Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can-next

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

27 files changed, 1488 insertions, 60 deletions

diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index b56bd9e80957..1cca19f1c490 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -1,9 +1,7 @@
 menu "CAN Device Drivers"
-	depends on CAN
 
 config CAN_VCAN
 	tristate "Virtual Local CAN Interface (vcan)"
-	depends on CAN
 	---help---
 	  Similar to the network loopback devices, vcan offers a
 	  virtual local CAN interface.
@@ -13,7 +11,6 @@ config CAN_VCAN
 
 config CAN_SLCAN
 	tristate "Serial / USB serial CAN Adaptors (slcan)"
-	depends on CAN
 	---help---
 	  CAN driver for several 'low cost' CAN interfaces that are attached
 	  via serial lines or via USB-to-serial adapters using the LAWICEL
@@ -33,16 +30,16 @@ config CAN_SLCAN
 
 config CAN_DEV
 	tristate "Platform CAN drivers with Netlink support"
-	depends on CAN
 	default y
 	---help---
 	  Enables the common framework for platform CAN drivers with Netlink
 	  support. This is the standard library for CAN drivers.
 	  If unsure, say Y.
 
+if CAN_DEV
+
 config CAN_CALC_BITTIMING
 	bool "CAN bit-timing calculation"
-	depends on CAN_DEV
 	default y
 	---help---
 	  If enabled, CAN bit-timing parameters will be calculated for the
@@ -54,15 +51,26 @@ config CAN_CALC_BITTIMING
 	  arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
 	  If unsure, say Y.
 
+config CAN_LEDS
+	bool "Enable LED triggers for Netlink based drivers"
+	depends on LEDS_CLASS
+	select LEDS_TRIGGERS
+	---help---
+	  This option adds two LED triggers for packet receive and transmit
+	  events on each supported CAN device.
+
+	  Say Y here if you are working on a system with led-class supported
+	  LEDs and you want to use them as canbus activity indicators.
+
 config CAN_AT91
 	tristate "Atmel AT91 onchip CAN controller"
-	depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5)
+	depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9X5
 	---help---
 	  This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
 	  and AT91SAM9X5 processors.
 
 config CAN_TI_HECC
-	depends on CAN_DEV && ARCH_OMAP3
+	depends on ARCH_OMAP3
 	tristate "TI High End CAN Controller"
 	---help---
 	  Driver for TI HECC (High End CAN Controller) module found on many
@@ -70,12 +78,12 @@ config CAN_TI_HECC
 
 config CAN_MCP251X
 	tristate "Microchip MCP251x SPI CAN controllers"
-	depends on CAN_DEV && SPI && HAS_DMA
+	depends on SPI && HAS_DMA
 	---help---
 	  Driver for the Microchip MCP251x SPI CAN controllers.
 
 config CAN_BFIN
-	depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
+	depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
 	tristate "Analog Devices Blackfin on-chip CAN"
 	---help---
 	  Driver for the Analog Devices Blackfin on-chip CAN controllers
@@ -85,7 +93,7 @@ config CAN_BFIN
 
 config CAN_JANZ_ICAN3
 	tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
-	depends on CAN_DEV && MFD_JANZ_CMODIO
+	depends on MFD_JANZ_CMODIO
 	---help---
 	  Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
 	  connects to a MODULbus carrier board.
@@ -98,13 +106,13 @@ config HAVE_CAN_FLEXCAN
 
 config CAN_FLEXCAN
 	tristate "Support for Freescale FLEXCAN based chips"
-	depends on CAN_DEV && HAVE_CAN_FLEXCAN
+	depends on HAVE_CAN_FLEXCAN
 	---help---
 	  Say Y here if you want to support for Freescale FlexCAN.
 
 config PCH_CAN
 	tristate "Intel EG20T PCH CAN controller"
-	depends on CAN_DEV && PCI
+	depends on PCI
 	---help---
 	  This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
 	  is an IOH for x86 embedded processor (Intel Atom E6xx series).
@@ -112,7 +120,7 @@ config PCH_CAN
 
 config CAN_GRCAN
 	tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
-	depends on CAN_DEV && OF
+	depends on OF
 	---help---
 	  Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
 	  Note that the driver supports little endian, even though little
@@ -131,9 +139,10 @@ source "drivers/net/can/usb/Kconfig"
 
 source "drivers/net/can/softing/Kconfig"
 
