Merge tag 'phy-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.10

Merge contains:
 *) Add new usb2 phy driver for Meson8b and GXBB
 *) Remove phy drivers added for miphy365 and STiH415/6 (as support for
    these SoCs are removed from the kernel)
 *) Add a sysfs entry to facilitate usb role swap in rcar SoC
 *) Add support for otg port in rk3399
 *) misc fixes in various phy drivers and cleanups

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

21 files changed, 1024 insertions, 921 deletions

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index fe00f9134d51..e8eb7f225a88 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -129,16 +129,6 @@ config PHY_MIPHY28LP
 	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
 	  that is part of STMicroelectronics STiH407 SoC.
 
-config PHY_MIPHY365X
-	tristate "STMicroelectronics MIPHY365X PHY driver for STiH41x series"
-	depends on ARCH_STI
-	depends on HAS_IOMEM
-	depends on OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the miphy transceiver (for SATA/PCIE)
-	  that is part of STMicroelectronics STiH41x SoC series.
-
 config PHY_RCAR_GEN2
 	tristate "Renesas R-Car generation 2 USB PHY driver"
 	depends on ARCH_RENESAS
@@ -373,7 +363,9 @@ config PHY_ROCKCHIP_INNO_USB2
 	tristate "Rockchip INNO USB2PHY Driver"
 	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
 	depends on COMMON_CLK
+	depends on USB_SUPPORT
 	select GENERIC_PHY
+	select USB_COMMON
 	help
 	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
 
@@ -438,14 +430,6 @@ config PHY_STIH407_USB
 	  Enable this support to enable the picoPHY device used by USB2
 	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
 
-config PHY_STIH41X_USB
-	tristate "STMicroelectronics USB2 PHY driver for STiH41x series"
-	depends on ARCH_STI
-	select GENERIC_PHY
-	help
-	  Enable this to support the USB transceiver that is part of
-	  STMicroelectronics STiH41x SoC series.
-
 config PHY_QCOM_UFS
 	tristate "Qualcomm UFS PHY driver"
 	depends on OF && ARCH_QCOM
@@ -489,4 +473,17 @@ config PHY_NS2_PCIE
 	help
 	  Enable this to support the Broadcom Northstar2 PCIe PHY.
 	  If unsure, say N.
+
+config PHY_MESON8B_USB2
+	tristate "Meson8b and GXBB USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson8b
+	  and GXBB SoCs.
+	  If unsure, say N.
+
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index a534cf5be07d..65eb2f436a41 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -18,7 +18,6 @@ obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
 obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
-obj-$(CONFIG_PHY_MIPHY365X)		+= phy-miphy365x.o
 obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
 obj-$(CONFIG_PHY_RCAR_GEN3_USB2)	+= phy-rcar-gen3-usb2.o
 obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
@@ -50,7 +49,6 @@ obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
 obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
 obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
-obj-$(CONFIG_PHY_STIH41X_USB)		+= phy-stih41x-usb.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
@@ -60,3 +58,4 @@ obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
 obj-$(CONFIG_ARCH_TEGRA) += tegra/
 obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
+obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
diff --git a/drivers/phy/phy-berlin-sata.c b/drivers/phy/phy-berlin-sata.c
index f84a33a1bdd9..2c7a57f2d595 100644
--- a/drivers/phy/phy-berlin-sata.c
+++ b/drivers/phy/phy-berlin-sata.c
@@ -85,7 +85,6 @@ static int phy_berlin_sata_power_on(struct phy *phy)
 	struct phy_berlin_desc *desc = phy_get_drvdata(phy);
 	struct phy_berlin_priv *priv = dev_get_drvdata(phy->dev.parent);
 	void __iomem *ctrl_reg = priv->base + 0x60 + (desc->index * 0x80);
-	int ret = 0;
 	u32 regval;
 
 	clk_prepare_enable(priv->clk);
@@ -130,7 +129,7 @@ static int phy_berlin_sata_power_on(struct phy *phy)
 
 	clk_disable_unprepare(priv->clk);
 
