staging: remove mt7621-eth

driver/net/ethernet/mediatek/ now supports this hardware,
so we don't need a separate driver.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

16 files changed, 0 insertions, 4484 deletions

diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index c0901b96cfe4..62951e836cbc 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -114,8 +114,6 @@ source "drivers/staging/ralink-gdma/Kconfig"
 
 source "drivers/staging/mt7621-mmc/Kconfig"
 
-source "drivers/staging/mt7621-eth/Kconfig"
-
 source "drivers/staging/mt7621-dts/Kconfig"
 
 source "drivers/staging/gasket/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 57c6bce13ff4..d1b17ddcd354 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -47,7 +47,6 @@ obj-$(CONFIG_SPI_MT7621)	+= mt7621-spi/
 obj-$(CONFIG_SOC_MT7621)	+= mt7621-dma/
 obj-$(CONFIG_DMA_RALINK)	+= ralink-gdma/
 obj-$(CONFIG_MTK_MMC)		+= mt7621-mmc/
-obj-$(CONFIG_NET_MEDIATEK_SOC_STAGING)	+= mt7621-eth/
 obj-$(CONFIG_SOC_MT7621)	+= mt7621-dts/
 obj-$(CONFIG_STAGING_GASKET_FRAMEWORK)	+= gasket/
 obj-$(CONFIG_XIL_AXIS_FIFO)	+= axis-fifo/
diff --git a/drivers/staging/mt7621-eth/Documentation/devicetree/bindings/net/mediatek-net-gsw.txt b/drivers/staging/mt7621-eth/Documentation/devicetree/bindings/net/mediatek-net-gsw.txt
deleted file mode 100644
index 596b38552697..000000000000
--- a/drivers/staging/mt7621-eth/Documentation/devicetree/bindings/net/mediatek-net-gsw.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-Mediatek Gigabit Switch
-=======================
-
-The mediatek gigabit switch can be found on Mediatek SoCs.
-
-Required properties:
-- compatible: Should be "mediatek,mt7620-gsw", "mediatek,mt7621-gsw",
-  "mediatek,mt7623-gsw"
-- reg: Address and length of the register set for the device
-- interrupts: Should contain the gigabit switches interrupt
-
-
-Additional required properties for ARM based SoCs:
-- mediatek,reset-pin: phandle describing the reset GPIO
-- clocks: the clocks used by the switch
-- clock-names: the names of the clocks listed in the clocks property
-  these should be "trgpll", "esw", "gp2", "gp1"
-- mt7530-supply: the phandle of the regulator used to power the switch
-- mediatek,pctl-regmap: phandle to the port control regmap. this is used to
-  setup the drive current
-
-
-Optional properties:
-- interrupt-parent: Should be the phandle for the interrupt controller
-  that services interrupts for this device
-
-Example:
-
-gsw: switch@1b100000 {
-	compatible = "mediatek,mt7623-gsw";
-	reg = <0 0x1b110000 0 0x300000>;
-
-	interrupt-parent = <&pio>;
-	interrupts = <168 IRQ_TYPE_EDGE_RISING>;
-
-	clocks = <&apmixedsys CLK_APMIXED_TRGPLL>,
-		 <&ethsys CLK_ETHSYS_ESW>,
-		 <&ethsys CLK_ETHSYS_GP2>,
-		 <&ethsys CLK_ETHSYS_GP1>;
-	clock-names = "trgpll", "esw", "gp2", "gp1";
-
-	mt7530-supply = <&mt6323_vpa_reg>;
-
-	mediatek,pctl-regmap = <&syscfg_pctl_a>;
-	mediatek,reset-pin = <&pio 15 0>;
-
-	status = "okay";
-};
diff --git a/drivers/staging/mt7621-eth/Kconfig b/drivers/staging/mt7621-eth/Kconfig
deleted file mode 100644
index 44ea86c7a96c..000000000000
--- a/drivers/staging/mt7621-eth/Kconfig
+++ /dev/null
@@ -1,39 +0,0 @@
-config NET_VENDOR_MEDIATEK_STAGING
-	bool "MediaTek ethernet driver - staging version"
-	depends on RALINK
-	---help---
-	  If you have an MT7621 Mediatek SoC with ethernet, say Y.
-
-if NET_VENDOR_MEDIATEK_STAGING
-choice
-	prompt "MAC type"
-
-config NET_MEDIATEK_MT7621
-	bool "MT7621"
-	depends on MIPS && SOC_MT7621
-
-endchoice
-
-config NET_MEDIATEK_SOC_STAGING
-	tristate "MediaTek SoC Gigabit Ethernet support"
-	depends on NET_VENDOR_MEDIATEK_STAGING
-	select PHYLIB
-	---help---
-	  This driver supports the gigabit ethernet MACs in the
-	  MediaTek SoC family.
