Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd

Pull MTD updates from Boris Brezillon:
 "MTD core changes:
   - Rework core functions to avoid duplicating generic checks in
     NAND/OneNAND sub-layers
   - Update the MAINTAINERS entry to reflect the fact that MTD
     maintainers now use a single git tree

  MTD driver changes:
   - CFI: use macros instead of inline functions to limit stack usage
     and make KASAN happy

  NAND core changes:
   - Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
   - Introduce the ->exec_op() infrastructure
   - Rework NAND buffers handling
   - Fix ECC requirements for K9F4G08U0D
   - Fix nand_do_read_oob() to return the number of bitflips
   - Mark K9F1G08U0E as not supporting subpage writes

  NAND driver changes:
   - MTK: Rework the driver to support new IP versions
   - OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
     fix DT support
   - Marvell: Add a new driver to replace the pxa3xx one

  SPI NOR core changes:
   - Add support to new ISSI and Cypress/Spansion memory parts.
   - Fix support of Micron memories by checking error bits in the FSR.
   - Fix update of block-protection bits by reading back the SR.
   - Restore the internal state of the SPI flash memory when removing
     the device.

  SPI NOR driver changes:
   - Maintenance for Freescale, Intel and Metiatek drivers.
   - Add support of the direct access mode for the Cadence QSPI
     controller"

* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
  mtd: nand: sunxi: Fix ECC strength choice
  mtd: nand: gpmi: Fix subpage reads
  mtd: nand: Fix build issues due to an anonymous union
  mtd: nand: marvell: Fix missing memory allocation modifier
  mtd: nand: marvell: remove redundant variable 'oob_len'
  mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
  mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
  mtd: Remove duplicate checks on mtd_oob_ops parameter
  mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
  mtd: mtdpart: Make ECC stat handling consistent
  mtd: onenand: omap2: print resource using %pR format string
  mtd: mtk-nor: modify functions' name more generally
  mtd: onenand: samsung: remove incorrect __iomem annotation
  MAINTAINERS: Add entry for Marvell NAND controller driver
  ARM: OMAP2+: Remove gpmc-onenand
  mtd: onenand: omap2: Configure driver from DT
  mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
  mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
  mtd: onenand: omap2: Convert to use dmaengine for memcpy
  mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
  ...

82 files changed, 6866 insertions, 2443 deletions

diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
index c34aa6f8a424..63d4d626fbd5 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -12,7 +12,7 @@ Required properties:
   - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
   - interrupts : Should contain the interrupt for the device
   - clocks : The clocks needed by the QuadSPI controller
-  - clock-names : the name of the clocks
+  - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
 
 Optional properties:
   - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
index b6e8bfd024f4..e9f01a963a0a 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
@@ -9,13 +9,14 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 
+ - compatible:		"ti,omap2-onenand"
  - reg:			The CS line the peripheral is connected to
- - gpmc,device-width	Width of the ONENAND device connected to the GPMC
+ - gpmc,device-width:	Width of the ONENAND device connected to the GPMC
 			in bytes. Must be 1 or 2.
 
 Optional properties:
 
- - dma-channel:		DMA Channel index
+ - int-gpios:		GPIO specifier for the INT pin.
 
 For inline partition table parsing (optional):
 
@@ -35,6 +36,7 @@ Example for an OMAP3430 board:
 		#size-cells = <1>;
 
 		onenand@0 {
+			compatible = "ti,omap2-onenand";
 			reg = <0 0 0>; /* CS0, offset 0 */
 			gpmc,device-width = <2>;
 
diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt
new file mode 100644
index 000000000000..c08fb477b3c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/marvell-nand.txt
@@ -0,0 +1,123 @@
+Marvell NAND Flash Controller (NFC)
+
+Required properties:
+- compatible: can be one of the following:
+    * "marvell,armada-8k-nand-controller"
+    * "marvell,armada370-nand-controller"
+    * "marvell,pxa3xx-nand-controller"
+    * "marvell,armada-8k-nand" (deprecated)
+    * "marvell,armada370-nand" (deprecated)
+    * "marvell,pxa3xx-nand" (deprecated)
+  Compatibles marked deprecated support only the old bindings described
+  at the bottom.
+- reg: NAND flash controller memory area.
+- #address-cells: shall be set to 1. Encode the NAND CS.
+- #size-cells: shall be set to 0.
+- interrupts: shall define the NAND controller interrupt.
+- clocks: shall reference the NAND controller clock.
+- marvell,system-controller: Set to retrieve the syscon node that handles
+  NAND controller related registers (only required with the
+  "marvell,armada-8k-nand[-controller]" compatibles).
+
+Optional properties:
+- label: see partition.txt. New platforms shall omit this property.
+- dmas: shall reference DMA channel associated to the NAND controller.
+  This property is only used with "marvell,pxa3xx-nand[-controller]"
+  compatible strings.
+- dma-names: shall be "rxtx".
+  This property is only used with "marvell,pxa3xx-nand[-controller]"
+  compatible strings.
+
+Optional children nodes:
+Children nodes represent the available NAND chips.
+
+Required properties:
+- reg: shall contain the native Chip Select ids (0-3).
+- nand-rb: see nand.txt (0-1).
+
+Optional properties:
+- marvell,nand-keep-config: orders the driver not to take the timings
+  from the core and leaving them completely untouched. Bootloader
+  timings will then be used.
+- label: MTD name.
+- nand-on-flash-bbt: see nand.txt.
+- nand-ecc-mode: see nand.txt. Will use hardware ECC if not specified.
+- nand-ecc-algo: see nand.txt. This property is essentially useful when
+  not using hardware ECC. Howerver, it may be added when using hardware
+  ECC for clarification but will be ignored by the driver because ECC
+  mode is chosen depending on the page size and the strength required by
+  the NAND chip. This value may be overwritten with nand-ecc-strength
+  property.
+- nand-ecc-strength: see nand.txt.
+- nand-ecc-step-size: see nand.txt. Marvell's NAND flash controller does
+  use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual
+  step size will shrink or grow in order to fit the required strength.
+  Step sizes are not completely random for all and follow certain
+  patterns described in AN-379, "Marvell SoC NFC ECC".
+
+See Documentation/devicetree/bindings/mtd/nand.txt for more details on
+generic bindings.
+
+
+Example:
+nand_controller: nand-controller@d0000 {
+	compatible = "marvell,armada370-nand-controller";
+	reg = <0xd0000 0x54>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&coredivclk 0>;
+
+	nand@0 {
+		reg = <0>;
+		label = "main-storage";
+		nand-rb = <0>;
+		nand-ecc-mode = "hw";
+		marvell,nand-keep-config;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Rootfs";
+				reg = <0x00000000 0x40000000>;
+			};
+		};
+	};
+};
+
+
+Note on legacy bindings: One can find, in not-updated device trees,
+bindings slightly different than described above with other properties
+described below as well as the partitions node at the root of a so
+called "nand" node (without clear controller/chip separation).
+
+Legacy properties:
+- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly
+  used it, this bit was set by the bootloader for many boards and even if
+  it is marked reserved in several datasheets, it might be needed to set
+  it (otherwise it is harmless) so whether or not this property is set,
+  the bit is selected by the driver.
+- num-cs: Number of chip-select lines to use, all boards blindly set 1
+  to this and for a reason, other values would have failed. The value of
+  this property is ignored.
+
+Example:
+
+	nand0: nand@43100000 {
+		compatible = "marvell,pxa3xx-nand";
+		reg = <0x43100000 90>;
+		interrupts = <45>;
+		dmas = <&pdma 97 0>;
+		dma-names = "rxtx";
+		#address-cells = <1>;
+		marvell,nand-keep-config;
+		marvell,nand-enable-arbiter;
+		num-cs = <1>;
+		/* Partitions (optional) */
+       };
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
index 0431841de781..1c88526dedfc 100644
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
@@ -12,8 +12,10 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be one of "mediatek,mt2701-nfc",
-				"mediatek,mt2712-nfc".
+- compatible:			Should be one of
+				"mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc",
+				"mediatek,mt7622-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -142,7 +144,10 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
+- compatible:	Should be one of
+		"mediatek,mt2701-ecc",
+		"mediatek,mt2712-ecc",
+		"mediatek,mt7622-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.
diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index 133f3813719c..8bb11d809429 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -43,6 +43,7 @@ Optional NAND chip properties:
 		     This is particularly useful when only the in-band area is
 		     used by the upper layers, and you want to make your NAND
 		     as reliable as possible.
+- nand-rb: shall contain the native Ready/Busy ids.
 
