cpufreq: remove s3c24xx drivers

All s3c24xx platforms were removed, so these five drivers are all
obsolete now.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

9 files changed, 0 insertions, 2402 deletions

diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index d514c8e47bad..97acaa2136fd 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -189,84 +189,6 @@ config ARM_RASPBERRYPI_CPUFREQ
 
 	  If in doubt, say N.
 
-config ARM_S3C_CPUFREQ
-	bool
-	help
-	  Internal configuration node for common cpufreq on Samsung SoC
-
-config ARM_S3C24XX_CPUFREQ
-	bool "CPUfreq driver for Samsung S3C24XX series CPUs (EXPERIMENTAL)"
-	depends on ARCH_S3C24XX
-	select ARM_S3C_CPUFREQ
-	help
-	  This enables the CPUfreq driver for the Samsung S3C24XX family
-	  of CPUs.
-
-	  For details, take a look at <file:Documentation/cpu-freq>.
-
-	  If in doubt, say N.
-
-config ARM_S3C24XX_CPUFREQ_DEBUG
-	bool "Debug CPUfreq Samsung driver core"
-	depends on ARM_S3C24XX_CPUFREQ
-	help
-	  Enable s3c_freq_dbg for the Samsung S3C CPUfreq core
-
-config ARM_S3C24XX_CPUFREQ_IODEBUG
-	bool "Debug CPUfreq Samsung driver IO timing"
-	depends on ARM_S3C24XX_CPUFREQ
-	help
-	  Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core
-
-config ARM_S3C24XX_CPUFREQ_DEBUGFS
-	bool "Export debugfs for CPUFreq"
-	depends on ARM_S3C24XX_CPUFREQ && DEBUG_FS
-	help
-	  Export status information via debugfs.
-
-config ARM_S3C2410_CPUFREQ
-	bool
-	depends on ARM_S3C24XX_CPUFREQ && CPU_S3C2410
-	help
-	  CPU Frequency scaling support for S3C2410
-
-config ARM_S3C2412_CPUFREQ
-	bool
-	depends on ARM_S3C24XX_CPUFREQ && CPU_S3C2412
-	default y
-	select S3C2412_IOTIMING
-	help
-	  CPU Frequency scaling support for S3C2412 and S3C2413 SoC CPUs.
-
-config ARM_S3C2416_CPUFREQ
-	bool "S3C2416 CPU Frequency scaling support"
-	depends on CPU_S3C2416
-	help
-	  This adds the CPUFreq driver for the Samsung S3C2416 and
-	  S3C2450 SoC. The S3C2416 supports changing the rate of the
-	  armdiv clock source and also entering a so called dynamic
-	  voltage scaling mode in which it is possible to reduce the
-	  core voltage of the CPU.
-
-	  If in doubt, say N.
-
-config ARM_S3C2416_CPUFREQ_VCORESCALE
-	bool "Allow voltage scaling for S3C2416 arm core"
-	depends on ARM_S3C2416_CPUFREQ && REGULATOR
-	help
-	  Enable CPU voltage scaling when entering the dvs mode.
-	  It uses information gathered through existing hardware and
-	  tests but not documented in any datasheet.
-
-	  If in doubt, say N.
-
-config ARM_S3C2440_CPUFREQ
-	bool "S3C2440/S3C2442 CPU Frequency scaling support"
-	depends on ARM_S3C24XX_CPUFREQ && (CPU_S3C2440 || CPU_S3C2442)
-	default y
-	help
-	  CPU Frequency scaling support for S3C2440 and S3C2442 SoC CPUs.
