Merge tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging driver updates from Greg KH:
 "Here is the big staging driver pull request for 4.6-rc1.

  Lots of little things here, over 1600 patches or so.  Notable is all
  of the good Lustre work happening, those developers have finally woken
  up and are cleaning up their code greatly.  The Outreachy intern
  application process is also happening, which brought in another 400 or
  so patches.  Full details are in the very long shortlog.

  All of these have been in linux-next with no reported issues"

* tag 'staging-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1673 commits)
  staging: lustre: fix aligments in lnet selftest
  staging: lustre: report minimum of two buffers for LNet selftest load test
  staging: lustre: test for proper errno code in lstcon_rpc_trans_abort
  staging: lustre: filter remaining extra spacing for lnet selftest
  staging: lustre: remove extra spacing when setting variable for lnet selftest
  staging: lustre: remove extra spacing of variable declartions for lnet selftest
  staging: lustre: fix spacing issues checkpatch reported in lnet selftest
  staging: lustre: remove returns in void function for lnet selftest
  staging: lustre: fix bogus lst errors for lnet selftest
  staging: netlogic: Replacing pr_err with dev_err after the call to devm_kzalloc
  staging: mt29f_spinand: Replacing pr_info with dev_info after the call to devm_kzalloc
  staging: android: ion: fix up file mode
  staging: ion: debugfs invalid gfp mask
  staging: rts5208: Replace pci_enable_device with pcim_enable_device
  Staging: ieee80211: Place constant on right side of the test.
  staging: speakup: Replace del_timer with del_timer_sync
  staging: lowmemorykiller: fix 2 checks that checkpatch complained
  staging: mt29f_spinand: Drop void pointer cast
  staging: rdma: hfi1: file_ops: Replace ALIGN with PAGE_ALIGN
  staging: rdma: hfi1: driver: Replace IS_ALIGNED with PAGE_ALIGNED
  ...

1 files changed, 2438 insertions, 0 deletions

diff --git a/drivers/misc/panel.c b/drivers/misc/panel.c
new file mode 100644
index 000000000000..6030ac5b8c63
--- /dev/null
+++ b/drivers/misc/panel.c
@@ -0,0 +1,2438 @@
+/*
+ * Front panel driver for Linux
+ * Copyright (C) 2000-2008, Willy Tarreau <w@1wt.eu>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * This code drives an LCD module (/dev/lcd), and a keypad (/dev/keypad)
+ * connected to a parallel printer port.
+ *
+ * The LCD module may either be an HD44780-like 8-bit parallel LCD, or a 1-bit
+ * serial module compatible with Samsung's KS0074. The pins may be connected in
+ * any combination, everything is programmable.
+ *
+ * The keypad consists in a matrix of push buttons connecting input pins to
+ * data output pins or to the ground. The combinations have to be hard-coded
+ * in the driver, though several profiles exist and adding new ones is easy.
+ *
+ * Several profiles are provided for commonly found LCD+keypad modules on the
+ * market, such as those found in Nexcom's appliances.
+ *
+ * FIXME:
+ *      - the initialization/deinitialization process is very dirty and should
+ *        be rewritten. It may even be buggy.
+ *
+ * TODO:
+ *	- document 24 keys keyboard (3 rows of 8 cols, 32 diodes + 2 inputs)
+ *      - make the LCD a part of a virtual screen of Vx*Vy
+ *	- make the inputs list smp-safe
+ *      - change the keyboard to a double mapping : signals -> key_id -> values
+ *        so that applications can change values without knowing signals
+ *
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/miscdevice.h>
+#include <linux/slab.h>
+#include <linux/ioport.h>
+#include <linux/fcntl.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/ctype.h>
+#include <linux/parport.h>
+#include <linux/list.h>
+#include <linux/notifier.h>
+#include <linux/reboot.h>
+#include <generated/utsrelease.h>
+
+#include <linux/io.h>
+#include <linux/uaccess.h>
+
+#define LCD_MINOR		156
+#define KEYPAD_MINOR		185
+
+#define PANEL_VERSION		"0.9.5"
+
+#define LCD_MAXBYTES		256	/* max burst write */
+
+#define KEYPAD_BUFFER		64
+
+/* poll the keyboard this every second */
+#define INPUT_POLL_TIME		(HZ / 50)
+/* a key starts to repeat after this times INPUT_POLL_TIME */
+#define KEYPAD_REP_START	(10)
+/* a key repeats this times INPUT_POLL_TIME */
+#define KEYPAD_REP_DELAY	(2)
+
+/* keep the light on this times INPUT_POLL_TIME for each flash */
+#define FLASH_LIGHT_TEMPO	(200)
+
+/* converts an r_str() input to an active high, bits string : 000BAOSE */