+endif
+
 config CAN_DEBUG_DEVICES
 	bool "CAN devices debugging messages"
-	depends on CAN
 	---help---
 	  Say Y here if you want the CAN device drivers to produce a bunch of
 	  debug messages to the system log.  Select this if you are having
diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile
index 7de59862bbe9..c7440392adbb 100644
--- a/drivers/net/can/Makefile
+++ b/drivers/net/can/Makefile
@@ -8,6 +8,8 @@ obj-$(CONFIG_CAN_SLCAN)		+= slcan.o
 obj-$(CONFIG_CAN_DEV)		+= can-dev.o
 can-dev-y			:= dev.o
 
+can-dev-$(CONFIG_CAN_LEDS)	+= led.o
+
 obj-y				+= usb/
 obj-y				+= softing/
 
diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c
index 81baefda037b..44f363792b59 100644
--- a/drivers/net/can/at91_can.c
+++ b/drivers/net/can/at91_can.c
@@ -37,6 +37,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #define AT91_MB_MASK(i)		((1 << (i)) - 1)
 
@@ -641,6 +642,8 @@ static void at91_read_msg(struct net_device *dev, unsigned int mb)
 
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
+
+	can_led_event(dev, CAN_LED_EVENT_RX);
 }
 
 /**
@@ -875,6 +878,7 @@ static void at91_irq_tx(struct net_device *dev, u32 reg_sr)
 			/* _NOTE_: subtract AT91_MB_TX_FIRST offset from mb! */
 			can_get_echo_skb(dev, mb - get_mb_tx_first(priv));
 			dev->stats.tx_packets++;
+			can_led_event(dev, CAN_LED_EVENT_TX);
 		}
 	}
 
@@ -1128,6 +1132,8 @@ static int at91_open(struct net_device *dev)
 		goto out_close;
 	}
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	/* start chip and queuing */
 	at91_chip_start(dev);
 	napi_enable(&priv->napi);
@@ -1159,6 +1165,8 @@ static int at91_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1321,6 +1329,8 @@ static int at91_can_probe(struct platform_device *pdev)
 		goto exit_free;
 	}
 
+	devm_can_led_init(dev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
 		 priv->reg_base, dev->irq);
 
diff --git a/drivers/net/can/c_can/Kconfig b/drivers/net/can/c_can/Kconfig
index 3b83bafcd947..61ffc12d8fd8 100644
--- a/drivers/net/can/c_can/Kconfig
+++ b/drivers/net/can/c_can/Kconfig
@@ -1,6 +1,6 @@
 menuconfig CAN_C_CAN
 	tristate "Bosch C_CAN/D_CAN devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_C_CAN
 
diff --git a/drivers/net/can/c_can/c_can.c b/drivers/net/can/c_can/c_can.c
index 5233b8f58d77..57eb1e77865d 100644
--- a/drivers/net/can/c_can/c_can.c
+++ b/drivers/net/can/c_can/c_can.c
@@ -39,6 +39,7 @@
 #include <linux/can.h>
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #include "c_can.h"
 
@@ -477,6 +478,8 @@ static int c_can_read_msg_object(struct net_device *dev, int iface, int ctrl)
 	stats->rx_packets++;
 	stats->rx_bytes += frame->can_dlc;
 
+	can_led_event(dev, CAN_LED_EVENT_RX);
+
 	return 0;
 }
 
@@ -751,6 +754,7 @@ static void c_can_do_tx(struct net_device *dev)
 					C_CAN_IFACE(MSGCTRL_REG, 0))
 					& IF_MCONT_DLC_MASK;
 			stats->tx_packets++;
+			can_led_event(dev, CAN_LED_EVENT_TX);
 			c_can_inval_msg_object(dev, 0, msg_obj_no);
 		} else {
 			break;
@@ -1115,6 +1119,8 @@ static int c_can_open(struct net_device *dev)
 
 	napi_enable(&priv->napi);
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	/* start the c_can controller */
 	c_can_start(dev);
 
