Merge tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
   - Add new ioctl to allow userspace to send multi commands
   - Wait for card busy signalling before starting SDIO requests
   - Remove MMC_CLKGATE
   - Enable tuning for DDR50 mode
   - Some code clean-up/improvements to mmc pwrseq
   - Use highest priority for eMMC restart handler
   - Add DT bindings for eMMC hardware reset support
   - Extend the mmc_send_tuning() API
   - Improve ios show for debugfs
   - A couple of code optimizations

  MMC host:
   - Some generic OF improvements
   - Various code clean-ups
   - sirf: Add support for DDR50
   - sunxi: Add support for card busy detection
   - mediatek: Use MMC_CAP_RUNTIME_RESUME
   - mediatek: Add support for eMMC HW-reset
   - mediatek: Add support for HS400
   - dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
   - dw_mmc: Add external DMA interface support
   - dw_mmc: Some various improvements
   - dw_mmc-rockchip: MMC tuning with the clock phase framework
   - sdhci: Properly clear IRQs during resume
   - sdhci: Enable tuning for DDR50 mode
   - sdhci-of-esdhc: Use IRQ mode for card detection
   - sdhci-of-esdhc: Support both BE and LE host controller
   - sdhci-pci: Build o2micro support in the same module
   - sdhci-pci: Support for new Intel host controllers
   - sdhci-acpi: Support for new Intel host controllers"

* tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc: (73 commits)
  mmc: dw_mmc: fix the wrong setting for UHS-DDR50 mode
  mmc: dw_mmc: fix the CardThreshold boundary at CardThrCtl register
  mmc: dw_mmc: NULL dereference in error message
  mmc: pwrseq: Use highest priority for eMMC restart handler
  mmc: mediatek: add HS400 support
  mmc: mmc: extend the mmc_send_tuning()
  mmc: mediatek: add implement of ops->hw_reset()
  mmc: mediatek: fix got GPD checksum error interrupt when data transfer
  mmc: mediatek: change the argument "ddr" to "timing"
  mmc: mediatek: make cmd_ints_mask to const
  mmc: dt-bindings: update Mediatek MMC bindings
  mmc: core: Add DT bindings for eMMC hardware reset support
  mmc: omap_hsmmc: Enable omap_hsmmc for Keystone 2
  mmc: sdhci-acpi: Add more ACPI HIDs for Intel controllers
  mmc: sdhci-pci: Add more PCI IDs for Intel controllers
  arm: lpc18xx_defconfig: remove CONFIG_MMC_DW_IDMAC
  arm: hisi_defconfig: remove CONFIG_MMC_DW_IDMAC
  arm: exynos_defconfig: remove CONFIG_MMC_DW_IDMAC
  arc: axs10x_defconfig: remove CONFIG_MMC_DW_IDMAC
  mips: pistachio_defconfig: remove CONFIG_MMC_DW_IDMAC
  ...

67 files changed, 1703 insertions, 910 deletions

diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
index b7943f3f9995..dedfb02c744a 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
@@ -22,6 +22,8 @@ Optional properties:
   - voltage-ranges : two cells are required, first cell specifies minimum
     slot voltage (mV), second cell specifies maximum slot voltage (mV).
     Several ranges could be specified.
+  - little-endian : If the host controller is little-endian mode, specify
+    this property. The default endian mode is big-endian.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
index 0384fc3f64e8..f693baf87264 100644
--- a/Documentation/devicetree/bindings/mmc/mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -37,6 +37,7 @@ Optional properties:
 - sd-uhs-sdr104: SD UHS SDR104 speed is supported
 - sd-uhs-ddr50: SD UHS DDR50 speed is supported
 - cap-power-off-card: powering off the card is safe
+- cap-mmc-hw-reset: eMMC hardware reset is supported
 - cap-sdio-irq: enable SDIO IRQ signalling on this interface
 - full-pwr-cycle: full power cycle of the card is supported
 - mmc-ddr-1_8v: eMMC high-speed DDR mode(1.8V I/O) is supported
diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
index a1adfa495ad3..0120c7f1109c 100644
--- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
+++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
@@ -17,6 +17,11 @@ Required properties:
 - vmmc-supply: power to the Core
 - vqmmc-supply: power to the IO
 
