Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoCs for 3.13.  The diffstat is large,
  mostly because of:

   - Another set of fixes to fix regressions caused by moving OMAP from
     board files to DT.  Tony thinks this was the last major set of
     fixes, with maybe just a few small patches to follow.
   - More fixes for Marvell platforms, most dealing with misdescribed
     PCIe hardware, i.e.  incorrect number of busses on some SoCs, etc.
     The line delta adds up due to various ranges moving around when
     this is fixed.

  But there's also:

   - Some smaller tweaks to defconfigs to make more boards bootable in
     my test setup for better coverage.
   - There are also a few other smaller fixes, a short series for at91,
     a couple of reverts for ux500, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
  arm: socfpga: Enable ARM_TWD for socfpga
  ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
  ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
  ARM: multi_v7_defconfig: enable network for BeagleBone Black
  ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
  ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
  ARM: dts: omap3-beagle: Add omap-twl4030 audio support
  ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
  ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
  ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
  ARM: at91: add usart3 alias to dtsi
  ARM: at91: sama5d3: reduce TWI internal clock frequency
  mmc: omap: Fix I2C dependency and make driver usable with device tree
  mmc: omap: Fix DMA configuration to not rely on device id
  ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
  ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
  ARM: dts: AM33XX IGEP0033: add USB support
  ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
  ARM: dts: AM33XX BASE0033: add pinmux and user led support
  ...

32 files changed, 575 insertions, 114 deletions

diff --git a/Documentation/devicetree/bindings/mmc/ti-omap.txt b/Documentation/devicetree/bindings/mmc/ti-omap.txt
new file mode 100644
index 000000000000..8de579969763
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/ti-omap.txt
@@ -0,0 +1,54 @@
+* TI MMC host controller for OMAP1 and 2420
+
+The MMC Host Controller on TI OMAP1 and 2420 family provides
+an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the omap mmc driver.
+
+Note that this driver will not work with omap2430 or later omaps,
+please see the omap hsmmc driver for the current omaps.
+
+Required properties:
+- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers
+- ti,hwmods: For 2420, must be "msdi<n>", where n is controller
+  instance starting 1
+
+Examples:
+
+	msdi1: mmc@4809c000 {
+		compatible = "ti,omap2420-mmc";
+		ti,hwmods = "msdi1";
+		reg = <0x4809c000 0x80>;
+		interrupts = <83>;
+		dmas = <&sdma 61 &sdma 62>;
+		dma-names = "tx", "rx";
+	};
+
+* TI MMC host controller for OMAP1 and 2420
+
+The MMC Host Controller on TI OMAP1 and 2420 family provides
+an interface for MMC, SD, and SDIO types of memory cards.
+
+This file documents differences between the core properties described
+by mmc.txt and the properties used by the omap mmc driver.
+
+Note that this driver will not work with omap2430 or later omaps,
+please see the omap hsmmc driver for the current omaps.
+
+Required properties:
+- compatible: Must be "ti,omap2420-mmc", for OMAP2420 controllers
+- ti,hwmods: For 2420, must be "msdi<n>", where n is controller
+  instance starting 1
+
+Examples:
+
+	msdi1: mmc@4809c000 {
+		compatible = "ti,omap2420-mmc";
+		ti,hwmods = "msdi1";
+		reg = <0x4809c000 0x80>;
+		interrupts = <83>;
+		dmas = <&sdma 61 &sdma 62>;
+		dma-names = "tx", "rx";
+	};
+
diff --git a/arch/arm/boot/dts/am335x-base0033.dts b/arch/arm/boot/dts/am335x-base0033.dts
index b4f95c2bbf74..72a9b3fc4251 100644
--- a/arch/arm/boot/dts/am335x-base0033.dts
+++ b/arch/arm/boot/dts/am335x-base0033.dts
@@ -13,4 +13,83 @@
 / {
 	model = "IGEP COM AM335x on AQUILA Expansion";
 	compatible = "isee,am335x-base0033", "isee,am335x-igep0033", "ti,am33xx";
+
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_pins>;
+		pinctrl-1 = <&nxp_hdmi_off_pins>;
+		status = "okay";
+	};
+
+	leds_base {
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_base_pins>;
+
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "base:red:user";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;	/* gpio1_21 */
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "base:green:user";
+			gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;	/* gpio2_0 */
+			default-state = "off";
+		};
+	};
+};
+
+&am33xx_pinmux {
+	nxp_hdmi_pins: pinmux_nxp_hdmi_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+			0xa0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data0 */
+			0xa4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data1 */
+			0xa8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data2 */
+			0xac (PIN_OUTPUT | MUX_MODE0)	/* lcd_data3 */
+			0xb0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data4 */
+			0xb4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data5 */
+			0xb8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data6 */
+			0xbc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data7 */
+			0xc0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data8 */
+			0xc4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data9 */
+			0xc8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data10 */
+			0xcc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data11 */
+			0xd0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data12 */
+			0xd4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data13 */
+			0xd8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_data14 */
+			0xdc (PIN_OUTPUT | MUX_MODE0)	/* lcd_data15 */
+			0xe0 (PIN_OUTPUT | MUX_MODE0)	/* lcd_vsync */
+			0xe4 (PIN_OUTPUT | MUX_MODE0)	/* lcd_hsync */
+			0xe8 (PIN_OUTPUT | MUX_MODE0)	/* lcd_pclk */
+			0xec (PIN_OUTPUT | MUX_MODE0)	/* lcd_ac_bias_en */
+		>;
+	};
+	nxp_hdmi_off_pins: pinmux_nxp_hdmi_off_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_OUTPUT | MUX_MODE3)	/* xdma_event_intr0.clkout1 */
+		>;
+	};
+
+	leds_base_pins: pinmux_leds_base_pins {
+		pinctrl-single,pins = <
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			0x88 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.gpio2_0 */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+};
+
+&i2c0 {
+	eeprom: eeprom@50 {
+		compatible = "at,24c256";
+		reg = <0x50>;
+	};
 };
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
index 619624479311..7063311a58d9 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -199,6 +199,35 @@
 	pinctrl-0 = <&uart0_pins>;
 };
 