-	return ret;
+	return 0;
 }
 
 static int phy_berlin_sata_power_off(struct phy *phy)
diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/phy-brcm-sata.c
index 8ffc44afdb75..ccbc3d994998 100644
--- a/drivers/phy/phy-brcm-sata.c
+++ b/drivers/phy/phy-brcm-sata.c
@@ -140,7 +140,7 @@ static inline void __iomem *brcm_sata_pcb_base(struct brcm_sata_port *port)
 	default:
 		dev_err(priv->dev, "invalid phy version\n");
 		break;
-	};
+	}
 
 	return priv->phy_base + (port->portnum * size);
 }
@@ -157,7 +157,7 @@ static inline void __iomem *brcm_sata_ctrl_base(struct brcm_sata_port *port)
 	default:
 		dev_err(priv->dev, "invalid phy version\n");
 		break;
-	};
+	}
 
 	return priv->ctrl_base + (port->portnum * size);
 }
@@ -365,7 +365,7 @@ static int brcm_sata_phy_init(struct phy *phy)
 		break;
 	default:
 		rc = -ENODEV;
-	};
+	}
 
 	return rc;
 }
diff --git a/drivers/phy/phy-da8xx-usb.c b/drivers/phy/phy-da8xx-usb.c
index c85fb0b59729..1b82bff6330f 100644
--- a/drivers/phy/phy-da8xx-usb.c
+++ b/drivers/phy/phy-da8xx-usb.c
@@ -23,6 +23,8 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 
+#define PHY_INIT_BITS	(CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN)
+
 struct da8xx_usb_phy {
 	struct phy_provider	*phy_provider;
 	struct phy		*usb11_phy;
@@ -208,6 +210,9 @@ static int da8xx_usb_phy_probe(struct platform_device *pdev)
 			dev_warn(dev, "Failed to create usb20 phy lookup\n");
 	}
 
+	regmap_write_bits(d_phy->regmap, CFGCHIP(2),
+			  PHY_INIT_BITS, PHY_INIT_BITS);
+
 	return 0;
 }
 
diff --git a/drivers/phy/phy-exynos-mipi-video.c b/drivers/phy/phy-exynos-mipi-video.c
index 8b851f718123..6bee04cc4d53 100644
--- a/drivers/phy/phy-exynos-mipi-video.c
+++ b/drivers/phy/phy-exynos-mipi-video.c
@@ -229,19 +229,6 @@ struct exynos_mipi_video_phy {
 	spinlock_t slock;
 };
 
-static inline int __is_running(const struct exynos_mipi_phy_desc *data,
-			struct exynos_mipi_video_phy *state)
-{
-	u32 val;
-	int ret;
-
-	ret = regmap_read(state->regmaps[data->resetn_map], data->resetn_reg, &val);
-	if (ret)
-		return 0;
-
-	return val & data->resetn_val;
-}
-
 static int __set_phy_state(const struct exynos_mipi_phy_desc *data,
 			   struct exynos_mipi_video_phy *state, unsigned int on)
 {
@@ -251,7 +238,7 @@ static int __set_phy_state(const struct exynos_mipi_phy_desc *data,
 
 	/* disable in PMU sysreg */
 	if (!on && data->coupled_phy_id >= 0 &&
-	    !__is_running(state->phys[data->coupled_phy_id].data, state)) {
+	    state->phys[data->coupled_phy_id].phy->power_count == 0) {
 		regmap_read(state->regmaps[data->enable_map], data->enable_reg,
 			    &val);
 		val &= ~data->enable_val;
diff --git a/drivers/phy/phy-exynos4210-usb2.c b/drivers/phy/phy-exynos4210-usb2.c
index f30bbb0fb3b2..1f50e1004828 100644
--- a/drivers/phy/phy-exynos4210-usb2.c
+++ b/drivers/phy/phy-exynos4210-usb2.c
@@ -141,7 +141,7 @@ static void exynos4210_isol(struct samsung_usb2_phy_instance *inst, bool on)
 		break;
 	default:
 		return;
-	};
+	}
 