+Optional properties:
+- assigned-clocks: PLL of the source clock
+- assigned-clock-parents: parent of source clock, used for HS400 mode to get 400Mhz source clock
+- hs400-ds-delay: HS400 DS delay setting
+
 Examples:
 mmc0: mmc@11230000 {
 	compatible = "mediatek,mt8173-mmc", "mediatek,mt8135-mmc";
@@ -24,9 +29,13 @@ mmc0: mmc@11230000 {
 	interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_LOW>;
 	vmmc-supply = <&mt6397_vemc_3v3_reg>;
 	vqmmc-supply = <&mt6397_vio18_reg>;
-	clocks = <&pericfg CLK_PERI_MSDC30_0>, <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
+	clocks = <&pericfg CLK_PERI_MSDC30_0>,
+	         <&topckgen CLK_TOP_MSDC50_0_H_SEL>;
 	clock-names = "source", "hclk";
 	pinctrl-names = "default", "state_uhs";
 	pinctrl-0 = <&mmc0_pins_default>;
 	pinctrl-1 = <&mmc0_pins_uhs>;
+	assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
+	assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+	hs400-ds-delay = <0x14015>;
 };
diff --git a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
index d38942f6c5ae..cae29eb5733d 100644
--- a/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
+++ b/Documentation/devicetree/bindings/mmc/renesas,mmcif.txt
@@ -6,11 +6,12 @@ and the properties used by the MMCIF device.
 
 Required properties:
 
-- compatible: must contain one of the following
+- compatible: should be "renesas,mmcif-<soctype>", "renesas,sh-mmcif" as a
+  fallback. Examples with <soctype> are:
 	- "renesas,mmcif-r8a7740" for the MMCIF found in r8a7740 SoCs
 	- "renesas,mmcif-r8a7790" for the MMCIF found in r8a7790 SoCs
 	- "renesas,mmcif-r8a7791" for the MMCIF found in r8a7791 SoCs
-	- "renesas,sh-mmcif" for the generic MMCIF
+	- "renesas,mmcif-r8a7794" for the MMCIF found in r8a7794 SoCs
 
 - clocks: reference to the functional clock
 
diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
index c327c2d6f23d..3dc13b68fc3f 100644
--- a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt
@@ -14,6 +14,19 @@ Required Properties:
 							before RK3288
 	- "rockchip,rk3288-dw-mshc": for Rockchip RK3288
 
+Optional Properties:
+* clocks: from common clock binding: if ciu_drive and ciu_sample are
+  specified in clock-names, should contain handles to these clocks.
+
+* clock-names: Apart from the clock-names described in synopsys-dw-mshc.txt
+  two more clocks "ciu-drive" and "ciu-sample" are supported. They are used
+  to control the clock phases, "ciu-sample" is required for tuning high-
+  speed modes.
+
+* rockchip,default-sample-phase: The default phase to set ciu_sample at
+  probing, low speeds or in case where all phases work at tuning time.
+  If not specified 0 deg will be used.
+
 Example:
 
 	rkdwmmc0@12200000 {
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
index 346c6095a615..8636f5ae97e5 100644
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
@@ -75,6 +75,12 @@ Optional properties:
 * vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
   specified we'll defer probe until we can find this regulator.
 
+* dmas: List of DMA specifiers with the controller specific format as described
+  in the generic DMA client binding. Refer to dma.txt for details.
+
+* dma-names: request names for generic DMA client binding. Must be "rx-tx".
+  Refer to dma.txt for details.
+
 Aliases:
 
 - All the MSHC controller nodes should be represented in the aliases node using
@@ -95,6 +101,23 @@ board specific portions as listed below.
 		#size-cells = <0>;
 	};
 
