Merge tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
 "Not much going on in the core for SPI this time but a reasonable
  amount of change in the drivers:

   - Removal of dmal_request_slave_channel() from Peter Ujfalusi.

   - More conversions of drivers to GPIO descriptors from Linus Walleij.

   - A big rework of the sh-msiof driver from Geert Uytterhoeven moving
     it over to the generic native chipselect support.

   - DMA support for the uniphier driver from Kunihiko Hayashi.

   - New driver support for HiSilcon v3xx SPI NOR controllers from John
     Garry"

* tag 'spi-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (52 commits)
  dt-binding: spi: add NPCM PSPI reset binding
  spi: pxa2xx: Avoid touching SSCR0_SSE on MMP2
  spi: spi-fsl-qspi: Ensure width is respected in spi-mem operations
  spi: npcm-pspi: modify reset support
  spi: npcm-pspi: improve spi transfer performance
  spi: spi-ti-qspi: fix warning
  spi: npcm-pspi: fix 16 bit send and receive support
  spi: pxa2xx: Add support for Intel Comet Lake PCH-V
  spi: fsl: simplify error path in of_fsl_spi_probe()
  spi: fsl-lpspi: fix only one cs-gpio working
  spi: spi-ti-qspi: optimize byte-transfers
  spi: spi-ti-qspi: support large flash devices
  spi: spi-qcom-qspi: Use device managed memory for clk_bulk_data
  MAINTAINERS: Add a maintainer for the HiSilicon v3xx SFC driver
  spi: Add HiSilicon v3xx SPI NOR flash controller driver
  dt-bindings: spi_atmel: add microchip,sam9x60-spi
  spi: bcm2835: Raise maximum number of slaves to 4
  spi: sh-msiof: Do not redefine STR while compile testing
  spi: rspi: Add support for GPIO chip selects
  spi: rspi: Add support for multiple native chip selects
  ...

37 files changed, 1208 insertions, 628 deletions

diff --git a/Documentation/devicetree/bindings/spi/nuvoton,npcm-pspi.txt b/Documentation/devicetree/bindings/spi/nuvoton,npcm-pspi.txt
index 1fd9a4406a1d..b98203ca656d 100644
--- a/Documentation/devicetree/bindings/spi/nuvoton,npcm-pspi.txt
+++ b/Documentation/devicetree/bindings/spi/nuvoton,npcm-pspi.txt
@@ -12,6 +12,7 @@ Required properties:
  - clock-names: Should be "clk_apb5".
  - pinctrl-names : a pinctrl state named "default" must be defined.
  - pinctrl-0 : phandle referencing pin configuration of the device.
+ - resets : phandle to the reset control for this device.
  - cs-gpios: Specifies the gpio pins to be used for chipselects.
             See: Documentation/devicetree/bindings/spi/spi-bus.txt
 
@@ -19,16 +20,6 @@ Optional properties:
 - clock-frequency : Input clock frequency to the PSPI block in Hz.
 		    Default is 25000000 Hz.
 
