From 3abee4579484c554961bb0af92a77adc0ebd791d Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:29 +0200 Subject: mfd: Add simple regmap based I2C driver There are I2C devices which contain several different functions but doesn't require any special access functions. For these kind of drivers an I2C regmap should be enough. Create an I2C driver which creates an I2C regmap and enumerates its children. If a device wants to use this as its MFD core driver, it has to add an individual compatible string. It may provide its own regmap configuration. Subdevices can use dev_get_regmap() on the parent to get their regmap instance. Signed-off-by: Michael Walle Signed-off-by: Lee Jones --- drivers/mfd/Kconfig | 12 ++++++++++ drivers/mfd/Makefile | 1 + drivers/mfd/simple-mfd-i2c.c | 56 ++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 69 insertions(+) create mode 100644 drivers/mfd/simple-mfd-i2c.c diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 33df0837ab41..6e1a38944d28 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -1162,6 +1162,18 @@ config MFD_SI476X_CORE To compile this driver as a module, choose M here: the module will be called si476x-core. +config MFD_SIMPLE_MFD_I2C + tristate + depends on I2C + select REGMAP_I2C + help + This driver creates a single register map with the intention for it + to be shared by all sub-devices. + + Once the register map has been successfully initialised, any + sub-devices represented by child nodes in Device Tree will be + subsequently registered. + config MFD_SM501 tristate "Silicon Motion SM501" depends on HAS_DMA diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index a60e5f835283..78d24a3e7c9e 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -264,3 +264,4 @@ obj-$(CONFIG_MFD_STMFX) += stmfx.o obj-$(CONFIG_MFD_KHADAS_MCU) += khadas-mcu.o obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o +obj-$(CONFIG_MFD_SIMPLE_MFD_I2C) += simple-mfd-i2c.o diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c new file mode 100644 index 000000000000..28e96a246be1 --- /dev/null +++ b/drivers/mfd/simple-mfd-i2c.c @@ -0,0 +1,56 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Simple MFD - I2C + * + * This driver creates a single register map with the intention for it to be + * shared by all sub-devices. Children can use their parent's device structure + * (dev.parent) in order to reference it. + * + * Once the register map has been successfully initialised, any sub-devices + * represented by child nodes in Device Tree will be subsequently registered. + */ + +#include +#include +#include +#include +#include + +static const struct regmap_config simple_regmap_config = { + .reg_bits = 8, + .val_bits = 8, +}; + +static int simple_mfd_i2c_probe(struct i2c_client *i2c) +{ + const struct regmap_config *config; + struct regmap *regmap; + + config = device_get_match_data(&i2c->dev); + if (!config) + config = &simple_regmap_config; + + regmap = devm_regmap_init_i2c(i2c, config); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return devm_of_platform_populate(&i2c->dev); +} + +static const struct of_device_id simple_mfd_i2c_of_match[] = { + {} +}; +MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match); + +static struct i2c_driver simple_mfd_i2c_driver = { + .probe_new = simple_mfd_i2c_probe, + .driver = { + .name = "simple-mfd-i2c", + .of_match_table = simple_mfd_i2c_of_match, + }, +}; +module_i2c_driver(simple_mfd_i2c_driver); + +MODULE_AUTHOR("Michael Walle "); +MODULE_DESCRIPTION("Simple MFD - I2C driver"); +MODULE_LICENSE("GPL v2"); -- cgit v1.2.3 From 48e28a249e3bcc31e6a2d27267410a6f5a03e39e Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:30 +0200 Subject: dt-bindings: mfd: Add bindings for sl28cpld Add a device tree bindings for the board management controller found on the Kontron SMARC-sAL28 board. Signed-off-by: Michael Walle Reviewed-by: Rob Herring Signed-off-by: Lee Jones --- .../bindings/gpio/kontron,sl28cpld-gpio.yaml | 54 ++++++++ .../bindings/hwmon/kontron,sl28cpld-hwmon.yaml | 27 ++++ .../kontron,sl28cpld-intc.yaml | 54 ++++++++ .../devicetree/bindings/mfd/kontron,sl28cpld.yaml | 153 +++++++++++++++++++++ .../bindings/pwm/kontron,sl28cpld-pwm.yaml | 35 +++++ .../bindings/watchdog/kontron,sl28cpld-wdt.yaml | 35 +++++ 6 files changed, 358 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml create mode 100644 Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml create mode 100644 Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml create mode 100644 Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml create mode 100644 Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml create mode 100644 Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml diff --git a/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml new file mode 100644 index 000000000000..e2d2c10e536a --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/kontron,sl28cpld-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + + There are three flavors of the GPIO controller, one full featured + input/output with interrupt support (kontron,sl28cpld-gpio), one + output-only (kontron,sl28-gpo) and one input-only (kontron,sl28-gpi). + + Each controller supports 8 GPIO lines. + +properties: + compatible: + enum: + - kontron,sl28cpld-gpio + - kontron,sl28cpld-gpi + - kontron,sl28cpld-gpo + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-line-names: + minItems: 1 + maxItems: 8 + +required: + - compatible + - "#gpio-cells" + - gpio-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml b/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml new file mode 100644 index 000000000000..010333cb25c0 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/kontron,sl28cpld-hwmon.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hardware monitoring driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + +properties: + compatible: + enum: + - kontron,sl28cpld-fan + + reg: + maxItems: 1 + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml b/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml new file mode 100644 index 000000000000..e8dfa6507f64 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/kontron,sl28cpld-intc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Interrupt controller driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + + The following interrupts are available. All types and levels are fixed + and handled by the board management controller. + + ==== ============= ================================== + IRQ line/device description + ==== ============= ================================== + 0 RTC_INT# Interrupt line from on-board RTC + 1 SMB_ALERT# Event on SMB_ALERT# line (P1) + 2 ESPI_ALERT0# Event on ESPI_ALERT0# line (S43) + 3 ESPI_ALERT1# Event on ESPI_ALERT1# line (S44) + 4 PWR_BTN# Event on PWR_BTN# line (P128) + 5 SLEEP# Event on SLEEP# line (S149) + 6 watchdog Interrupt of the internal watchdog + 7 n/a not used + ==== ============= ================================== + +properties: + compatible: + enum: + - kontron,sl28cpld-intc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + +required: + - compatible + - interrupts + - "#interrupt-cells" + - interrupt-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml new file mode 100644 index 000000000000..eb3b43547cb6 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/kontron,sl28cpld.