+#define PNL_PINPUT(a)		((((unsigned char)(a)) ^ 0x7F) >> 3)
+
+#define PNL_PBUSY		0x80	/* inverted input, active low */
+#define PNL_PACK		0x40	/* direct input, active low */
+#define PNL_POUTPA		0x20	/* direct input, active high */
+#define PNL_PSELECD		0x10	/* direct input, active high */
+#define PNL_PERRORP		0x08	/* direct input, active low */
+
+#define PNL_PBIDIR		0x20	/* bi-directional ports */
+/* high to read data in or-ed with data out */
+#define PNL_PINTEN		0x10
+#define PNL_PSELECP		0x08	/* inverted output, active low */
+#define PNL_PINITP		0x04	/* direct output, active low */
+#define PNL_PAUTOLF		0x02	/* inverted output, active low */
+#define PNL_PSTROBE		0x01	/* inverted output */
+
+#define PNL_PD0			0x01
+#define PNL_PD1			0x02
+#define PNL_PD2			0x04
+#define PNL_PD3			0x08
+#define PNL_PD4			0x10
+#define PNL_PD5			0x20
+#define PNL_PD6			0x40
+#define PNL_PD7			0x80
+
+#define PIN_NONE		0
+#define PIN_STROBE		1
+#define PIN_D0			2
+#define PIN_D1			3
+#define PIN_D2			4
+#define PIN_D3			5
+#define PIN_D4			6
+#define PIN_D5			7
+#define PIN_D6			8
+#define PIN_D7			9
+#define PIN_AUTOLF		14
+#define PIN_INITP		16
+#define PIN_SELECP		17
+#define PIN_NOT_SET		127
+
+#define LCD_FLAG_S		0x0001
+#define LCD_FLAG_ID		0x0002
+#define LCD_FLAG_B		0x0004	/* blink on */
+#define LCD_FLAG_C		0x0008	/* cursor on */
+#define LCD_FLAG_D		0x0010	/* display on */
+#define LCD_FLAG_F		0x0020	/* large font mode */
+#define LCD_FLAG_N		0x0040	/* 2-rows mode */
+#define LCD_FLAG_L		0x0080	/* backlight enabled */
+
+/* LCD commands */
+#define LCD_CMD_DISPLAY_CLEAR	0x01	/* Clear entire display */
+
+#define LCD_CMD_ENTRY_MODE	0x04	/* Set entry mode */
+#define LCD_CMD_CURSOR_INC	0x02	/* Increment cursor */
+
+#define LCD_CMD_DISPLAY_CTRL	0x08	/* Display control */
+#define LCD_CMD_DISPLAY_ON	0x04	/* Set display on */
+#define LCD_CMD_CURSOR_ON	0x02	/* Set cursor on */
+#define LCD_CMD_BLINK_ON	0x01	/* Set blink on */
+
+#define LCD_CMD_SHIFT		0x10	/* Shift cursor/display */
+#define LCD_CMD_DISPLAY_SHIFT	0x08	/* Shift display instead of cursor */
+#define LCD_CMD_SHIFT_RIGHT	0x04	/* Shift display/cursor to the right */
+
+#define LCD_CMD_FUNCTION_SET	0x20	/* Set function */
+#define LCD_CMD_DATA_LEN_8BITS	0x10	/* Set data length to 8 bits */
+#define LCD_CMD_TWO_LINES	0x08	/* Set to two display lines */
+#define LCD_CMD_FONT_5X10_DOTS	0x04	/* Set char font to 5x10 dots */
+
+#define LCD_CMD_SET_CGRAM_ADDR	0x40	/* Set char generator RAM address */
+
+#define LCD_CMD_SET_DDRAM_ADDR	0x80	/* Set display data RAM address */
+
+#define LCD_ESCAPE_LEN		24	/* max chars for LCD escape command */
+#define LCD_ESCAPE_CHAR	27	/* use char 27 for escape command */
+
+#define NOT_SET			-1
+
+/* macros to simplify use of the parallel port */
+#define r_ctr(x)        (parport_read_control((x)->port))
+#define r_dtr(x)        (parport_read_data((x)->port))
+#define r_str(x)        (parport_read_status((x)->port))
+#define w_ctr(x, y)     (parport_write_control((x)->port, (y)))
+#define w_dtr(x, y)     (parport_write_data((x)->port, (y)))
+
+/* this defines which bits are to be used and which ones to be ignored */
+/* logical or of the output bits involved in the scan matrix */
+static __u8 scan_mask_o;
+/* logical or of the input bits involved in the scan matrix */
+static __u8 scan_mask_i;
+
+enum input_type {
+	INPUT_TYPE_STD,
+	INPUT_TYPE_KBD,
+};
+
+enum input_state {
+	INPUT_ST_LOW,
+	INPUT_ST_RISING,
+	INPUT_ST_HIGH,
+	INPUT_ST_FALLING,
+};
+
+struct logical_input {
+	struct list_head list;
+	__u64 mask;
+	__u64 value;
+	enum input_type type;
+	enum input_state state;
+	__u8 rise_time, fall_time;
+	__u8 rise_timer, fall_timer, high_timer;
+
+	union {
+		struct {	/* valid when type == INPUT_TYPE_STD */
+			void (*press_fct)(int);
+			void (*release_fct)(int);
+			int press_data;
+			int release_data;
+		} std;
+		struct {	/* valid when type == INPUT_TYPE_KBD */
+			/* strings can be non null-terminated */
+			char press_str[sizeof(void *) + sizeof(int)];
+			char repeat_str[sizeof(void *) + sizeof(int)];
+			char release_str[sizeof(void *) + sizeof(int)];
+		} kbd;
+	} u;
+};
+
+static LIST_HEAD(logical_inputs);	/* list of all defined logical inputs */
+
+/* physical contacts history
+ * Physical contacts are a 45 bits string of 9 groups of 5 bits each.
+ * The 8 lower groups correspond to output bits 0 to 7, and the 9th group
+ * corresponds to the ground.
+ * Within each group, bits are stored in the same order as read on the port :
+ * BAPSE (busy=4, ack=3, paper empty=2, select=1, error=0).