+&usb {
+	status = "okay";
+
+	control@44e10000 {
+		status = "okay";
+	};
+
+	usb-phy@47401300 {
+		status = "okay";
+	};
+
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
+	usb@47401000 {
+		status = "okay";
+	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
+
+	dma-controller@07402000  {
+		status = "okay";
+	};
+};
+
 #include "tps65910.dtsi"
 
 &tps {
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 90ce29dbe119..08a56bcfc724 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -99,22 +99,22 @@
 					spi-max-frequency = <50000000>;
 				};
 			};
+		};
 
-			pcie-controller {
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * both standard PCIe slots and mini-PCIe
+			 * slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
 				status = "okay";
-				/*
-				 * The two PCIe units are accessible through
-				 * both standard PCIe slots and mini-PCIe
-				 * slots on the board.
-				 */
-				pcie@1,0 {
-					/* Port 0, Lane 0 */
-					status = "okay";
-				};
-				pcie@2,0 {
-					/* Port 1, Lane 0 */
-					status = "okay";
-				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi
index 00d6a798c705..7f10f627ae5b 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/armada-370-xp.dtsi
@@ -118,7 +118,7 @@
 
 			coherency-fabric@20200 {
 				compatible = "marvell,coherency-fabric";
-				reg = <0x20200 0xb0>, <0x21810 0x1c>;
+				reg = <0x20200 0xb0>, <0x21010 0x1c>;
 			};
 
 			serial@12000 {
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 3f5e6121c730..98335fb34b7a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -47,7 +47,7 @@
 		/*
 		 * MV78230 has 2 PCIe units Gen2.0: One unit can be
 		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
+		 * x1 only.
 		 */
 		pcie-controller {
 			compatible = "marvell,armada-xp-pcie";
@@ -62,10 +62,10 @@
 
 			ranges =
 			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000   /* Port 0.0 registers */
-				0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000   /* Port 2.0 registers */
 				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000   /* Port 0.1 registers */
 				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
 				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
+				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
 				0x82000000 0x1 0       MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
 				0x81000000 0x1 0       MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
 				0x82000000 0x2 0       MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
@@ -74,8 +74,8 @@
 				0x81000000 0x3 0       MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
 				0x82000000 0x4 0       MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
 				0x81000000 0x4 0       MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
-				0x82000000 0x9 0       MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
-				0x81000000 0x9 0       MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */>;
+				0x82000000 0x5 0       MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0       MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */>;
 
 			pcie@1,0 {
 				device_type = "pci";
@@ -145,20 +145,20 @@
 				status = "disabled";
 			};
 