 	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
 }
@@ -179,7 +179,7 @@ static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
 		rstbits =	EXYNOS_4210_URSTCON_PHY1_P1P2 |
 				EXYNOS_4210_URSTCON_HOST_LINK_P2;
 		break;
-	};
+	}
 
 	if (on) {
 		clk = readl(drv->reg_phy + EXYNOS_4210_UPHYCLK);
diff --git a/drivers/phy/phy-exynos4x12-usb2.c b/drivers/phy/phy-exynos4x12-usb2.c
index 765da90a536f..7f27a91acf87 100644
--- a/drivers/phy/phy-exynos4x12-usb2.c
+++ b/drivers/phy/phy-exynos4x12-usb2.c
@@ -187,7 +187,7 @@ static void exynos4x12_isol(struct samsung_usb2_phy_instance *inst, bool on)
 		break;
 	default:
 		return;
-	};
+	}
 
 	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
 }
@@ -237,7 +237,7 @@ static void exynos4x12_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
 		rstbits =	EXYNOS_4x12_URSTCON_HSIC1 |
 				EXYNOS_4x12_URSTCON_HOST_LINK_P1;
 		break;
-	};
+	}
 
 	if (on) {
 		pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR);
diff --git a/drivers/phy/phy-exynos5250-usb2.c b/drivers/phy/phy-exynos5250-usb2.c
index 2ed1735a076a..aad806272305 100644
--- a/drivers/phy/phy-exynos5250-usb2.c
+++ b/drivers/phy/phy-exynos5250-usb2.c
@@ -192,7 +192,7 @@ static void exynos5250_isol(struct samsung_usb2_phy_instance *inst, bool on)
 		break;
 	default:
 		return;
-	};
+	}
 