-
-config NET_MEDIATEK_MDIO
-	def_bool NET_MEDIATEK_SOC_STAGING
-	depends on NET_MEDIATEK_MT7621
-	select PHYLIB
-
-config NET_MEDIATEK_MDIO_MT7620
-	def_bool NET_MEDIATEK_SOC_STAGING
-	depends on NET_MEDIATEK_MT7621
-	select NET_MEDIATEK_MDIO
-
-config NET_MEDIATEK_GSW_MT7621
-	def_tristate NET_MEDIATEK_SOC_STAGING
-	depends on NET_MEDIATEK_MT7621
-
-endif #NET_VENDOR_MEDIATEK_STAGING
diff --git a/drivers/staging/mt7621-eth/Makefile b/drivers/staging/mt7621-eth/Makefile
deleted file mode 100644
index 018bcc3596b3..000000000000
--- a/drivers/staging/mt7621-eth/Makefile
+++ /dev/null
@@ -1,14 +0,0 @@
-#
-# Makefile for the Ralink SoCs built-in ethernet macs
-#
-
-mtk-eth-soc-y					+= mtk_eth_soc.o ethtool.o
-
-mtk-eth-soc-$(CONFIG_NET_MEDIATEK_MDIO)		+= mdio.o
-mtk-eth-soc-$(CONFIG_NET_MEDIATEK_MDIO_MT7620)	+= mdio_mt7620.o
-
-mtk-eth-soc-$(CONFIG_NET_MEDIATEK_MT7621)	+= soc_mt7621.o
-
-obj-$(CONFIG_NET_MEDIATEK_GSW_MT7621)		+= gsw_mt7621.o
-
-obj-$(CONFIG_NET_MEDIATEK_SOC_STAGING)		+= mtk-eth-soc.o
diff --git a/drivers/staging/mt7621-eth/TODO b/drivers/staging/mt7621-eth/TODO
deleted file mode 100644
index f9e47d4b4cd4..000000000000
--- a/drivers/staging/mt7621-eth/TODO
+++ /dev/null
@@ -1,13 +0,0 @@
-
-- verify devicetree documentation is consistent with code
-- fix ethtool - currently doesn't return valid data.
-- general code review and clean up
-- add support for second MAC on mt7621
-- convert gsw code to use switchdev interfaces
-- md7620_mmi_write etc should probably be wrapped
-  in a regmap abstraction.
-- Get soc_mt7621 to work with QDMA TX if possible.
-- Ensure phys are correctly configured when a cable
-  is plugged in.
-
-Cc: NeilBrown <neil@brown.name>
diff --git a/drivers/staging/mt7621-eth/ethtool.c b/drivers/staging/mt7621-eth/ethtool.c
deleted file mode 100644
index 8c4228e2c987..000000000000
--- a/drivers/staging/mt7621-eth/ethtool.c
+++ /dev/null
@@ -1,250 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*   This program is free software; you can redistribute it and/or modify
- *   it under the terms of the GNU General Public License as published by
- *   the Free Software Foundation; version 2 of the License
- *
- *   This program is distributed in the hope that it will be useful,
- *   but WITHOUT ANY WARRANTY; without even the implied warranty of
- *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *   GNU General Public License for more details.
- *
- *   Copyright (C) 2009-2016 John Crispin <blogic@openwrt.org>
- *   Copyright (C) 2009-2016 Felix Fietkau <nbd@openwrt.org>
- *   Copyright (C) 2013-2016 Michael Lee <igvtee@gmail.com>
- */
-
-#include "mtk_eth_soc.h"
-#include "ethtool.h"
-
-struct mtk_stat {
-	char name[ETH_GSTRING_LEN];
-	unsigned int idx;
-};
-
-#define MTK_HW_STAT(stat) { \
-	.name = #stat, \
-	.idx = offsetof(struct mtk_hw_stats, stat) / sizeof(u64) \
-}
-
-static const struct mtk_stat mtk_ethtool_hw_stats[] = {
-	MTK_HW_STAT(tx_bytes),
-	MTK_HW_STAT(tx_packets),
-	MTK_HW_STAT(tx_skip),
-	MTK_HW_STAT(tx_collisions),
-	MTK_HW_STAT(rx_bytes),
-	MTK_HW_STAT(rx_packets),
-	MTK_HW_STAT(rx_overflow),
-	MTK_HW_STAT(rx_fcs_errors),
-	MTK_HW_STAT(rx_short_errors),
-	MTK_HW_STAT(rx_long_errors),
-	MTK_HW_STAT(rx_checksum_errors),
-	MTK_HW_STAT(rx_flow_control_packets),
-};
-
-#define MTK_HW_STATS_LEN	ARRAY_SIZE(mtk_ethtool_hw_stats)
-
-static int mtk_get_link_ksettings(struct net_device *dev,
-				  struct ethtool_link_ksettings *cmd)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-	int err;
-
-	if (!mac->phy_dev)
-		return -ENODEV;
-
-	if (mac->phy_flags == MTK_PHY_FLAG_ATTACH) {
-		err = phy_read_status(mac->phy_dev);
-		if (err)
-			return -ENODEV;
-	}
-
-	phy_ethtool_ksettings_get(mac->phy_dev, cmd);
-	return 0;
-}
-
-static int mtk_set_link_ksettings(struct net_device *dev,