-			pcie@9,0 {
+			pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
-					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
+				clocks = <&gateclk 9>;
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 3e9fd1353f89..66609684d41b 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -48,7 +48,7 @@
 		/*
 		 * MV78260 has 3 PCIe units Gen2.0: Two units can be
 		 * configured as x4 or quad x1 lanes. One unit is
-		 * x4/x1.
+		 * x4 only.
 		 */
 		pcie-controller {
 			compatible = "marvell,armada-xp-pcie";
@@ -68,7 +68,9 @@
 				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000   /* Port 0.2 registers */
 				0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000   /* Port 0.3 registers */
 				0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000   /* Port 1.0 registers */
-				0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000   /* Port 3.0 registers */
+				0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000   /* Port 1.1 registers */
+				0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000   /* Port 1.2 registers */
+				0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000   /* Port 1.3 registers */
 				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
 				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO  */
 				0x82000000 0x2 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
@@ -77,10 +79,18 @@
 				0x81000000 0x3 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO  */
 				0x82000000 0x4 0     MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
 				0x81000000 0x4 0     MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO  */
-				0x82000000 0x9 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
-				0x81000000 0x9 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
-				0x82000000 0xa 0     MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
-				0x81000000 0xa 0     MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO  */>;
+
+				0x82000000 0x5 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+				0x81000000 0x5 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO  */
+				0x82000000 0x6 0     MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+				0x81000000 0x6 0     MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO  */
+				0x82000000 0x7 0     MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+				0x81000000 0x7 0     MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO  */
+				0x82000000 0x8 0     MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+				0x81000000 0x8 0     MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO  */
+
+				0x82000000 0x9 0     MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+				0x81000000 0x9 0     MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO  */>;
 
 			pcie@1,0 {
 				device_type = "pci";
@@ -106,8 +116,8 @@
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-                                ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
-                                          0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
 				interrupt-map = <0 0 0 0 &mpic 59>;
 				marvell,pcie-port = <0>;
@@ -150,37 +160,88 @@
 				status = "disabled";
 			};
 
-			pcie@9,0 {
+			pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
-				reg = <0x4800 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
-					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
-				marvell,pcie-port = <2>;
+				interrupt-map = <0 0 0 0 &mpic 62>;
+				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 26>;
+				clocks = <&gateclk 9>;
 				status = "disabled";
 			};
 
-			pcie@10,0 {
+			pcie@6,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
-				reg = <0x5000 0 0 0 0>;
+				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
 				#interrupt-cells = <1>;
-				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
-					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
+				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
-				marvell,pcie-port = <3>;
+				interrupt-map = <0 0 0 0 &mpic 63>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 10>;
+				status = "disabled";
+			};
+
+			pcie@7,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				reg = <0x3800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 64>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <2>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			pcie@8,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				reg = <0x4000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 65>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <3>;
+				clocks = <&gateclk 12>;
+				status = "disabled";
+			};
+
+			pcie@9,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				reg = <0x4800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &mpic 99>;
+				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
-				clocks = <&gateclk 27>;
+				clocks = <&gateclk 26>;
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
index 2347e9563cef..6801106fa1f8 100644
--- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
@@ -11,6 +11,10 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	aliases {
+		serial4 = &usart3;
+	};
+
 	ahb {
 		apb {
 			pinctrl@fffff400 {
diff --git a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
index 9c18adf788f7..f577b7df9a29 100644
--- a/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
+++ b/arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi
@@ -44,8 +44,8 @@
 		gpmc,wr-access-ns = <186>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vmmc-supply = <&vddvario>;
-		vmmc_aux-supply = <&vdd33a>;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 31a632f7effb..df33a50bc070 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -215,3 +215,10 @@
 &usbhsehci {
 	phys = <0 &hsusb2_phy>;
 };
+
+&vaux2 {
+	regulator-name = "usb_1v8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index fa532aaacc68..3ba4a625ea5b 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -61,6 +61,14 @@
 		vcc-supply = <&hsusb2_power>;
 	};
 