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Kontron's sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + The board management controller may contain different IP blocks like + watchdog, fan monitoring, PWM controller, interrupt controller and a + GPIO controller. + +properties: + compatible: + const: kontron,sl28cpld + + reg: + description: + I2C device address. + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + +patternProperties: + "^gpio(@[0-9a-f]+)?$": + $ref: ../gpio/kontron,sl28cpld-gpio.yaml + + "^hwmon(@[0-9a-f]+)?$": + $ref: ../hwmon/kontron,sl28cpld-hwmon.yaml + + "^interrupt-controller(@[0-9a-f]+)?$": + $ref: ../interrupt-controller/kontron,sl28cpld-intc.yaml + + "^pwm(@[0-9a-f]+)?$": + $ref: ../pwm/kontron,sl28cpld-pwm.yaml + + "^watchdog(@[0-9a-f]+)?$": + $ref: ../watchdog/kontron,sl28cpld-wdt.yaml + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sl28cpld@4a { + compatible = "kontron,sl28cpld"; + reg = <0x4a>; + #address-cells = <1>; + #size-cells = <0>; + + watchdog@4 { + compatible = "kontron,sl28cpld-wdt"; + reg = <0x4>; + kontron,assert-wdt-timeout-pin; + }; + + hwmon@b { + compatible = "kontron,sl28cpld-fan"; + reg = <0xb>; + }; + + pwm@c { + compatible = "kontron,sl28cpld-pwm"; + reg = <0xc>; + #pwm-cells = <2>; + }; + + pwm@e { + compatible = "kontron,sl28cpld-pwm"; + reg = <0xe>; + #pwm-cells = <2>; + }; + + gpio@10 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x10>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "a", "b", "c"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@15 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x15>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@1a { + compatible = "kontron,sl28cpld-gpo"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@1b { + compatible = "kontron,sl28cpld-gpi"; + reg = <0x1b>; + + gpio-controller; + #gpio-cells = <2>; + }; + + interrupt-controller@1c { + compatible = "kontron,sl28cpld-intc"; + reg = <0x1c>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml b/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml new file mode 100644 index 000000000000..981cfec53f37 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/kontron,sl28cpld-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PWM driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + + The controller supports one PWM channel and supports only four distinct + frequencies (250Hz, 500Hz, 1kHz, 2kHz). + +allOf: + - $ref: pwm.yaml# + +properties: + compatible: + const: kontron,sl28cpld-pwm + + reg: + maxItems: 1 + + "#pwm-cells": + const: 2 + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml b/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml new file mode 100644 index 000000000000..179272f74de5 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/kontron,sl28cpld-wdt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Watchdog driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see ../mfd/kontron,sl28cpld.yaml. + +allOf: + - $ref: watchdog.yaml# + +properties: + compatible: + const: kontron,sl28cpld-wdt + + reg: + maxItems: 1 + + kontron,assert-wdt-timeout-pin: + description: The SMARC standard defines a WDT_TIME_OUT# pin. If this + property is set, this output will be pulsed when the watchdog bites + and the system resets. + type: boolean + +required: + - compatible + +additionalProperties: false -- cgit v1.2.3 From a538ad229bbee4f8c68204c75b2e1ae43db875d6 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:31 +0200 Subject: mfd: simple-mfd-i2c: Add sl28cpld support Add the core support for the board management controller found on the SMARC-sAL28 board. Also add a virtual symbol which pulls in the simple-mfd-i2c driver and provide a common symbol on which the subdevice drivers can depend on. At the moment, this controller is used on the Kontron SMARC-sAL28 board. Signed-off-by: Michael Walle Signed-off-by: Lee Jones --- drivers/mfd/Kconfig | 10 ++++++++++ drivers/mfd/simple-mfd-i2c.c | 1 + 2 files changed, 11 insertions(+) diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 6e1a38944d28..ed90eb5bdc83 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -1174,6 +1174,16 @@ config MFD_SIMPLE_MFD_I2C sub-devices represented by child nodes in Device Tree will be subsequently registered. +config MFD_SL28CPLD + tristate "Kontron sl28cpld Board Management Controller" + select MFD_SIMPLE_MFD_I2C + help + Say yes here to enable support for the Kontron sl28cpld board + management controller. + + It can be found on the following boards: + * SMARC-sAL28 + config MFD_SM501 tristate "Silicon Motion SM501" depends on HAS_DMA diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c index 28e96a246be1..87f684cff9a1 100644 --- a/drivers/mfd/simple-mfd-i2c.c +++ b/drivers/mfd/simple-mfd-i2c.c @@ -38,6 +38,7 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c) } static const struct of_device_id simple_mfd_i2c_of_match[] = { + { .compatible = "kontron,sl28cpld" }, {} }; MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match); -- cgit v1.2.3 From 03ac990e0ac0c2823282d5b8dd2d536d88bbe6c2 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:32 +0200 Subject: irqchip: Add sl28cpld interrupt controller support Add support for the interrupt controller inside the sl28 CPLD management controller. The interrupt controller can handle at most 8 interrupts and is really simplistic and consists only of an interrupt mask and an interrupt pending register. Signed-off-by: Michael Walle Acked-by: Marc Zyngier Signed-off-by: Lee Jones --- drivers/irqchip/Kconfig | 8 ++++ drivers/irqchip/Makefile | 1 + drivers/irqchip/irq-sl28cpld.c | 96 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 105 insertions(+) create mode 100644 drivers/irqchip/irq-sl28cpld.c diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig index bb70b7177f94..19cd32ba2155 100644 --- a/drivers/irqchip/Kconfig +++ b/drivers/irqchip/Kconfig @@ -246,6 +246,14 @@ config RENESAS_RZA1_IRQC Enable support for the Renesas RZ/A1 Interrupt Controller, to use up to 8 external interrupts with configurable sense select. +config SL28CPLD_INTC + bool "Kontron sl28cpld IRQ controller" + depends on MFD_SL28CPLD=y || COMPILE_TEST + select REGMAP_IRQ + help + Interrupt controller driver for the board management controller + found on the Kontron sl28 CPLD. + config