+ * So, each __u64 is represented like this :
+ * 0000000000000000000BAPSEBAPSEBAPSEBAPSEBAPSEBAPSEBAPSEBAPSEBAPSE
+ * <-----unused------><gnd><d07><d06><d05><d04><d03><d02><d01><d00>
+ */
+
+/* what has just been read from the I/O ports */
+static __u64 phys_read;
+/* previous phys_read */
+static __u64 phys_read_prev;
+/* stabilized phys_read (phys_read|phys_read_prev) */
+static __u64 phys_curr;
+/* previous phys_curr */
+static __u64 phys_prev;
+/* 0 means that at least one logical signal needs be computed */
+static char inputs_stable;
+
+/* these variables are specific to the keypad */
+static struct {
+	bool enabled;
+} keypad;
+
+static char keypad_buffer[KEYPAD_BUFFER];
+static int keypad_buflen;
+static int keypad_start;
+static char keypressed;
+static wait_queue_head_t keypad_read_wait;
+
+/* lcd-specific variables */
+static struct {
+	bool enabled;
+	bool initialized;
+	bool must_clear;
+
+	int height;
+	int width;
+	int bwidth;
+	int hwidth;
+	int charset;
+	int proto;
+	int light_tempo;
+
+	/* TODO: use union here? */
+	struct {
+		int e;
+		int rs;
+		int rw;
+		int cl;
+		int da;
+		int bl;
+	} pins;
+
+	/* contains the LCD config state */
+	unsigned long int flags;
+
+	/* Contains the LCD X and Y offset */
+	struct {
+		unsigned long int x;
+		unsigned long int y;
+	} addr;
+
+	/* Current escape sequence and it's length or -1 if outside */
+	struct {
+		char buf[LCD_ESCAPE_LEN + 1];
+		int len;
+	} esc_seq;
+} lcd;
+
+/* Needed only for init */
+static int selected_lcd_type = NOT_SET;
+
+/*
+ * Bit masks to convert LCD signals to parallel port outputs.
+ * _d_ are values for data port, _c_ are for control port.
+ * [0] = signal OFF, [1] = signal ON, [2] = mask
+ */
+#define BIT_CLR		0
+#define BIT_SET		1
+#define BIT_MSK		2
+#define BIT_STATES	3
+/*
+ * one entry for each bit on the LCD
+ */
+#define LCD_BIT_E	0
+#define LCD_BIT_RS	1
+#define LCD_BIT_RW	2
+#define LCD_BIT_BL	3
+#define LCD_BIT_CL	4
+#define LCD_BIT_DA	5
+#define LCD_BITS	6
+
+/*
+ * each bit can be either connected to a DATA or CTRL port
+ */
+#define LCD_PORT_C	0
+#define LCD_PORT_D	1
+#define LCD_PORTS	2
+
+static unsigned char lcd_bits[LCD_PORTS][LCD_BITS][BIT_STATES];
+
+/*
+ * LCD protocols
+ */
+#define LCD_PROTO_PARALLEL      0
+#define LCD_PROTO_SERIAL        1
+#define LCD_PROTO_TI_DA8XX_LCD	2
+
+/*
+ * LCD character sets
+ */
+#define LCD_CHARSET_NORMAL      0
+#define LCD_CHARSET_KS0074      1
+
+/*
+ * LCD types
+ */
+#define LCD_TYPE_NONE		0
+#define LCD_TYPE_CUSTOM		1
+#define LCD_TYPE_OLD		2
+#define LCD_TYPE_KS0074		3
+#define LCD_TYPE_HANTRONIX	4
+#define LCD_TYPE_NEXCOM		5
+
+/*
+ * keypad types
+ */
+#define KEYPAD_TYPE_NONE	0
+#define KEYPAD_TYPE_OLD		1
+#define KEYPAD_TYPE_NEW		2
+#define KEYPAD_TYPE_NEXCOM	3
+
+/*
+ * panel profiles
+ */
+#define PANEL_PROFILE_CUSTOM	0
+#define PANEL_PROFILE_OLD	1
+#define PANEL_PROFILE_NEW	2
+#define PANEL_PROFILE_HANTRONIX	3
+#define PANEL_PROFILE_NEXCOM	4
+#define PANEL_PROFILE_LARGE	5
+
+/*
+ * Construct custom config from the kernel's configuration
+ */
+#define DEFAULT_PARPORT         0
+#define DEFAULT_PROFILE         PANEL_PROFILE_LARGE
+#define DEFAULT_KEYPAD_TYPE     KEYPAD_TYPE_OLD
+#define DEFAULT_LCD_TYPE        LCD_TYPE_OLD
+#define DEFAULT_LCD_HEIGHT      2
+#define DEFAULT_LCD_WIDTH       40
+#define DEFAULT_LCD_BWIDTH      40
+#define DEFAULT_LCD_HWIDTH      64
+#define DEFAULT_LCD_CHARSET     LCD_CHARSET_NORMAL
+#define DEFAULT_LCD_PROTO       LCD_PROTO_PARALLEL
+
+#define DEFAULT_LCD_PIN_E       PIN_AUTOLF
+#define DEFAULT_LCD_PIN_RS      PIN_SELECP
+#define DEFAULT_LCD_PIN_RW      PIN_INITP
+#define DEFAULT_LCD_PIN_SCL     PIN_STROBE
+#define DEFAULT_LCD_PIN_SDA     PIN_D0
+#define DEFAULT_LCD_PIN_BL      PIN_NOT_SET
+
+#ifdef CONFIG_PANEL_PARPORT
+#undef DEFAULT_PARPORT
+#define DEFAULT_PARPORT CONFIG_PANEL_PARPORT
+#endif
+
+#ifdef CONFIG_PANEL_PROFILE
+#undef DEFAULT_PROFILE
+#define DEFAULT_PROFILE CONFIG_PANEL_PROFILE
+#endif
+
+#if DEFAULT_PROFILE == 0	/* custom */
+#ifdef CONFIG_PANEL_KEYPAD