-Aliases:
-- All the SPI controller nodes should be represented in the aliases node using
-  the following format 'spi{n}' withe the correct numbered in "aliases" node.
-
-Example:
-
-aliases {
-	spi0 = &spi0;
-};
-
 spi0: spi@f0200000 {
 	compatible = "nuvoton,npcm750-pspi";
 	reg = <0xf0200000 0x1000>;
@@ -39,5 +30,6 @@ spi0: spi@f0200000 {
 	interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 	clocks = <&clk NPCM7XX_CLK_APB5>;
 	clock-names = "clk_apb5";
+	resets = <&rstc NPCM7XX_RESET_IPSRST2 NPCM7XX_RESET_PSPI1>
 	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 };
diff --git a/Documentation/devicetree/bindings/spi/spi-stm32.txt b/Documentation/devicetree/bindings/spi/spi-stm32.txt
deleted file mode 100644
index d82755c63eaf..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-stm32.txt
+++ /dev/null
@@ -1,62 +0,0 @@
-STMicroelectronics STM32 SPI Controller
-
-The STM32 SPI controller is used to communicate with external devices using
-the Serial Peripheral Interface. It supports full-duplex, half-duplex and
-simplex synchronous serial communication with external devices. It supports
-from 4 to 32-bit data size. Although it can be configured as master or slave,
-only master is supported by the driver.
-
-Required properties:
-- compatible: Should be one of:
-  "st,stm32h7-spi"
-  "st,stm32f4-spi"
-- reg: Offset and length of the device's register set.
-- interrupts: Must contain the interrupt id.
-- clocks: Must contain an entry for spiclk (which feeds the internal clock
-	  generator).
-- #address-cells:  Number of cells required to define a chip select address.
-- #size-cells: Should be zero.
-
-Optional properties:
-- resets: Must contain the phandle to the reset controller.
-- A pinctrl state named "default" may be defined to set pins in mode of
-  operation for SPI transfer.
-- dmas: DMA specifiers for tx and rx dma. DMA fifo mode must be used. See the
-  STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt.
-- dma-names: DMA request names should include "tx" and "rx" if present.
-- cs-gpios: list of GPIO chip selects. See the SPI bus bindings,
-  Documentation/devicetree/bindings/spi/spi-bus.txt
-
-
-Child nodes represent devices on the SPI bus
-  See ../spi/spi-bus.txt
-
-Optional properties:
-- st,spi-midi-ns: Only for STM32H7, (Master Inter-Data Idleness) minimum time
-		  delay in nanoseconds inserted between two consecutive data
-		  frames.
-
-
-Example:
-	spi2: spi@40003800 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "st,stm32h7-spi";
-		reg = <0x40003800 0x400>;
-		interrupts = <36>;
-		clocks = <&rcc SPI2_CK>;
-		resets = <&rcc 1166>;
-		dmas = <&dmamux1 0 39 0x400 0x01>,
-		       <&dmamux1 1 40 0x400 0x01>;
-		dma-names = "rx", "tx";
-		pinctrl-0 = <&spi2_pins_b>;
-		pinctrl-names = "default";
-		cs-gpios = <&gpioa 11 0>;
-
-		aardvark@0 {
-			compatible = "totalphase,aardvark";
-			reg = <0>;
-			spi-max-frequency = <4000000>;
-			st,spi-midi-ns = <4000>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt
index f99c733d75c1..5bb4a8f1df7a 100644
--- a/Documentation/devicetree/bindings/spi/spi_atmel.txt
+++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt
@@ -1,7 +1,7 @@
 Atmel SPI device
 
 Required properties:
-- compatible : should be "atmel,at91rm9200-spi".
+- compatible : should be "atmel,at91rm9200-spi" or "microchip,sam9x60-spi".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain spi interrupt
 - cs-gpios: chipselects (optional for SPI controller version >= 2 with the
diff --git a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
new file mode 100644
index 000000000000..f0d979664f07
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/st,stm32-spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics STM32 SPI Controller bindings
+
+description: |
+  The STM32 SPI controller is used to communicate with external devices using
+  the Serial Peripheral Interface. It supports full-duplex, half-duplex and
+  simplex synchronous serial communication with external devices. It supports
+  from 4 to 32-bit data size.
+
+maintainers:
+  - Erwan Leray <erwan.leray@st.com>
+  - Fabrice Gasnier <fabrice.gasnier@st.com>
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: st,stm32f4-spi
+
+    then:
+      properties:
+        st,spi-midi-ns: false
+
+properties:
+  compatible:
+    enum:
+      - st,stm32f4-spi
+      - st,stm32h7-spi
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  dmas:
+    description: |
+      DMA specifiers for tx and rx dma. DMA fifo mode must be used. See
+      the STM32 DMA bindings Documentation/devicetree/bindings/dma/stm32-dma.txt.
+    items:
+      - description: rx DMA channel
+      - description: tx DMA channel
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+patternProperties:
+  "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
+    type: object
+    # SPI slave nodes must be children of the SPI master node and can
+    # contain the following properties.
+    properties:
+      st,spi-midi-ns:
+        description: |
+          Only for STM32H7, (Master Inter-Data Idleness) minimum time
+          delay in nanoseconds inserted between two consecutive data frames.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    #include <dt-bindings/reset/stm32mp1-resets.h>
+    spi@4000b000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      compatible = "st,stm32h7-spi";
+      reg = <0x4000b000 0x400>;
+      interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+      clocks = <&rcc SPI2_K>;
+      resets = <&rcc SPI2_R>;
+      dmas = <&dmamux1 0 39 0x400 0x05>,
+             <&dmamux1 1 40 0x400 0x05>;
+      dma-names = "rx", "tx";
+      cs-gpios = <&gpioa 11 0>;
+
+      aardvark@0 {
+        compatible = "totalphase,aardvark";
+        reg = <0>;
+        spi-max-frequency = <4000000>;
+        st,spi-midi-ns = <4000>;
+      };
+    };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index a7ce7bfcb4e9..1575d416f2db 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7509,6 +7509,12 @@ S:	Supported
 F:	drivers/scsi/hisi_sas/
 F:	Documentation/devicetree/bindings/scsi/hisilicon-sas.txt
 