ST_IRQCHIP bool select REGMAP diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile index 133f9c45744a..39af7d89204d 100644 --- a/drivers/irqchip/Makefile +++ b/drivers/irqchip/Makefile @@ -111,3 +111,4 @@ obj-$(CONFIG_LOONGSON_HTPIC) += irq-loongson-htpic.o obj-$(CONFIG_LOONGSON_HTVEC) += irq-loongson-htvec.o obj-$(CONFIG_LOONGSON_PCH_PIC) += irq-loongson-pch-pic.o obj-$(CONFIG_LOONGSON_PCH_MSI) += irq-loongson-pch-msi.o +obj-$(CONFIG_SL28CPLD_INTC) += irq-sl28cpld.o diff --git a/drivers/irqchip/irq-sl28cpld.c b/drivers/irqchip/irq-sl28cpld.c new file mode 100644 index 000000000000..0aa50d025ef6 --- /dev/null +++ b/drivers/irqchip/irq-sl28cpld.c @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld interrupt controller driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include + +#define INTC_IE 0x00 +#define INTC_IP 0x01 + +static const struct regmap_irq sl28cpld_irqs[] = { + REGMAP_IRQ_REG_LINE(0, 8), + REGMAP_IRQ_REG_LINE(1, 8), + REGMAP_IRQ_REG_LINE(2, 8), + REGMAP_IRQ_REG_LINE(3, 8), + REGMAP_IRQ_REG_LINE(4, 8), + REGMAP_IRQ_REG_LINE(5, 8), + REGMAP_IRQ_REG_LINE(6, 8), + REGMAP_IRQ_REG_LINE(7, 8), +}; + +struct sl28cpld_intc { + struct regmap *regmap; + struct regmap_irq_chip chip; + struct regmap_irq_chip_data *irq_data; +}; + +static int sl28cpld_intc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct sl28cpld_intc *irqchip; + int irq; + u32 base; + int ret; + + if (!dev->parent) + return -ENODEV; + + irqchip = devm_kzalloc(dev, sizeof(*irqchip), GFP_KERNEL); + if (!irqchip) + return -ENOMEM; + + irqchip->regmap = dev_get_regmap(dev->parent, NULL); + if (!irqchip->regmap) + return -ENODEV; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + ret = device_property_read_u32(&pdev->dev, "reg", &base); + if (ret) + return -EINVAL; + + irqchip->chip.name = "sl28cpld-intc"; + irqchip->chip.irqs = sl28cpld_irqs; + irqchip->chip.num_irqs = ARRAY_SIZE(sl28cpld_irqs); + irqchip->chip.num_regs = 1; + irqchip->chip.status_base = base + INTC_IP; + irqchip->chip.mask_base = base + INTC_IE; + irqchip->chip.mask_invert = true, + irqchip->chip.ack_base = base + INTC_IP; + + return devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev), + irqchip->regmap, irq, + IRQF_SHARED | IRQF_ONESHOT, 0, + &irqchip->chip, + &irqchip->irq_data); +} + +static const struct of_device_id sl28cpld_intc_of_match[] = { + { .compatible = "kontron,sl28cpld-intc" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_intc_of_match); + +static struct platform_driver sl28cpld_intc_driver = { + .probe = sl28cpld_intc_probe, + .driver = { + .name = "sl28cpld-intc", + .of_match_table = sl28cpld_intc_of_match, + } +}; +module_platform_driver(sl28cpld_intc_driver); + +MODULE_DESCRIPTION("sl28cpld Interrupt Controller Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 85174ca663767c1c6f8dca3b0a2acfd4b5c37289 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:33 +0200 Subject: watchdog: add support for sl28cpld watchdog Add support for the watchdog of the sl28cpld board management controller. This is part of a multi-function device driver. Signed-off-by: Michael Walle Acked-by: Guenter Roeck Signed-off-by: Lee Jones --- drivers/watchdog/Kconfig | 11 ++ drivers/watchdog/Makefile | 1 + drivers/watchdog/sl28cpld_wdt.c | 229 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 241 insertions(+) create mode 100644 drivers/watchdog/sl28cpld_wdt.c diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index ab7aad5a1e69..ba698340ed6f 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -340,6 +340,17 @@ config MLX_WDT To compile this driver as a module, choose M here: the module will be called mlx-wdt. +config SL28CPLD_WATCHDOG + tristate "Kontron sl28cpld Watchdog" + depends on MFD_SL28CPLD || COMPILE_TEST + select WATCHDOG_CORE + help + Say Y here to include support for the watchdog timer + on the Kontron sl28 CPLD. + + To compile this driver as a module, choose M here: the + module will be called sl28cpld_wdt. + # ALPHA Architecture # ARM Architecture diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile index 97bed1d3d97c..aa6e41126901 100644 --- a/drivers/watchdog/Makefile +++ b/drivers/watchdog/Makefile @@ -225,3 +225,4 @@ obj-$(CONFIG_MENF21BMC_WATCHDOG) += menf21bmc_wdt.o obj-$(CONFIG_MENZ069_WATCHDOG) += menz69_wdt.o obj-$(CONFIG_RAVE_SP_WATCHDOG) += rave-sp-wdt.o obj-$(CONFIG_STPMIC1_WATCHDOG) += stpmic1_wdt.o +obj-$(CONFIG_SL28CPLD_WATCHDOG) += sl28cpld_wdt.o diff --git a/drivers/watchdog/sl28cpld_wdt.c b/drivers/watchdog/sl28cpld_wdt.c new file mode 100644 index 000000000000..a45047d8d9ab --- /dev/null +++ b/drivers/watchdog/sl28cpld_wdt.c @@ -0,0 +1,229 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld watchdog driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include + +/* + * Watchdog timer block registers. + */ +#define WDT_CTRL 0x00 +#define WDT_CTRL_EN BIT(0) +#define WDT_CTRL_LOCK BIT(2) +#define WDT_CTRL_ASSERT_SYS_RESET BIT(6) +#define WDT_CTRL_ASSERT_WDT_TIMEOUT BIT(7) +#define WDT_TIMEOUT 0x01 +#define WDT_KICK 0x02 +#define WDT_KICK_VALUE 0x6b +#define WDT_COUNT 0x03 + +#define WDT_DEFAULT_TIMEOUT 10 + +static bool nowayout = WATCHDOG_NOWAYOUT; +module_param(nowayout, bool, 0); +MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" + __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); + +static int timeout; +module_param(timeout, int, 0); +MODULE_PARM_DESC(timeout, "Initial watchdog timeout in seconds"); + +struct sl28cpld_wdt { + struct watchdog_device wdd; + struct regmap *regmap; + u32 offset; + bool assert_wdt_timeout; +}; + +static int sl28cpld_wdt_ping(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + + return regmap_write(wdt->regmap, wdt->offset + WDT_KICK, + WDT_KICK_VALUE); +} + +static int sl28cpld_wdt_start(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + unsigned int val; + + val = WDT_CTRL_EN | WDT_CTRL_ASSERT_SYS_RESET; + if (wdt->assert_wdt_timeout) + val |= WDT_CTRL_ASSERT_WDT_TIMEOUT; + if (nowayout) + val |= WDT_CTRL_LOCK; + + return regmap_update_bits(wdt->regmap, wdt->offset + WDT_CTRL, + val, val); +} + +static int sl28cpld_wdt_stop(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + + return regmap_update_bits(wdt->regmap, wdt->offset + WDT_CTRL, + WDT_CTRL_EN, 0); +} + +static unsigned int sl28cpld_wdt_get_timeleft(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + unsigned int val; + int ret; + + ret = regmap_read(wdt->regmap, wdt->offset + WDT_COUNT, &val); + if (ret) + return 0; + + return val; +} + +static int sl28cpld_wdt_set_timeout(struct watchdog_device *wdd, + unsigned int timeout) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + int ret; + + ret = regmap_write(wdt->regmap, wdt->offset + WDT_TIMEOUT, timeout); + if (ret) + return ret; + + wdd->timeout = timeout; + + return 0; +} + +static const struct watchdog_info