Merge tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new device support, features and cleanups for IIO in the 5.6 cycle

New device support

* ad7091r5 ADC
  - New driver with follow up patch adding scale and vref support.
  - DT bindings
* ad7923
  - Support for ad7908, ad7918 and ad7928 added to driver.
* bma180
  - Support the BMA254 accelerometer. Required fairly substantial rework
    to allow for small differences between this an existing parts.
* bma400 accelerometer
  - New driver with follow up patch for regulator support.
  - DT bindings.
* asc dlhl60d
  - New driver support this range of pressure and temperature sensors.
  - DT bindings.
* ltc2496 ADC
  - New driver to support this ADC.
  - Split the existing LTC2497 driver generic component out and reuse.
  - DT bindings.
* parallax ping
  - New driver supporting ultrasonic and laser tof distance sensors.
  - Bindings for these sensors.

New features

* core
  - New char type for read_raw returns, used for thermocouple types.
  - Rename read_first_n callback to read.   The reasons behind the original
    naming are lost to the mists of time.
* ad799x
  - Allow pm_ops to disable device completely allowing regulator power down.
* bma180
  - Enable basic regulator support.
* dmaengine buffer
  - Report platform data alignment requirements via new ABI.
* max31856
  - Add option to set mains filter rejection frequency and document
    new in_temp_filter_notch_center_frequency ABI.
  - Add support for configuring HW averaging (oversampling ratio)
  - Add runtime configuration of thermocouple type and document new ABI.
* maxim-thermocouple
  - Add read only access to thermocouple type using new ABI, includes
    adding more specific compatibles to reflect which variant of the
    chip is being used.
* mpu6050
  - Provide option to support the PMU9150 in package magnetometer directly
    rather than via auxiliary bus.
* stm32_adc
  - Add overrun interrupt checks to detect if this happens.
* st_lsm6dsx
  - Enable the sensor-hub support for lsm6dsm. Includes various reworks to
    allow this.

Cleanups and minor fixes

* Subsystem wide
  - Tidy up indentation in Kconfig and fix alphabetical order of AD7091R5.
  - Drop linux/gpio.h and linux/of_gpio.h from drivers that don't use them.
* ad7266
  - Convert to GPIO descriptors.
* ad7303
  - Avoid a dance with checking if the regulator is supplied by just
    using the optional request interface.
* ad7887
  - Simplify channel specification assignment to enable adding more devices.
* ad7923
  - Drop some unused and largely pointless defines of BOB_N==N variety.
  - Tidy up checkpatch warnings.
  - Add missing of_device_id table.
* adf4350
  - Convert to GPIO descriptors.
* ak8975
  - Convert to GPIO descriptors.
* ADIS library and drivers
  - Expand scope of txrx_lock to cover all state and rename as state_lock
  - Add unlocked read / write to allow grouping of consecutive calls under
    single lock / unlock.
  - Add unlocked check_status, reset to allow grouping under single
    lock / unlock.
  - Remove remaining uses of core mlock for local state protection.
    mlock should never be used directly as it protects tightly defined
    core IIO device management state.
* adis16240
  - Enforce only supported SPI mode on driver load + add DT binding doc.
* atlas-ph-sensor
  - Rename to atlas-sensor given it now covers things beyond ph sensors.
* bma180
  - Use local dev variable to tidy up code.
  - Use c99 style explicity .member assignment to make driver more readable.
* bmp280
  - Drop ACPI support. No evidence this was used and appropriate ID is not
    registered.
  - Allow ACPI to bind device via PRP0001
* dmaengine buffer
  - Use dma_request_chan instead of dma_request_slave_channel_reason as that
    ABI is going away.
  - Add module info to avoid tainting the kernel.
* hts221
  - Avoid magic number defines when only used to fill structure elements
    that are self describing.
* lm3533
  - Drop a stray semicolon.
* max9611
  - Cleanup enum handling to be more resilient to future changes.
* mpu6050
  - Delete MPU9150 from supported SPI devices as doesn't provide SPI.
  - Select I2C_MUX again after kbuild issue fixed elsewhere.
* stm32-timer
  - Drop an unnecessary register update.
* ssp_sensors
  - Convert to GPIO descriptors.
* st_sensors
  - drop !CONFIG_ACPI defines as ACPI_PTR() will stop them being used
    anyway.
  - Make default platform data structures __maybe_unsued.
  - Fill in some missing kernel-doc function parameters.
* st_lsm6dsx
  - white space fixes.
  - Mark some constants that aren't always used as __maybe_unused.
  - Drop of ID table guards as they just pervent use under ACPI.
  - Switch to device properties to allow ACPI usage.
* st_uvis25
  - Drop acpi.h include as no ACPI APIs used.
* ti-ads1015
  - Drop legacy platform data as no one seems to be using it.
  - Use the device property API instead of OF specific.
* ti-ads7950
  - typo fix in error message.