@@ -1143,6 +1149,8 @@ static int c_can_close(struct net_device *dev)
 	c_can_reset_ram(priv, false);
 	c_can_pm_runtime_put_sync(priv);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1268,6 +1276,8 @@ int register_c_can_dev(struct net_device *dev)
 	err = register_candev(dev);
 	if (err)
 		c_can_pm_runtime_disable(priv);
+	else
+		devm_can_led_init(dev);
 
 	return err;
 }
diff --git a/drivers/net/can/cc770/Kconfig b/drivers/net/can/cc770/Kconfig
index 22c07a8c8b43..6a9a5ba79220 100644
--- a/drivers/net/can/cc770/Kconfig
+++ b/drivers/net/can/cc770/Kconfig
@@ -1,6 +1,6 @@
 menuconfig CAN_CC770
 	tristate "Bosch CC770 and Intel AN82527 devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_CC770
 
diff --git a/drivers/net/can/dev.c b/drivers/net/can/dev.c
index 8233e5ed2939..59ada082a994 100644
--- a/drivers/net/can/dev.c
+++ b/drivers/net/can/dev.c
@@ -24,7 +24,9 @@
 #include <linux/if_arp.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>
+#include <linux/can/skb.h>
 #include <linux/can/netlink.h>
+#include <linux/can/led.h>
 #include <net/rtnetlink.h>
 
 #define MOD_DESC "CAN device driver interface"
@@ -501,13 +503,18 @@ struct sk_buff *alloc_can_skb(struct net_device *dev, struct can_frame **cf)
 {
 	struct sk_buff *skb;
 
-	skb = netdev_alloc_skb(dev, sizeof(struct can_frame));
+	skb = netdev_alloc_skb(dev, sizeof(struct can_skb_priv) +
+			       sizeof(struct can_frame));
 	if (unlikely(!skb))
 		return NULL;
 
 	skb->protocol = htons(ETH_P_CAN);
 	skb->pkt_type = PACKET_BROADCAST;
 	skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = dev->ifindex;
+
 	*cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame));
 	memset(*cf, 0, sizeof(struct can_frame));
 
@@ -794,10 +801,25 @@ void unregister_candev(struct net_device *dev)
 }
 EXPORT_SYMBOL_GPL(unregister_candev);
 
+/*
+ * Test if a network device is a candev based device
+ * and return the can_priv* if so.
+ */
+struct can_priv *safe_candev_priv(struct net_device *dev)
+{
+	if ((dev->type != ARPHRD_CAN) || (dev->rtnl_link_ops != &can_link_ops))
+		return NULL;
+
+	return netdev_priv(dev);
+}
+EXPORT_SYMBOL_GPL(safe_candev_priv);
+
 static __init int can_dev_init(void)
 {
 	int err;
 
+	can_led_notifier_init();
+
 	err = rtnl_link_register(&can_link_ops);
 	if (!err)
 		printk(KERN_INFO MOD_DESC "\n");
@@ -809,6 +831,8 @@ module_init(can_dev_init);
 static __exit void can_dev_exit(void)
 {
 	rtnl_link_unregister(&can_link_ops);
+
+	can_led_notifier_exit();
 }
 module_exit(can_dev_exit);
 
diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c
index 0289a6d86f66..769d29ed106d 100644
--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -23,6 +23,7 @@
 #include <linux/can.h>
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/flexcan.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
@@ -564,6 +565,8 @@ static int flexcan_read_frame(struct net_device *dev)
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
 
+	can_led_event(dev, CAN_LED_EVENT_RX);
+
 	return 1;
 }
 
@@ -652,6 +655,7 @@ static irqreturn_t flexcan_irq(int irq, void *dev_id)
 	if (reg_iflag1 & (1 << FLEXCAN_TX_BUF_ID)) {
 		stats->tx_bytes += can_get_echo_skb(dev, 0);
 		stats->tx_packets++;
+		can_led_event(dev, CAN_LED_EVENT_TX);
 		flexcan_write((1 << FLEXCAN_TX_BUF_ID), &regs->iflag1);
 		netif_wake_queue(dev);
 	}
@@ -865,6 +869,9 @@ static int flexcan_open(struct net_device *dev)
 	err = flexcan_chip_start(dev);
 	if (err)
 		goto out_close;
+
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	napi_enable(&priv->napi);
 	netif_start_queue(dev);
 