+#undef DEFAULT_KEYPAD_TYPE
+#define DEFAULT_KEYPAD_TYPE CONFIG_PANEL_KEYPAD
+#endif
+
+#ifdef CONFIG_PANEL_LCD
+#undef DEFAULT_LCD_TYPE
+#define DEFAULT_LCD_TYPE CONFIG_PANEL_LCD
+#endif
+
+#ifdef CONFIG_PANEL_LCD_HEIGHT
+#undef DEFAULT_LCD_HEIGHT
+#define DEFAULT_LCD_HEIGHT CONFIG_PANEL_LCD_HEIGHT
+#endif
+
+#ifdef CONFIG_PANEL_LCD_WIDTH
+#undef DEFAULT_LCD_WIDTH
+#define DEFAULT_LCD_WIDTH CONFIG_PANEL_LCD_WIDTH
+#endif
+
+#ifdef CONFIG_PANEL_LCD_BWIDTH
+#undef DEFAULT_LCD_BWIDTH
+#define DEFAULT_LCD_BWIDTH CONFIG_PANEL_LCD_BWIDTH
+#endif
+
+#ifdef CONFIG_PANEL_LCD_HWIDTH
+#undef DEFAULT_LCD_HWIDTH
+#define DEFAULT_LCD_HWIDTH CONFIG_PANEL_LCD_HWIDTH
+#endif
+
+#ifdef CONFIG_PANEL_LCD_CHARSET
+#undef DEFAULT_LCD_CHARSET
+#define DEFAULT_LCD_CHARSET CONFIG_PANEL_LCD_CHARSET
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PROTO
+#undef DEFAULT_LCD_PROTO
+#define DEFAULT_LCD_PROTO CONFIG_PANEL_LCD_PROTO
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_E
+#undef DEFAULT_LCD_PIN_E
+#define DEFAULT_LCD_PIN_E CONFIG_PANEL_LCD_PIN_E
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_RS
+#undef DEFAULT_LCD_PIN_RS
+#define DEFAULT_LCD_PIN_RS CONFIG_PANEL_LCD_PIN_RS
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_RW
+#undef DEFAULT_LCD_PIN_RW
+#define DEFAULT_LCD_PIN_RW CONFIG_PANEL_LCD_PIN_RW
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_SCL
+#undef DEFAULT_LCD_PIN_SCL
+#define DEFAULT_LCD_PIN_SCL CONFIG_PANEL_LCD_PIN_SCL
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_SDA
+#undef DEFAULT_LCD_PIN_SDA
+#define DEFAULT_LCD_PIN_SDA CONFIG_PANEL_LCD_PIN_SDA
+#endif
+
+#ifdef CONFIG_PANEL_LCD_PIN_BL
+#undef DEFAULT_LCD_PIN_BL
+#define DEFAULT_LCD_PIN_BL CONFIG_PANEL_LCD_PIN_BL
+#endif
+
+#endif /* DEFAULT_PROFILE == 0 */
+
+/* global variables */
+
+/* Device single-open policy control */
+static atomic_t lcd_available = ATOMIC_INIT(1);
+static atomic_t keypad_available = ATOMIC_INIT(1);
+
+static struct pardevice *pprt;
+
+static int keypad_initialized;
+
+static void (*lcd_write_cmd)(int);
+static void (*lcd_write_data)(int);
+static void (*lcd_clear_fast)(void);
+
+static DEFINE_SPINLOCK(pprt_lock);
+static struct timer_list scan_timer;
+
+MODULE_DESCRIPTION("Generic parallel port LCD/Keypad driver");
+
+static int parport = DEFAULT_PARPORT;
+module_param(parport, int, 0000);
+MODULE_PARM_DESC(parport, "Parallel port index (0=lpt1, 1=lpt2, ...)");
+
+static int profile = DEFAULT_PROFILE;
+module_param(profile, int, 0000);
+MODULE_PARM_DESC(profile,
+		 "1=16x2 old kp; 2=serial 16x2, new kp; 3=16x2 hantronix; "
+		 "4=16x2 nexcom; default=40x2, old kp");
+
+static int keypad_type = NOT_SET;
+module_param(keypad_type, int, 0000);
+MODULE_PARM_DESC(keypad_type,
+		 "Keypad type: 0=none, 1=old 6 keys, 2=new 6+1 keys, 3=nexcom 4 keys");
+
+static int lcd_type = NOT_SET;
+module_param(lcd_type, int, 0000);
+MODULE_PARM_DESC(lcd_type,
+		 "LCD type: 0=none, 1=compiled-in, 2=old, 3=serial ks0074, 4=hantronix, 5=nexcom");
+
+static int lcd_height = NOT_SET;
+module_param(lcd_height, int, 0000);
+MODULE_PARM_DESC(lcd_height, "Number of lines on the LCD");
+
+static int lcd_width = NOT_SET;
+module_param(lcd_width, int, 0000);
+MODULE_PARM_DESC(lcd_width, "Number of columns on the LCD");
+
+static int lcd_bwidth = NOT_SET;	/* internal buffer width (usually 40) */
+module_param(lcd_bwidth, int, 0000);
+MODULE_PARM_DESC(lcd_bwidth, "Internal LCD line width (40)");
+
+static int lcd_hwidth = NOT_SET;	/* hardware buffer width (usually 64) */
+module_param(lcd_hwidth, int, 0000);
+MODULE_PARM_DESC(lcd_hwidth, "LCD line hardware address (64)");
+
+static int lcd_charset = NOT_SET;
+module_param(lcd_charset, int, 0000);
+MODULE_PARM_DESC(lcd_charset, "LCD character set: 0=standard, 1=KS0074");
+
+static int lcd_proto = NOT_SET;
+module_param(lcd_proto, int, 0000);
+MODULE_PARM_DESC(lcd_proto,
+		 "LCD communication: 0=parallel (//), 1=serial, 2=TI LCD Interface");
+
+/*
+ * These are the parallel port pins the LCD control signals are connected to.