-
 config ARM_S3C64XX_CPUFREQ
 	bool "Samsung S3C64XX"
 	depends on CPU_S3C6410
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index c62291fcceed..a19842fbd521 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -71,13 +71,7 @@ obj-$(CONFIG_PXA3xx)			+= pxa3xx-cpufreq.o
 obj-$(CONFIG_ARM_QCOM_CPUFREQ_HW)	+= qcom-cpufreq-hw.o
 obj-$(CONFIG_ARM_QCOM_CPUFREQ_NVMEM)	+= qcom-cpufreq-nvmem.o
 obj-$(CONFIG_ARM_RASPBERRYPI_CPUFREQ) 	+= raspberrypi-cpufreq.o
-obj-$(CONFIG_ARM_S3C2410_CPUFREQ)	+= s3c2410-cpufreq.o
-obj-$(CONFIG_ARM_S3C2412_CPUFREQ)	+= s3c2412-cpufreq.o
-obj-$(CONFIG_ARM_S3C2416_CPUFREQ)	+= s3c2416-cpufreq.o
-obj-$(CONFIG_ARM_S3C2440_CPUFREQ)	+= s3c2440-cpufreq.o
 obj-$(CONFIG_ARM_S3C64XX_CPUFREQ)	+= s3c64xx-cpufreq.o
-obj-$(CONFIG_ARM_S3C24XX_CPUFREQ)	+= s3c24xx-cpufreq.o
-obj-$(CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS) += s3c24xx-cpufreq-debugfs.o
 obj-$(CONFIG_ARM_S5PV210_CPUFREQ)	+= s5pv210-cpufreq.o
 obj-$(CONFIG_ARM_SA1110_CPUFREQ)	+= sa1110-cpufreq.o
 obj-$(CONFIG_ARM_SCMI_CPUFREQ)		+= scmi-cpufreq.o
diff --git a/drivers/cpufreq/s3c2410-cpufreq.c b/drivers/cpufreq/s3c2410-cpufreq.c
deleted file mode 100644
index 5dcfbf0bfb74..000000000000
--- a/drivers/cpufreq/s3c2410-cpufreq.c
+++ /dev/null
@@ -1,155 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2006-2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 CPU Frequency scaling
-*/
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include <linux/soc/samsung/s3c-pm.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#define S3C2410_CLKDIVN_PDIVN	     (1<<0)
-#define S3C2410_CLKDIVN_HDIVN	     (1<<1)
-
-/* Note, 2410A has an extra mode for 1:4:4 ratio, bit 2 of CLKDIV */
-
-static void s3c2410_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	u32 clkdiv = 0;
-
-	if (cfg->divs.h_divisor == 2)
-		clkdiv |= S3C2410_CLKDIVN_HDIVN;
-
-	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
-		clkdiv |= S3C2410_CLKDIVN_PDIVN;
-
-	s3c24xx_write_clkdivn(clkdiv);
-}
-
-static int s3c2410_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long hclk, fclk, pclk;
-	unsigned int hdiv, pdiv;
-	unsigned long hclk_max;
-
-	fclk = cfg->freq.fclk;
-	hclk_max = cfg->max.hclk;
-
-	cfg->freq.armclk = fclk;
-
-	s3c_freq_dbg("%s: fclk is %lu, max hclk %lu\n",
-		      __func__, fclk, hclk_max);
-
-	hdiv = (fclk > cfg->max.hclk) ? 2 : 1;
-	hclk = fclk / hdiv;
-
-	if (hclk > cfg->max.hclk) {
-		s3c_freq_dbg("%s: hclk too big\n", __func__);
-		return -EINVAL;
-	}
-
-	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
-	pclk = hclk / pdiv;
-
-	if (pclk > cfg->max.pclk) {
-		s3c_freq_dbg("%s: pclk too big\n", __func__);
-		return -EINVAL;
-	}
-
-	pdiv *= hdiv;
-
-	/* record the result */
-	cfg->divs.p_divisor = pdiv;
-	cfg->divs.h_divisor = hdiv;
-
-	return 0;
-}
-
-static struct s3c_cpufreq_info s3c2410_cpufreq_info = {
-	.max		= {
-		.fclk	= 200000000,
-		.hclk	= 100000000,
-		.pclk	=  50000000,
-	},
-
-	/* transition latency is about 5ms worst-case, so
-	 * set 10ms to be sure */
-	.latency	= 10000000,
-
-	.locktime_m	= 150,
-	.locktime_u	= 150,
-	.locktime_bits	= 12,
-
-	.need_pll	= 1,
-
-	.name		= "s3c2410",
-	.calc_iotiming	= s3c2410_iotiming_calc,
-	.set_iotiming	= s3c2410_iotiming_set,
-	.get_iotiming	= s3c2410_iotiming_get,
-
-	.set_fvco	= s3c2410_set_fvco,
-	.set_refresh	= s3c2410_cpufreq_setrefresh,
-	.set_divs	= s3c2410_cpufreq_setdivs,
-	.calc_divs	= s3c2410_cpufreq_calcdivs,
-
-	.debug_io_show	= s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs),
-};
-
-static int s3c2410_cpufreq_add(struct device *dev,
-			       struct subsys_interface *sif)
-{
-	return s3c_cpufreq_register(&s3c2410_cpufreq_info);
-}
-
-static struct subsys_interface s3c2410_cpufreq_interface = {
-	.name		= "s3c2410_cpufreq",
-	.subsys		= &s3c2410_subsys,
-	.add_dev	= s3c2410_cpufreq_add,
-};
-
-static int __init s3c2410_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2410_cpufreq_interface);
-}
-arch_initcall(s3c2410_cpufreq_init);
-
-static int s3c2410a_cpufreq_add(struct device *dev,
-				struct subsys_interface *sif)
-{
-	/* alter the maximum freq settings for S3C2410A. If a board knows
-	 * it only has a maximum of 200, then it should register its own
-	 * limits. */
-
-	s3c2410_cpufreq_info.max.fclk = 266000000;