 	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
 }
diff --git a/drivers/phy/phy-meson8b-usb2.c b/drivers/phy/phy-meson8b-usb2.c
new file mode 100644
index 000000000000..33c9f4ba157d
--- /dev/null
+++ b/drivers/phy/phy-meson8b-usb2.c
@@ -0,0 +1,286 @@
+/*
+ * Meson8b and GXBB USB2 PHY driver
+ *
+ * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/usb/of.h>
+
+#define REG_CONFIG					0x00
+	#define REG_CONFIG_CLK_EN			BIT(0)
+	#define REG_CONFIG_CLK_SEL_MASK			GENMASK(3, 1)
+	#define REG_CONFIG_CLK_DIV_MASK			GENMASK(10, 4)
+	#define REG_CONFIG_CLK_32k_ALTSEL		BIT(15)
+	#define REG_CONFIG_TEST_TRIG			BIT(31)
+
+#define REG_CTRL					0x04
+	#define REG_CTRL_SOFT_PRST			BIT(0)
+	#define REG_CTRL_SOFT_HRESET			BIT(1)
+	#define REG_CTRL_SS_SCALEDOWN_MODE_MASK		GENMASK(3, 2)
+	#define REG_CTRL_CLK_DET_RST			BIT(4)
+	#define REG_CTRL_INTR_SEL			BIT(5)
+	#define REG_CTRL_CLK_DETECTED			BIT(8)
+	#define REG_CTRL_SOF_SENT_RCVD_TGL		BIT(9)
+	#define REG_CTRL_SOF_TOGGLE_OUT			BIT(10)
+	#define REG_CTRL_POWER_ON_RESET			BIT(15)
+	#define REG_CTRL_SLEEPM				BIT(16)
+	#define REG_CTRL_TX_BITSTUFF_ENN_H		BIT(17)
+	#define REG_CTRL_TX_BITSTUFF_ENN		BIT(18)
+	#define REG_CTRL_COMMON_ON			BIT(19)
+	#define REG_CTRL_REF_CLK_SEL_MASK		GENMASK(21, 20)
+	#define REG_CTRL_REF_CLK_SEL_SHIFT		20
+	#define REG_CTRL_FSEL_MASK			GENMASK(24, 22)
+	#define REG_CTRL_FSEL_SHIFT			22
+	#define REG_CTRL_PORT_RESET			BIT(25)
+	#define REG_CTRL_THREAD_ID_MASK			GENMASK(31, 26)
+
+#define REG_ENDP_INTR					0x08
+
+/* bits [31:26], [24:21] and [15:3] seem to be read-only */
+#define REG_ADP_BC					0x0c
+	#define REG_ADP_BC_VBUS_VLD_EXT_SEL		BIT(0)
+	#define REG_ADP_BC_VBUS_VLD_EXT			BIT(1)
+	#define REG_ADP_BC_OTG_DISABLE			BIT(2)
+	#define REG_ADP_BC_ID_PULLUP			BIT(3)
+	#define REG_ADP_BC_DRV_VBUS			BIT(4)
+	#define REG_ADP_BC_ADP_PRB_EN			BIT(5)
+	#define REG_ADP_BC_ADP_DISCHARGE		BIT(6)
+	#define REG_ADP_BC_ADP_CHARGE			BIT(7)
+	#define REG_ADP_BC_SESS_END			BIT(8)
+	#define REG_ADP_BC_DEVICE_SESS_VLD		BIT(9)
+	#define REG_ADP_BC_B_VALID			BIT(10)
+	#define REG_ADP_BC_A_VALID			BIT(11)
+	#define REG_ADP_BC_ID_DIG			BIT(12)
+	#define REG_ADP_BC_VBUS_VALID			BIT(13)
+	#define REG_ADP_BC_ADP_PROBE			BIT(14)
+	#define REG_ADP_BC_ADP_SENSE			BIT(15)
+	#define REG_ADP_BC_ACA_ENABLE			BIT(16)
+	#define REG_ADP_BC_DCD_ENABLE			BIT(17)
+	#define REG_ADP_BC_VDAT_DET_EN_B		BIT(18)
+	#define REG_ADP_BC_VDAT_SRC_EN_B		BIT(19)
+	#define REG_ADP_BC_CHARGE_SEL			BIT(20)
+	#define REG_ADP_BC_CHARGE_DETECT		BIT(21)
+	#define REG_ADP_BC_ACA_PIN_RANGE_C		BIT(22)
+	#define REG_ADP_BC_ACA_PIN_RANGE_B		BIT(23)
+	#define REG_ADP_BC_ACA_PIN_RANGE_A		BIT(24)
+	#define REG_ADP_BC_ACA_PIN_GND			BIT(25)
+	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
+
+#define REG_DBG_UART					0x14
+
+#define REG_TEST					0x18
+	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
+	#define REG_TEST_EN_MASK			GENMASK(7, 4)
+	#define REG_TEST_ADDR_MASK			GENMASK(11, 8)
+	#define REG_TEST_DATA_OUT_SEL			BIT(12)
+	#define REG_TEST_CLK				BIT(13)
+	#define REG_TEST_VA_TEST_EN_B_MASK		GENMASK(15, 14)
+	#define REG_TEST_DATA_OUT_MASK			GENMASK(19, 16)
+	#define REG_TEST_DISABLE_ID_PULLUP		BIT(20)