+HISILICON V3XX SPI NOR FLASH Controller Driver
+M:	John Garry <john.garry@huawei.com>
+W:	http://www.hisilicon.com
+S:	Maintained
+F:	drivers/spi/spi-hisi-sfc-v3xx.c
+
 HISILICON QM AND ZIP Controller DRIVER
 M:	Zhou Wang <wangzhou1@hisilicon.com>
 L:	linux-crypto@vger.kernel.org
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 870f7797b56b..d6ed0c355954 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -281,6 +281,15 @@ config SPI_FSL_QUADSPI
 	  This controller does not support generic SPI messages. It only
 	  supports the high-level SPI memory interface.
 
+config SPI_HISI_SFC_V3XX
+	tristate "HiSilicon SPI-NOR Flash Controller for Hi16XX chipsets"
+	depends on (ARM64 && ACPI) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select CONFIG_MTD_SPI_NOR
+	help
+	  This enables support for HiSilicon v3xx SPI-NOR flash controller
+	  found in hi16xx chipsets.
+
 config SPI_NXP_FLEXSPI
 	tristate "NXP Flex SPI controller"
 	depends on ARCH_LAYERSCAPE || HAS_IOMEM
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index bb49c9e6d0a0..9b65ec5afc5e 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -48,6 +48,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
 obj-$(CONFIG_SPI_FSL_QUADSPI)		+= spi-fsl-qspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
+obj-$(CONFIG_SPI_HISI_SFC_V3XX)		+= spi-hisi-sfc-v3xx.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
 obj-$(CONFIG_SPI_IMX)			+= spi-imx.o
 obj-$(CONFIG_SPI_LANTIQ_SSC)		+= spi-lantiq-ssc.o
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 56f0ca361deb..013458cabe3c 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -514,26 +514,19 @@ static int atmel_spi_configure_dma(struct spi_master *master,
 	master->dma_tx = dma_request_chan(dev, "tx");
 	if (IS_ERR(master->dma_tx)) {
 		err = PTR_ERR(master->dma_tx);
-		if (err == -EPROBE_DEFER) {
-			dev_warn(dev, "no DMA channel available at the moment\n");
-			goto error_clear;
-		}
-		dev_err(dev,
-			"DMA TX channel not available, SPI unable to use DMA\n");
-		err = -EBUSY;
+		if (err != -EPROBE_DEFER)
+			dev_err(dev, "No TX DMA channel, DMA is disabled\n");
 		goto error_clear;
 	}
 
-	/*
-	 * No reason to check EPROBE_DEFER here since we have already requested
-	 * tx channel. If it fails here, it's for another reason.
-	 */
-	master->dma_rx = dma_request_slave_channel(dev, "rx");
-
-	if (!master->dma_rx) {
-		dev_err(dev,
-			"DMA RX channel not available, SPI unable to use DMA\n");
-		err = -EBUSY;
+	master->dma_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(master->dma_rx)) {
+		err = PTR_ERR(master->dma_rx);
+		/*
+		 * No reason to check EPROBE_DEFER here since we have already
+		 * requested tx channel.
+		 */
+		dev_err(dev, "No RX DMA channel, DMA is disabled\n");
 		goto error;
 	}
 
@@ -548,7 +541,7 @@ static int atmel_spi_configure_dma(struct spi_master *master,
 
 	return 0;
 error:
-	if (master->dma_rx)
+	if (!IS_ERR(master->dma_rx))
 		dma_release_channel(master->dma_rx);
 	if (!IS_ERR(master->dma_tx))
 		dma_release_channel(master->dma_tx);
diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c
index 85bad70f59e3..23d295f36c80 100644
--- a/drivers/spi/spi-bcm-qspi.c
+++ b/drivers/spi/spi-bcm-qspi.c
@@ -1293,7 +1293,7 @@ int bcm_qspi_probe(struct platform_device *pdev,
 		name = qspi_irq_tab[val].irq_name;
 		if (qspi_irq_tab[val].irq_source == SINGLE_L2) {
 			/* get the l2 interrupts */
-			irq = platform_get_irq_byname(pdev, name);
+			irq = platform_get_irq_byname_optional(pdev, name);
 		} else if (!num_ints && soc_intc) {
 			/* all mspi, bspi intrs muxed to one L1 intr */
 			irq = platform_get_irq(pdev, 0);
diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
index fb61a620effc..11c235879bb7 100644
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -68,7 +68,7 @@
 #define BCM2835_SPI_FIFO_SIZE		64
 #define BCM2835_SPI_FIFO_SIZE_3_4	48
 #define BCM2835_SPI_DMA_MIN_LENGTH	96
-#define BCM2835_SPI_NUM_CS		3   /* raise as necessary */
+#define BCM2835_SPI_NUM_CS		4   /* raise as necessary */
 #define BCM2835_SPI_MODE_BITS	(SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
 				| SPI_NO_CS | SPI_3WIRE)
 