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "omap3beagle";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 
@@ -120,6 +128,12 @@
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
 	};
 };
 
@@ -178,3 +192,10 @@
 	mode = <3>;
 	power = <50>;
 };
+
+&vaux2 {
+	regulator-name = "vdd_ehci";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+};
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index ba1e58b7b7e3..165aaf7591ba 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for IGEP Technology devices
+ * Common device tree for IGEP boards based on AM/DM37x
  *
  * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
@@ -10,7 +10,7 @@
  */
 /dts-v1/;
 
-#include "omap34xx.dtsi"
+#include "omap36xx.dtsi"
 
 / {
 	memory {
@@ -24,6 +24,25 @@
 		ti,mcbsp = <&mcbsp2>;
 		ti,codec = <&twl_audio>;
 	};
+
+	vdd33: regulator-vdd33 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33";
+		regulator-always-on;
+	};
+
+	lbee1usjyc_vmmc: lbee1usjyc_vmmc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lbee1usjyc_pins>;
+		compatible = "regulator-fixed";
+		regulator-name = "regulator-lbee1usjyc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>;	/* gpio_138 WIFI_PDN */
+		startup-delay-us = <10000>;
+		enable-active-high;
+		vin-supply = <&vdd33>;
+	};
 };
 
 &omap3_pmx_core {
@@ -48,6 +67,15 @@
 		>;
 	};
 
+	/* WiFi/BT combo */
+	lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
+		pinctrl-single,pins = <
+			0x136 (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 */
+			0x138 (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat6.gpio_138 */
+			0x13a (PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat7.gpio_139 */
+		>;
+	};
+
 	mcbsp2_pins: pinmux_mcbsp2_pins {
 		pinctrl-single,pins = <
 			0x10c (PIN_INPUT | MUX_MODE0)		/* mcbsp2_fsx.mcbsp2_fsx */
@@ -65,10 +93,17 @@
 			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
 			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
 			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
-			0x120 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat4.sdmmc1_dat4 */
-			0x122 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat5.sdmmc1_dat5 */
-			0x124 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat6.sdmmc1_dat6 */
-			0x126 (PIN_INPUT | MUX_MODE0)		/* sdmmc1_dat7.sdmmc1_dat7 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc2_dat0.sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;
 	};
 
@@ -78,10 +113,33 @@
 		>;
 	};
 
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x18a (PIN_INPUT | MUX_MODE0)   /* i2c1_scl.i2c1_scl */
+			0x18c (PIN_INPUT | MUX_MODE0)   /* i2c1_sda.i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x18e (PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
+			0x190 (PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x192 (PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
+			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
+		>;
+	};
+
 	leds_pins: pinmux_leds_pins { };
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <2600000>;
 
 	twl: twl@48 {
@@ -101,9 +159,16 @@
 #include "twl4030_omap3.dtsi"
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+};
+
 &mcbsp2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
@@ -114,11 +179,15 @@
       pinctrl-0 = <&mmc1_pins>;
       vmmc-supply = <&vmmc1>;
       vmmc_aux-supply = <&vsim>;
-      bus-width = <8>;
+      bus-width = <4>;
 };
 
 &mmc2 {
-	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&lbee1usjyc_vmmc>;
+	bus-width = <4>;
+	non-removable;
 };
 
 &mmc3 {
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index d5cc79267250..1c7e74d2d2bc 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -1,5 +1,5 @@
 /*
- * Device Tree Source for IGEPv2 board
+ * Device Tree Source for IGEPv2 Rev. (TI OMAP AM/DM37x)
  *
  * Copyright (C) 2012 Javier Martinez Canillas <javier@collabora.co.uk>
  * Copyright (C) 2012 Enric Balletbo i Serra <eballetbo@gmail.com>
@@ -13,7 +13,7 @@
 #include "omap-gpmc-smsc911x.dtsi"
 
 / {
-	model = "IGEPv2";
+	model = "IGEPv2 (TI OMAP AM/DM37x)";
 	compatible = "isee,o