@@ -893,6 +900,8 @@ static int flexcan_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -1092,6 +1101,8 @@ static int flexcan_probe(struct platform_device *pdev)
 		goto failed_register;
 	}
 
+	devm_can_led_init(dev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n",
 		 priv->base, dev->irq);
 
diff --git a/drivers/net/can/led.c b/drivers/net/can/led.c
new file mode 100644
index 000000000000..f27fca65dc4a
--- /dev/null
+++ b/drivers/net/can/led.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright 2012, Fabio Baltieri <fabio.baltieri@gmail.com>
+ * Copyright 2012, Kurt Van Dijck <kurt.van.dijck@eia.be>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/netdevice.h>
+#include <linux/can/dev.h>
+
+#include <linux/can/led.h>
+
+static unsigned long led_delay = 50;
+module_param(led_delay, ulong, 0644);
+MODULE_PARM_DESC(led_delay,
+		"blink delay time for activity leds (msecs, default: 50).");
+
+/* Trigger a LED event in response to a CAN device event */
+void can_led_event(struct net_device *netdev, enum can_led_event event)
+{
+	struct can_priv *priv = netdev_priv(netdev);
+
+	switch (event) {
+	case CAN_LED_EVENT_OPEN:
+		led_trigger_event(priv->tx_led_trig, LED_FULL);
+		led_trigger_event(priv->rx_led_trig, LED_FULL);
+		break;
+	case CAN_LED_EVENT_STOP:
+		led_trigger_event(priv->tx_led_trig, LED_OFF);
+		led_trigger_event(priv->rx_led_trig, LED_OFF);
+		break;
+	case CAN_LED_EVENT_TX:
+		if (led_delay)
+			led_trigger_blink_oneshot(priv->tx_led_trig,
+						  &led_delay, &led_delay, 1);
+		break;
+	case CAN_LED_EVENT_RX:
+		if (led_delay)
+			led_trigger_blink_oneshot(priv->rx_led_trig,
+						  &led_delay, &led_delay, 1);
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(can_led_event);
+
+static void can_led_release(struct device *gendev, void *res)
+{
+	struct can_priv *priv = netdev_priv(to_net_dev(gendev));
+
+	led_trigger_unregister_simple(priv->tx_led_trig);
+	led_trigger_unregister_simple(priv->rx_led_trig);
+}
+
+/* Register CAN LED triggers for a CAN device
+ *
+ * This is normally called from a driver's probe function
+ */
+void devm_can_led_init(struct net_device *netdev)
+{
+	struct can_priv *priv = netdev_priv(netdev);
+	void *res;
+
+	res = devres_alloc(can_led_release, 0, GFP_KERNEL);
+	if (!res) {
+		netdev_err(netdev, "cannot register LED triggers\n");
+		return;
+	}
+
+	snprintf(priv->tx_led_trig_name, sizeof(priv->tx_led_trig_name),
+		 "%s-tx", netdev->name);
+	snprintf(priv->rx_led_trig_name, sizeof(priv->rx_led_trig_name),
+		 "%s-rx", netdev->name);
+
+	led_trigger_register_simple(priv->tx_led_trig_name,
+				    &priv->tx_led_trig);
+	led_trigger_register_simple(priv->rx_led_trig_name,
+				    &priv->rx_led_trig);
+
+	devres_add(&netdev->dev, res);
+}
+EXPORT_SYMBOL_GPL(devm_can_led_init);
+
+/* NETDEV rename notifier to rename the associated led triggers too */
+static int can_led_notifier(struct notifier_block *nb, unsigned long msg,
+			void *data)
+{
+	struct net_device *netdev = data;
+	struct can_priv *priv = safe_candev_priv(netdev);
+	char name[CAN_LED_NAME_SZ];
+
+	if (!priv)
+		return NOTIFY_DONE;
+
+	if (msg == NETDEV_CHANGENAME) {
+		snprintf(name, sizeof(name), "%s-tx", netdev->name);
+		led_trigger_rename_static(name, priv->tx_led_trig);
+
+		snprintf(name, sizeof(name), "%s-rx", netdev->name);
+		led_trigger_rename_static(name, priv->rx_led_trig);
+	}
+
+	return NOTIFY_DONE;
+}
+
+/* notifier block for netdevice event */
+static struct notifier_block can_netdev_notifier __read_mostly = {
+	.notifier_call = can_led_notifier,
+};
+
+int __init can_led_notifier_init(void)
+{
+	return register_netdevice_notifier(&can_netdev_notifier);
+}
+
+void __exit can_led_notifier_exit(void)
+{
+	unregister_netdevice_notifier(&can_netdev_notifier);
+}
diff --git a/drivers/net/can/mcp251x.c b/drivers/net/can/mcp251x.c
index 5eaf47b8e37b..f32b9fc6a983 100644
--- a/drivers/net/can/mcp251x.c
+++ b/drivers/net/can/mcp251x.c
@@ -60,6 +60,7 @@
 