sl28cpld_wdt_info = { + .options = WDIOF_MAGICCLOSE | WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING, + .identity = "sl28cpld watchdog", +}; + +static struct watchdog_ops sl28cpld_wdt_ops = { + .owner = THIS_MODULE, + .start = sl28cpld_wdt_start, + .stop = sl28cpld_wdt_stop, + .ping = sl28cpld_wdt_ping, + .set_timeout = sl28cpld_wdt_set_timeout, + .get_timeleft = sl28cpld_wdt_get_timeleft, +}; + +static int sl28cpld_wdt_probe(struct platform_device *pdev) +{ + struct watchdog_device *wdd; + struct sl28cpld_wdt *wdt; + unsigned int status; + unsigned int val; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL); + if (!wdt) + return -ENOMEM; + + wdt->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!wdt->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &wdt->offset); + if (ret) + return -EINVAL; + + wdt->assert_wdt_timeout = device_property_read_bool(&pdev->dev, + "kontron,assert-wdt-timeout-pin"); + + /* initialize struct watchdog_device */ + wdd = &wdt->wdd; + wdd->parent = &pdev->dev; + wdd->info = &sl28cpld_wdt_info; + wdd->ops = &sl28cpld_wdt_ops; + wdd->min_timeout = 1; + wdd->max_timeout = 255; + + watchdog_set_drvdata(wdd, wdt); + watchdog_stop_on_reboot(wdd); + + /* + * Read the status early, in case of an error, we haven't modified the + * hardware. + */ + ret = regmap_read(wdt->regmap, wdt->offset + WDT_CTRL, &status); + if (ret) + return ret; + + /* + * Initial timeout value, may be overwritten by device tree or module + * parmeter in watchdog_init_timeout(). + * + * Reading a zero here means that either the hardware has a default + * value of zero (which is very unlikely and definitely a hardware + * bug) or the bootloader set it to zero. In any case, we handle + * this case gracefully and set out own timeout. + */ + ret = regmap_read(wdt->regmap, wdt->offset + WDT_TIMEOUT, &val); + if (ret) + return ret; + + if (val) + wdd->timeout = val; + else + wdd->timeout = WDT_DEFAULT_TIMEOUT; + + watchdog_init_timeout(wdd, timeout, &pdev->dev); + sl28cpld_wdt_set_timeout(wdd, wdd->timeout); + + /* if the watchdog is locked, we set nowayout */ + if (status & WDT_CTRL_LOCK) + nowayout = true; + watchdog_set_nowayout(wdd, nowayout); + + /* + * If watchdog is already running, keep it enabled, but make + * sure its mode is set correctly. + */ + if (status & WDT_CTRL_EN) { + sl28cpld_wdt_start(wdd); + set_bit(WDOG_HW_RUNNING, &wdd->status); + } + + ret = devm_watchdog_register_device(&pdev->dev, wdd); + if (ret < 0) { + dev_err(&pdev->dev, "failed to register watchdog device\n"); + return ret; + } + + dev_info(&pdev->dev, "initial timeout %d sec%s\n", + wdd->timeout, nowayout ? ", nowayout" : ""); + + return 0; +} + +static const struct of_device_id sl28cpld_wdt_of_match[] = { + { .compatible = "kontron,sl28cpld-wdt" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_wdt_of_match); + +static struct platform_driver sl28cpld_wdt_driver = { + .probe = sl28cpld_wdt_probe, + .driver = { + .name = "sl28cpld-wdt", + .of_match_table = sl28cpld_wdt_of_match, + }, +}; +module_platform_driver(sl28cpld_wdt_driver); + +MODULE_DESCRIPTION("sl28cpld Watchdog Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 9db33d221efcca9503ac481edcbf2b3f4404bdb8 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:34 +0200 Subject: pwm: Add support for sl28cpld PWM controller MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add support for the PWM controller of the sl28cpld board management controller. This is part of a multi-function device driver. The controller has one PWM channel and can just generate four distinct frequencies. Signed-off-by: Michael Walle Acked-by: Thierry Reding Reviewed-by: Uwe Kleine-König Signed-off-by: Lee Jones --- drivers/pwm/Kconfig | 10 ++ drivers/pwm/Makefile | 1 + drivers/pwm/pwm-sl28cpld.c | 270 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 281 insertions(+) create mode 100644 drivers/pwm/pwm-sl28cpld.c diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig index 7dbcf6973d33..78ddc127e45e 100644 --- a/drivers/pwm/Kconfig +++ b/drivers/pwm/Kconfig @@ -428,6 +428,16 @@ config PWM_SIFIVE To compile this driver as a module, choose M here: the module will be called pwm-sifive. +config PWM_SL28CPLD + tristate "Kontron sl28cpld PWM support" + depends on MFD_SL28CPLD || COMPILE_TEST + help + Generic PWM framework driver for board management controller + found on the Kontron sl28 CPLD. + + To compile this driver as a module, choose M here: the module + will be called pwm-sl28cpld. + config PWM_SPEAR tristate "STMicroelectronics SPEAr PWM support" depends on PLAT_SPEAR || COMPILE_TEST diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile index 2c2ba0a03557..cbdcd55d69ee 100644 --- a/drivers/pwm/Makefile +++ b/drivers/pwm/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o obj-$(CONFIG_PWM_SIFIVE) += pwm-sifive.o +obj-$(CONFIG_PWM_SL28CPLD) += pwm-sl28cpld.o obj-$(CONFIG_PWM_SPEAR) += pwm-spear.o obj-$(CONFIG_PWM_SPRD) += pwm-sprd.o obj-$(CONFIG_PWM_STI) += pwm-sti.o diff --git a/drivers/pwm/pwm-sl28cpld.c b/drivers/pwm/pwm-sl28cpld.c new file mode 100644 index 000000000000..5046b6b7fd35 --- /dev/null +++ b/drivers/pwm/pwm-sl28cpld.c @@ -0,0 +1,270 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld PWM driver + * + * Copyright (c) 2020 Michael Walle + * + * There is no public datasheet available for this PWM core. But it is easy + * enough to be briefly explained. It consists of one 8-bit counter. The PWM + * supports four distinct frequencies by selecting when to reset the counter. + * With the prescaler setting you can select which bit of the counter is used + * to reset it. This implies that the higher the frequency the less remaining + * bits are available for the actual counter. + * + * Let cnt[7:0] be the counter, clocked at 32kHz: + * +-----------+--------+--------------+-----------+---------------+ + * | prescaler | reset | counter bits | frequency | period length | + * +-----------+--------+--------------+-----------+---------------+ + * | 0 | cnt[7] | cnt[6:0] | 250 Hz | 4000000 ns | + * | 1 | cnt[6] | cnt[5:0] | 500 Hz | 2000000 ns | + * | 2 | cnt[5] | cnt[4:0] | 1 kHz | 1000000 ns | + * | 3 | cnt[4] | cnt[3:0] | 2 kHz | 500000 ns | + * +-----------+--------+--------------+-----------+---------------+ + * + * Limitations: + * - The hardware cannot generate a 100% duty cycle if the prescaler is 0. + * - The hardware cannot atomically set the prescaler and the counter value, + * which might lead to glitches and inconsistent states if a write fails. + * - The counter is not reset if you switch the prescaler which leads + * to glitches, too. + * - The duty cycle will switch immediately and not after a complete cycle. + * - Depending on the actual implementation, disabling the PWM might have + * side effects. For example, if the output pin is shared with a GPIO