+
+#define REG_TUNE					0x1c
+	#define REG_TUNE_TX_RES_TUNE_MASK		GENMASK(1, 0)
+	#define REG_TUNE_TX_HSXV_TUNE_MASK		GENMASK(3, 2)
+	#define REG_TUNE_TX_VREF_TUNE_MASK		GENMASK(7, 4)
+	#define REG_TUNE_TX_RISE_TUNE_MASK		GENMASK(9, 8)
+	#define REG_TUNE_TX_PREEMP_PULSE_TUNE		BIT(10)
+	#define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK	GENMASK(12, 11)
+	#define REG_TUNE_TX_FSLS_TUNE_MASK		GENMASK(16, 13)
+	#define REG_TUNE_SQRX_TUNE_MASK			GENMASK(19, 17)
+	#define REG_TUNE_OTG_TUNE			GENMASK(22, 20)
+	#define REG_TUNE_COMP_DIS_TUNE			GENMASK(25, 23)
+	#define REG_TUNE_HOST_DM_PULLDOWN		BIT(26)
+	#define REG_TUNE_HOST_DP_PULLDOWN		BIT(27)
+
+#define RESET_COMPLETE_TIME				500
+#define ACA_ENABLE_COMPLETE_TIME			50
+
+struct phy_meson8b_usb2_priv {
+	void __iomem		*regs;
+	enum usb_dr_mode	dr_mode;
+	struct clk		*clk_usb_general;
+	struct clk		*clk_usb;
+	struct reset_control	*reset;
+};
+
+static u32 phy_meson8b_usb2_read(struct phy_meson8b_usb2_priv *phy_priv,
+				 u32 reg)
+{
+	return readl(phy_priv->regs + reg);
+}
+
+static void phy_meson8b_usb2_mask_bits(struct phy_meson8b_usb2_priv *phy_priv,
+				       u32 reg, u32 mask, u32 value)
+{
+	u32 data;
+
+	data = phy_meson8b_usb2_read(phy_priv, reg);
+	data &= ~mask;
+	data |= (value & mask);
+
+	writel(data, phy_priv->regs + reg);
+}
+
+static int phy_meson8b_usb2_power_on(struct phy *phy)
+{
+	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
+	int ret;
+
+	if (!IS_ERR_OR_NULL(priv->reset)) {
+		ret = reset_control_reset(priv->reset);
+		if (ret) {
+			dev_err(&phy->dev, "Failed to trigger USB reset\n");
+			return ret;
+		}
+	}
+
+	ret = clk_prepare_enable(priv->clk_usb_general);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to enable USB general clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(priv->clk_usb);
+	if (ret) {
+		dev_err(&phy->dev, "Failed to enable USB DDR clock\n");
+		clk_disable_unprepare(priv->clk_usb_general);
+		return ret;
+	}
+
+	phy_meson8b_usb2_mask_bits(priv, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL,
+				   REG_CONFIG_CLK_32k_ALTSEL);
+
+	phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK,
+				   0x2 << REG_CTRL_REF_CLK_SEL_SHIFT);
+
+	phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_FSEL_MASK,
+				   0x5 << REG_CTRL_FSEL_SHIFT);
+
+	/* reset the PHY */
+	phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET,
+				   REG_CTRL_POWER_ON_RESET);
+	udelay(RESET_COMPLETE_TIME);
+	phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0);
+	udelay(RESET_COMPLETE_TIME);
+
+	phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
+				   REG_CTRL_SOF_TOGGLE_OUT);
+
+	if (priv->dr_mode == USB_DR_MODE_HOST) {
+		phy_meson8b_usb2_mask_bits(priv, REG_ADP_BC,
+					   REG_ADP_BC_ACA_ENABLE,
+					   REG_ADP_BC_ACA_ENABLE);
+
+		udelay(ACA_ENABLE_COMPLETE_TIME);
+
+		if (phy_meson8b_usb2_read(priv, REG_ADP_BC) &
+			REG_ADP_BC_ACA_PIN_FLOAT) {
+			dev_warn(&phy->dev, "USB ID detect failed!\n");
+			clk_disable_unprepare(priv->clk_usb);
+			clk_disable_unprepare(priv->clk_usb_general);
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int phy_meson8b_usb2_power_off(struct phy *phy)