+ * Set this to 0 if the signal is not used. Set it to its opposite value
+ * (negative) if the signal is negated. -MAXINT is used to indicate that the
+ * pin has not been explicitly specified.
+ *
+ * WARNING! no check will be performed about collisions with keypad !
+ */
+
+static int lcd_e_pin  = PIN_NOT_SET;
+module_param(lcd_e_pin, int, 0000);
+MODULE_PARM_DESC(lcd_e_pin,
+		 "# of the // port pin connected to LCD 'E' signal, with polarity (-17..17)");
+
+static int lcd_rs_pin = PIN_NOT_SET;
+module_param(lcd_rs_pin, int, 0000);
+MODULE_PARM_DESC(lcd_rs_pin,
+		 "# of the // port pin connected to LCD 'RS' signal, with polarity (-17..17)");
+
+static int lcd_rw_pin = PIN_NOT_SET;
+module_param(lcd_rw_pin, int, 0000);
+MODULE_PARM_DESC(lcd_rw_pin,
+		 "# of the // port pin connected to LCD 'RW' signal, with polarity (-17..17)");
+
+static int lcd_cl_pin = PIN_NOT_SET;
+module_param(lcd_cl_pin, int, 0000);
+MODULE_PARM_DESC(lcd_cl_pin,
+		 "# of the // port pin connected to serial LCD 'SCL' signal, with polarity (-17..17)");
+
+static int lcd_da_pin = PIN_NOT_SET;
+module_param(lcd_da_pin, int, 0000);
+MODULE_PARM_DESC(lcd_da_pin,
+		 "# of the // port pin connected to serial LCD 'SDA' signal, with polarity (-17..17)");
+
+static int lcd_bl_pin = PIN_NOT_SET;
+module_param(lcd_bl_pin, int, 0000);
+MODULE_PARM_DESC(lcd_bl_pin,
+		 "# of the // port pin connected to LCD backlight, with polarity (-17..17)");
+
+/* Deprecated module parameters - consider not using them anymore */
+
+static int lcd_enabled = NOT_SET;
+module_param(lcd_enabled, int, 0000);
+MODULE_PARM_DESC(lcd_enabled, "Deprecated option, use lcd_type instead");
+
+static int keypad_enabled = NOT_SET;
+module_param(keypad_enabled, int, 0000);
+MODULE_PARM_DESC(keypad_enabled, "Deprecated option, use keypad_type instead");
+
+static const unsigned char *lcd_char_conv;
+
+/* for some LCD drivers (ks0074) we need a charset conversion table. */
+static const unsigned char lcd_char_conv_ks0074[256] = {
+	/*          0|8   1|9   2|A   3|B   4|C   5|D   6|E   7|F */
+	/* 0x00 */ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
+	/* 0x08 */ 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+	/* 0x10 */ 0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17,
+	/* 0x18 */ 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f,
+	/* 0x20 */ 0x20, 0x21, 0x22, 0x23, 0xa2, 0x25, 0x26, 0x27,
+	/* 0x28 */ 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f,
+	/* 0x30 */ 0x30, 0x31, 0x32, 0x33, 0x34, 0x35, 0x36, 0x37,
+	/* 0x38 */ 0x38, 0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f,
+	/* 0x40 */ 0xa0, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,
+	/* 0x48 */ 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f,
+	/* 0x50 */ 0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57,
+	/* 0x58 */ 0x58, 0x59, 0x5a, 0xfa, 0xfb, 0xfc, 0x1d, 0xc4,
+	/* 0x60 */ 0x96, 0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67,
+	/* 0x68 */ 0x68, 0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f,
+	/* 0x70 */ 0x70, 0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77,
+	/* 0x78 */ 0x78, 0x79, 0x7a, 0xfd, 0xfe, 0xff, 0xce, 0x20,
+	/* 0x80 */ 0x80, 0x81, 0x82, 0x83, 0x84, 0x85, 0x86, 0x87,
+	/* 0x88 */ 0x88, 0x89, 0x8a, 0x8b, 0x8c, 0x8d, 0x8e, 0x8f,
+	/* 0x90 */ 0x90, 0x91, 0x92, 0x93, 0x94, 0x95, 0x96, 0x97,
+	/* 0x98 */ 0x98, 0x99, 0x9a, 0x9b, 0x9c, 0x9d, 0x9e, 0x9f,
+	/* 0xA0 */ 0x20, 0x40, 0xb1, 0xa1, 0x24, 0xa3, 0xfe, 0x5f,
+	/* 0xA8 */ 0x22, 0xc8, 0x61, 0x14, 0x97, 0x2d, 0xad, 0x96,
+	/* 0xB0 */ 0x80, 0x8c, 0x82, 0x83, 0x27, 0x8f, 0x86, 0xdd,
+	/* 0xB8 */ 0x2c, 0x81, 0x6f, 0x15, 0x8b, 0x8a, 0x84, 0x60,
+	/* 0xC0 */ 0xe2, 0xe2, 0xe2, 0x5b, 0x5b, 0xae, 0xbc, 0xa9,
+	/* 0xC8 */ 0xc5, 0xbf, 0xc6, 0xf1, 0xe3, 0xe3, 0xe3, 0xe3,
+	/* 0xD0 */ 0x44, 0x5d, 0xa8, 0xe4, 0xec, 0xec, 0x5c, 0x78,
