Merge tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "Clean-up for omaps for v4.2 merge window" from Tony Lindgren:

Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.

The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.

This leaves us with only the following board-*.c files:

BOARD                   REASON NEEDED
board-ldp.c             Still used in RMKs boot test system
board-omap3logic.c      Getting a .dts file for v4.2
board-omap3pandora.c    Got a .dts file for v4.1
board-rx51-*.c          Needs /proc/atags support for user space

I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.

Also, few patches to clean-up the usage of Linux generic
macros:

- Use define for console loglevel

- Use const for struct irq_domain_ops

- Use PTR_ERR_OR_ZERO instead of PTR_RET

* tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
  ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
  ARM: OMAP2+: Constify irq_domain_ops
  ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
  ARM: OMAP2+: Remove legacy booting support for Beagleboards
  ARM: OMAP2+: Remove legacy booting support for Overo
  ARM: OMAP2+: Remove legacy booting support for cm-t35

10 files changed, 6 insertions, 1966 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 6468f15f060c..ecc04ff13e95 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -171,12 +171,6 @@ config MACH_OMAP2_TUSB6010
 	depends on ARCH_OMAP2 && SOC_OMAP2420
 	default y if MACH_NOKIA_N8X0
 
-config MACH_OMAP3_BEAGLE
-	bool "OMAP3 BEAGLE board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP_LDP
 	bool "OMAP3 LDP board"
 	depends on ARCH_OMAP3
@@ -203,12 +197,6 @@ config MACH_OMAP3_TORPEDO
 	 for full description please see the products webpage at
 	 http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
 
-config MACH_OVERO
-	bool "Gumstix Overo board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3
@@ -240,16 +228,6 @@ config MACH_NOKIA_RX51
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_CM_T35
-	bool "CompuLab CM-T35/CM-T3730 modules"
-	depends on ARCH_OMAP3
-	default y
-	select MACH_CM_T3730
-	select OMAP_PACKAGE_CUS
-
-config MACH_CM_T3730
-       bool
-
 config OMAP3_SDRC_AC_TIMING
 	bool "Enable SDRC AC timing register changes"
 	depends on ARCH_OMAP3
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index ec002bd4af77..f1a68c63dc99 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -242,17 +242,14 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
-obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
-obj-$(CONFIG_MACH_OVERO)		+= board-overo.o
 obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
-obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
 