+{
+	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
+
+	clk_disable_unprepare(priv->clk_usb);
+	clk_disable_unprepare(priv->clk_usb_general);
+
+	return 0;
+}
+
+static const struct phy_ops phy_meson8b_usb2_ops = {
+	.power_on	= phy_meson8b_usb2_power_on,
+	.power_off	= phy_meson8b_usb2_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int phy_meson8b_usb2_probe(struct platform_device *pdev)
+{
+	struct phy_meson8b_usb2_priv *priv;
+	struct resource *res;
+	struct phy *phy;
+	struct phy_provider *phy_provider;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->regs))
+		return PTR_ERR(priv->regs);
+
+	priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general");
+	if (IS_ERR(priv->clk_usb_general))
+		return PTR_ERR(priv->clk_usb_general);
+
+	priv->clk_usb = devm_clk_get(&pdev->dev, "usb");
+	if (IS_ERR(priv->clk_usb))
+		return PTR_ERR(priv->clk_usb);
+
+	priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL);
+	if (PTR_ERR(priv->reset) == -EPROBE_DEFER)
+		return PTR_ERR(priv->reset);
+
+	priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1);
+	if (priv->dr_mode == USB_DR_MODE_UNKNOWN) {
+		dev_err(&pdev->dev,
+			"missing dual role configuration of the controller\n");
+		return -EINVAL;
+	}
+
+	phy = devm_phy_create(&pdev->dev, NULL, &phy_meson8b_usb2_ops);
+	if (IS_ERR(phy)) {
+		dev_err(&pdev->dev, "failed to create PHY\n");
+		return PTR_ERR(phy);
+	}
+
+	phy_set_drvdata(phy, priv);
+
+	phy_provider =
+		devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id phy_meson8b_usb2_of_match[] = {
+	{ .compatible = "amlogic,meson8b-usb2-phy", },
+	{ .compatible = "amlogic,meson-gxbb-usb2-phy", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, phy_meson8b_usb2_of_match);
+
+static struct platform_driver phy_meson8b_usb2_driver = {
+	.probe	= phy_meson8b_usb2_probe,
+	.driver	= {
+		.name		= "phy-meson-usb2",
+		.of_match_table	= phy_meson8b_usb2_of_match,
+	},
+};
+module_platform_driver(phy_meson8b_usb2_driver);
+
+MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>");
+MODULE_DESCRIPTION("Meson8b and GXBB USB2 PHY driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/phy-miphy365x.c b/drivers/phy/phy-miphy365x.c
deleted file mode 100644
index e661f3b36eaa..000000000000
--- a/drivers/phy/phy-miphy365x.c
+++ /dev/null
@@ -1,625 +0,0 @@
-/*
- * Copyright (C) 2014 STMicroelectronics – All Rights Reserved
- *
- * STMicroelectronics PHY driver MiPHY365 (for SoC STiH416).
- *
- * Authors: Alexandre Torgue <alexandre.torgue@st.com>
- *          Lee Jones <lee.jones@linaro.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2, as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/of_platform.h>
-#include <linux/of_address.h>
-#include <linux/clk.h>
-#include <linux/phy/phy.h>
-#include <linux/delay.h>
-#include <linux/mfd/syscon.h>
-#include <linux/regmap.h>
-
-#include <dt-bindings/phy/phy.h>
-
-#define HFC_TIMEOUT		100
-
-#define SYSCFG_SELECT_SATA_MASK	BIT(1)
-#define SYSCFG_SELECT_SATA_POS	1
-
-/* MiPHY365x register definitions */
-#define RESET_REG		0x00
-#define RST_PLL			BIT(1)
-#define RST_PLL_CAL		BIT(2)
-#define RST_RX			BIT(4)
-#define RST_MACRO		BIT(7)