+	/* 0xD8 */ 0xab, 0xa6, 0xe5, 0x5e, 0x5e, 0xe6, 0xaa, 0xbe,
+	/* 0xE0 */ 0x7f, 0xe7, 0xaf, 0x7b, 0x7b, 0xaf, 0xbd, 0xc8,
+	/* 0xE8 */ 0xa4, 0xa5, 0xc7, 0xf6, 0xa7, 0xe8, 0x69, 0x69,
+	/* 0xF0 */ 0xed, 0x7d, 0xa8, 0xe4, 0xec, 0x5c, 0x5c, 0x25,
+	/* 0xF8 */ 0xac, 0xa6, 0xea, 0xef, 0x7e, 0xeb, 0xb2, 0x79,
+};
+
+static const char old_keypad_profile[][4][9] = {
+	{"S0", "Left\n", "Left\n", ""},
+	{"S1", "Down\n", "Down\n", ""},
+	{"S2", "Up\n", "Up\n", ""},
+	{"S3", "Right\n", "Right\n", ""},
+	{"S4", "Esc\n", "Esc\n", ""},
+	{"S5", "Ret\n", "Ret\n", ""},
+	{"", "", "", ""}
+};
+
+/* signals, press, repeat, release */
+static const char new_keypad_profile[][4][9] = {
+	{"S0", "Left\n", "Left\n", ""},
+	{"S1", "Down\n", "Down\n", ""},
+	{"S2", "Up\n", "Up\n", ""},
+	{"S3", "Right\n", "Right\n", ""},
+	{"S4s5", "", "Esc\n", "Esc\n"},
+	{"s4S5", "", "Ret\n", "Ret\n"},
+	{"S4S5", "Help\n", "", ""},
+	/* add new signals above this line */
+	{"", "", "", ""}
+};
+
+/* signals, press, repeat, release */
+static const char nexcom_keypad_profile[][4][9] = {
+	{"a-p-e-", "Down\n", "Down\n", ""},
+	{"a-p-E-", "Ret\n", "Ret\n", ""},
+	{"a-P-E-", "Esc\n", "Esc\n", ""},
+	{"a-P-e-", "Up\n", "Up\n", ""},
+	/* add new signals above this line */
+	{"", "", "", ""}
+};
+
+static const char (*keypad_profile)[4][9] = old_keypad_profile;
+
+static DECLARE_BITMAP(bits, LCD_BITS);
+
+static void lcd_get_bits(unsigned int port, int *val)
+{
+	unsigned int bit, state;
+
+	for (bit = 0; bit < LCD_BITS; bit++) {
+		state = test_bit(bit, bits) ? BIT_SET : BIT_CLR;
+		*val &= lcd_bits[port][bit][BIT_MSK];
+		*val |= lcd_bits[port][bit][state];
+	}
+}
+
+static void init_scan_timer(void);
+
+/* sets data port bits according to current signals values */
+static int set_data_bits(void)
+{
+	int val;
+
+	val = r_dtr(pprt);
+	lcd_get_bits(LCD_PORT_D, &val);
+	w_dtr(pprt, val);
+	return val;
+}
+
+/* sets ctrl port bits according to current signals values */
+static int set_ctrl_bits(void)
+{
+	int val;
+
+	val = r_ctr(pprt);
+	lcd_get_bits(LCD_PORT_C, &val);
+	w_ctr(pprt, val);
+	return val;
+}
+
+/* sets ctrl & data port bits according to current signals values */
+static void panel_set_bits(void)
+{
+	set_data_bits();
+	set_ctrl_bits();
+}
+
+/*
+ * Converts a parallel port pin (from -25 to 25) to data and control ports
+ * masks, and data and control port bits. The signal will be considered
+ * unconnected if it's on pin 0 or an invalid pin (<-25 or >25).
+ *
+ * Result will be used this way :
+ *   out(dport, in(dport) & d_val[2] | d_val[signal_state])
+ *   out(cport, in(cport) & c_val[2] | c_val[signal_state])
+ */
+static void pin_to_bits(int pin, unsigned char *d_val, unsigned char *c_val)
+{
+	int d_bit, c_bit, inv;
+
+	d_val[0] = 0;
+	c_val[0] = 0;
+	d_val[1] = 0;
+	c_val[1] = 0;
+	d_val[2] = 0xFF;
+	c_val[2] = 0xFF;
+
+	if (pin == 0)
+		return;
+
+	inv = (pin < 0);
+	if (inv)
+		pin = -pin;
+
+	d_bit = 0;
+	c_bit = 0;
+
+	switch (pin) {
+	case PIN_STROBE:	/* strobe, inverted */
+		c_bit = PNL_PSTROBE;
+		inv = !inv;
+		break;
+	case PIN_D0...PIN_D7:	/* D0 - D7 = 2 - 9 */
+		d_bit = 1 << (pin - 2);
+		break;
+	case PIN_AUTOLF:	/* autofeed, inverted */
+		c_bit = PNL_PAUTOLF;
+		inv = !inv;
+		break;
+	case PIN_INITP:		/* init, direct */
+		c_bit = PNL_PINITP;
+		break;
+	case PIN_SELECP:	/* select_in, inverted */
+		c_bit = PNL_PSELECP;
+		inv = !inv;
+		break;
+	default:		/* unknown pin, ignore */
+		break;
+	}
+
+	if (c_bit) {
+		c_val[2] &= ~c_bit;
+		c_val[!inv] = c_bit;
+	} else if (d_bit) {
+		d_val[2] &= ~d_bit;
+		d_val[!inv] = d_bit;
+	}
+}
+
+/* sleeps that many milliseconds with a reschedule */
+static void long_sleep(int ms)
+{
+	if (in_interrupt())
+		mdelay(ms);
+	else
+		schedule_timeout_interruptible(msecs_to_jiffies(ms));
+}
+
+/*
+ * send a serial byte to the LCD panel. The caller is responsible for locking
+ * if needed.