@@ -888,8 +888,8 @@ static void bcm2835_dma_release(struct spi_controller *ctlr,
 	}
 }
 
-static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
-			     struct bcm2835_spi *bs)
+static int bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
+			    struct bcm2835_spi *bs)
 {
 	struct dma_slave_config slave_config;
 	const __be32 *addr;
@@ -900,19 +900,24 @@ static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 	addr = of_get_address(ctlr->dev.of_node, 0, NULL, NULL);
 	if (!addr) {
 		dev_err(dev, "could not get DMA-register address - not using dma mode\n");
-		goto err;
+		/* Fall back to interrupt mode */
+		return 0;
 	}
 	dma_reg_base = be32_to_cpup(addr);
 
 	/* get tx/rx dma */
-	ctlr->dma_tx = dma_request_slave_channel(dev, "tx");
-	if (!ctlr->dma_tx) {
+	ctlr->dma_tx = dma_request_chan(dev, "tx");
+	if (IS_ERR(ctlr->dma_tx)) {
 		dev_err(dev, "no tx-dma configuration found - not using dma mode\n");
+		ret = PTR_ERR(ctlr->dma_tx);
+		ctlr->dma_tx = NULL;
 		goto err;
 	}
-	ctlr->dma_rx = dma_request_slave_channel(dev, "rx");
-	if (!ctlr->dma_rx) {
+	ctlr->dma_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(ctlr->dma_rx)) {
 		dev_err(dev, "no rx-dma configuration found - not using dma mode\n");
+		ret = PTR_ERR(ctlr->dma_rx);
+		ctlr->dma_rx = NULL;
 		goto err_release;
 	}
 
@@ -997,7 +1002,7 @@ static void bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 	/* all went well, so set can_dma */
 	ctlr->can_dma = bcm2835_spi_can_dma;
 
-	return;
+	return 0;
 
 err_config:
 	dev_err(dev, "issue configuring dma: %d - not using DMA mode\n",
@@ -1005,7 +1010,14 @@ err_config:
 err_release:
 	bcm2835_dma_release(ctlr, bs);
 err:
-	return;
+	/*
+	 * Only report error for deferred probing, otherwise fall back to
+	 * interrupt mode
+	 */
+	if (ret != -EPROBE_DEFER)
+		ret = 0;
+
+	return ret;
 }
 
 static int bcm2835_spi_transfer_one_poll(struct spi_controller *ctlr,
@@ -1305,7 +1317,10 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 	bs->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(bs->clk)) {
 		err = PTR_ERR(bs->clk);
-		dev_err(&pdev->dev, "could not get clk: %d\n", err);
+		if (err == -EPROBE_DEFER)
+			dev_dbg(&pdev->dev, "could not get clk: %d\n", err);
+		else
+			dev_err(&pdev->dev, "could not get clk: %d\n", err);
 		goto out_controller_put;
 	}
 
@@ -1317,7 +1332,9 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 
 	clk_prepare_enable(bs->clk);
 
-	bcm2835_dma_init(ctlr, &pdev->dev, bs);
+	err = bcm2835_dma_init(ctlr, &pdev->dev, bs);
+	if (err)
+		goto out_clk_disable;
 
 	/* initialise the hardware with the default polarities */
 	bcm2835_wr(bs, BCM2835_SPI_CS,
@@ -1327,20 +1344,22 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 			       dev_name(&pdev->dev), ctlr);
 	if (err) {
 		dev_err(&pdev->dev, "could not request IRQ: %d\n", err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	err = devm_spi_register_controller(&pdev->dev, ctlr);
 	if (err) {
 		dev_err(&pdev->dev, "could not register SPI controller: %d\n",
 			err);
-		goto out_clk_disable;
+		goto out_dma_release;
 	}
 
 	bcm2835_debugfs_create(bs, dev_name(&pdev->dev));
 
 	return 0;
 