 The ECC strength and ECC step size properties define the correction capability
 of a controller. Together, they say a controller can correct "{strength} bit
diff --git a/Documentation/mtd/spi-nor.txt b/Documentation/mtd/spi-nor.txt
index 548d6306ebca..da1fbff5a24c 100644
--- a/Documentation/mtd/spi-nor.txt
+++ b/Documentation/mtd/spi-nor.txt
@@ -60,3 +60,6 @@ The main API is spi_nor_scan(). Before you call the hook, a driver should
 initialize the necessary fields for spi_nor{}. Please see
 drivers/mtd/spi-nor/spi-nor.c for detail. Please also refer to fsl-quadspi.c
 when you want to write a new driver for a SPI NOR controller.
+Another API is spi_nor_restore(), this is used to restore the status of SPI
+flash chip such as addressing mode. Call it whenever detach the driver from
+device or reboot the system.
diff --git a/MAINTAINERS b/MAINTAINERS
index 2f0e8d927185..0b5249149695 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2392,13 +2392,6 @@ F:	Documentation/devicetree/bindings/input/atmel,maxtouch.txt
 F:	drivers/input/touchscreen/atmel_mxt_ts.c
 F:	include/linux/platform_data/atmel_mxt_ts.h
 
-ATMEL NAND DRIVER
-M:	Wenyou Yang <wenyou.yang@atmel.com>
-M:	Josh Wu <rainyfeeling@outlook.com>
-L:	linux-mtd@lists.infradead.org
-S:	Supported
-F:	drivers/mtd/nand/atmel/*
-
 ATMEL SAMA5D2 ADC DRIVER
 M:	Ludovic Desroches <ludovic.desroches@microchip.com>
 L:	linux-iio@vger.kernel.org
@@ -8406,6 +8399,13 @@ L:	linux-wireless@vger.kernel.org
 S:	Odd Fixes
 F:	drivers/net/wireless/marvell/mwl8k.c
 
+MARVELL NAND CONTROLLER DRIVER
+M:	Miquel Raynal <miquel.raynal@free-electrons.com>
+L:	linux-mtd@lists.infradead.org
+S:	Maintained
+F:	drivers/mtd/nand/marvell_nand.c
+F:	Documentation/devicetree/bindings/mtd/marvell-nand.txt
+
 MARVELL SOC MMC/SD/SDIO CONTROLLER DRIVER
 M:	Nicolas Pitre <nico@fluxnic.net>
 S:	Odd Fixes
@@ -8953,7 +8953,7 @@ L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/
 Q:	http://patchwork.ozlabs.org/project/linux-mtd/list/
 T:	git git://git.infradead.org/linux-mtd.git master
-T:	git git://git.infradead.org/l2-mtd.git master
+T:	git git://git.infradead.org/linux-mtd.git mtd/next
 S:	Maintained
 F:	Documentation/devicetree/bindings/mtd/
 F:	drivers/mtd/
@@ -9042,6 +9042,14 @@ F:	drivers/media/platform/atmel/atmel-isc.c
 F:	drivers/media/platform/atmel/atmel-isc-regs.h
 F:	devicetree/bindings/media/atmel-isc.txt
 
+MICROCHIP / ATMEL NAND DRIVER
+M:	Wenyou Yang <wenyou.yang@microchip.com>
+M:	Josh Wu <rainyfeeling@outlook.com>
+L:	linux-mtd@lists.infradead.org
+S:	Supported
+F:	drivers/mtd/nand/atmel/*
+F:	Documentation/devicetree/bindings/mtd/atmel-nand.txt
+
 MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER
 M:	Woojung Huh <Woojung.Huh@microchip.com>
 M:	Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
@@ -9342,7 +9350,7 @@ L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/
 Q:	http://patchwork.ozlabs.org/project/linux-mtd/list/
 T:	git git://git.infradead.org/linux-mtd.git nand/fixes
-T:	git git://git.infradead.org/l2-mtd.git nand/next
+T:	git git://git.infradead.org/linux-mtd.git nand/next
 S:	Maintained
 F:	drivers/mtd/nand/
 F:	include/linux/mtd/*nand*.h
@@ -12787,7 +12795,7 @@ L:	linux-mtd@lists.infradead.org
 W:	http://www.linux-mtd.infradead.org/
 Q:	http://patchwork.ozlabs.org/project/linux-mtd/list/
 T:	git git://git.infradead.org/linux-mtd.git spi-nor/fixes
-T:	git git://git.infradead.org/l2-mtd.git spi-nor/next
+T:	git git://git.infradead.org/linux-mtd.git spi-nor/next
 S:	Maintained
 F:	drivers/mtd/spi-nor/
 F:	include/linux/mtd/spi-nor.h
diff --git a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi
index 1df3ace3af92..63b0b4921e4e 100644
--- a/arch/arm/boot/dts/omap2420-n8x0-common.dtsi
+++ b/arch/arm/boot/dts/omap2420-n8x0-common.dtsi
@@ -52,6 +52,7 @@
 	onenand@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
+		compatible = "ti,omap2-onenand";
 		reg = <0 0 0x20000>;	/* CS0, offset 0, IO size 128K */
 
 		gpmc,sync-read;
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 4ad7d5565906..f33cc80c9dbc 100644
--- a/