-				  const struct ethtool_link_ksettings *cmd)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	if (!mac->phy_dev)
-		return -ENODEV;
-
-	if (cmd->base.phy_address != mac->phy_dev->mdio.addr) {
-		if (mac->hw->phy->phy_node[cmd->base.phy_address]) {
-			mac->phy_dev = mac->hw->phy->phy[cmd->base.phy_address];
-			mac->phy_flags = MTK_PHY_FLAG_PORT;
-		} else if (mac->hw->mii_bus) {
-			mac->phy_dev = mdiobus_get_phy(mac->hw->mii_bus,
-						       cmd->base.phy_address);
-			if (!mac->phy_dev)
-				return -ENODEV;
-			mac->phy_flags = MTK_PHY_FLAG_ATTACH;
-		} else {
-			return -ENODEV;
-		}
-	}
-
-	return phy_ethtool_ksettings_set(mac->phy_dev, cmd);
-}
-
-static void mtk_get_drvinfo(struct net_device *dev,
-			    struct ethtool_drvinfo *info)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-	struct mtk_soc_data *soc = mac->hw->soc;
-
-	strlcpy(info->driver, mac->hw->dev->driver->name, sizeof(info->driver));
-	strlcpy(info->bus_info, dev_name(mac->hw->dev), sizeof(info->bus_info));
-
-	if (soc->reg_table[MTK_REG_MTK_COUNTER_BASE])
-		info->n_stats = MTK_HW_STATS_LEN;
-}
-
-static u32 mtk_get_msglevel(struct net_device *dev)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	return mac->hw->msg_enable;
-}
-
-static void mtk_set_msglevel(struct net_device *dev, u32 value)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	mac->hw->msg_enable = value;
-}
-
-static int mtk_nway_reset(struct net_device *dev)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	if (!mac->phy_dev)
-		return -EOPNOTSUPP;
-
-	return genphy_restart_aneg(mac->phy_dev);
-}
-
-static u32 mtk_get_link(struct net_device *dev)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-	int err;
-
-	if (!mac->phy_dev)
-		goto out_get_link;
-
-	if (mac->phy_flags == MTK_PHY_FLAG_ATTACH) {
-		err = genphy_update_link(mac->phy_dev);
-		if (err)
-			goto out_get_link;
-	}
-
-	return mac->phy_dev->link;
-
-out_get_link:
-	return ethtool_op_get_link(dev);
-}
-
-static int mtk_set_ringparam(struct net_device *dev,
-			     struct ethtool_ringparam *ring)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	if ((ring->tx_pending < 2) ||
-	    (ring->rx_pending < 2) ||
-	    (ring->rx_pending > mac->hw->soc->dma_ring_size) ||
-	    (ring->tx_pending > mac->hw->soc->dma_ring_size))
-		return -EINVAL;
-
-	dev->netdev_ops->ndo_stop(dev);
-
-	mac->hw->tx_ring.tx_ring_size = BIT(fls(ring->tx_pending) - 1);
-	mac->hw->rx_ring[0].rx_ring_size = BIT(fls(ring->rx_pending) - 1);
-
-	return dev->netdev_ops->ndo_open(dev);
-}
-
-static void mtk_get_ringparam(struct net_device *dev,
-			      struct ethtool_ringparam *ring)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-
-	ring->rx_max_pending = mac->hw->soc->dma_ring_size;
-	ring->tx_max_pending = mac->hw->soc->dma_ring_size;
-	ring->rx_pending = mac->hw->rx_ring[0].rx_ring_size;
-	ring->tx_pending = mac->hw->tx_ring.tx_ring_size;
-}
-
-static void mtk_get_strings(struct net_device *dev, u32 stringset, u8 *data)
-{
-	int i;
-
-	switch (stringset) {
-	case ETH_SS_STATS:
-		for (i = 0; i < MTK_HW_STATS_LEN; i++) {
-			memcpy(data, mtk_ethtool_hw_stats[i].name,
-			       ETH_GSTRING_LEN);
-			data += ETH_GSTRING_LEN;
-		}
-		break;
-	}
-}
-
-static int mtk_get_sset_count(struct net_device *dev, int sset)
-{
-	switch (sset) {
-	case ETH_SS_STATS:
-		return MTK_HW_STATS_LEN;
-	default:
-		return -EOPNOTSUPP;
-	}
-}
-
-static void mtk_get_ethtool_stats(struct net_device *dev,
-				  struct ethtool_stats *stats, u64 *data)
-{
-	struct mtk_mac *mac = netdev_priv(dev);
-	struct mtk_hw_stats *hwstats = mac->hw_stats;
-	unsigned int start;
-	int i;
-
-	if (netif_running(dev) && netif_device_present(dev)) {
-		if (spin_trylock(&hwstats->stats_lock)) {
-			mtk_stats_update_mac(mac);
-			spin_unlock(&hwstats->stats_lock);
-		}
-	}
-
-	do {