 #include <linux/can/core.h>
 #include <linux/can/dev.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/mcp251x.h>
 #include <linux/completion.h>
 #include <linux/delay.h>
@@ -494,6 +495,9 @@ static void mcp251x_hw_rx(struct spi_device *spi, int buf_idx)
 
 	priv->net->stats.rx_packets++;
 	priv->net->stats.rx_bytes += frame->can_dlc;
+
+	can_led_event(priv->net, CAN_LED_EVENT_RX);
+
 	netif_rx_ni(skb);
 }
 
@@ -707,6 +711,8 @@ static int mcp251x_stop(struct net_device *net)
 
 	mutex_unlock(&priv->mcp_lock);
 
+	can_led_event(net, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -905,6 +911,7 @@ static irqreturn_t mcp251x_can_ist(int irq, void *dev_id)
 		if (intf & CANINTF_TX) {
 			net->stats.tx_packets++;
 			net->stats.tx_bytes += priv->tx_len - 1;
+			can_led_event(net, CAN_LED_EVENT_TX);
 			if (priv->tx_len) {
 				can_get_echo_skb(net, 0);
 				priv->tx_len = 0;
@@ -968,6 +975,9 @@ static int mcp251x_open(struct net_device *net)
 		mcp251x_open_clean(net);
 		goto open_unlock;
 	}
+
+	can_led_event(net, CAN_LED_EVENT_OPEN);
+
 	netif_wake_queue(net);
 
 open_unlock:
@@ -1077,10 +1087,15 @@ static int mcp251x_can_probe(struct spi_device *spi)
 		pdata->transceiver_enable(0);
 
 	ret = register_candev(net);
-	if (!ret) {
-		dev_info(&spi->dev, "probed\n");
-		return ret;
-	}
+	if (ret)
+		goto error_probe;
+
+	devm_can_led_init(net);
+
+	dev_info(&spi->dev, "probed\n");
+
+	return ret;
+
 error_probe:
 	if (!mcp251x_enable_dma)
 		kfree(priv->spi_rx_buf);
diff --git a/drivers/net/can/mscan/Kconfig b/drivers/net/can/mscan/Kconfig
index d38706958af6..f19be5269e7b 100644
--- a/drivers/net/can/mscan/Kconfig
+++ b/drivers/net/can/mscan/Kconfig
@@ -1,5 +1,5 @@
 config CAN_MSCAN
-	depends on CAN_DEV && (PPC || M68K)
+	depends on PPC || M68K
 	tristate "Support for Freescale MSCAN based chips"
 	---help---
 	  The Motorola Scalable Controller Area Network (MSCAN) definition
diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig
index 92f73c708a3d..b39ca5b3ea7f 100644
--- a/drivers/net/can/sja1000/Kconfig
+++ b/drivers/net/can/sja1000/Kconfig
@@ -1,6 +1,6 @@
 menuconfig CAN_SJA1000
 	tristate "Philips/NXP SJA1000 devices"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 
 if CAN_SJA1000
 