* tag 'iio-for-5.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (99 commits)
  iio: accel: bma180: BMA254 support
  iio: pressure: bmp280: Allow device to be enumerated from ACPI
  iio: pressure: bmp280: Drop ACPI support
  dt-bindings: iio: adc: convert sd modulator to json-schema
  iio: buffer: rename 'read_first_n' callback to 'read'
  iio: buffer-dmaengine: Report buffer length requirements
  bindings: iio: pressure: Add documentation for dlh driver
  dt-bindings: Add asc vendor
  iio: pressure: Add driver for DLH pressure sensors
  iio: buffer-dmaengine: Add module information
  iio: accel: bma180: Use explicit member assignment
  iio: accel: bma180: Basic regulator support
  iio: accel: bma180: Add dev helper variable
  iio: imu: st_lsm6dsx: enable sensor-hub support for lsm6dsm
  iio: imu: st_lsm6dsx: rename st_lsm6dsx_shub_read_reg in st_lsm6dsx_shub_read_output
  iio: imu: st_lsm6dsx: check if shub_output reg is located in primary page
  iio: imu: st_lsm6dsx: check if pull_up is located in primary page
  iio: imu: st_lsm6dsx: check if master_enable is located in primary page
  iio: imu: st_lsm6dsx: export max num of slave devices in st_lsm6dsx_shub_settings
  iio: light: remove unneeded semicolon
  ...

105 files changed, 4394 insertions, 860 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio
index faaa2166d741..d3e53a6d8331 100644
--- a/Documentation/ABI/testing/sysfs-bus-iio
+++ b/Documentation/ABI/testing/sysfs-bus-iio
@@ -1726,3 +1726,16 @@ Contact:	linux-iio@vger.kernel.org
 Description:
 		List of valid periods (in seconds) for which the light intensity
 		must be above the threshold level before interrupt is asserted.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_filter_notch_center_frequency
+KernelVersion:	5.5
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Center frequency in Hz for a notch filter. Used i.e. for line
+		noise suppression.
+
+What:		/sys/bus/iio/devices/iio:deviceX/in_temp_thermocouple_type
+KernelVersion:	5.5
+Contact:	linux-iio@vger.kernel.org
+Description:
+		One of the following thermocouple types: B, E, J, K, N, R, S, T.
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer b/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer
new file mode 100644
index 000000000000..d526e6571001
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-dma-buffer
@@ -0,0 +1,19 @@
+What:		/sys/bus/iio/devices/iio:deviceX/buffer/length_align_bytes
+KernelVersion:	5.4
+Contact:	linux-iio@vger.kernel.org
+Description:
+		DMA buffers tend to have a alignment requirement for the
+		buffers. If this alignment requirement is not met samples might
+		be dropped from the buffer.
+
+		This property reports the alignment requirements in bytes.
+		This means that the buffer size in bytes needs to be a integer
+		multiple of the number reported by this file.
+
+		The alignment requirements in number of sample sets will depend
+		on the enabled channels and the bytes per channel. This means
+		that the alignment requirement in samples sets might change
+		depending on which and how many channels are enabled. Whereas
+		the alignment requirement reported in bytes by this property
+		will remain static and does not depend on which channels are
+		enabled.
diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml
new file mode 100644
index 000000000000..4147f02b5e3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/accel/adi,adis16240.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/accel/adi,adis16240.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ADIS16240 Programmable Impact Sensor and Recorder driver
+
+maintainers:
+  - Alexandru Ardelean <alexandru.ardelean@analog.com>
+
+description: |
+  ADIS16240 Programmable Impact Sensor and Recorder driver that supports
+  SPI interface.
+    https://www.analog.com/en/products/adis16240.html
+
+properties:
+  compatible:
+    enum:
+      - adi,adis16240
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* Example for a SPI device node */
+        accelerometer@0 {
+            compatible = "adi,adis16240";
+            reg = <0>;
+            spi-max-frequency = <2500000>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/iio/accel/bma180.txt b/Documentation/devicetree/bindings/iio/accel/bma180.txt
index 3b25b4c4d446..f53237270b32 100644
--- a/Documentation/devicetree/bindings/iio/accel/bma180.txt
+++ b/