-		start = u64_stats_fetch_begin_irq(&hwstats->syncp);
-		for (i = 0; i < MTK_HW_STATS_LEN; i++)
-			data[i] = ((u64 *)hwstats)[mtk_ethtool_hw_stats[i].idx];
-
-	} while (u64_stats_fetch_retry_irq(&hwstats->syncp, start));
-}
-
-static struct ethtool_ops mtk_ethtool_ops = {
-	.get_link_ksettings     = mtk_get_link_ksettings,
-	.set_link_ksettings     = mtk_set_link_ksettings,
-	.get_drvinfo		= mtk_get_drvinfo,
-	.get_msglevel		= mtk_get_msglevel,
-	.set_msglevel		= mtk_set_msglevel,
-	.nway_reset		= mtk_nway_reset,
-	.get_link		= mtk_get_link,
-	.set_ringparam		= mtk_set_ringparam,
-	.get_ringparam		= mtk_get_ringparam,
-};
-
-void mtk_set_ethtool_ops(struct net_device *netdev)
-{
-	struct mtk_mac *mac = netdev_priv(netdev);
-	struct mtk_soc_data *soc = mac->hw->soc;
-
-	if (soc->reg_table[MTK_REG_MTK_COUNTER_BASE]) {
-		mtk_ethtool_ops.get_strings = mtk_get_strings;
-		mtk_ethtool_ops.get_sset_count = mtk_get_sset_count;
-		mtk_ethtool_ops.get_ethtool_stats = mtk_get_ethtool_stats;
-	}
-
-	netdev->ethtool_ops = &mtk_ethtool_ops;
-}
diff --git a/drivers/staging/mt7621-eth/ethtool.h b/drivers/staging/mt7621-eth/ethtool.h
deleted file mode 100644
index 0071469aea6c..000000000000
--- a/drivers/staging/mt7621-eth/ethtool.h
+++ /dev/null
@@ -1,15 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- *   Copyright (C) 2009-2016 John Crispin <blogic@openwrt.org>
- *   Copyright (C) 2009-2016 Felix Fietkau <nbd@openwrt.org>
- *   Copyright (C) 2013-2016 Michael Lee <igvtee@gmail.com>
- */
-
-#ifndef MTK_ETHTOOL_H
-#define MTK_ETHTOOL_H
-
-#include <linux/ethtool.h>
-
-void mtk_set_ethtool_ops(struct net_device *netdev);
-
-#endif /* MTK_ETHTOOL_H */
diff --git a/drivers/staging/mt7621-eth/gsw_mt7620.h b/drivers/staging/mt7621-eth/gsw_mt7620.h
deleted file mode 100644
index 70f7e5481952..000000000000
--- a/drivers/staging/mt7621-eth/gsw_mt7620.h
+++ /dev/null
@@ -1,277 +0,0 @@
-/*   This program is free software; you can redistribute it and/or modify
- *   it under the terms of the GNU General Public License as published by
- *   the Free Software Foundation; version 2 of the License
- *
- *   This program is distributed in the hope that it will be useful,
- *   but WITHOUT ANY WARRANTY; without even the implied warranty of
- *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *   GNU General Public License for more details.
- *
- *   Copyright (C) 2009-2016 John Crispin <blogic@openwrt.org>
- *   Copyright (C) 2009-2016 Felix Fietkau <nbd@openwrt.org>
- *   Copyright (C) 2013-2016 Michael Lee <igvtee@gmail.com>
- */
-
-#ifndef _RALINK_GSW_MT7620_H__
-#define _RALINK_GSW_MT7620_H__
-
-#define GSW_REG_PHY_TIMEOUT	(5 * HZ)
-
-#define MT7620_GSW_REG_PIAC	0x0004
-
-#define GSW_NUM_VLANS		16
-#define GSW_NUM_VIDS		4096
-#define GSW_NUM_PORTS		7
-#define GSW_PORT6		6
-
-#define GSW_MDIO_ACCESS		BIT(31)
-#define GSW_MDIO_READ		BIT(19)
-#define GSW_MDIO_WRITE		BIT(18)
-#define GSW_MDIO_START		BIT(16)
-#define GSW_MDIO_ADDR_SHIFT	20
-#define GSW_MDIO_REG_SHIFT	25
-
-#define GSW_REG_PORT_PMCR(x)	(0x3000 + (x * 0x100))
-#define GSW_REG_PORT_STATUS(x)	(0x3008 + (x * 0x100))
-#define GSW_REG_SMACCR0		0x3fE4
-#define GSW_REG_SMACCR1		0x3fE8
-#define GSW_REG_CKGCR		0x3ff0
-
-#define GSW_REG_IMR		0x7008
-#define GSW_REG_ISR		0x700c
-#define GSW_REG_GPC1		0x7014
-
-#define SYSC_REG_CHIP_REV_ID	0x0c
-#define SYSC_REG_CFG		0x10
-#define SYSC_REG_CFG1		0x14
-#define RST_CTRL_MCM		BIT(2)
-#define SYSC_PAD_RGMII2_MDIO	0x58
-#define SYSC_GPIO_MODE		0x60
-
-#define PORT_IRQ_ST_CHG		0x7f
-
-#define MT7621_ESW_PHY_POLLING	0x0000
-#define MT7620_ESW_PHY_POLLING	0x7000
-
-#define	PMCR_IPG		BIT(18)
-#define	PMCR_MAC_MODE		BIT(16)
-#define	PMCR_FORCE		BIT(15)
-#define	PMCR_TX_EN		BIT(14)
-#define	PMCR_RX_EN		BIT(13)
-#define	PMCR_BACKOFF		BIT(9)
-#define	PMCR_BACKPRES		BIT(8)