-
-#define STATUS_REG		0x01
-#define IDLL_RDY		BIT(0)
-#define PLL_RDY			BIT(1)
-#define DES_BIT_LOCK		BIT(2)
-#define DES_SYMBOL_LOCK		BIT(3)
-
-#define CTRL_REG		0x02
-#define TERM_EN			BIT(0)
-#define PCI_EN			BIT(2)
-#define DES_BIT_LOCK_EN		BIT(3)
-#define TX_POL			BIT(5)
-
-#define INT_CTRL_REG		0x03
-
-#define BOUNDARY1_REG		0x10
-#define SPDSEL_SEL		BIT(0)
-
-#define BOUNDARY3_REG		0x12
-#define TX_SPDSEL_GEN1_VAL	0
-#define TX_SPDSEL_GEN2_VAL	0x01
-#define TX_SPDSEL_GEN3_VAL	0x02
-#define RX_SPDSEL_GEN1_VAL	0
-#define RX_SPDSEL_GEN2_VAL	(0x01 << 3)
-#define RX_SPDSEL_GEN3_VAL	(0x02 << 3)
-
-#define PCIE_REG		0x16
-
-#define BUF_SEL_REG		0x20
-#define CONF_GEN_SEL_GEN3	0x02
-#define CONF_GEN_SEL_GEN2	0x01
-#define PD_VDDTFILTER		BIT(4)
-
-#define TXBUF1_REG		0x21
-#define SWING_VAL		0x04
-#define SWING_VAL_GEN1		0x03
-#define PREEMPH_VAL		(0x3 << 5)
-
-#define TXBUF2_REG		0x22
-#define TXSLEW_VAL		0x2
-#define TXSLEW_VAL_GEN1		0x4
-
-#define RXBUF_OFFSET_CTRL_REG	0x23
-
-#define RXBUF_REG		0x25
-#define SDTHRES_VAL		0x01
-#define EQ_ON3			(0x03 << 4)
-#define EQ_ON1			(0x01 << 4)
-
-#define COMP_CTRL1_REG		0x40
-#define START_COMSR		BIT(0)
-#define START_COMZC		BIT(1)
-#define COMSR_DONE		BIT(2)
-#define COMZC_DONE		BIT(3)
-#define COMP_AUTO_LOAD		BIT(4)
-
-#define COMP_CTRL2_REG		0x41
-#define COMP_2MHZ_RAT_GEN1	0x1e
-#define COMP_2MHZ_RAT		0xf
-
-#define COMP_CTRL3_REG		0x42
-#define COMSR_COMP_REF		0x33
-
-#define COMP_IDLL_REG		0x47
-#define COMZC_IDLL		0x2a
-
-#define PLL_CTRL1_REG		0x50
-#define PLL_START_CAL		BIT(0)
-#define BUF_EN			BIT(2)
-#define SYNCHRO_TX		BIT(3)
-#define SSC_EN			BIT(6)
-#define CONFIG_PLL		BIT(7)
-
-#define PLL_CTRL2_REG		0x51
-#define BYPASS_PLL_CAL		BIT(1)
-
-#define PLL_RAT_REG		0x52
-
-#define PLL_SSC_STEP_MSB_REG	0x56
-#define PLL_SSC_STEP_MSB_VAL	0x03
-
-#define PLL_SSC_STEP_LSB_REG	0x57
-#define PLL_SSC_STEP_LSB_VAL	0x63
-
-#define PLL_SSC_PER_MSB_REG	0x58
-#define PLL_SSC_PER_MSB_VAL	0
-
-#define PLL_SSC_PER_LSB_REG	0x59
-#define PLL_SSC_PER_LSB_VAL	0xf1
-
-#define IDLL_TEST_REG		0x72
-#define START_CLK_HF		BIT(6)
-
-#define DES_BITLOCK_REG		0x86
-#define BIT_LOCK_LEVEL		0x01
-#define BIT_LOCK_CNT_512	(0x03 << 5)
-
-struct miphy365x_phy {
-	struct phy *phy;
-	void __iomem *base;
-	bool pcie_tx_pol_inv;
-	bool sata_tx_pol_inv;
-	u32 sata_gen;
-	u32 ctrlreg;
-	u8 type;
-};
-
-struct miphy365x_dev {
-	struct device *dev;
-	struct regmap *regmap;
-	struct mutex miphy_mutex;
-	struct miphy365x_phy **phys;
-	int nphys;
-};
-
-/*
- * These values are represented in Device tree. They are considered to be ABI
- * and although they can be extended any existing values must not change.
- */
-enum miphy_sata_gen {
-	SATA_GEN1 = 1,
-	SATA_GEN2,
-	SATA_GEN3
-};
-
-static u8 rx_tx_spd[] = {
-	0, /* GEN0 doesn't exist. */
-	TX_SPDSEL_GEN1_VAL | RX_SPDSEL_GEN1_VAL,
-	TX_SPDSEL_GEN2_VAL | RX_SPDSEL_GEN2_VAL,
-	TX_SPDSEL_GEN3_VAL | RX_SPDSEL_GEN3_VAL
-};
-
-/*
- * This function selects the system configuration,
- * either two SATA, one SATA and one PCIe, or two PCIe lanes.
- */
-static int miphy365x_set_path(struct miphy365x_phy *miphy_phy,
-			      struct miphy365x_dev *miphy_dev)