 # Platform specific device init code
 
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
deleted file mode 100644
index b5dfbc1b1fc6..000000000000
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ /dev/null
@@ -1,769 +0,0 @@
-/*
- * CompuLab CM-T35/CM-T3730 modules support
- *
- * Copyright (C) 2009-2011 CompuLab, Ltd.
- * Authors: Mike Rapoport <mike@compulab.co.il>
- *	    Igor Grinberg <grinberg@compulab.co.il>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- */
-
-#include <linux/clk-provider.h>
-#include <linux/clkdev.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/omap-gpmc.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include <linux/platform_data/at24.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/tdo24m.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include "common.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#define CM_T35_GPIO_PENDOWN		57
-#define SB_T35_USB_HUB_RESET_GPIO	167
-
-#define CM_T35_SMSC911X_CS	5
-#define CM_T35_SMSC911X_GPIO	163
-#define SB_T35_SMSC911X_CS	4
-#define SB_T35_SMSC911X_GPIO	65
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
-	.id		= 0,
-	.cs             = CM_T35_SMSC911X_CS,
-	.gpio_irq       = CM_T35_SMSC911X_GPIO,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
-	.id		= 1,
-	.cs             = SB_T35_SMSC911X_CS,
-	.gpio_irq       = SB_T35_SMSC911X_GPIO,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static struct regulator_consumer_supply cm_t35_smsc911x_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static struct regulator_consumer_supply sb_t35_smsc911x_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
-};
-
-static void __init cm_t35_init_ethernet(void)
-{
-	regulator_register_fixed(0, cm_t35_smsc911x_supplies,
-				 ARRAY_SIZE(cm_t35_smsc911x_supplies));
-	regulator_register_fixed(1, sb_t35_smsc911x_supplies,
-				 ARRAY_SIZE(sb_t35_smsc911x_supplies));
-
-	gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
-	gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
-}
-#else
-static inline void __init cm_t35_init_ethernet(void) { return; }
-#endif
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led cm_t35_leds[] = {
-	[0] = {
-		.gpio			= 186,
-		.name			= "cm-t35:green",
-		.default_trigger	= "heartbeat",
-		.active_low		= 0,
-	},
-};
-
-static struct gpio_led_platform_data cm_t35_led_pdata = {
-	.num_leds	= ARRAY_SIZE(cm_t35_leds),
-	.leds		= cm_t35_leds,
-};
-
-static struct platform_device cm_t35_led_device = {
-	.name		= "leds-gpio",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &cm_t35_led_pdata,
-	},
-};
-
-static void __init cm_t35_init_led(void)
-{
-	platform_device_register(&cm_t35_led_device);
-}
-#else
-static inline void cm_t35_init_led(void) {}
-#endif
-
-#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-
-static struct mtd_partition cm_t35_nand_partitions[] = {
-	{
-		.name           = "xloader",
-		.offset         = 0,			/* Offset = 0x00000 */
-		.size           = 4 * NAND_BLOCK_SIZE,
-		.mask_flags     = MTD_WRITEABLE
-	},
-	{
-		.name           = "uboot",
-		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size           = 15 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name           = "uboot environment",
-		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x260000 */
-		.size           = 2 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name           = "linux",
-		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x2A0000 */
-		.size           = 32 * NAND_BLOCK_SIZE,
-	},
-	{
-		.name           = "rootfs",
-		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x6A0000 */
-		.size           = MTDPART_SIZ_FULL,
-	},
-};
-
-static struct omap_nand_platform_data cm_t35_nand_data = {
-	.parts			= cm_t35_nand_partitions,
-	.nr_parts		= ARRAY_SIZE(cm_t35_nand_partitions),
-	.cs			= 0,
-};
-
-static void __init cm_t35_init_nand(void)
-{
-	if (gpmc_nand_init(&cm_t35_nand_data, NULL) < 0)
-		pr_err("CM-T35: Unable to register NAND device\n");
-}
-#else
-static inline void cm_t35_init_nand(void) {}
-#endif
-
-#define CM_T35_LCD_EN_GPIO 157
-#define CM_T35_LCD_BL_GPIO 58
-#define CM_T35_DVI_EN_GPIO 54
-
-static const struct display_timing cm_t35_lcd_videomode = {
-	.pixelclock	= { 0, 26000000, 0 },
-
-	.hactive = { 0, 480, 0 },
-	.hfront_porch = { 0, 104, 0 },
-	.hback_porch = { 0, 8, 0 },
-	.hsync_len = { 0, 8, 0 },
-
-	.vactive = { 0, 640, 0 },
-	.vfront_porch = { 0, 4, 0 },
-	.vback_porch = { 0, 2, 0 },
-	.vsync_len = { 0, 2, 0 },
-
-	.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
-		DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
-};
-
-static struct panel_dpi_platform_data cm_t35_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 18,
-
-	.display_timing		= &cm_t35_lcd_videomode,