-#define	PMCR_RX_FC		BIT(5)
-#define	PMCR_TX_FC		BIT(4)
-#define	PMCR_SPEED(_x)		(_x << 2)
-#define	PMCR_DUPLEX		BIT(1)
-#define	PMCR_LINK		BIT(0)
-
-#define PHY_AN_EN		BIT(31)
-#define PHY_PRE_EN		BIT(30)
-#define PMY_MDC_CONF(_x)	((_x & 0x3f) << 24)
-
-/* ethernet subsystem config register */
-#define ETHSYS_SYSCFG0		0x14
-/* ethernet subsystem clock register */
-#define ETHSYS_CLKCFG0		0x2c
-#define ETHSYS_TRGMII_CLK_SEL362_5	BIT(11)
-
-/* p5 RGMII wrapper TX clock control register */
-#define MT7530_P5RGMIITXCR	0x7b04
-/* p5 RGMII wrapper RX clock control register */
-#define MT7530_P5RGMIIRXCR	0x7b00
-/* TRGMII TDX ODT registers */
-#define MT7530_TRGMII_TD0_ODT	0x7a54
-#define MT7530_TRGMII_TD1_ODT	0x7a5c
-#define MT7530_TRGMII_TD2_ODT	0x7a64
-#define MT7530_TRGMII_TD3_ODT	0x7a6c
-#define MT7530_TRGMII_TD4_ODT	0x7a74
-#define MT7530_TRGMII_TD5_ODT	0x7a7c
-/* TRGMII TCK ctrl register */
-#define MT7530_TRGMII_TCK_CTRL	0x7a78
-/* TRGMII Tx ctrl register */
-#define MT7530_TRGMII_TXCTRL	0x7a40
-/* port 6 extended control register */
-#define MT7530_P6ECR            0x7830
-/* IO driver control register */
-#define MT7530_IO_DRV_CR	0x7810
-/* top signal control register */
-#define MT7530_TOP_SIG_CTRL	0x7808
-/* modified hwtrap register */
-#define MT7530_MHWTRAP		0x7804
-/* hwtrap status register */
-#define MT7530_HWTRAP		0x7800
-/* status interrupt register */
-#define MT7530_SYS_INT_STS	0x700c
-/* system nterrupt register */
-#define MT7530_SYS_INT_EN	0x7008
-/* system control register */
-#define MT7530_SYS_CTRL		0x7000
-/* port MAC status register */
-#define MT7530_PMSR_P(x)	(0x3008 + (x * 0x100))
-/* port MAC control register */
-#define MT7530_PMCR_P(x)	(0x3000 + (x * 0x100))
-
-#define MT7621_XTAL_SHIFT	6
-#define MT7621_XTAL_MASK	0x7
-#define MT7621_XTAL_25		6
-#define MT7621_XTAL_40		3
-#define MT7621_MDIO_DRV_MASK	(3 << 4)
-#define MT7621_GE1_MODE_MASK	(3 << 12)
-
-#define TRGMII_TXCTRL_TXC_INV	BIT(30)
-#define P6ECR_INTF_MODE_RGMII	BIT(1)
-#define P5RGMIIRXCR_C_ALIGN	BIT(8)
-#define P5RGMIIRXCR_DELAY_2	BIT(1)
-#define P5RGMIITXCR_DELAY_2	(BIT(8) | BIT(2))
-
-/* TOP_SIG_CTRL bits */
-#define TOP_SIG_CTRL_NORMAL	(BIT(17) | BIT(16))
-
-/* MHWTRAP bits */
-#define MHWTRAP_MANUAL		BIT(16)
-#define MHWTRAP_P5_MAC_SEL	BIT(13)
-#define MHWTRAP_P6_DIS		BIT(8)
-#define MHWTRAP_P5_RGMII_MODE	BIT(7)
-#define MHWTRAP_P5_DIS		BIT(6)
-#define MHWTRAP_PHY_ACCESS	BIT(5)
-
-/* HWTRAP bits */
-#define HWTRAP_XTAL_SHIFT	9
-#define HWTRAP_XTAL_MASK	0x3
-
-/* SYS_CTRL bits */
-#define SYS_CTRL_SW_RST		BIT(1)
-#define SYS_CTRL_REG_RST	BIT(0)
-
-/* PMCR bits */
-#define PMCR_IFG_XMIT_96	BIT(18)
-#define PMCR_MAC_MODE		BIT(16)
-#define PMCR_FORCE_MODE		BIT(15)
-#define PMCR_TX_EN		BIT(14)
-#define PMCR_RX_EN		BIT(13)
-#define PMCR_BACK_PRES_EN	BIT(9)
-#define PMCR_BACKOFF_EN		BIT(8)
-#define PMCR_TX_FC_EN		BIT(5)
-#define PMCR_RX_FC_EN		BIT(4)
-#define PMCR_FORCE_SPEED_1000	BIT(3)
-#define PMCR_FORCE_FDX		BIT(1)
-#define PMCR_FORCE_LNK		BIT(0)
-#define PMCR_FIXED_LINK		(PMCR_IFG_XMIT_96 | PMCR_MAC_MODE | \
-				 PMCR_FORCE_MODE | PMCR_TX_EN | PMCR_RX_EN | \
-				 PMCR_BACK_PRES_EN | PMCR_BACKOFF_EN | \
-				 PMCR_FORCE_SPEED_1000 | PMCR_FORCE_FDX | \
-				 PMCR_FORCE_LNK)
-
-#define PMCR_FIXED_LINK_FC	(PMCR_FIXED_LINK | \
-				 PMCR_TX_FC_EN | PMCR_RX_FC_EN)
-
-/* TRGMII control registers */
-#define GSW_INTF_MODE		0x390
-#define GSW_TRGMII_TD0_ODT	0x354
-#define GSW_TRGMII_TD1_ODT	0x35c
-#define GSW_TRGMII_TD2_ODT	0x364
-#define GSW_TRGMII_TD3_ODT	0x36c
-#define GSW_TRGMII_TXCTL_ODT	0x374
-#define GSW_TRGMII_TCK_ODT	0x37c
-#define GSW_TRGMII_RCK_CTRL	0x300
-
-#define INTF_MODE_TRGMII	BIT(1)
-#define TRGMII_RCK_CTRL_RX_RST	BIT(31)
-
-/* Mac control registers */
-#define MTK_MAC_P2_MCR		0x200
-#define MTK_MAC_P1_MCR		0x100
-
-#define MAC_MCR_MAX_RX_2K	BIT(29)