@@ -99,11 +99,11 @@ config CAN_TSCAN1
 	tristate "TS-CAN1 PC104 boards"
 	depends on ISA
 	help
-	This driver is for Technologic Systems' TSCAN-1 PC104 boards.
-	http://www.embeddedarm.com/products/board-detail.php?product=TS-CAN1
-	The driver supports multiple boards and automatically configures them:
-	PLD IO base addresses are read from jumpers JP1 and JP2,
-	IRQ numbers are read from jumpers JP4 and JP5,
-	SJA1000 IO base addresses are chosen heuristically (first that works).
+	  This driver is for Technologic Systems' TSCAN-1 PC104 boards.
+	  http://www.embeddedarm.com/products/board-detail.php?product=TS-CAN1
+	  The driver supports multiple boards and automatically configures them:
+	  PLD IO base addresses are read from jumpers JP1 and JP2,
+	  IRQ numbers are read from jumpers JP4 and JP5,
+	  SJA1000 IO base addresses are chosen heuristically (first that works).
 
 endif
diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c
index 83ee11eca0e2..daf4013a8fc7 100644
--- a/drivers/net/can/sja1000/sja1000.c
+++ b/drivers/net/can/sja1000/sja1000.c
@@ -60,6 +60,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 
 #include "sja1000.h"
 
@@ -368,6 +369,8 @@ static void sja1000_rx(struct net_device *dev)
 
 	stats->rx_packets++;
 	stats->rx_bytes += cf->can_dlc;
+
+	can_led_event(dev, CAN_LED_EVENT_RX);
 }
 
 static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
@@ -521,6 +524,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 				can_get_echo_skb(dev, 0);
 			}
 			netif_wake_queue(dev);
+			can_led_event(dev, CAN_LED_EVENT_TX);
 		}
 		if (isrc & IRQ_RI) {
 			/* receive interrupt */
@@ -575,6 +579,8 @@ static int sja1000_open(struct net_device *dev)
 	/* init and start chi */
 	sja1000_start(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_OPEN);
+
 	netif_start_queue(dev);
 
 	return 0;
@@ -592,6 +598,8 @@ static int sja1000_close(struct net_device *dev)
 
 	close_candev(dev);
 
+	can_led_event(dev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -639,6 +647,8 @@ static const struct net_device_ops sja1000_netdev_ops = {
 
 int register_sja1000dev(struct net_device *dev)
 {
+	int ret;
+
 	if (!sja1000_probe_chip(dev))
 		return -ENODEV;
 
@@ -648,7 +658,12 @@ int register_sja1000dev(struct net_device *dev)
 	set_reset_mode(dev);
 	chipset_init(dev);
 
-	return register_candev(dev);
+	ret =  register_candev(dev);
+
+	if (!ret)
+		devm_can_led_init(dev);
+
+	return ret;
 }
 EXPORT_SYMBOL_GPL(register_sja1000dev);
 
diff --git a/drivers/net/can/slcan.c b/drivers/net/can/slcan.c
index adc3708d8829..e79a8d10e0fc 100644
--- a/drivers/net/can/slcan.c
+++ b/drivers/net/can/slcan.c
@@ -55,6 +55,7 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/can.h>
+#include <linux/can/skb.h>
 
 static __initconst const char banner[] =
 	KERN_INFO "slcan: serial line CAN interface driver\n";
@@ -184,7 +185,8 @@ static void slc_bump(struct slcan *sl)
 		cf.data[i] |= tmp;
 	}
 
-	skb = dev_alloc_skb(sizeof(struct can_frame));
+	skb = dev_alloc_skb(sizeof(struct can_frame) +
+			    sizeof(struct can_skb_priv));
 	if (!skb)
 		return;
 
@@ -192,6 +194,10 @@ static void slc_bump(struct slcan *sl)
 	skb->protocol = htons(ETH_P_CAN);
 	skb->pkt_type = PACKET_BROADCAST;
 	skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+	skb_reserve(skb, sizeof(struct can_skb_priv));
+	((struct can_skb_priv *)(skb->head))->ifindex = sl->dev->ifindex;
+
 	memcpy(skb_put(skb, sizeof(struct can_frame)),
 	       &cf, sizeof(struct can_frame));
 	netif_rx_ni(skb);
diff --git a/drivers/net/can/softing/Kconfig b/drivers/net/can/softing/Kconfig
index 5de46a9a77bb..96b6fe158b5b 100644
--- a/drivers/net/can/softing/Kconfig
+++ b/drivers/net/can/softing/Kconfig
@@ -1,6 +1,6 @@
 config CAN_SOFTING
 	tristate "Softing Gmbh CAN generic support"
-	depends on CAN_DEV && HAS_IOMEM
+	depends on HAS_IOMEM
 	---help---
 	  Support for CAN cards from Softing Gmbh & some cards
 	  from Vector Gmbh.
diff --git a/drivers/net/can/ti_hecc.c b/drivers/net/can/ti_hecc.c
index f898c6363729..f52a9755fb3e 100644
--- a/drivers/net/can/ti_hecc.c
+++ b/drivers/net/can/ti_hecc.c
@@ -50,6 +50,7 @@
 