+ */
+static void lcd_send_serial(int byte)
+{
+	int bit;
+
+	/*
+	 * the data bit is set on D0, and the clock on STROBE.
+	 * LCD reads D0 on STROBE's rising edge.
+	 */
+	for (bit = 0; bit < 8; bit++) {
+		clear_bit(LCD_BIT_CL, bits);	/* CLK low */
+		panel_set_bits();
+		if (byte & 1) {
+			set_bit(LCD_BIT_DA, bits);
+		} else {
+			clear_bit(LCD_BIT_DA, bits);
+		}
+
+		panel_set_bits();
+		udelay(2);  /* maintain the data during 2 us before CLK up */
+		set_bit(LCD_BIT_CL, bits);	/* CLK high */
+		panel_set_bits();
+		udelay(1);  /* maintain the strobe during 1 us */
+		byte >>= 1;
+	}
+}
+
+/* turn the backlight on or off */
+static void lcd_backlight(int on)
+{
+	if (lcd.pins.bl == PIN_NONE)
+		return;
+
+	/* The backlight is activated by setting the AUTOFEED line to +5V  */
+	spin_lock_irq(&pprt_lock);
+	if (on)
+		set_bit(LCD_BIT_BL, bits);
+	else
+		clear_bit(LCD_BIT_BL, bits);
+	panel_set_bits();
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send a command to the LCD panel in serial mode */
+static void lcd_write_cmd_s(int cmd)
+{
+	spin_lock_irq(&pprt_lock);
+	lcd_send_serial(0x1F);	/* R/W=W, RS=0 */
+	lcd_send_serial(cmd & 0x0F);
+	lcd_send_serial((cmd >> 4) & 0x0F);
+	udelay(40);		/* the shortest command takes at least 40 us */
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send data to the LCD panel in serial mode */
+static void lcd_write_data_s(int data)
+{
+	spin_lock_irq(&pprt_lock);
+	lcd_send_serial(0x5F);	/* R/W=W, RS=1 */
+	lcd_send_serial(data & 0x0F);
+	lcd_send_serial((data >> 4) & 0x0F);
+	udelay(40);		/* the shortest data takes at least 40 us */
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send a command to the LCD panel in 8 bits parallel mode */
+static void lcd_write_cmd_p8(int cmd)
+{
+	spin_lock_irq(&pprt_lock);
+	/* present the data to the data port */
+	w_dtr(pprt, cmd);
+	udelay(20);	/* maintain the data during 20 us before the strobe */
+
+	set_bit(LCD_BIT_E, bits);
+	clear_bit(LCD_BIT_RS, bits);
+	clear_bit(LCD_BIT_RW, bits);
+	set_ctrl_bits();
+
+	udelay(40);	/* maintain the strobe during 40 us */
+
+	clear_bit(LCD_BIT_E, bits);
+	set_ctrl_bits();
+
+	udelay(120);	/* the shortest command takes at least 120 us */
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send data to the LCD panel in 8 bits parallel mode */
+static void lcd_write_data_p8(int data)
+{
+	spin_lock_irq(&pprt_lock);
+	/* present the data to the data port */
+	w_dtr(pprt, data);
+	udelay(20);	/* maintain the data during 20 us before the strobe */
+
+	set_bit(LCD_BIT_E, bits);
+	set_bit(LCD_BIT_RS, bits);
+	clear_bit(LCD_BIT_RW, bits);
+	set_ctrl_bits();
+
+	udelay(40);	/* maintain the strobe during 40 us */
+
+	clear_bit(LCD_BIT_E, bits);
+	set_ctrl_bits();
+
+	udelay(45);	/* the shortest data takes at least 45 us */
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send a command to the TI LCD panel */
+static void lcd_write_cmd_tilcd(int cmd)
+{
+	spin_lock_irq(&pprt_lock);
+	/* present the data to the control port */
+	w_ctr(pprt, cmd);
+	udelay(60);
+	spin_unlock_irq(&pprt_lock);
+}
+
+/* send data to the TI LCD panel */
+static void lcd_write_data_tilcd(int data)
+{
+	spin_lock_irq(&pprt_lock);
+	/* present the data to the data port */
+	w_dtr(pprt, data);
+	udelay(60);
+	spin_unlock_irq(&pprt_lock);
+}
+
+static void lcd_gotoxy(void)
+{
+	lcd_write_cmd(LCD_CMD_SET_DDRAM_ADDR
+		      | (lcd.addr.y ? lcd.hwidth : 0)
+		      /*
+		       * we force the cursor to stay at the end of the
+		       * line if it wants to go farther
+		       */
+		      | ((lcd.addr.x < lcd.bwidth) ? lcd.addr.x &
+			 (lcd.hwidth - 1) : lcd.bwidth - 1));
+}
+
+static void lcd_print(char c)
+{
+	if (lcd.addr.x < lcd.bwidth) {
+		if (lcd_char_conv)
+			c = lcd_char_conv[(unsigned char)c];
+		lcd_write_data(c);
+		lcd.addr.x++;
+	}
+	/* prevents the cursor from wrapping onto the next line */
+	if (lcd.addr.x == lcd.bwidth)