pin + * it will automatically switch back to GPIO mode. + */ + +#include +#include +#include +#include +#include +#include +#include + +/* + * PWM timer block registers. + */ +#define SL28CPLD_PWM_CTRL 0x00 +#define SL28CPLD_PWM_CTRL_ENABLE BIT(7) +#define SL28CPLD_PWM_CTRL_PRESCALER_MASK GENMASK(1, 0) +#define SL28CPLD_PWM_CYCLE 0x01 +#define SL28CPLD_PWM_CYCLE_MAX GENMASK(6, 0) + +#define SL28CPLD_PWM_CLK 32000 /* 32 kHz */ +#define SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler) (1 << (7 - (prescaler))) +#define SL28CPLD_PWM_PERIOD(prescaler) \ + (NSEC_PER_SEC / SL28CPLD_PWM_CLK * SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler)) + +/* + * We calculate the duty cycle like this: + * duty_cycle_ns = pwm_cycle_reg * max_period_ns / max_duty_cycle + * + * With + * max_period_ns = 1 << (7 - prescaler) / SL28CPLD_PWM_CLK * NSEC_PER_SEC + * max_duty_cycle = 1 << (7 - prescaler) + * this then simplifies to: + * duty_cycle_ns = pwm_cycle_reg / SL28CPLD_PWM_CLK * NSEC_PER_SEC + * = NSEC_PER_SEC / SL28CPLD_PWM_CLK * pwm_cycle_reg + * + * NSEC_PER_SEC is a multiple of SL28CPLD_PWM_CLK, therefore we're not losing + * precision by doing the divison first. + */ +#define SL28CPLD_PWM_TO_DUTY_CYCLE(reg) \ + (NSEC_PER_SEC / SL28CPLD_PWM_CLK * (reg)) +#define SL28CPLD_PWM_FROM_DUTY_CYCLE(duty_cycle) \ + (DIV_ROUND_DOWN_ULL((duty_cycle), NSEC_PER_SEC / SL28CPLD_PWM_CLK)) + +#define sl28cpld_pwm_read(priv, reg, val) \ + regmap_read((priv)->regmap, (priv)->offset + (reg), (val)) +#define sl28cpld_pwm_write(priv, reg, val) \ + regmap_write((priv)->regmap, (priv)->offset + (reg), (val)) + +struct sl28cpld_pwm { + struct pwm_chip pwm_chip; + struct regmap *regmap; + u32 offset; +}; + +static void sl28cpld_pwm_get_state(struct pwm_chip *chip, + struct pwm_device *pwm, + struct pwm_state *state) +{ + struct sl28cpld_pwm *priv = dev_get_drvdata(chip->dev); + unsigned int reg; + int prescaler; + + sl28cpld_pwm_read(priv, SL28CPLD_PWM_CTRL, ®); + + state->enabled = reg & SL28CPLD_PWM_CTRL_ENABLE; + + prescaler = FIELD_GET(SL28CPLD_PWM_CTRL_PRESCALER_MASK, reg); + state->period = SL28CPLD_PWM_PERIOD(prescaler); + + sl28cpld_pwm_read(priv, SL28CPLD_PWM_CYCLE, ®); + state->duty_cycle = SL28CPLD_PWM_TO_DUTY_CYCLE(reg); + state->polarity = PWM_POLARITY_NORMAL; + + /* + * Sanitize values for the PWM core. Depending on the prescaler it + * might happen that we calculate a duty_cycle greater than the actual + * period. This might happen if someone (e.g. the bootloader) sets an + * invalid combination of values. The behavior of the hardware is + * undefined in this case. But we need to report sane values back to + * the PWM core. + */ + state->duty_cycle = min(state->duty_cycle, state->period); +} + +static int sl28cpld_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, + const struct pwm_state *state) +{ + struct sl28cpld_pwm *priv = dev_get_drvdata(chip->dev); + unsigned int cycle, prescaler; + bool write_duty_cycle_first; + int ret; + u8 ctrl; + + /* Polarity inversion is not supported */ + if (state->polarity != PWM_POLARITY_NORMAL) + return -EINVAL; + + /* + * Calculate the prescaler. Pick the biggest period that isn't + * bigger than the requested period. + */ + prescaler = DIV_ROUND_UP_ULL(SL28CPLD_PWM_PERIOD(0), state->period); + prescaler = order_base_2(prescaler); + + if (prescaler > field_max(SL28CPLD_PWM_CTRL_PRESCALER_MASK)) + return -ERANGE; + + ctrl = FIELD_PREP(SL28CPLD_PWM_CTRL_PRESCALER_MASK, prescaler); + if (state->enabled) + ctrl |= SL28CPLD_PWM_CTRL_ENABLE; + + cycle = SL28CPLD_PWM_FROM_DUTY_CYCLE(state->duty_cycle); + cycle = min_t(unsigned int, cycle, SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler)); + + /* + * Work around the hardware limitation. See also above. Trap 100% duty + * cycle if the prescaler is 0. Set prescaler to 1 instead. We don't + * care about the frequency because its "all-one" in either case. + * + * We don't need to check the actual prescaler setting, because only + * if the prescaler is 0 we can have this particular value. + */ + if (cycle == SL28CPLD_PWM_MAX_DUTY_CYCLE(0)) { + ctrl &= ~SL28CPLD_PWM_CTRL_PRESCALER_MASK; + ctrl |= FIELD_PREP(SL28CPLD_PWM_CTRL_PRESCALER_MASK, 1); + cycle = SL28CPLD_PWM_MAX_DUTY_CYCLE(1); + } + + /* + * To avoid glitches when we switch the prescaler, we have to make sure + * we have a valid duty cycle for the new mode. + * + * Take the current prescaler (or the current period length) into + * account to decide whether we have to write the duty cycle or the new + * prescaler first. If the period length is decreasing we have to + * write the duty cycle first. + */ + write_duty_cycle_first = pwm->state.period > state->period; + + if (write_duty_cycle_first) { + ret = sl28cpld_pwm_write(priv, SL28CPLD_PWM_CYCLE, cycle); + if (ret) + return ret; + } + + ret = sl28cpld_pwm_write(priv, SL28CPLD_PWM_CTRL, ctrl); + if (ret) + return ret; + + if (!write_duty_cycle_first) { + ret = sl28cpld_pwm_write(priv, SL28CPLD_PWM_CYCLE, cycle); + if (ret) + return ret; + } + + return 0; +} + +static const struct pwm_ops sl28cpld_pwm_ops = { + .apply = sl28cpld_pwm_apply, + .get_state = sl28cpld_pwm_get_state, + .owner = THIS_MODULE, +}; + +static int sl28cpld_pwm_probe(struct platform_device *pdev) +{ + struct sl28cpld_pwm *priv; + struct pwm_chip *chip; + int ret; + + if (!pdev->dev.parent) { + dev_err(&pdev->dev, "no parent device\n"); + return -ENODEV; + } + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!priv->regmap) { + dev_err(&pdev->dev, "could not get parent regmap\n"); + return -ENODEV; + } + + ret = device_property_read_u32(&pdev->dev, "reg", &priv->offset); + if (ret) { + dev_err(&pdev->dev, "no 'reg' property found (%pe)\n", + ERR_PTR(ret)); + return -EINVAL; + } + + /* Initialize the pwm_chip structure */ + chip = &priv->pwm_chip; + chip->dev = &pdev->dev; + chip->ops = &sl28cpld_pwm_ops; + chip->base = -1; + chip->npwm = 1; + + ret = pwmchip_add(&priv->pwm_chip); + if (ret) { + dev_err(&pdev->dev, "failed to add PWM chip (%pe)", + ERR_PTR(ret)); + return ret; + } + + platform_set_drvdata(pdev, priv); + + return 0; +} + +static int sl28cpld_pwm_remove(struct platform_device *pdev) +{ + struct sl28cpld_pwm *priv = platform_get_drvdata(pdev); + + return pwmchip_remove(&priv->pwm_chip); +} + +static const struct of_device_id sl28cpld_pwm_of_match[] = { + { .compatible = "kontron,sl28cpld-pwm" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_pwm_of_match); + +static struct platform_driver sl28cpld_pwm_driver = { + .probe = sl28cpld_pwm_probe, + .remove = sl28cpld_pwm_remove, + .driver = { + .name = "sl28cpld-pwm", + .of_match_table = sl28cpld_pwm_of_match, + }, +}; +module_platform_driver(sl28cpld_pwm_driver); + +MODULE_DESCRIPTION("sl28cpld PWM Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From b7536d8749e54923c9a7e8c4175e1e4f9b8c1541 