-
-	.enable_gpio		= -1,
-	.backlight_gpio		= CM_T35_LCD_BL_GPIO,
-};
-
-static struct platform_device cm_t35_lcd_device = {
-	.name                   = "panel-dpi",
-	.id                     = 0,
-	.dev.platform_data      = &cm_t35_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data cm_t35_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = -1,
-};
-
-static struct platform_device cm_t35_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &cm_t35_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data cm_t35_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = CM_T35_DVI_EN_GPIO,
-};
-
-static struct platform_device cm_t35_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &cm_t35_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data cm_t35_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device cm_t35_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &cm_t35_tv_pdata,
-};
-
-static struct omap_dss_board_info cm_t35_dss_data = {
-	.default_display_name = "dvi",
-};
-
-static struct omap2_mcspi_device_config tdo24m_mcspi_config = {
-	.turbo_mode	= 0,
-};
-
-static struct tdo24m_platform_data tdo24m_config = {
-	.model = TDO35S,
-};
-
-static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = {
-	{
-		.modalias		= "tdo24m",
-		.bus_num		= 4,
-		.chip_select		= 0,
-		.max_speed_hz		= 1000000,
-		.controller_data	= &tdo24m_mcspi_config,
-		.platform_data		= &tdo24m_config,
-	},
-};
-
-static void __init cm_t35_init_display(void)
-{
-	int err;
-
-	spi_register_board_info(cm_t35_lcd_spi_board_info,
-				ARRAY_SIZE(cm_t35_lcd_spi_board_info));
-
-
-	err = gpio_request_one(CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW,
-			"lcd bl enable");
-	if (err) {
-		pr_err("CM-T35: failed to request LCD EN GPIO\n");
-		return;
-	}
-
-	msleep(50);
-	gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
-
-	err = omap_display_init(&cm_t35_dss_data);
-	if (err) {
-		pr_err("CM-T35: failed to register DSS device\n");
-		gpio_free(CM_T35_LCD_EN_GPIO);
-	}
-
-	platform_device_register(&cm_t35_tfp410_device);
-	platform_device_register(&cm_t35_dvi_connector_device);
-	platform_device_register(&cm_t35_lcd_device);
-	platform_device_register(&cm_t35_tv_connector_device);
-}
-
-static struct regulator_consumer_supply cm_t35_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply cm_t35_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply cm_t35_vio_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi1.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data cm_t35_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(cm_t35_vmmc1_supply),
-	.consumer_supplies	= cm_t35_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data cm_t35_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(cm_t35_vsim_supply),
-	.consumer_supplies	= cm_t35_vsim_supply,
-};
-
-static struct regulator_init_data cm_t35_vio = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(cm_t35_vio_supplies),
-	.consumer_supplies	= cm_t35_vio_supplies,
-};
-
-static uint32_t cm_t35_keymap[] = {
-	KEY(0, 0, KEY_A),	KEY(0, 1, KEY_B),	KEY(0, 2, KEY_LEFT),
-	KEY(1, 0, KEY_UP),	KEY(1, 1, KEY_ENTER),	KEY(1, 2, KEY_DOWN),
-	KEY(2, 0, KEY_RIGHT),	KEY(2, 1, KEY_C),	KEY(2, 2, KEY_D),
-};
-
-static struct matrix_keymap_data cm_t35_keymap_data = {
-	.keymap			= cm_t35_keymap,
-	.keymap_size		= ARRAY_SIZE(cm_t35_keymap),
-};
-
-static struct twl4030_keypad_data cm_t35_kp_data = {
-	.keymap_data	= &cm_t35_keymap_data,
-	.rows		= 3,
-	.cols		= 3,
-	.rep		= 1,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.deferred	= true,
-	},
-	{
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.transceiver	= 1,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.ocr_mask	= 0x00100000,	/* 3.3V */
-	},
-	{}	/* Terminator */
-};
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 1,
-		.reset_gpio = OMAP_MAX_GPIO_LINES + 6,
-		.vcc_gpio = -EINVAL,
-	},
-	{
-		.port = 2,
-		.reset_gpio = OMAP_MAX_GPIO_LINES + 7,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void  __init cm_t35_init_usbh(void)
-{
-	int err;
-
-	err = gpio_request_one(SB_T35_USB_HUB_RESET_GPIO,
-			       GPIOF_OUT_INIT_LOW, "usb hub rst");
-	if (err) {
-		pr_err("SB-T35: usb hub rst gpio request failed: %d\n", err);
-	} else {
-		udelay(10);
-		gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
-		msleep(1);
-	}
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-}
-
-static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
-				 unsigned ngpio)
-{
-	int wlan_rst = gpio + 2;
-
-	if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
-		gpio_export(wlan_rst, 0);
-		udelay(10);
-		gpio_set_value_cansleep(wlan_rst, 0);
-		udelay(10);
-		gpio_set_value_cansleep(wlan_rst, 1);
-	} else {