-#define MAC_MCR_IPG_CFG		(BIT(18) | BIT(16))
-#define MAC_MCR_FORCE_MODE	BIT(15)
-#define MAC_MCR_TX_EN		BIT(14)
-#define MAC_MCR_RX_EN		BIT(13)
-#define MAC_MCR_BACKOFF_EN	BIT(9)
-#define MAC_MCR_BACKPR_EN	BIT(8)
-#define MAC_MCR_FORCE_RX_FC	BIT(5)
-#define MAC_MCR_FORCE_TX_FC	BIT(4)
-#define MAC_MCR_SPEED_1000	BIT(3)
-#define MAC_MCR_FORCE_DPX	BIT(1)
-#define MAC_MCR_FORCE_LINK	BIT(0)
-#define MAC_MCR_FIXED_LINK	(MAC_MCR_MAX_RX_2K | MAC_MCR_IPG_CFG | \
-				 MAC_MCR_FORCE_MODE | MAC_MCR_TX_EN | \
-				 MAC_MCR_RX_EN | MAC_MCR_BACKOFF_EN | \
-				 MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_RX_FC | \
-				 MAC_MCR_FORCE_TX_FC | MAC_MCR_SPEED_1000 | \
-				 MAC_MCR_FORCE_DPX | MAC_MCR_FORCE_LINK)
-#define MAC_MCR_FIXED_LINK_FC	(MAC_MCR_MAX_RX_2K | MAC_MCR_IPG_CFG | \
-				 MAC_MCR_FIXED_LINK)
-
-/* possible XTAL speed */
-#define	MT7623_XTAL_40		0
-#define MT7623_XTAL_20		1
-#define MT7623_XTAL_25		3
-
-/* GPIO port control registers */
-#define	GPIO_OD33_CTRL8		0x4c0
-#define	GPIO_BIAS_CTRL		0xed0
-#define GPIO_DRV_SEL10		0xf00
-
-/* on MT7620 the functio of port 4 can be software configured */
-enum {
-	PORT4_EPHY = 0,
-	PORT4_EXT,
-};
-
-/* struct mt7620_gsw -	the structure that holds the SoC specific data
- * @dev:		The Device struct
- * @base:		The base address
- * @piac_offset:	The PIAC base may change depending on SoC
- * @irq:		The IRQ we are using
- * @port4:		The port4 mode on MT7620
- * @autopoll:		Is MDIO autopolling enabled
- * @ethsys:		The ethsys register map
- * @pctl:		The pin control register map
- * @clk_gsw:		The switch clock
- * @clk_gp1:		The gmac1 clock
- * @clk_gp2:		The gmac2 clock
- * @clk_trgpll:		The trgmii pll clock
- */
-struct mt7620_gsw {
-	struct device		*dev;
-	void __iomem		*base;
-	u32			piac_offset;
-	int			irq;
-	int			port4;
-	unsigned long int	autopoll;
-
-	struct regmap		*ethsys;
-	struct regmap		*pctl;
-
-	struct clk		*clk_gsw;
-	struct clk		*clk_gp1;
-	struct clk		*clk_gp2;
-	struct clk		*clk_trgpll;
-};
-
-/* switch register I/O wrappers */
-void mtk_switch_w32(struct mt7620_gsw *gsw, u32 val, unsigned int reg);
-u32 mtk_switch_r32(struct mt7620_gsw *gsw, unsigned int reg);
-
-/* the callback used by the driver core to bringup the switch */
-int mtk_gsw_init(struct mtk_eth *eth);
-
-/* MDIO access wrappers */
-int mt7620_mdio_write(struct mii_bus *bus, int phy_addr, int phy_reg, u16 val);
-int mt7620_mdio_read(struct mii_bus *bus, int phy_addr, int phy_reg);
-void mt7620_mdio_link_adjust(struct mtk_eth *eth, int port);
-int mt7620_has_carrier(struct mtk_eth *eth);
-void mt7620_print_link_state(struct mtk_eth *eth, int port, int link,
-			     int speed, int duplex);
-void mt7530_mdio_w32(struct mt7620_gsw *gsw, u32 reg, u32 val);
-u32 mt7530_mdio_r32(struct mt7620_gsw *gsw, u32 reg);
-void mt7530_mdio_m32(struct mt7620_gsw *gsw, u32 mask, u32 set, u32 reg);
-
-u32 _mt7620_mii_write(struct mt7620_gsw *gsw, u32 phy_addr,
-		      u32 phy_register, u32 write_data);
-u32 _mt7620_mii_read(struct mt7620_gsw *gsw, int phy_addr, int phy_reg);
-void mt7620_handle_carrier(struct mtk_eth *eth);
-
-#endif
diff --git a/drivers/staging/mt7621-eth/gsw_mt7621.c b/drivers/staging/mt7621-eth/gsw_mt7621.c
deleted file mode 100644
index 53767b17bad9..000000000000
--- a/drivers/staging/mt7621-eth/gsw_mt7621.c
+++ /dev/null
@@ -1,297 +0,0 @@
-/*   This program is free software; you can redistribute it and/or modify
- *   it under the terms of the GNU General Public License as published by
- *   the Free Software Foundation; version 2 of the License
- *
- *   This program is distributed in the hope that it will be useful,
- *   but WITHOUT ANY WARRANTY; without even the implied warranty of
- *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *   GNU General Public License for more details.