-	s3c2410_cpufreq_info.max.hclk = 133000000;
-	s3c2410_cpufreq_info.max.pclk =  66500000;
-	s3c2410_cpufreq_info.name = "s3c2410a";
-
-	return s3c2410_cpufreq_add(dev, sif);
-}
-
-static struct subsys_interface s3c2410a_cpufreq_interface = {
-	.name		= "s3c2410a_cpufreq",
-	.subsys		= &s3c2410a_subsys,
-	.add_dev	= s3c2410a_cpufreq_add,
-};
-
-static int __init s3c2410a_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2410a_cpufreq_interface);
-}
-arch_initcall(s3c2410a_cpufreq_init);
diff --git a/drivers/cpufreq/s3c2412-cpufreq.c b/drivers/cpufreq/s3c2412-cpufreq.c
deleted file mode 100644
index 5945945ead7c..000000000000
--- a/drivers/cpufreq/s3c2412-cpufreq.c
+++ /dev/null
@@ -1,240 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright 2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2412 CPU Frequency scalling
-*/
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include <linux/soc/samsung/s3c-pm.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#define S3C2412_CLKDIVN_PDIVN		(1<<2)
-#define S3C2412_CLKDIVN_HDIVN_MASK	(3<<0)
-#define S3C2412_CLKDIVN_ARMDIVN		(1<<3)
-#define S3C2412_CLKDIVN_DVSEN		(1<<4)
-#define S3C2412_CLKDIVN_HALFHCLK	(1<<5)
-#define S3C2412_CLKDIVN_USB48DIV	(1<<6)
-#define S3C2412_CLKDIVN_UARTDIV_MASK	(15<<8)
-#define S3C2412_CLKDIVN_UARTDIV_SHIFT	(8)
-#define S3C2412_CLKDIVN_I2SDIV_MASK	(15<<12)
-#define S3C2412_CLKDIVN_I2SDIV_SHIFT	(12)
-#define S3C2412_CLKDIVN_CAMDIV_MASK	(15<<16)
-#define S3C2412_CLKDIVN_CAMDIV_SHIFT	(16)
-
-/* our clock resources. */
-static struct clk *xtal;
-static struct clk *fclk;
-static struct clk *hclk;
-static struct clk *armclk;
-
-/* HDIV: 1, 2, 3, 4, 6, 8 */
-
-static int s3c2412_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned int hdiv, pdiv, armdiv, dvs;
-	unsigned long hclk, fclk, armclk, armdiv_clk;
-	unsigned long hclk_max;
-
-	fclk = cfg->freq.fclk;
-	armclk = cfg->freq.armclk;
-	hclk_max = cfg->max.hclk;
-
-	/* We can't run hclk above armclk as at the best we have to
-	 * have armclk and hclk in dvs mode. */
-
-	if (hclk_max > armclk)
-		hclk_max = armclk;
-
-	s3c_freq_dbg("%s: fclk=%lu, armclk=%lu, hclk_max=%lu\n",
-		     __func__, fclk, armclk, hclk_max);
-	s3c_freq_dbg("%s: want f=%lu, arm=%lu, h=%lu, p=%lu\n",
-		     __func__, cfg->freq.fclk, cfg->freq.armclk,
-		     cfg->freq.hclk, cfg->freq.pclk);
-
-	armdiv = fclk / armclk;
-
-	if (armdiv < 1)
-		armdiv = 1;
-	if (armdiv > 2)
-		armdiv = 2;
-
-	cfg->divs.arm_divisor = armdiv;
-	armdiv_clk = fclk / armdiv;
-
-	hdiv = armdiv_clk / hclk_max;
-	if (hdiv < 1)
-		hdiv = 1;
-
-	cfg->freq.hclk = hclk = armdiv_clk / hdiv;
-
-	/* set dvs depending on whether we reached armclk or not. */
-	cfg->divs.dvs = dvs = armclk < armdiv_clk;
-
-	/* update the actual armclk we achieved. */
-	cfg->freq.armclk = dvs ? hclk : armdiv_clk;
-
-	s3c_freq_dbg("%s: armclk %lu, hclk %lu, armdiv %d, hdiv %d, dvs %d\n",
-		     __func__, armclk, hclk, armdiv, hdiv, cfg->divs.dvs);
-
-	if (hdiv > 4)
-		goto invalid;
-
-	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
-
-	if ((hclk / pdiv) > cfg->max.pclk)
-		pdiv++;
-
-	cfg->freq.pclk = hclk / pdiv;
-
-	s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv);
-
-	if (pdiv > 2)
-		goto invalid;
-
-	pdiv *= hdiv;
-
-	/* store the result, and then return */
-
-	cfg->divs.h_divisor = hdiv * armdiv;
-	cfg->divs.p_divisor = pdiv * armdiv;
-
-	return 0;
-
-invalid:
-	return -EINVAL;
-}
-
-static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned long clkdiv;
-	unsigned long olddiv;
-
-	olddiv = clkdiv = s3c24xx_read_clkdivn();
-
-	/* clear off current clock info */
-
-	clkdiv &= ~S3C2412_CLKDIVN_ARMDIVN;
-	clkdiv &= ~S3C2412_CLKDIVN_HDIVN_MASK;
-	clkdiv &= ~S3C2412_CLKDIVN_PDIVN;
-
-	if (cfg->divs.arm_divisor == 2)
-		clkdiv |= S3C2412_CLKDIVN_ARMDIVN;
-
-	clkdiv |= ((cfg->divs.h_divisor / cfg->divs.arm_divisor) - 1);
-
-	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
-		clkdiv |= S3C2412_CLKDIVN_PDIVN;
-
-	s3c_freq_dbg("%s: div %08lx => %08lx\n", __func__, olddiv, clkdiv);
-	s3c24xx_write_clkdivn(clkdiv);
-
-	clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
-}
-
-/* set the default cpu frequency information, based on an 200MHz part
- * as we have no other way of detecting the speed rating in software.