+		lcd_gotoxy();
+}
+
+/* fills the display with spaces and resets X/Y */
+static void lcd_clear_fast_s(void)
+{
+	int pos;
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+
+	spin_lock_irq(&pprt_lock);
+	for (pos = 0; pos < lcd.height * lcd.hwidth; pos++) {
+		lcd_send_serial(0x5F);	/* R/W=W, RS=1 */
+		lcd_send_serial(' ' & 0x0F);
+		lcd_send_serial((' ' >> 4) & 0x0F);
+		/* the shortest data takes at least 40 us */
+		udelay(40);
+	}
+	spin_unlock_irq(&pprt_lock);
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+}
+
+/* fills the display with spaces and resets X/Y */
+static void lcd_clear_fast_p8(void)
+{
+	int pos;
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+
+	spin_lock_irq(&pprt_lock);
+	for (pos = 0; pos < lcd.height * lcd.hwidth; pos++) {
+		/* present the data to the data port */
+		w_dtr(pprt, ' ');
+
+		/* maintain the data during 20 us before the strobe */
+		udelay(20);
+
+		set_bit(LCD_BIT_E, bits);
+		set_bit(LCD_BIT_RS, bits);
+		clear_bit(LCD_BIT_RW, bits);
+		set_ctrl_bits();
+
+		/* maintain the strobe during 40 us */
+		udelay(40);
+
+		clear_bit(LCD_BIT_E, bits);
+		set_ctrl_bits();
+
+		/* the shortest data takes at least 45 us */
+		udelay(45);
+	}
+	spin_unlock_irq(&pprt_lock);
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+}
+
+/* fills the display with spaces and resets X/Y */
+static void lcd_clear_fast_tilcd(void)
+{
+	int pos;
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+
+	spin_lock_irq(&pprt_lock);
+	for (pos = 0; pos < lcd.height * lcd.hwidth; pos++) {
+		/* present the data to the data port */
+		w_dtr(pprt, ' ');
+		udelay(60);
+	}
+
+	spin_unlock_irq(&pprt_lock);
+
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	lcd_gotoxy();
+}
+
+/* clears the display and resets X/Y */
+static void lcd_clear_display(void)
+{
+	lcd_write_cmd(LCD_CMD_DISPLAY_CLEAR);
+	lcd.addr.x = 0;
+	lcd.addr.y = 0;
+	/* we must wait a few milliseconds (15) */
+	long_sleep(15);
+}
+
+static void lcd_init_display(void)
+{
+	lcd.flags = ((lcd.height > 1) ? LCD_FLAG_N : 0)
+	    | LCD_FLAG_D | LCD_FLAG_C | LCD_FLAG_B;
+
+	long_sleep(20);		/* wait 20 ms after power-up for the paranoid */
+
+	/* 8bits, 1 line, small fonts; let's do it 3 times */
+	lcd_write_cmd(LCD_CMD_FUNCTION_SET | LCD_CMD_DATA_LEN_8BITS);
+	long_sleep(10);
+	lcd_write_cmd(LCD_CMD_FUNCTION_SET | LCD_CMD_DATA_LEN_8BITS);
+	long_sleep(10);
+	lcd_write_cmd(LCD_CMD_FUNCTION_SET | LCD_CMD_DATA_LEN_8BITS);
+	long_sleep(10);
+
+	/* set font height and lines number */
+	lcd_write_cmd(LCD_CMD_FUNCTION_SET | LCD_CMD_DATA_LEN_8BITS
+		      | ((lcd.flags & LCD_FLAG_F) ? LCD_CMD_FONT_5X10_DOTS : 0)
+		      | ((lcd.flags & LCD_FLAG_N) ? LCD_CMD_TWO_LINES : 0)
+	    );
+	long_sleep(10);
+
+	/* display off, cursor off, blink off */
+	lcd_write_cmd(LCD_CMD_DISPLAY_CTRL);
+	long_sleep(10);
+
+	lcd_write_cmd(LCD_CMD_DISPLAY_CTRL	/* set display mode */
+		      | ((lcd.flags & LCD_FLAG_D) ? LCD_CMD_DISPLAY_ON : 0)
+		      | ((lcd.flags & LCD_FLAG_C) ? LCD_CMD_CURSOR_ON : 0)
+		      | ((lcd.flags & LCD_FLAG_B) ? LCD_CMD_BLINK_ON : 0)
+	    );
+
+	lcd_backlight((lcd.flags & LCD_FLAG_L) ? 1 : 0);
+
+	long_sleep(10);
+
+	/* entry mode set : increment, cursor shifting */
+	lcd_write_cmd(LCD_CMD_ENTRY_MODE | LCD_CMD_CURSOR_INC);
+
+	lcd_clear_display();
+}
+
+/*
+ * These are the file operation function for user access to /dev/lcd
+ * This function can also be called from inside the kernel, by
+ * setting file and ppos to NULL.
+ *
+ */
+
+static inline int handle_lcd_special_code(void)
+{
+	/* LCD special codes */
+
+	int processed = 0;
+
+	char *esc = lcd.esc_seq.buf + 2;
+	int oldflags = lcd.flags;
+
+	/* check for display mode flags */
+	switch (*esc) {
+	case 'D':	/* Display ON */
+		lcd.flags |= LCD_FLAG_D;
+		processed = 1;
+		break;
+	case 'd':	/* Display OFF */
+		lcd.flags &= ~LCD_FLAG_D;
+		processed = 1;
+		break;
+	case 'C':	/* Cursor ON */