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:35 +0200 Subject: gpio: Add support for the sl28cpld GPIO controller Add support for the GPIO controller of the sl28 board management controller. This driver is part of a multi-function device. A controller has 8 lines. There are three different flavors: full-featured GPIO with interrupt support, input-only and output-only. Signed-off-by: Michael Walle Reviewed-by: Linus Walleij Reviewed-by: Andy Shevchenko Signed-off-by: Lee Jones --- drivers/gpio/Kconfig | 12 ++++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-sl28cpld.c | 161 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 174 insertions(+) create mode 100644 drivers/gpio/gpio-sl28cpld.c diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 8030fd91a3cc..3799cb6048a2 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -1223,6 +1223,18 @@ config GPIO_RC5T583 This driver provides the support for driving/reading the gpio pins of RC5T583 device through standard gpio library. +config GPIO_SL28CPLD + tristate "Kontron sl28cpld GPIO support" + depends on MFD_SL28CPLD || COMPILE_TEST + select GPIO_REGMAP + select GPIOLIB_IRQCHIP + select REGMAP_IRQ + help + This enables support for the GPIOs found on the Kontron sl28 CPLD. + + This driver can also be built as a module. If so, the module will be + called gpio-sl28cpld. + config GPIO_STMPE bool "STMPE GPIOs" depends on MFD_STMPE diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 4f9abff4f2dc..c3a4e7c94a91 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -132,6 +132,7 @@ obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o obj-$(CONFIG_GPIO_SCH) += gpio-sch.o obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o obj-$(CONFIG_GPIO_SIOX) += gpio-siox.o +obj-$(CONFIG_GPIO_SL28CPLD) += gpio-sl28cpld.o obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o obj-$(CONFIG_GPIO_SPRD) += gpio-sprd.o diff --git a/drivers/gpio/gpio-sl28cpld.c b/drivers/gpio/gpio-sl28cpld.c new file mode 100644 index 000000000000..889b8f5622c2 --- /dev/null +++ b/drivers/gpio/gpio-sl28cpld.c @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld GPIO driver + * + * Copyright 2020 Michael Walle + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* GPIO flavor */ +#define GPIO_REG_DIR 0x00 +#define GPIO_REG_OUT 0x01 +#define GPIO_REG_IN 0x02 +#define GPIO_REG_IE 0x03 +#define GPIO_REG_IP 0x04 + +/* input-only flavor */ +#define GPI_REG_IN 0x00 + +/* output-only flavor */ +#define GPO_REG_OUT 0x00 + +enum sl28cpld_gpio_type { + SL28CPLD_GPIO = 1, + SL28CPLD_GPI, + SL28CPLD_GPO, +}; + +static const struct regmap_irq sl28cpld_gpio_irqs[] = { + REGMAP_IRQ_REG_LINE(0, 8), + REGMAP_IRQ_REG_LINE(1, 8), + REGMAP_IRQ_REG_LINE(2, 8), + REGMAP_IRQ_REG_LINE(3, 8), + REGMAP_IRQ_REG_LINE(4, 8), + REGMAP_IRQ_REG_LINE(5, 8), + REGMAP_IRQ_REG_LINE(6, 8), + REGMAP_IRQ_REG_LINE(7, 8), +}; + +static int sl28cpld_gpio_irq_init(struct platform_device *pdev, + unsigned int base, + struct gpio_regmap_config *config) +{ + struct regmap_irq_chip_data *irq_data; + struct regmap_irq_chip *irq_chip; + struct device *dev = &pdev->dev; + int irq, ret; + + if (!device_property_read_bool(dev, "interrupt-controller")) + return 0; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + irq_chip = devm_kzalloc(dev, sizeof(*irq_chip), GFP_KERNEL); + if (!irq_chip) + return -ENOMEM; + + irq_chip->name = "sl28cpld-gpio-irq", + irq_chip->irqs = sl28cpld_gpio_irqs; + irq_chip->num_irqs = ARRAY_SIZE(sl28cpld_gpio_irqs); + irq_chip->num_regs = 1; + irq_chip->status_base = base + GPIO_REG_IP; + irq_chip->mask_base = base + GPIO_REG_IE; + irq_chip->mask_invert = true, + irq_chip->ack_base = base + GPIO_REG_IP; + + ret = devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev), + config->regmap, irq, + IRQF_SHARED | IRQF_ONESHOT, + 0, irq_chip, &irq_data); + if (ret) + return ret; + + config->irq_domain = regmap_irq_get_domain(irq_data); + + return 0; +} + +static int sl28cpld_gpio_probe(struct platform_device *pdev) +{ + struct gpio_regmap_config config = {0}; + enum sl28cpld_gpio_type type; + struct regmap *regmap; + u32 base; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + type = (uintptr_t)device_get_match_data(&pdev->dev); + if (!type) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &base); + if (ret) + return -EINVAL; + + regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!regmap) + return -ENODEV; + + config.regmap = regmap; + config.parent = &pdev->dev; + config.ngpio = 8; + + switch (type) { + case SL28CPLD_GPIO: + config.reg_dat_base = base + GPIO_REG_IN; + config.reg_set_base = base + GPIO_REG_OUT; + /* reg_dir_out_base might be zero */ + config.reg_dir_out_base = GPIO_REGMAP_ADDR(base + GPIO_REG_DIR); + + /* This type supports interrupts */ + ret = sl28cpld_gpio_irq_init(pdev, base, &config); + if (ret) + return ret; + break; + case SL28CPLD_GPO: + config.reg_set_base = base + GPO_REG_OUT; + break; + case SL28CPLD_GPI: + config.reg_dat_base = base + GPI_REG_IN; + break; + default: + dev_err(&pdev->dev, "unknown type %d\n", type); + return -ENODEV; + } + + return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(&pdev->dev, &config)); +} + +static const struct of_device_id sl28cpld_gpio_of_match[] = { + { .compatible = "kontron,sl28cpld-gpio", .data = (void *)SL28CPLD_GPIO }, + { .compatible = "kontron,sl28cpld-gpi", .data = (void *)SL28CPLD_GPI }, + { .compatible = "kontron,sl28cpld-gpo", .data = (void *)SL28CPLD_GPO }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_gpio_of_match); + +static struct platform_driver sl28cpld_gpio_driver = { + .probe = sl28cpld_gpio_probe, + .driver = { + .name = "sl28cpld-gpio", + .of_match_table = sl28cpld_gpio_of_match, + }, +}; +module_platform_driver(sl28cpld_gpio_driver); + +MODULE_DESCRIPTION("sl28cpld GPIO Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 3f697027bcb0959d7c24d59550ab1da07c2dd609 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 14 Sep 2020 23:43:36 +0200 Subject: hwmon: Add support for the sl28cpld hardware monitoring controller Add support for the hardware monitoring controller of the sl28cpld board management controller. This driver is part of a multi-function device. Signed-off-by: Michael Walle Acked-by: Guenter Roeck Reviewed-by: Andy Shevchenko Signed-off-by: Lee Jones --- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/sl28cpld.rst | 36 ++++++++++ drivers/hwmon/Kconfig | 10 +++ drivers/hwmon/Makefile | 1 + drivers/hwmon/sl28cpld-hwmon.c | 142 +++++++++++++++++++++++++++++++++++++++ 5 files changed, 190 insertions(+) create mode 100644 Documentation/hwmon/sl28cpld.rst create mode 100644 drivers/hwmon/sl28cpld-hwmon.c diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 750d3a975d82..d90c43c82936 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -154,6 +154,7 @@ Hardware Monitoring