+[board specific internal DMA resources]
+
+	dwmmc0@12200000 {
+		clock-frequency = <400000000>;
+		clock-freq-min-max = <400000 200000000>;
+		num-slots = <1>;
+		broken-cd;
+		fifo-depth = <0x80>;
+		card-detect-delay = <200>;
+		vmmc-supply = <&buck8>;
+		bus-width = <8>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+	};
+
+[board specific generic DMA request binding]
+
 	dwmmc0@12200000 {
 		clock-frequency = <400000000>;
 		clock-freq-min-max = <400000 200000000>;
@@ -106,4 +129,6 @@ board specific portions as listed below.
 		bus-width = <8>;
 		cap-mmc-highspeed;
 		cap-sd-highspeed;
+		dmas = <&pdma 12>;
+		dma-names = "rx-tx";
 	};
diff --git a/Documentation/mmc/mmc-dev-attrs.txt b/Documentation/mmc/mmc-dev-attrs.txt
index 189bab09255a..caa555706f89 100644
--- a/Documentation/mmc/mmc-dev-attrs.txt
+++ b/Documentation/mmc/mmc-dev-attrs.txt
@@ -72,13 +72,3 @@ Note on raw_rpmb_size_mult:
 	"raw_rpmb_size_mult" is a mutliple of 128kB block.
 	RPMB size in byte is calculated by using the following equation:
 	RPMB partition size = 128kB x raw_rpmb_size_mult
-
-SD/MMC/SDIO Clock Gating Attribute
-==================================
-
-Read and write access is provided to following attribute.
-This attribute appears only if CONFIG_MMC_CLKGATE is enabled.
-
-	clkgate_delay	Tune the clock gating delay with desired value in milliseconds.
-
-echo <desired delay> > /sys/class/mmc_host/mmcX/clkgate_delay
diff --git a/arch/arc/configs/axs101_defconfig b/arch/arc/configs/axs101_defconfig
index 562dac6a7f78..c92c0ef1e9d2 100644
--- a/arch/arc/configs/axs101_defconfig
+++ b/arch/arc/configs/axs101_defconfig
@@ -89,7 +89,6 @@ CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS=y
diff --git a/arch/arc/configs/axs103_defconfig b/arch/arc/configs/axs103_defconfig
index 83a6d8d5cc58..cfac24e0e7b6 100644
--- a/arch/arc/configs/axs103_defconfig
+++ b/arch/arc/configs/axs103_defconfig
@@ -95,7 +95,6 @@ CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS=y
diff --git a/arch/arc/configs/axs103_smp_defconfig b/arch/arc/configs/axs103_smp_defconfig
index f1e1c84e0dda..9922a118a15a 100644
--- a/arch/arc/configs/axs103_smp_defconfig
+++ b/arch/arc/configs/axs103_smp_defconfig
@@ -96,7 +96,6 @@ CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS=y
diff --git a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi b/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi
index b5334ecff13c..fec076eb7aef 100644
--- a/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi
+++ b/arch/arm/boot/dts/rk3288-veyron-sdmmc.dtsi
@@ -90,7 +90,7 @@
 	regulators {
 		vccio_sd: LDO_REG4 {
 			regulator-name = "vccio_sd";
-			regulator-min-microvolt = <3300000>;
+			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <3300000>;
 			regulator-state-mem {
 				regulator-off-in-suspend;
@@ -116,7 +116,12 @@
 	cap-sd-highspeed;
 	card-detect-delay = <200>;
 	cd-gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
+	rockchip,default-sample-phase = <90>;
 	num-slots = <1>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
 	vmmc-supply = <&vcc33_sd>;
 	vqmmc-supply = <&vccio_sd>;
 };
diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rk3288-veyron.dtsi
index 275c78ccc0f3..860cea0a7613 100644
--- a/arch/arm/boot/dts/rk3288-veyron.dtsi
+++ b/arch/arm/boot/dts/rk3288-veyron.dtsi
@@ -149,7 +149,9 @@
 	broken-cd;
 	bus-width = <8>;
 	cap-mmc-highspeed;
+	rockchip,default-sample-phase = <158>;
 	disable-wp;
+	mmc-hs200-1_8v;
 	mmc-pwrseq = <&emmc_pwrseq>;
 	non-removable;
 	num-slots = <1>;
@@ -355,6 +357,10 @@
 	num-slots = <1>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdio0_clk &sdio0_cmd &sdio0_bus4>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
 	vmmc-supply = <&vcc33_sys>;
 	vqmmc-supply = <&vcc18_wl>;
 };
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 906e938fb6bf..4e7c6b7392af 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -222,8 +222,9 @@
 	sdmmc: dwmmc@ff0c0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		clock-freq-min-max = <400000 150000000>;
-		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>;
-		clock-names = "biu", "ciu";
+		clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