-		pr_err("CM-T35: could not obtain gpio for WiFi reset\n");
-	}
-
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data cm_t35_gpio_data = {
-	.setup          = cm_t35_twl_gpio_setup,
-};
-
-static struct twl4030_power_data cm_t35_power_data = {
-	.use_poweroff	= true,
-};
-
-static struct twl4030_platform_data cm_t35_twldata = {
-	/* platform_data for children goes here */
-	.keypad		= &cm_t35_kp_data,
-	.gpio		= &cm_t35_gpio_data,
-	.vmmc1		= &cm_t35_vmmc1,
-	.vsim		= &cm_t35_vsim,
-	.vio		= &cm_t35_vio,
-	.power		= &cm_t35_power_data,
-};
-
-#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
-#include <media/omap3isp.h>
-#include "devices.h"
-
-static struct isp_platform_subdev cm_t35_isp_subdevs[] = {
-	{
-		.board_info = &(struct i2c_board_info){
-			I2C_BOARD_INFO("mt9t001", 0x5d)
-		},
-		.i2c_adapter_id = 3,
-		.bus = &(struct isp_bus_cfg){
-			.interface = ISP_INTERFACE_PARALLEL,
-			.bus = {
-				.parallel = {
-					.clk_pol = 1,
-				},
-			},
-		},
-	},
-	{
-		.board_info = &(struct i2c_board_info){
-			I2C_BOARD_INFO("tvp5150", 0x5c),
-		},
-		.i2c_adapter_id = 3,
-		.bus = &(struct isp_bus_cfg){
-			.interface = ISP_INTERFACE_PARALLEL,
-			.bus = {
-				.parallel = {
-					.clk_pol = 0,
-				},
-			},
-		},
-	},
-	{ 0 },
-};
-
-static struct isp_platform_data cm_t35_isp_pdata = {
-	.subdevs = cm_t35_isp_subdevs,
-};
-
-static struct regulator_consumer_supply cm_t35_camera_supplies[] = {
-	REGULATOR_SUPPLY("vaa", "3-005d"),
-	REGULATOR_SUPPLY("vdd", "3-005d"),
-};
-
-static void __init cm_t35_init_camera(void)
-{
-	struct clk *clk;
-
-	clk = clk_register_fixed_rate(NULL, "mt9t001-clkin", NULL, CLK_IS_ROOT,
-				      48000000);
-	clk_register_clkdev(clk, NULL, "3-005d");
-
-	regulator_register_fixed(2, cm_t35_camera_supplies,
-				 ARRAY_SIZE(cm_t35_camera_supplies));
-
-	if (omap3_init_camera(&cm_t35_isp_pdata) < 0)
-		pr_warn("CM-T3x: Failed registering camera device!\n");
-}
-
-#else
-static inline void cm_t35_init_camera(void) {}
-#endif /* CONFIG_VIDEO_OMAP3 */
-
-static void __init cm_t35_init_i2c(void)
-{
-	omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
-			      TWL_COMMON_REGULATOR_VDAC |
-			      TWL_COMMON_PDATA_AUDIO);
-
-	omap3_pmic_init("tps65930", &cm_t35_twldata);
-
-	omap_register_i2c_bus(3, 400, NULL, 0);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* nCS and IRQ for CM-T35 ethernet */
-	OMAP3_MUX(GPMC_NCS5, OMAP_MUX_MODE0),
-	OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
-	/* nCS and IRQ for SB-T35 ethernet */
-	OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE0),
-	OMAP3_MUX(GPMC_WAIT3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
-
-	/* PENDOWN GPIO */
-	OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
-	/* mUSB */
-	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* MMC 2 */
-	OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-
-	/* McSPI 1 */
-	OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-
-	/* McSPI 4 */
-	OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
-
-	/* McBSP 2 */
-	OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* serial ports */
-	OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
-	OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	/* common DSS */
-	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-
-	/* Camera */
-	OMAP3_MUX(CAM_HS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_VS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_FLD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(CAM_D8, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-	OMAP3_MUX(CAM_D9, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
-	OMAP3_MUX(CAM_STROBE, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	OMAP3_MUX(CAM_D10, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
-	OMAP3_MUX(CAM_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
-
-	/* display controls */
-	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	/* TPS IRQ */
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
-		  OMAP_PIN_INPUT_PULLUP),
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static void __init cm_t3x_common_dss_mux_init(int mux_mode)
-{
-	omap_mux_init_signal("dss_data18", mux_mode);
-	omap_mux_init_signal("dss_data19", mux_mode);
-	omap_mux_init_signal("dss_data20", mux_mode);
-	omap_mux_init_signal("dss_data21", mux_mode);
-	omap_mux_init_signal("dss_data22", mux_mode);
-	omap_mux_init_signal("dss_data23", mux_mode);
-}
-
-static void __init cm_t35_init_mux(void)
-{
-	int mux_mode = OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT;
-
-	omap_mux_init_signal("dss_data0.dss_data0", mux_mode);
-	omap_mux_init_signal("dss_data1.dss_data1", mux_mode);
-	omap_mux_init_signal("dss_data2.dss_data2", mux_mode);