Kernel Drivers sht3x shtc1 sis5595 + sl28cpld smm665 smsc47b397 smsc47m192 diff --git a/Documentation/hwmon/sl28cpld.rst b/Documentation/hwmon/sl28cpld.rst new file mode 100644 index 000000000000..7ed65f78250c --- /dev/null +++ b/Documentation/hwmon/sl28cpld.rst @@ -0,0 +1,36 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +Kernel driver sl28cpld +====================== + +Supported chips: + + * Kontron sl28cpld + + Prefix: 'sl28cpld' + + Datasheet: not available + +Authors: Michael Walle + +Description +----------- + +The sl28cpld is a board management controller which also exposes a hardware +monitoring controller. At the moment this controller supports a single fan +supervisor. In the future there might be other flavours and additional +hardware monitoring might be supported. + +The fan supervisor has a 7 bit counter register and a counter period of 1 +second. If the 7 bit counter overflows, the supervisor will automatically +switch to x8 mode to support a wider input range at the loss of +granularity. + +Sysfs entries +------------- + +The following attributes are supported. + +======================= ======================================================== +fan1_input Fan RPM. Assuming 2 pulses per revolution. +======================= ======================================================== diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 8dc28b26916e..d98c0a6860d1 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1479,6 +1479,16 @@ config SENSORS_RASPBERRYPI_HWMON This driver can also be built as a module. If so, the module will be called raspberrypi-hwmon. +config SENSORS_SL28CPLD + tristate "Kontron sl28cpld hardware monitoring driver" + depends on MFD_SL28CPLD || COMPILE_TEST + help + If you say yes here you get support for the fan supervisor of the + sl28cpld board management controller. + + This driver can also be built as a module. If so, the module + will be called sl28cpld-hwmon. + config SENSORS_SHT15 tristate "Sensiron humidity and temperature sensors. SHT15 and compat." depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index a8f4b35b136b..dee8511f9348 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -159,6 +159,7 @@ obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o +obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o obj-$(CONFIG_SENSORS_SHT15) += sht15.o obj-$(CONFIG_SENSORS_SHT21) += sht21.o obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o diff --git a/drivers/hwmon/sl28cpld-hwmon.c b/drivers/hwmon/sl28cpld-hwmon.c new file mode 100644 index 000000000000..e48f58ec5b9c --- /dev/null +++ b/drivers/hwmon/sl28cpld-hwmon.c @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld hardware monitoring driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define FAN_INPUT 0x00 +#define FAN_SCALE_X8 BIT(7) +#define FAN_VALUE_MASK GENMASK(6, 0) + +struct sl28cpld_hwmon { + struct regmap *regmap; + u32 offset; +}; + +static umode_t sl28cpld_hwmon_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + return 0444; +} + +static int sl28cpld_hwmon_read(struct device *dev, + enum hwmon_sensor_types type, u32 attr, + int channel, long *input) +{ + struct sl28cpld_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int value; + int ret; + + switch (attr) { + case hwmon_fan_input: + ret = regmap_read(hwmon->regmap, hwmon->offset + FAN_INPUT, + &value); + if (ret) + return ret; + /* + * The register has a 7 bit value and 1 bit which indicates the + * scale. If the MSB is set, then the lower 7 bit has to be + * multiplied by 8, to get the correct reading. + */ + if (value & FAN_SCALE_X8) + value = FIELD_GET(FAN_VALUE_MASK, value) << 3; + + /* + * The counter period is 1000ms and the sysfs specification + * says we should asssume 2 pulses per revolution. + */ + value *= 60 / 2; + + break; + default: + return -EOPNOTSUPP; + } + + *input = value; + return 0; +} + +static const u32 sl28cpld_hwmon_fan_config[] = { + HWMON_F_INPUT, + 0 +}; + +static const struct hwmon_channel_info sl28cpld_hwmon_fan = { + .type = hwmon_fan, + .config = sl28cpld_hwmon_fan_config, +}; + +static const struct hwmon_channel_info *sl28cpld_hwmon_info[] = { + &sl28cpld_hwmon_fan, + NULL +}; + +static const struct hwmon_ops sl28cpld_hwmon_ops = { + .is_visible = sl28cpld_hwmon_is_visible, + .read = sl28cpld_hwmon_read, +}; + +static const struct hwmon_chip_info sl28cpld_hwmon_chip_info = { + .ops = &sl28cpld_hwmon_ops, + .info = sl28cpld_hwmon_info, +}; + +static int sl28cpld_hwmon_probe(struct platform_device *pdev) +{ + struct sl28cpld_hwmon *hwmon; + struct device *hwmon_dev; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + hwmon->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!hwmon->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &hwmon->offset); + if (ret) + return -EINVAL; + + hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev, + "sl28cpld_hwmon", hwmon, + &sl28cpld_hwmon_chip_info, NULL); + if (IS_ERR(hwmon_dev)) + dev_err(&pdev->dev, "failed to register as hwmon device"); + + return PTR_ERR_OR_ZERO(hwmon_dev); +} + +static const struct of_device_id sl28cpld_hwmon_of_match[] = { + { .compatible = "kontron,sl28cpld-fan" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_hwmon_of_match); + +static struct platform_driver sl28cpld_hwmon_driver = { + .probe = sl28cpld_hwmon_probe, + .driver = { + .name = "sl28cpld-fan", + .of_match_table = sl28cpld_hwmon_of_match, + }, +}; +module_platform_driver(sl28cpld_hwmon_driver); + +MODULE_DESCRIPTION("sl28cpld Hardware Monitoring Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); -- cgit v1.2.3 From 31c53962d65fb813eded2332b0fff60ffaaf2368 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Wed, 12 Aug 2020 14:29:03 +0200 Subject: mfd: Kconfig: Fix typo of 'individual' individul -> individual Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Lee Jones --- drivers/mfd/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index ed90eb5bdc83..4b918fdcc7c7 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -493,7 +493,7 @@ config MFD_HI6421_PMIC Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi- functions, such as regulators, RTC, codec, Coulomb counter, etc. This driver includes core APIs _only_. You have to select - individul components like voltage regulators under corresponding + individual components like voltage regulators under corresponding menus in order to enable them. We communicate with the Hi6421 via memory-mapped I/O. -- cgit v1.2.3 From d1264a075ed65d6b174a4742e69186125e66fd27 Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Sat, 15 Aug 2020 18:56:10 +0200 Subject: mfd: rn5t618: Add a power supply subdevice The RN5T618 and RC5T619 both have a charger and a fuel gauge, so add a subdevice for it. According to drivers in the wild, things should be at least similar, but since it is not tested, add it only to the RC5T619. Signed-off-by: Andreas Kemnade Signed-off-by: Lee Jones --- drivers/mfd/rn5t618.