- *
- *   Copyright (C) 2009-2016 John Crispin <blogic@openwrt.org>
- *   Copyright (C) 2009-2016 Felix Fietkau <nbd@openwrt.org>
- *   Copyright (C) 2013-2016 Michael Lee <igvtee@gmail.com>
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/platform_device.h>
-#include <linux/of_device.h>
-#include <linux/of_irq.h>
-
-#include <ralink_regs.h>
-
-#include "mtk_eth_soc.h"
-#include "gsw_mt7620.h"
-
-void mtk_switch_w32(struct mt7620_gsw *gsw, u32 val, unsigned int reg)
-{
-	iowrite32(val, gsw->base + reg);
-}
-EXPORT_SYMBOL_GPL(mtk_switch_w32);
-
-u32 mtk_switch_r32(struct mt7620_gsw *gsw, unsigned int reg)
-{
-	return ioread32(gsw->base + reg);
-}
-EXPORT_SYMBOL_GPL(mtk_switch_r32);
-
-static irqreturn_t gsw_interrupt_mt7621(int irq, void *_eth)
-{
-	struct mtk_eth *eth = (struct mtk_eth *)_eth;
-	struct mt7620_gsw *gsw = (struct mt7620_gsw *)eth->sw_priv;
-	u32 reg, i;
-
-	reg = mt7530_mdio_r32(gsw, MT7530_SYS_INT_STS);
-
-	for (i = 0; i < 5; i++) {
-		unsigned int link;
-
-		if ((reg & BIT(i)) == 0)
-			continue;
-
-		link = mt7530_mdio_r32(gsw, MT7530_PMSR_P(i)) & 0x1;
-
-		if (link == eth->link[i])
-			continue;
-
-		eth->link[i] = link;
-		if (link)
-			netdev_info(*eth->netdev,
-				    "port %d link up\n", i);
-		else
-			netdev_info(*eth->netdev,
-				    "port %d link down\n", i);
-	}
-
-	mt7530_mdio_w32(gsw, MT7530_SYS_INT_STS, 0x1f);
-
-	return IRQ_HANDLED;
-}
-
-static void mt7621_hw_init(struct mtk_eth *eth, struct mt7620_gsw *gsw,
-			   struct device_node *np)
-{
-	u32 i;
-	u32 val;
-
-	/* hardware reset the switch */
-	mtk_reset(eth, RST_CTRL_MCM);
-	mdelay(10);
-
-	/* reduce RGMII2 PAD driving strength */
-	rt_sysc_m32(MT7621_MDIO_DRV_MASK, 0, SYSC_PAD_RGMII2_MDIO);
-
-	/* gpio mux - RGMII1=Normal mode */
-	rt_sysc_m32(BIT(14), 0, SYSC_GPIO_MODE);
-
-	/* set GMAC1 RGMII mode */
-	rt_sysc_m32(MT7621_GE1_MODE_MASK, 0, SYSC_REG_CFG1);
-
-	/* enable MDIO to control MT7530 */
-	rt_sysc_m32(3 << 12, 0, SYSC_GPIO_MODE);
-
-	/* turn off all PHYs */
-	for (i = 0; i <= 4; i++) {
-		val = _mt7620_mii_read(gsw, i, 0x0);
-		val |= BIT(11);
-		_mt7620_mii_write(gsw, i, 0x0, val);
-	}
-
-	/* reset the switch */
-	mt7530_mdio_w32(gsw, MT7530_SYS_CTRL,
-			SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
-	usleep_range(10, 20);
-
-	if ((rt_sysc_r32(SYSC_REG_CHIP_REV_ID) & 0xFFFF) == 0x0101) {
-		/* GE1, Force 1000M/FD, FC ON, MAX_RX_LENGTH 1536 */
-		mtk_switch_w32(gsw, MAC_MCR_FIXED_LINK, MTK_MAC_P2_MCR);
-		mt7530_mdio_w32(gsw, MT7530_PMCR_P(6), PMCR_FIXED_LINK);
-	} else {
-		/* GE1, Force 1000M/FD, FC ON, MAX_RX_LENGTH 1536 */
-		mtk_switch_w32(gsw, MAC_MCR_FIXED_LINK_FC, MTK_MAC_P1_MCR);
-		mt7530_mdio_w32(gsw, MT7530_PMCR_P(6), PMCR_FIXED_LINK_FC);
-	}
-
-	/* GE2, Link down */
-	mtk_switch_w32(gsw, MAC_MCR_FORCE_MODE, MTK_MAC_P2_MCR);
-
-	/* Enable Port 6, P5 as GMAC5, P5 disable */
-	val = mt7530_mdio_r32(gsw, MT7530_MHWTRAP);
-	/* Enable Port 6 */
-	val &= ~MHWTRAP_P6_DIS;
-	/* Disable Port 5 */
-	val |= MHWTRAP_P5_DIS;
-	/* manual override of HW-Trap */
-	val |= MHWTRAP_MANUAL;
-	mt7530_mdio_w32(gsw, MT7530_MHWTRAP, val);
-
-	val = rt_sysc_r32(SYSC_REG_CFG);