- */
-
-static struct s3c_cpufreq_info s3c2412_cpufreq_info = {
-	.max		= {
-		.fclk	= 200000000,
-		.hclk	= 100000000,
-		.pclk	=  50000000,
-	},
-
-	.latency	= 5000000, /* 5ms */
-
-	.locktime_m	= 150,
-	.locktime_u	= 150,
-	.locktime_bits	= 16,
-
-	.name		= "s3c2412",
-	.set_refresh	= s3c2412_cpufreq_setrefresh,
-	.set_divs	= s3c2412_cpufreq_setdivs,
-	.calc_divs	= s3c2412_cpufreq_calcdivs,
-
-	.calc_iotiming	= s3c2412_iotiming_calc,
-	.set_iotiming	= s3c2412_iotiming_set,
-	.get_iotiming	= s3c2412_iotiming_get,
-
-	.debug_io_show  = s3c_cpufreq_debugfs_call(s3c2412_iotiming_debugfs),
-};
-
-static int s3c2412_cpufreq_add(struct device *dev,
-			       struct subsys_interface *sif)
-{
-	unsigned long fclk_rate;
-
-	hclk = clk_get(NULL, "hclk");
-	if (IS_ERR(hclk)) {
-		pr_err("cannot find hclk clock\n");
-		return -ENOENT;
-	}
-
-	fclk = clk_get(NULL, "fclk");
-	if (IS_ERR(fclk)) {
-		pr_err("cannot find fclk clock\n");
-		goto err_fclk;
-	}
-
-	fclk_rate = clk_get_rate(fclk);
-	if (fclk_rate > 200000000) {
-		pr_info("fclk %ld MHz, assuming 266MHz capable part\n",
-			fclk_rate / 1000000);
-		s3c2412_cpufreq_info.max.fclk = 266000000;
-		s3c2412_cpufreq_info.max.hclk = 133000000;
-		s3c2412_cpufreq_info.max.pclk =  66000000;
-	}
-
-	armclk = clk_get(NULL, "armclk");
-	if (IS_ERR(armclk)) {
-		pr_err("cannot find arm clock\n");
-		goto err_armclk;
-	}
-
-	xtal = clk_get(NULL, "xtal");
-	if (IS_ERR(xtal)) {
-		pr_err("cannot find xtal clock\n");
-		goto err_xtal;
-	}
-
-	return s3c_cpufreq_register(&s3c2412_cpufreq_info);
-
-err_xtal:
-	clk_put(armclk);
-err_armclk:
-	clk_put(fclk);
-err_fclk:
-	clk_put(hclk);
-
-	return -ENOENT;
-}
-
-static struct subsys_interface s3c2412_cpufreq_interface = {
-	.name		= "s3c2412_cpufreq",
-	.subsys		= &s3c2412_subsys,
-	.add_dev	= s3c2412_cpufreq_add,
-};
-
-static int s3c2412_cpufreq_init(void)
-{
-	return subsys_interface_register(&s3c2412_cpufreq_interface);
-}
-arch_initcall(s3c2412_cpufreq_init);
diff --git a/drivers/cpufreq/s3c2416-cpufreq.c b/drivers/cpufreq/s3c2416-cpufreq.c
deleted file mode 100644
index 5c221bc90210..000000000000
--- a/drivers/cpufreq/s3c2416-cpufreq.c
+++ /dev/null
@@ -1,492 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * S3C2416/2450 CPUfreq Support
- *
- * Copyright 2011 Heiko Stuebner <heiko@sntech.de>
- *
- * based on s3c64xx_cpufreq.c
- *
- * Copyright 2009 Wolfson Microelectronics plc
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/cpufreq.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/regulator/consumer.h>
-#include <linux/reboot.h>
-#include <linux/module.h>
-
-static DEFINE_MUTEX(cpufreq_lock);
-
-struct s3c2416_data {
-	struct clk *armdiv;
-	struct clk *armclk;
-	struct clk *hclk;
-
-	unsigned long regulator_latency;
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	struct regulator *vddarm;
-#endif
-
-	struct cpufreq_frequency_table *freq_table;
-
-	bool is_dvs;
-	bool disable_dvs;
-};
-
-static struct s3c2416_data s3c2416_cpufreq;
-
-struct s3c2416_dvfs {
-	unsigned int vddarm_min;
-	unsigned int vddarm_max;
-};
-
-/* pseudo-frequency for dvs mode */
-#define FREQ_DVS	132333
-
-/* frequency to sleep and reboot in
- * it's essential to leave dvs, as some boards do not reconfigure the
- * regulator on reboot
- */
-#define FREQ_SLEEP	133333
-
-/* Sources for the ARMCLK */
-#define SOURCE_HCLK	0
-#define SOURCE_ARMDIV	1
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-/* S3C2416 only supports changing the voltage in the dvs-mode.