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c index e25407ed3ad4..dc452df1f1bf 100644 --- a/drivers/mfd/rn5t618.c +++ b/drivers/mfd/rn5t618.c @@ -25,6 +25,7 @@ static const struct mfd_cell rn5t618_cells[] = { static const struct mfd_cell rc5t619_cells[] = { { .name = "rn5t618-adc" }, + { .name = "rn5t618-power" }, { .name = "rn5t618-regulator" }, { .name = "rc5t619-rtc" }, { .name = "rn5t618-wdt" }, -- cgit v1.2.3 From e26ea09b6e0995cb65760e44042e26d3e40452a7 Mon Sep 17 00:00:00 2001 From: Lee Jones Date: Fri, 28 Aug 2020 09:37:04 +0100 Subject: mfd: khadas-mcu: Fix randconfig 'unused-const-variable' warning When testing with !OF, the build system reports: >> drivers/mfd/khadas-mcu.c:125:34: warning: unused variable 'khadas_mcu_of_match' [-Wunused-const-variable] static const struct of_device_id khadas_mcu_of_match[] = { ^ Reported-by: kernel test robot Acked-by: Neil Armstrong Signed-off-by: Lee Jones --- drivers/mfd/khadas-mcu.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/mfd/khadas-mcu.c b/drivers/mfd/khadas-mcu.c index 44d5bb462dab..f3d418810693 100644 --- a/drivers/mfd/khadas-mcu.c +++ b/drivers/mfd/khadas-mcu.c @@ -122,11 +122,13 @@ static int khadas_mcu_probe(struct i2c_client *client, return 0; } +#ifdef CONFIG_OF static const struct of_device_id khadas_mcu_of_match[] = { { .compatible = "khadas,mcu", }, {}, }; MODULE_DEVICE_TABLE(of, khadas_mcu_of_match); +#endif static struct i2c_driver khadas_mcu_driver = { .driver = { -- cgit v1.2.3 From ffa9cda9e62fe0afb5e7899985d615bdb36a2a03 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Fri, 10 Jul 2020 01:12:27 +0200 Subject: dt-bindings: mfd: Add ENE KB3930 Embedded Controller binding Add binding document for the ENE KB3930 Embedded Controller. Signed-off-by: Lubomir Rintel Reviewed-by: Rob Herring Reviewed-by: Dmitry Osipenko Signed-off-by: Lee Jones --- .../devicetree/bindings/mfd/ene-kb3930.yaml | 55 ++++++++++++++++++++++ 1 file changed, 55 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/ene-kb3930.yaml diff --git a/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml b/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml new file mode 100644 index 000000000000..074243c40891 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ene-kb3930.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/ene-kb3930.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ENE KB3930 Embedded Controller bindings + +description: | + This binding describes the ENE KB3930 Embedded Controller attached to an + I2C bus. + +maintainers: + - Lubomir Rintel + +properties: + compatible: + items: + - enum: + - dell,wyse-ariel-ec # Dell Wyse Ariel board (3020) + - const: ene,kb3930 + reg: + maxItems: 1 + + off-gpios: + description: GPIO used with the shutdown protocol on Ariel + maxItems: 2 + + system-power-controller: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + embedded-controller@58 { + compatible = "dell,wyse-ariel-ec", "ene,kb3930"; + reg = <0x58>; + system-power-controller; + + off-gpios = <&gpio 126 GPIO_ACTIVE_HIGH>, + <&gpio 127 GPIO_ACTIVE_HIGH>; + }; + }; + +... -- cgit v1.2.3 From ede6b2d1dfc0d6a7b0b3161a2e911d464e28e0ad Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Fri, 10 Jul 2020 01:12:28 +0200 Subject: mfd: ene-kb3930: Add driver for ENE KB3930 Embedded Controller This driver provides access to the EC RAM of said embedded controller attached to the I2C bus as well as optionally supporting its slightly weird power-off/restart protocol. A particular implementation of the EC firmware can be identified by a model byte. If this driver identifies the Dell Ariel platform, it registers the appropriate cells. Signed-off-by: Lubomir Rintel Signed-off-by: Lee Jones --- drivers/mfd/Kconfig | 11 +++ drivers/mfd/Makefile | 1 + drivers/mfd/ene-kb3930.c | 212 +++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 224 insertions(+) create mode 100644 drivers/mfd/ene-kb3930.c diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 4b918fdcc7c7..e1d3bf77b245 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -398,6 +398,17 @@ config MFD_DLN2 etc. must be enabled in order to use the functionality of the device. +config MFD_ENE_KB3930 + tristate "ENE KB3930 Embedded Controller support" + depends on I2C + depends on MACH_MMP3_DT || COMPILE_TEST + select MFD_CORE + help + This adds support for the power-off functionality and access to + the registers that control LEDS and USB port power on ENE KB3930 + Embedded Controller. To use the LED functionality LEDS_ARIEL must + be enabled. + config MFD_EXYNOS_LPASS tristate "Samsung Exynos SoC Low Power Audio Subsystem" depends on ARCH_EXYNOS || COMPILE_TEST diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index 78d24a3e7c9e..e6c7520ed129 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_ARCH_BCM2835) += bcm2835-pm.o obj-$(CONFIG_MFD_BCM590XX) += bcm590xx.o obj-$(CONFIG_MFD_BD9571MWV) += bd9571mwv.o obj-$(CONFIG_MFD_CROS_EC_DEV) += cros_ec_dev.o +obj-$(CONFIG_MFD_ENE_KB3930) += ene-kb3930.o obj-$(CONFIG_MFD_EXYNOS_LPASS) += exynos-lpass.o obj-$(CONFIG_MFD_GATEWORKS_GSC) += gateworks-gsc.o diff --git a/drivers/mfd/ene-kb3930.c b/drivers/mfd/ene-kb3930.c new file mode 100644 index 000000000000..1c32ff586816 --- /dev/null +++ b/drivers/mfd/ene-kb3930.c @@ -0,0 +1,212 @@ +// SPDX-License-Identifier: BSD-2-Clause OR GPL-2.0-or-later +/* + * ENE KB3930 Embedded Controller Driver + * + * Copyright (C) 2020 Lubomir Rintel + */ + +#include +#include +#include +#include +#include +#include +#include + +/* I2C registers that are multiplexing access to the EC RAM. */ +enum { + EC_DATA_IN = 0x00, + EC_RAM_OUT = 0x80, + EC_RAM_IN = 0x81, +}; + +/* EC RAM registers. */ +enum { + EC_MODEL = 0x30, + EC_VERSION_MAJ = 0x31, + EC_VERSION_MIN = 0x32, +}; + +struct kb3930 { + struct i2c_client *client; + struct regmap *ram_regmap; + struct gpio_descs *off_gpios; +}; + +struct kb3930 *kb3930_power_off; + +#define EC_GPIO_WAVE 0 +#define EC_GPIO_OFF_MODE 1 + +#define EC_OFF_MODE_REBOOT 0 +#define EC_OFF_MODE_POWER 1 + +static void kb3930_off(struct kb3930 *ddata, int off_mode) +{ + gpiod_direction_output(ddata->off_gpios->desc[EC_GPIO_OFF_MODE], + off_mode); + + /* + * This creates a 10 Hz wave on EC_GPIO_WAVE that signals a + * shutdown request to the EC. Once the EC detects it, it will + * proceed to turn the power off or reset the board depending on + * the value of EC_GPIO_OFF_MODE. + */ + while (1) { + mdelay(50); + gpiod_direction_output(ddata->off_gpios->desc[EC_GPIO_WAVE], 0); + mdelay(50); + gpiod_direction_output(ddata->off_gpios->desc[EC_GPIO_WAVE], 1); + } +} + +static int kb3930_restart(struct notifier_block *this, + unsigned long mode, void *cmd) +{ + kb3930_off(kb3930_power_off, EC_OFF_MODE_REBOOT)