-	val = (val >> MT7621_XTAL_SHIFT) & MT7621_XTAL_MASK;
-	if (val < MT7621_XTAL_25 && val >= MT7621_XTAL_40) {
-		/* 40Mhz */
-
-		/* disable MT7530 core clock */
-		_mt7620_mii_write(gsw, 0, 13, 0x1f);
-		_mt7620_mii_write(gsw, 0, 14, 0x410);
-		_mt7620_mii_write(gsw, 0, 13, 0x401f);
-		_mt7620_mii_write(gsw, 0, 14, 0x0);
-
-		/* disable MT7530 PLL */
-		_mt7620_mii_write(gsw, 0, 13, 0x1f);
-		_mt7620_mii_write(gsw, 0, 14, 0x40d);
-		_mt7620_mii_write(gsw, 0, 13, 0x401f);
-		_mt7620_mii_write(gsw, 0, 14, 0x2020);
-
-		/* for MT7530 core clock = 500Mhz */
-		_mt7620_mii_write(gsw, 0, 13, 0x1f);
-		_mt7620_mii_write(gsw, 0, 14, 0x40e);
-		_mt7620_mii_write(gsw, 0, 13, 0x401f);
-		_mt7620_mii_write(gsw, 0, 14, 0x119);
-
-		/* enable MT7530 PLL */
-		_mt7620_mii_write(gsw, 0, 13, 0x1f);
-		_mt7620_mii_write(gsw, 0, 14, 0x40d);
-		_mt7620_mii_write(gsw, 0, 13, 0x401f);
-		_mt7620_mii_write(gsw, 0, 14, 0x2820);
-
-		usleep_range(20, 40);
-
-		/* enable MT7530 core clock */
-		_mt7620_mii_write(gsw, 0, 13, 0x1f);
-		_mt7620_mii_write(gsw, 0, 14, 0x410);
-		_mt7620_mii_write(gsw, 0, 13, 0x401f);
-	}
-
-	/* RGMII */
-	_mt7620_mii_write(gsw, 0, 14, 0x1);
-
-	/* set MT7530 central align */
-	mt7530_mdio_m32(gsw, BIT(0), P6ECR_INTF_MODE_RGMII, MT7530_P6ECR);
-	mt7530_mdio_m32(gsw, TRGMII_TXCTRL_TXC_INV, 0,
-			MT7530_TRGMII_TXCTRL);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TCK_CTRL, 0x855);
-
-	/* delay setting for 10/1000M */
-	mt7530_mdio_w32(gsw, MT7530_P5RGMIIRXCR,
-			P5RGMIIRXCR_C_ALIGN | P5RGMIIRXCR_DELAY_2);
-	mt7530_mdio_w32(gsw, MT7530_P5RGMIITXCR, 0x14);
-
-	/* lower Tx Driving*/
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD0_ODT, 0x44);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD1_ODT, 0x44);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD2_ODT, 0x44);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD3_ODT, 0x44);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD4_ODT, 0x44);
-	mt7530_mdio_w32(gsw, MT7530_TRGMII_TD5_ODT, 0x44);
-
-	/* turn on all PHYs */
-	for (i = 0; i <= 4; i++) {
-		val = _mt7620_mii_read(gsw, i, 0);
-		val &= ~BIT(11);
-		_mt7620_mii_write(gsw, i, 0, val);
-	}
-
-#define MT7530_NUM_PORTS 8
-#define REG_ESW_PORT_PCR(x)    (0x2004 | ((x) << 8))
-#define REG_ESW_PORT_PVC(x)    (0x2010 | ((x) << 8))
-#define REG_ESW_PORT_PPBV1(x)  (0x2014 | ((x) << 8))
-#define MT7530_CPU_PORT                6
-
-	/* This is copied from mt7530_apply_config in libreCMC driver */
-	{
-		int i;
-
-		for (i = 0; i < MT7530_NUM_PORTS; i++)
-			mt7530_mdio_w32(gsw, REG_ESW_PORT_PCR(i), 0x00400000);
-
-		mt7530_mdio_w32(gsw, REG_ESW_PORT_PCR(MT7530_CPU_PORT),
-				0x00ff0000);
-
-		for (i = 0; i < MT7530_NUM_PORTS; i++)
-			mt7530_mdio_w32(gsw, REG_ESW_PORT_PVC(i), 0x810000c0);
-	}
-
-	/* enable irq */
-	mt7530_mdio_m32(gsw, 0, 3 << 16, MT7530_TOP_SIG_CTRL);
-	mt7530_mdio_w32(gsw, MT7530_SYS_INT_EN, 0x1f);
-}
-
-static const struct of_device_id mediatek_gsw_match[] = {
-	{ .compatible = "mediatek,mt7621-gsw" },
-	{},
-};
-MODULE_DEVICE_TABLE(of, mediatek_gsw_match);
-
-int mtk_gsw_init(struct mtk_eth *eth)
-{
-	struct device_node *np = eth->switch_np;
-	struct platform_device *pdev =