIOS lets the
Linux PCI core handle AER events, but not CXL memory errors.
The other fixex might have end user impact, but for now are only known
to trigger in our test/emulation environment.
Summary:
- Fix multiple scenarios where platform firmware defined regions fail
to be assembled by the CXL core.
- Fix a spurious driver-load failure on platforms that enable OS
native AER, but not OS native CXL error handling.
- Fix a regression detecting "poison" commands when "security"
commands are also defined.
- Fix a cxl_test regression with the move to centralize CXL port
register enumeration in the CXL core.
- Miscellaneous small fixes and cleanups"
* tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Annotate struct cxl_cxims_data with __counted_by
cxl/port: Fix cxl_test register enumeration regression
cxl/region: Refactor granularity select in cxl_port_setup_targets()
cxl/region: Match auto-discovered region decoders by HPA range
cxl/mbox: Fix CEL logic for poison and security commands
cxl/pci: Replace host_bridge->native_aer with pcie_aer_is_native()
PCI/AER: Export pcie_aer_is_native()
cxl/pci: Fix appropriate checking for _OSC while handling CXL RAS registers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"13 hotfixes, 10 of which pertain to post-6.5 issues. The other three
are cc:stable"
* tag 'mm-hotfixes-stable-2023-09-23-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
proc: nommu: fix empty /proc/<pid>/maps
filemap: add filemap_map_order0_folio() to handle order0 folio
proc: nommu: /proc/<pid>/maps: release mmap read lock
mm: memcontrol: fix GFP_NOFS recursion in memory.high enforcement
pidfd: prevent a kernel-doc warning
argv_split: fix kernel-doc warnings
scatterlist: add missing function params to kernel-doc
selftests/proc: fixup proc-empty-vm test after KSM changes
revert "scripts/gdb/symbols: add specific ko module load command"
selftests: link libasan statically for tests with -fsanitize=address
task_work: add kerneldoc annotation for 'data' argument
mm: page_alloc: fix CMA and HIGHATOMIC landing on the wrong buddy list
sh: mm: re-add lost __ref to ioremap_prot() to fix modpost warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix lockdep, fix a boot failure, fix some build warnings, fix document
links, and some cleanups"
* tag 'loongarch-fixes-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
docs/zh_CN/LoongArch: Update the links of ABI
docs/LoongArch: Update the links of ABI
LoongArch: Don't inline kasan_mem_to_shadow()/kasan_shadow_to_mem()
kasan: Cleanup the __HAVE_ARCH_SHADOW_MAP usage
LoongArch: Set all reserved memblocks on Node#0 at initialization
LoongArch: Remove dead code in relocate_new_kernel
LoongArch: Use _UL() and _ULL()
LoongArch: Fix some build warnings with W=1
LoongArch: Fix lockdep static memory detection
|
|
HEAD
KVM/riscv fixes for 6.6, take #1
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Fix UAPI stddef.h to avoid C++-ism (Alexey Dobriyan)
- Fix harmless UAPI stddef.h header guard endif (Alexey Dobriyan)
* tag 'hardening-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
uapi: stddef.h: Fix __DECLARE_FLEX_ARRAY for C++
uapi: stddef.h: Fix header guard location
|
|
Pull xfs fixes from Chandan Babu:
- Fix an integer overflow bug when processing an fsmap call
- Fix crash due to CPU hot remove event racing with filesystem mount
operation
- During read-only mount, XFS does not allow the contents of the log to
be recovered when there are one or more unrecognized rcompat features
in the primary superblock, since the log might have intent items
which the kernel does not know how to process
- During recovery of log intent items, XFS now reserves log space
sufficient for one cycle of a permanent transaction to execute.
Otherwise, this could lead to livelocks due to non-availability of
log space
- On an fs which has an ondisk unlinked inode list, trying to delete a
file or allocating an O_TMPFILE file can cause the fs to the shutdown
if the first inode in the ondisk inode list is not present in the
inode cache. The bug is solved by explicitly loading the first inode
in the ondisk unlinked inode list into the inode cache if it is not
already cached
A similar problem arises when the uncached inode is present in the
middle of the ondisk unlinked inode list. This second bug is
triggered when executing operations like quotacheck and bulkstat. In
this case, XFS now reads in the entire ondisk unlinked inode list
- Enable LARP mode only on recent v5 filesystems
- Fix a out of bounds memory access in scrub
- Fix a performance bug when locating the tail of the log during
mounting a filesystem
* tag 'xfs-6.6-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use roundup_pow_of_two instead of ffs during xlog_find_tail
xfs: only call xchk_stats_merge after validating scrub inputs
xfs: require a relatively recent V5 filesystem for LARP mode
xfs: make inode unlinked bucket re |