- * Voltages down to 1.0V seem to work, so we take what the regulator
- * can get us.
- */
-static struct s3c2416_dvfs s3c2416_dvfs_table[] = {
-	[SOURCE_HCLK] = {  950000, 1250000 },
-	[SOURCE_ARMDIV] = { 1250000, 1350000 },
-};
-#endif
-
-static struct cpufreq_frequency_table s3c2416_freq_table[] = {
-	{ 0, SOURCE_HCLK, FREQ_DVS },
-	{ 0, SOURCE_ARMDIV, 133333 },
-	{ 0, SOURCE_ARMDIV, 266666 },
-	{ 0, SOURCE_ARMDIV, 400000 },
-	{ 0, 0, CPUFREQ_TABLE_END },
-};
-
-static struct cpufreq_frequency_table s3c2450_freq_table[] = {
-	{ 0, SOURCE_HCLK, FREQ_DVS },
-	{ 0, SOURCE_ARMDIV, 133500 },
-	{ 0, SOURCE_ARMDIV, 267000 },
-	{ 0, SOURCE_ARMDIV, 534000 },
-	{ 0, 0, CPUFREQ_TABLE_END },
-};
-
-static unsigned int s3c2416_cpufreq_get_speed(unsigned int cpu)
-{
-	struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
-
-	if (cpu != 0)
-		return 0;
-
-	/* return our pseudo-frequency when in dvs mode */
-	if (s3c_freq->is_dvs)
-		return FREQ_DVS;
-
-	return clk_get_rate(s3c_freq->armclk) / 1000;
-}
-
-static int s3c2416_cpufreq_set_armdiv(struct s3c2416_data *s3c_freq,
-				      unsigned int freq)
-{
-	int ret;
-
-	if (clk_get_rate(s3c_freq->armdiv) / 1000 != freq) {
-		ret = clk_set_rate(s3c_freq->armdiv, freq * 1000);
-		if (ret < 0) {
-			pr_err("cpufreq: Failed to set armdiv rate %dkHz: %d\n",
-			       freq, ret);
-			return ret;
-		}
-	}
-
-	return 0;
-}
-
-static int s3c2416_cpufreq_enter_dvs(struct s3c2416_data *s3c_freq, int idx)
-{
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	struct s3c2416_dvfs *dvfs;
-#endif
-	int ret;
-
-	if (s3c_freq->is_dvs) {
-		pr_debug("cpufreq: already in dvs mode, nothing to do\n");
-		return 0;
-	}
-
-	pr_debug("cpufreq: switching armclk to hclk (%lukHz)\n",
-		 clk_get_rate(s3c_freq->hclk) / 1000);
-	ret = clk_set_parent(s3c_freq->armclk, s3c_freq->hclk);
-	if (ret < 0) {
-		pr_err("cpufreq: Failed to switch armclk to hclk: %d\n", ret);
-		return ret;
-	}
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	/* changing the core voltage is only allowed when in dvs mode */
-	if (s3c_freq->vddarm) {
-		dvfs = &s3c2416_dvfs_table[idx];
-
-		pr_debug("cpufreq: setting regulator to %d-%d\n",
-			 dvfs->vddarm_min, dvfs->vddarm_max);
-		ret = regulator_set_voltage(s3c_freq->vddarm,
-					    dvfs->vddarm_min,
-					    dvfs->vddarm_max);
-
-		/* when lowering the voltage failed, there is nothing to do */
-		if (ret != 0)
-			pr_err("cpufreq: Failed to set VDDARM: %d\n", ret);
-	}
-#endif
-
-	s3c_freq->is_dvs = 1;
-
-	return 0;
-}
-
-static int s3c2416_cpufreq_leave_dvs(struct s3c2416_data *s3c_freq, int idx)
-{
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	struct s3c2416_dvfs *dvfs;
-#endif
-	int ret;
-
-	if (!s3c_freq->is_dvs) {
-		pr_debug("cpufreq: not in dvs mode, so can't leave\n");
-		return 0;
-	}
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	if (s3c_freq->vddarm) {
-		dvfs = &s3c2416_dvfs_table[idx];
-
-		pr_debug("cpufreq: setting regulator to %d-%d\n",
-			 dvfs->vddarm_min, dvfs->vddarm_max);
-		ret = regulator_set_voltage(s3c_freq->vddarm,
-					    dvfs->vddarm_min,
-					    dvfs->vddarm_max);
-		if (ret != 0) {
-			pr_err("cpufreq: Failed to set VDDARM: %d\n", ret);
-			return ret;
-		}
-	}
-#endif
-
-	/* force armdiv to hclk frequency for transition from dvs*/
-	if (clk_get_rate(s3c_freq->armdiv) > clk_get_rate(s3c_freq->hclk)) {