 #include <linux/can/dev.h>
 #include <linux/can/error.h>
+#include <linux/can/led.h>
 #include <linux/can/platform/ti_hecc.h>
 
 #define DRV_NAME "ti_hecc"
@@ -593,6 +594,7 @@ static int ti_hecc_rx_pkt(struct ti_hecc_priv *priv, int mbxno)
 	spin_unlock_irqrestore(&priv->mbx_lock, flags);
 
 	stats->rx_bytes += cf->can_dlc;
+	can_led_event(priv->ndev, CAN_LED_EVENT_RX);
 	netif_receive_skb(skb);
 	stats->rx_packets++;
 
@@ -796,6 +798,7 @@ static irqreturn_t ti_hecc_interrupt(int irq, void *dev_id)
 			stats->tx_bytes += hecc_read_mbx(priv, mbxno,
 						HECC_CANMCF) & 0xF;
 			stats->tx_packets++;
+			can_led_event(ndev, CAN_LED_EVENT_TX);
 			can_get_echo_skb(ndev, mbxno);
 			--priv->tx_tail;
 		}
@@ -851,6 +854,8 @@ static int ti_hecc_open(struct net_device *ndev)
 		return err;
 	}
 
+	can_led_event(ndev, CAN_LED_EVENT_OPEN);
+
 	ti_hecc_start(ndev);
 	napi_enable(&priv->napi);
 	netif_start_queue(ndev);
@@ -869,6 +874,8 @@ static int ti_hecc_close(struct net_device *ndev)
 	close_candev(ndev);
 	ti_hecc_transceiver_switch(priv, 0);
 
+	can_led_event(ndev, CAN_LED_EVENT_STOP);
+
 	return 0;
 }
 
@@ -961,6 +968,9 @@ static int ti_hecc_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "register_candev() failed\n");
 		goto probe_exit_clk;
 	}
+
+	devm_can_led_init(ndev);
+
 	dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%u)\n",
 		priv->base, (u32) ndev->irq);
 
diff --git a/drivers/net/can/usb/Kconfig b/drivers/net/can/usb/Kconfig
index a4e4bee35710..fc96a3d83ebe 100644
--- a/drivers/net/can/usb/Kconfig
+++ b/drivers/net/can/usb/Kconfig
@@ -1,5 +1,5 @@
 menu "CAN USB interfaces"
-	depends on USB && CAN_DEV
+	depends on USB
 
 config CAN_EMS_USB
 	tristate "EMS CPC-USB/ARM7 CAN/USB interface"
@@ -48,4 +48,10 @@ config CAN_PEAK_USB
 	  This driver supports the PCAN-USB and PCAN-USB Pro adapters
 	  from PEAK-System Technik (http://www.peak-system.com).
 
+config CAN_8DEV_USB
+	tristate "8 devices USB2CAN interface"
+	---help---
+	  This driver supports the USB2CAN interface
+	  from 8 devices (http://www.8devices.com).
+
 endmenu
diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile
index 80a2ee41fd61..becef460a91a 100644
--- a/drivers/net/can/usb/Makefile
+++ b/drivers/net/can/usb/Makefile
@@ -6,5 +6,6 @@ obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o
 obj-$(CONFIG_CAN_ESD_USB2) += esd_usb2.o
 obj-$(CONFIG_CAN_KVASER_USB) += kvaser_usb.o
 obj-$(CONFIG_CAN_PEAK_USB) += peak_usb/
+obj-$(CONFIG_CAN_8DEV_USB) += usb_8dev.o