+out_dma_release:
+	bcm2835_dma_release(ctlr, bs);
 out_clk_disable:
 	clk_disable_unprepare(bs->clk);
 out_controller_put:
diff --git a/drivers/spi/spi-bitbang.c b/drivers/spi/spi-bitbang.c
index d84e22dd6f9f..68491a8bf7b5 100644
--- a/drivers/spi/spi-bitbang.c
+++ b/drivers/spi/spi-bitbang.c
@@ -329,8 +329,20 @@ static void spi_bitbang_set_cs(struct spi_device *spi, bool enable)
 int spi_bitbang_init(struct spi_bitbang *bitbang)
 {
 	struct spi_master *master = bitbang->master;
+	bool custom_cs;
 
-	if (!master || !bitbang->chipselect)
+	if (!master)
+		return -EINVAL;
+	/*
+	 * We only need the chipselect callback if we are actually using it.
+	 * If we just use GPIO descriptors, it is surplus. If the
+	 * SPI_MASTER_GPIO_SS flag is set, we always need to call the
+	 * driver-specific chipselect routine.
+	 */
+	custom_cs = (!master->use_gpio_descriptors ||
+		     (master->flags & SPI_MASTER_GPIO_SS));
+
+	if (custom_cs && !bitbang->chipselect)
 		return -EINVAL;
 
 	mutex_init(&bitbang->lock);
@@ -344,7 +356,12 @@ int spi_bitbang_init(struct spi_bitbang *bitbang)
 	master->prepare_transfer_hardware = spi_bitbang_prepare_hardware;
 	master->unprepare_transfer_hardware = spi_bitbang_unprepare_hardware;
 	master->transfer_one = spi_bitbang_transfer_one;
-	master->set_cs = spi_bitbang_set_cs;
+	/*
+	 * When using GPIO descriptors, the ->set_cs() callback doesn't even
+	 * get called unless SPI_MASTER_GPIO_SS is set.
+	 */
+	if (custom_cs)
+		master->set_cs = spi_bitbang_set_cs;
 
 	if (!bitbang->txrx_bufs) {
 		bitbang->use_dma = 0;
diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
index 5a25da377119..31e3f866d11a 100644
--- a/drivers/spi/spi-dw.c
+++ b/drivers/spi/spi-dw.c
@@ -297,6 +297,9 @@ static int dw_spi_transfer_one(struct spi_controller *master,
 	dws->len = transfer->len;
 	spin_unlock_irqrestore(&dws->buf_lock, flags);
 
+	/* Ensure dw->rx and dw->rx_end are visible */
+	smp_mb();
+
 	spi_enable_chip(dws, 0);
 
 	/* Handle per transfer options for bpw and speed */
@@ -469,7 +472,8 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
 	struct spi_controller *master;
 	int ret;
 
-	BUG_ON(dws == NULL);
+	if (!dws)
+		return -EINVAL;
 
 	master = spi_alloc_master(dev, 0);
 	if (!master)
diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c
index 8428b69c858b..6ec2dcb8c57a 100644
--- a/drivers/spi/spi-fsl-dspi.c
+++ b/drivers/spi/spi-fsl-dspi.c
@@ -396,17 +396,17 @@ static int dspi_request_dma(struct fsl_dspi *dspi, phys_addr_t phy_addr)
 	if (!dma)
 		return -ENOMEM;
 
-	dma->chan_rx = dma_request_slave_channel(dev, "rx");
-	if (!dma->chan_rx) {
+	dma->chan_rx = dma_request_chan(dev, "rx");
+	if (IS_ERR(dma->chan_rx)) {
 		dev_err(dev, "rx dma channel not available\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(dma->chan_rx);
 		return ret;
 	}
 