-		pr_debug("cpufreq: force armdiv to hclk frequency (%lukHz)\n",
-			 clk_get_rate(s3c_freq->hclk) / 1000);
-		ret = s3c2416_cpufreq_set_armdiv(s3c_freq,
-					clk_get_rate(s3c_freq->hclk) / 1000);
-		if (ret < 0) {
-			pr_err("cpufreq: Failed to set the armdiv to %lukHz: %d\n",
-			       clk_get_rate(s3c_freq->hclk) / 1000, ret);
-			return ret;
-		}
-	}
-
-	pr_debug("cpufreq: switching armclk parent to armdiv (%lukHz)\n",
-			clk_get_rate(s3c_freq->armdiv) / 1000);
-
-	ret = clk_set_parent(s3c_freq->armclk, s3c_freq->armdiv);
-	if (ret < 0) {
-		pr_err("cpufreq: Failed to switch armclk clock parent to armdiv: %d\n",
-		       ret);
-		return ret;
-	}
-
-	s3c_freq->is_dvs = 0;
-
-	return 0;
-}
-
-static int s3c2416_cpufreq_set_target(struct cpufreq_policy *policy,
-				      unsigned int index)
-{
-	struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
-	unsigned int new_freq;
-	int idx, ret, to_dvs = 0;
-
-	mutex_lock(&cpufreq_lock);
-
-	idx = s3c_freq->freq_table[index].driver_data;
-
-	if (idx == SOURCE_HCLK)
-		to_dvs = 1;
-
-	/* switching to dvs when it's not allowed */
-	if (to_dvs && s3c_freq->disable_dvs) {
-		pr_debug("cpufreq: entering dvs mode not allowed\n");
-		ret = -EINVAL;
-		goto out;
-	}
-
-	/* When leavin dvs mode, always switch the armdiv to the hclk rate
-	 * The S3C2416 has stability issues when switching directly to
-	 * higher frequencies.
-	 */
-	new_freq = (s3c_freq->is_dvs && !to_dvs)
-				? clk_get_rate(s3c_freq->hclk) / 1000
-				: s3c_freq->freq_table[index].frequency;
-
-	if (to_dvs) {
-		pr_debug("cpufreq: enter dvs\n");
-		ret = s3c2416_cpufreq_enter_dvs(s3c_freq, idx);
-	} else if (s3c_freq->is_dvs) {
-		pr_debug("cpufreq: leave dvs\n");
-		ret = s3c2416_cpufreq_leave_dvs(s3c_freq, idx);
-	} else {
-		pr_debug("cpufreq: change armdiv to %dkHz\n", new_freq);
-		ret = s3c2416_cpufreq_set_armdiv(s3c_freq, new_freq);
-	}
-
-out:
-	mutex_unlock(&cpufreq_lock);
-
-	return ret;
-}
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-static void s3c2416_cpufreq_cfg_regulator(struct s3c2416_data *s3c_freq)
-{
-	int count, v, i, found;
-	struct cpufreq_frequency_table *pos;
-	struct s3c2416_dvfs *dvfs;
-
-	count = regulator_count_voltages(s3c_freq->vddarm);
-	if (count < 0) {
-		pr_err("cpufreq: Unable to check supported voltages\n");
-		return;
-	}
-
-	if (!count)
-		goto out;
-
-	cpufreq_for_each_valid_entry(pos, s3c_freq->freq_table) {
-		dvfs = &s3c2416_dvfs_table[pos->driver_data];
-		found = 0;
-
-		/* Check only the min-voltage, more is always ok on S3C2416 */
-		for (i = 0; i < count; i++) {
-			v = regulator_list_voltage(s3c_freq->vddarm, i);
-			if (v >= dvfs->vddarm_min)
-				found = 1;
-		}
-
-		if (!found) {
-			pr_debug("cpufreq: %dkHz unsupported by regulator\n",
-				 pos->frequency);
-			pos->frequency = CPUFREQ_ENTRY_INVALID;
-		}
-	}
-
-out:
-	/* Guessed */
-	s3c_freq->regulator_latency = 1 * 1000 * 1000;
-}
-#endif
-
-static int s3c2416_cpufreq_reboot_notifier_evt(struct notifier_block *this,
-					       unsigned long event, void *ptr)
-{
-	struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
-	int ret;
-	struct cpufreq_policy *policy;
-
-	mutex_lock(&cpufreq_lock);
-
-	/* disable further changes */
-	s3c_freq->disable_dvs = 1;
-
-	mutex_unlock(&cpufreq_lock);
-
-	/* some boards don't reconfigure the regulator on reboot, which
-	 * could lead to undervolting the cpu when the clock is reset.