+			 <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0xff0c0000 0x4000>;
@@ -233,8 +234,9 @@
 	sdio0: dwmmc@ff0d0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		clock-freq-min-max = <400000 150000000>;
-		clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>;
-		clock-names = "biu", "ciu";
+		clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>,
+			 <&cru SCLK_SDIO0_DRV>, <&cru SCLK_SDIO0_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0xff0d0000 0x4000>;
@@ -244,8 +246,9 @@
 	sdio1: dwmmc@ff0e0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		clock-freq-min-max = <400000 150000000>;
-		clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>;
-		clock-names = "biu", "ciu";
+		clocks = <&cru HCLK_SDIO1>, <&cru SCLK_SDIO1>,
+			 <&cru SCLK_SDIO1_DRV>, <&cru SCLK_SDIO1_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0xff0e0000 0x4000>;
@@ -255,8 +258,9 @@
 	emmc: dwmmc@ff0f0000 {
 		compatible = "rockchip,rk3288-dw-mshc";
 		clock-freq-min-max = <400000 150000000>;
-		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>;
-		clock-names = "biu", "ciu";
+		clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>,
+			 <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
 		fifo-depth = <0x100>;
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0xff0f0000 0x4000>;
diff --git a/arch/arm/configs/exynos_defconfig b/arch/arm/configs/exynos_defconfig
index 1ff2bfa2e183..13ba48c4b03b 100644
--- a/arch/arm/configs/exynos_defconfig
+++ b/arch/arm/configs/exynos_defconfig
@@ -166,7 +166,6 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_S3C=y
 CONFIG_MMC_SDHCI_S3C_DMA=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 CONFIG_MMC_DW_EXYNOS=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_MAX77686=y
diff --git a/arch/arm/configs/hisi_defconfig b/arch/arm/configs/hisi_defconfig
index 5997dbc69822..b2e340b272ee 100644
--- a/arch/arm/configs/hisi_defconfig
+++ b/arch/arm/configs/hisi_defconfig
@@ -69,7 +69,6 @@ CONFIG_NOP_USB_XCEIV=y
 CONFIG_MMC=y
 CONFIG_RTC_CLASS=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 CONFIG_MMC_DW_PLTFM=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_DMADEVICES=y
diff --git a/arch/arm/configs/lpc18xx_defconfig b/arch/arm/configs/lpc18xx_defconfig
index 1c47f86c3970..b7e8cdab51f9 100644
--- a/arch/arm/configs/lpc18xx_defconfig
+++ b/arch/arm/configs/lpc18xx_defconfig
@@ -119,7 +119,6 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 CONFIG_MMC=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_PCA9532=y
diff --git a/arch/mips/configs/pistachio_defconfig b/arch/mips/configs/pistachio_defconfig
index 642b50946943..8b7429127a1d 100644
--- a/arch/mips/configs/pistachio_defconfig
+++ b/arch/mips/configs/pistachio_defconfig
@@ -257,7 +257,6 @@ CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=16
 CONFIG_MMC_TEST=m
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_IDMAC=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_RTC_CLASS=y
diff --git a/drivers/clk/rockchip/clk-mmc-phase.c b/drivers/clk/rockchip/clk-mmc-phase.c
index 9b613426e968..bc24e5a002e7 100644
--- a/drivers/clk/rockchip/clk-mmc-phase.c
+++ b/drivers/clk/rockchip/clk-mmc-phase.c
@@ -45,8 +45,8 @@ static unsigned long rockchip_mmc_recalc(struct clk_hw *hw,
 #define PSECS_PER_SEC 1000000000000LL
 
 /*
- * Each fine delay is between 40ps-80ps. Assume each fine delay is 60ps to
- * simplify calculations. So 45degs could be anywhere between 33deg and 66deg.
+ * Each fine delay is between 44ps-77ps. Assume each fine delay is 60ps to
+ * simplify calculations. So 45degs could be anywhere between 33deg and 57.8deg.
  */
 #define ROCKCHIP_MMC_DELAY_ELEMENT_PSEC 60
 
@@ -69,7 +69,7 @@ static int rockchip_mmc_get_phase(struct clk_hw *hw)
 
 		delay_num = (raw_value & ROCKCHIP_MMC_DELAYNUM_MASK);
 		delay_num >>= ROCKCHIP_MMC_DELAYNUM_OFFSET;
-		degrees += delay_num * factor / 10000;
+		degrees += DIV_ROUND_CLOSEST(delay_num * factor, 10000);
 	}
 
 	return degrees % 360;
@@ -82,25 +82,41 @@ static int rockchip_mmc_set_phase(struct clk_hw *hw, int degrees)
 	u8 nineties, remainder;
 	u8 delay_num;
 	u32 raw_value;
-	u64 delay;
-
-	/* allow 22 to be 22.5 */
-	degr