-	dma->chan_tx = dma_request_slave_channel(dev, "tx");
-	if (!dma->chan_tx) {
+	dma->chan_tx = dma_request_chan(dev, "tx");
+	if (IS_ERR(dma->chan_tx)) {
 		dev_err(dev, "tx dma channel not available\n");
-		ret = -ENODEV;
+		ret = PTR_ERR(dma->chan_tx);
 		goto err_tx_channel;
 	}
 
diff --git a/drivers/spi/spi-fsl-lpspi.c b/drivers/spi/spi-fsl-lpspi.c
index 2cc0ddb4a988..d0b8cc741a24 100644
--- a/drivers/spi/spi-fsl-lpspi.c
+++ b/drivers/spi/spi-fsl-lpspi.c
@@ -469,9 +469,9 @@ static int fsl_lpspi_setup_transfer(struct spi_controller *controller,
 		fsl_lpspi->watermark = fsl_lpspi->txfifosize;
 
 	if (fsl_lpspi_can_dma(controller, spi, t))
-		fsl_lpspi->usedma = 1;
+		fsl_lpspi->usedma = true;
 	else
-		fsl_lpspi->usedma = 0;
+		fsl_lpspi->usedma = false;
 
 	return fsl_lpspi_config(fsl_lpspi);
 }
@@ -862,6 +862,22 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 	fsl_lpspi->dev = &pdev->dev;
 	fsl_lpspi->is_slave = is_slave;
 
+	controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
+	controller->transfer_one = fsl_lpspi_transfer_one;
+	controller->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
+	controller->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
+	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+	controller->dev.of_node = pdev->dev.of_node;
+	controller->bus_num = pdev->id;
+	controller->slave_abort = fsl_lpspi_slave_abort;
+
+	ret = devm_spi_register_controller(&pdev->dev, controller);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "spi_register_controller error.\n");
+		goto out_controller_put;
+	}
+
 	if (!fsl_lpspi->is_slave) {
 		for (i = 0; i < controller->num_chipselect; i++) {
 			int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
@@ -885,16 +901,6 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 		controller->prepare_message = fsl_lpspi_prepare_message;
 	}
 
-	controller->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32);
-	controller->transfer_one = fsl_lpspi_transfer_one;
-	controller->prepare_transfer_hardware = lpspi_prepare_xfer_hardware;
-	controller->unprepare_transfer_hardware = lpspi_unprepare_xfer_hardware;
-	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
-	controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
-	controller->dev.of_node = pdev->dev.of_node;
-	controller->bus_num = pdev->id;
-	controller->slave_abort = fsl_lpspi_slave_abort;
-
 	init_completion(&fsl_lpspi->xfer_done);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -952,12 +958,6 @@ static int fsl_lpspi_probe(struct platform_device *pdev)
 	if (ret < 0)
 		dev_err(&pdev->dev, "dma setup error %d, use pio\n", ret);
 
-	ret = devm_spi_register_controller(&pdev->dev, controller);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "spi_register_controller error.\n");
-		goto out_controller_put;
-	}
-
 	return 0;
 
 out_controller_put:
diff --git a/drivers/spi/spi-fsl-qspi.c b/drivers/spi/spi-fsl-qspi.c
index 79b1558b74b8..e8a499cd1f13 100644
--- a/drivers/spi/spi-fsl-qspi.c
+++ b/drivers/spi/spi-fsl-qspi.c
@@ -410,7 +410,7 @@ static bool fsl_qspi_supports_op(struct spi_mem *mem,
 	    op->data.nbytes > q->devtype_data->txfifo)
 		return false;
 
-	return true;
+	return spi_mem_default_supports_op(mem, op);
 }
 
 static void fsl_qspi_prepare_lut(struct fsl_qspi *q,
diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c
index fb4159ad6bf6..3b81772fea0d 100644
--- a/drivers/spi/spi-fsl-spi.c
+++ b/drivers/spi/spi-fsl-spi.c
@@ -706,8 +706,8 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 	struct device_node *np = ofdev->dev.of_node;
 	struct spi_master *master;
 	struct resource mem;
-	int irq = 0, type;
-	int ret = -ENOMEM;
+	int irq, type;
+	int ret;
 
 	ret = of_mpc8xxx_spi_probe(ofdev);
 	if (ret)
@@ -722,10 +722,8 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 
 		if (spisel_boot) {
 			pinfo->immr_spi_cs = ioremap(get_immrbase() + IMMR_SPI_CS_OFFSET, 4);
-			if (!pinfo->immr_spi_cs) {
-				ret = -ENOMEM;
-				goto err;
-			}
+			if (!pinfo->immr_spi_cs)
+				return -ENOMEM;
 		}
 #endif
 		/*
@@ -744,24 +742,15 @@ static int of_fsl_spi_probe(struct platform_device *ofdev)
 
 	ret = of_address_to_resource(np, 0, &mem);
 	if (ret)
-		goto err;
+		return ret;
 
 	irq = platform_get_irq(ofdev, 0);
-	if (irq < 0) {
-		ret = irq;
-		goto err;
-	}
+	if (irq < 0)
+		return irq;