-	 * Therefore we always leave the DVS mode on reboot.
-	 */
-	if (s3c_freq->is_dvs) {
-		pr_debug("cpufreq: leave dvs on reboot\n");
-
-		policy = cpufreq_cpu_get(0);
-		if (!policy) {
-			pr_debug("cpufreq: get no policy for cpu0\n");
-			return NOTIFY_BAD;
-		}
-
-		ret = cpufreq_driver_target(policy, FREQ_SLEEP, 0);
-		cpufreq_cpu_put(policy);
-
-		if (ret < 0)
-			return NOTIFY_BAD;
-	}
-
-	return NOTIFY_DONE;
-}
-
-static struct notifier_block s3c2416_cpufreq_reboot_notifier = {
-	.notifier_call = s3c2416_cpufreq_reboot_notifier_evt,
-};
-
-static int s3c2416_cpufreq_driver_init(struct cpufreq_policy *policy)
-{
-	struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
-	struct cpufreq_frequency_table *pos;
-	struct clk *msysclk;
-	unsigned long rate;
-	int ret;
-
-	if (policy->cpu != 0)
-		return -EINVAL;
-
-	msysclk = clk_get(NULL, "msysclk");
-	if (IS_ERR(msysclk)) {
-		ret = PTR_ERR(msysclk);
-		pr_err("cpufreq: Unable to obtain msysclk: %d\n", ret);
-		return ret;
-	}
-
-	/*
-	 * S3C2416 and S3C2450 share the same processor-ID and also provide no
-	 * other means to distinguish them other than through the rate of
-	 * msysclk. On S3C2416 msysclk runs at 800MHz and on S3C2450 at 533MHz.
-	 */
-	rate = clk_get_rate(msysclk);
-	if (rate == 800 * 1000 * 1000) {
-		pr_info("cpufreq: msysclk running at %lukHz, using S3C2416 frequency table\n",
-			rate / 1000);
-		s3c_freq->freq_table = s3c2416_freq_table;
-		policy->cpuinfo.max_freq = 400000;
-	} else if (rate / 1000 == 534000) {
-		pr_info("cpufreq: msysclk running at %lukHz, using S3C2450 frequency table\n",
-			rate / 1000);
-		s3c_freq->freq_table = s3c2450_freq_table;
-		policy->cpuinfo.max_freq = 534000;
-	}
-
-	/* not needed anymore */
-	clk_put(msysclk);
-
-	if (s3c_freq->freq_table == NULL) {
-		pr_err("cpufreq: No frequency information for this CPU, msysclk at %lukHz\n",
-		       rate / 1000);
-		return -ENODEV;
-	}
-
-	s3c_freq->is_dvs = 0;
-
-	s3c_freq->armdiv = clk_get(NULL, "armdiv");
-	if (IS_ERR(s3c_freq->armdiv)) {
-		ret = PTR_ERR(s3c_freq->armdiv);
-		pr_err("cpufreq: Unable to obtain ARMDIV: %d\n", ret);
-		return ret;
-	}
-
-	s3c_freq->hclk = clk_get(NULL, "hclk");
-	if (IS_ERR(s3c_freq->hclk)) {
-		ret = PTR_ERR(s3c_freq->hclk);
-		pr_err("cpufreq: Unable to obtain HCLK: %d\n", ret);
-		goto err_hclk;
-	}
-
-	/* chech hclk rate, we only support the common 133MHz for now
-	 * hclk could also run at 66MHz, but this not often used
-	 */
-	rate = clk_get_rate(s3c_freq->hclk);
-	if (rate < 133 * 1000 * 1000) {
-		pr_err("cpufreq: HCLK not at 133MHz\n");
-		ret = -EINVAL;
-		goto err_armclk;
-	}
-
-	s3c_freq->armclk = clk_get(NULL, "armclk");
-	if (IS_ERR(s3c_freq->armclk)) {
-		ret = PTR_ERR(s3c_freq->armclk);
-		pr_err("cpufreq: Unable to obtain ARMCLK: %d\n", ret);
-		goto err_armclk;
-	}
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-	s3c_freq->vddarm = regulator_get(NULL, "vddarm");
-	if (IS_ERR(s3c_freq->vddarm)) {
-		ret = PTR_ERR(s3c_freq->vddarm);
-		pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret);
-		goto err_vddarm;
-	}
-
-	s3c2416_cpufreq_cfg_regulator(s3c_freq);
-#else
-	s3c_freq->regulator_latency = 0;
-#endif
-
-	cpufreq_for_each_entry(pos, s3c_freq->freq_table) {
-		/* special handling for dvs mode */
-		if (pos->driver_data == 0) {
-			if (!s3c_freq->hclk) {
-				pr_debug("cpufreq: %dkHz unsupported as it would need unavailable dvs mode\n",
-					 pos->frequency);