-	omap_mux_init_signal("dss_data3.dss_data3", mux_mode);
-	omap_mux_init_signal("dss_data4.dss_data4", mux_mode);
-	omap_mux_init_signal("dss_data5.dss_data5", mux_mode);
-	cm_t3x_common_dss_mux_init(mux_mode);
-}
-
-static void __init cm_t3730_init_mux(void)
-{
-	int mux_mode = OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT;
-
-	omap_mux_init_signal("sys_boot0", mux_mode);
-	omap_mux_init_signal("sys_boot1", mux_mode);
-	omap_mux_init_signal("sys_boot3", mux_mode);
-	omap_mux_init_signal("sys_boot4", mux_mode);
-	omap_mux_init_signal("sys_boot5", mux_mode);
-	omap_mux_init_signal("sys_boot6", mux_mode);
-	cm_t3x_common_dss_mux_init(mux_mode);
-}
-#else
-static inline void cm_t35_init_mux(void) {}
-static inline void cm_t3730_init_mux(void) {}
-#endif
-
-static void __init cm_t3x_common_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-			     mt46h32m32lf6_sdrc_params);
-	omap_hsmmc_init(mmc);
-	cm_t35_init_i2c();
-	omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
-	cm_t35_init_ethernet();
-	cm_t35_init_led();
-	cm_t35_init_display();
-	omap_twl4030_audio_init("cm-t3x", NULL);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	cm_t35_init_usbh();
-	cm_t35_init_camera();
-}
-
-static void __init cm_t35_init(void)
-{
-	cm_t3x_common_init();
-	cm_t35_init_mux();
-	cm_t35_init_nand();
-}
-
-static void __init cm_t3730_init(void)
-{
-	cm_t3x_common_init();
-	cm_t3730_init_mux();
-}
-
-MACHINE_START(CM_T35, "Compulab CM-T35")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= cm_t35_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(CM_T3730, "Compulab CM-T3730")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3630_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= cm_t3730_init,
-	.init_late     = omap3630_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
deleted file mode 100644
index 81de1c68b360..000000000000
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ /dev/null
@@ -1,595 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3beagle.c
- *
- * Copyright (C) 2008 Texas Instruments
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/pm_opp.h>
-#include <linux/cpu.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/flash.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "common.h"
-#include "omap_device.h"
-#include "gpmc.h"
-#include "soc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "pm.h"
-#include "board-flash.h"
-#include "common-board-devices.h"
-
-#define	NAND_CS	0
-
-static struct pwm_lookup pwm_lookup[] = {
-	/* LEDB -> PMU_STAT */
-	PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat",
-		   7812500, PWM_POLARITY_NORMAL),
-};
-
-static struct led_pwm pwm_leds[] = {
-	{
-		.name		= "beagleboard::pmu_stat",
-		.max_brightness	= 127,
-		.pwm_period_ns	= 7812500,
-	},
-};
-
-static struct led_pwm_platform_data pwm_data = {
-	.num_leds	= ARRAY_SIZE(pwm_leds),
-	.leds		= pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
-	.name	= "leds_pwm",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &pwm_data,
-	},
-};
-
-/*
- * OMAP3 Beagle revision
- * Run time detection of Beagle revision is done by reading GPIO.
- * GPIO ID -
- *	AXBX	= GPIO173, GPIO172, GPIO171: 1 1 1
- *	C1_3	= GPIO173, GPIO172, GPIO171: 1 1 0
- *	C4	= GPIO173, GPIO172, GPIO171: 1 0 1
- *	XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
- *	XMC = GPIO173, GPIO172, GPIO171: 0 1 0
- */
-enum {
-	OMAP3BEAGLE_BOARD_UNKN = 0,
-	OMAP3BEAGLE_BOARD_AXBX,
-	OMAP3BEAGLE_BOARD_C1_3,
-	OMAP3BEAGLE_BOARD_C4,
-	OMAP3BEAGLE_BOARD_XM,
-	OMAP3BEAGLE_BOARD_XMC,
-};
-
-static u8 omap3_beagle_version;
-
-/*
- * Board-specific configuration
- * Defaults to BeagleBoard-xMC
- */
-static struct {
-	int mmc1_gpio_wp;
-	bool usb_pwr_level;	/* 0 - Active Low, 1 - Active High */
-	int dvi_pd_gpio;
-	int usr_button_gpio;
-	int mmc_caps;
-} beagle_config = {
-	.mmc1_gpio_wp = -EINVAL,
-	.usb_pwr_level = 0,
-	.dvi_pd_gpio = -EINVAL,
-	.usr_button_gpio = 4,
-	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-};
-
-static struct gpio omap3_beagle_rev_gpios[] __initdata = {
-	{ 171, GPIOF_IN, "rev_id_0"    },
-	{ 172, GPIOF_IN, "rev_id_1" },
-	{ 173, GPIOF_IN, "rev_id_2"    },
-};
-
-static void __init omap3_beagle_init_rev(void)
-{
-	int ret;
-	u16 beagle_rev = 0;
-
-	omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
-	omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
-	omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
-
-	ret = gpio_request_array(omap3_beagle_rev_gpios,
-				 ARRAY_SIZE(omap3_beagle_rev_gpios));
-	if (ret < 0) {
-		printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
-		omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
-		return;
-	}
-
-	beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)