-				pos->frequency = CPUFREQ_ENTRY_INVALID;
-			} else {
-				continue;
-			}
-		}
-
-		/* Check for frequencies we can generate */
-		rate = clk_round_rate(s3c_freq->armdiv,
-				      pos->frequency * 1000);
-		rate /= 1000;
-		if (rate != pos->frequency) {
-			pr_debug("cpufreq: %dkHz unsupported by clock (clk_round_rate return %lu)\n",
-				pos->frequency, rate);
-			pos->frequency = CPUFREQ_ENTRY_INVALID;
-		}
-	}
-
-	/* Datasheet says PLL stabalisation time must be at least 300us,
-	 * so but add some fudge. (reference in LOCKCON0 register description)
-	 */
-	cpufreq_generic_init(policy, s3c_freq->freq_table,
-			(500 * 1000) + s3c_freq->regulator_latency);
-	register_reboot_notifier(&s3c2416_cpufreq_reboot_notifier);
-
-	return 0;
-
-#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
-err_vddarm:
-	clk_put(s3c_freq->armclk);
-#endif
-err_armclk:
-	clk_put(s3c_freq->hclk);
-err_hclk:
-	clk_put(s3c_freq->armdiv);
-
-	return ret;
-}
-
-static struct cpufreq_driver s3c2416_cpufreq_driver = {
-	.flags		= CPUFREQ_NEED_INITIAL_FREQ_CHECK,
-	.verify		= cpufreq_generic_frequency_table_verify,
-	.target_index	= s3c2416_cpufreq_set_target,
-	.get		= s3c2416_cpufreq_get_speed,
-	.init		= s3c2416_cpufreq_driver_init,
-	.name		= "s3c2416",
-	.attr		= cpufreq_generic_attr,
-};
-
-static int __init s3c2416_cpufreq_init(void)
-{
-	return cpufreq_register_driver(&s3c2416_cpufreq_driver);
-}
-module_init(s3c2416_cpufreq_init);
diff --git a/drivers/cpufreq/s3c2440-cpufreq.c b/drivers/cpufreq/s3c2440-cpufreq.c
deleted file mode 100644
index 2011fb9c03a4..000000000000
--- a/drivers/cpufreq/s3c2440-cpufreq.c
+++ /dev/null
@@ -1,321 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2006-2009 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *	Ben Dooks <ben@simtec.co.uk>
- *	Vincent Sanders <vince@simtec.co.uk>
- *
- * S3C2440/S3C2442 CPU Frequency scaling
-*/
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/cpufreq.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/soc/samsung/s3c-cpufreq-core.h>
-#include <linux/soc/samsung/s3c-pm.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#define S3C2440_CLKDIVN_PDIVN	     (1<<0)
-#define S3C2440_CLKDIVN_HDIVN_MASK   (3<<1)
-#define S3C2440_CLKDIVN_HDIVN_1      (0<<1)
-#define S3C2440_CLKDIVN_HDIVN_2      (1<<1)
-#define S3C2440_CLKDIVN_HDIVN_4_8    (2<<1)
-#define S3C2440_CLKDIVN_HDIVN_3_6    (3<<1)
-#define S3C2440_CLKDIVN_UCLK         (1<<3)
-
-#define S3C2440_CAMDIVN_CAMCLK_MASK  (0xf<<0)
-#define S3C2440_CAMDIVN_CAMCLK_SEL   (1<<4)
-#define S3C2440_CAMDIVN_HCLK3_HALF   (1<<8)
-#define S3C2440_CAMDIVN_HCLK4_HALF   (1<<9)
-#define S3C2440_CAMDIVN_DVSEN        (1<<12)
-
-#define S3C2442_CAMDIVN_CAMCLK_DIV3  (1<<5)
-
-static struct clk *xtal;
-static struct clk *fclk;
-static struct clk *hclk;
-static struct clk *armclk;
-
-/* HDIV: 1, 2, 3, 4, 6, 8 */
-
-static inline int within_khz(unsigned long a, unsigned long b)
-{
-	long diff = a - b;
-
-	return (diff >= -1000 && diff <= 1000);
-}
-
-/**
- * s3c2440_cpufreq_calcdivs - calculate divider settings
- * @cfg: The cpu frequency settings.
- *
- * Calcualte the divider values for the given frequency settings
- * specified in @cfg. The values are stored in @cfg for later use
- * by the relevant set routine if the request settings can be reached.
- */
-static int s3c2440_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
-{
-	unsigned int hdiv, pdiv;
-	unsigned l