-{
-	bool sata = (miphy_phy->type == PHY_TYPE_SATA);
-
-	return regmap_update_bits(miphy_dev->regmap,
-				  miphy_phy->ctrlreg,
-				  SYSCFG_SELECT_SATA_MASK,
-				  sata << SYSCFG_SELECT_SATA_POS);
-}
-
-static int miphy365x_init_pcie_port(struct miphy365x_phy *miphy_phy,
-				    struct miphy365x_dev *miphy_dev)
-{
-	u8 val;
-
-	if (miphy_phy->pcie_tx_pol_inv) {
-		/* Invert Tx polarity and clear pci_txdetect_pol bit */
-		val = TERM_EN | PCI_EN | DES_BIT_LOCK_EN | TX_POL;
-		writeb_relaxed(val, miphy_phy->base + CTRL_REG);
-		writeb_relaxed(0x00, miphy_phy->base + PCIE_REG);
-	}
-
-	return 0;
-}
-
-static inline int miphy365x_hfc_not_rdy(struct miphy365x_phy *miphy_phy,
-					struct miphy365x_dev *miphy_dev)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
-	u8 mask = IDLL_RDY | PLL_RDY;
-	u8 regval;
-
-	do {
-		regval = readb_relaxed(miphy_phy->base + STATUS_REG);
-		if (!(regval & mask))
-			return 0;
-
-		usleep_range(2000, 2500);
-	} while (time_before(jiffies, timeout));
-
-	dev_err(miphy_dev->dev, "HFC ready timeout!\n");
-	return -EBUSY;
-}
-
-static inline int miphy365x_rdy(struct miphy365x_phy *miphy_phy,
-				struct miphy365x_dev *miphy_dev)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(HFC_TIMEOUT);
-	u8 mask = IDLL_RDY | PLL_RDY;
-	u8 regval;
-
-	do {
-		regval = readb_relaxed(miphy_phy->base + STATUS_REG);
-		if ((regval & mask) == mask)
-			return 0;
-
-		usleep_range(2000, 2500);
-	} while (time_before(jiffies, timeout));
-
-	dev_err(miphy_dev->dev, "PHY not ready timeout!\n");
-	return -EBUSY;
-}
-
-static inline void miphy365x_set_comp(struct miphy365x_phy *miphy_phy,
-				      struct miphy365x_dev *miphy_dev)
-{
-	u8 val, mask;
-
-	if (miphy_phy->sata_gen == SATA_GEN1)
-		writeb_relaxed(COMP_2MHZ_RAT_GEN1,
-			       miphy_phy->base + COMP_CTRL2_REG);
-	else
-		writeb_relaxed(COMP_2MHZ_RAT,
-			       miphy_phy->base + COMP_CTRL2_REG);
-
-	if (miphy_phy->sata_gen != SATA_GEN3) {
-		writeb_relaxed(COMSR_COMP_REF,
-			       miphy_phy->base + COMP_CTRL3_REG);
-		/*
-		 * Force VCO current to value defined by address 0x5A
-		 * and disable PCIe100Mref bit
-		 * Enable auto load compensation for pll_i_bias
-		 */
-		writeb_relaxed(BYPASS_PLL_CAL, miphy_phy->base + PLL_CTRL2_REG);
-		writeb_relaxed(COMZC_IDLL, miphy_phy->base + COMP_IDLL_REG);
-	}
-
-	/*
-	 * Force restart compensation and enable auto load
-	 * for Comzc_Tx, Comzc_Rx and Comsr on macro
-	 */
-	val = START_COMSR | START_COMZC | COMP_AUTO_LOAD;
-	writeb_relaxed(val, miphy_phy->base + COMP_CTRL1_REG);
-
-	mask = COMSR_DONE | COMZC_DONE;
-	while ((readb_relaxed(miphy_phy->base + COMP_CTRL1_REG) & mask)	!= mask)
-		cpu_relax();
-}
-
-static inline void miphy365x_set_ssc(struct miphy365x_phy *miphy_phy,
-				     struct miphy365x_dev *miphy_dev)
-{
-	u8 val;
-
-	/*
-	 * SSC Settings. SSC will be enabled through Link
-	 * SSC Ampl. = 0.4%
-	 * SSC Freq = 31KHz
-	 */
-	writeb_relaxed(PLL_SSC_STEP_MSB_VAL,
-		       miphy_phy->base + PLL_SSC_STEP_MSB_REG);
-	writeb_relaxed(PLL_SSC_STEP_LSB_VAL,
-		       miphy_phy->base + PLL_SSC_STEP_LSB_REG);
-	writeb_relaxed(PLL_SSC_PER_MSB_VAL,
-		       miphy_phy->base + PLL_SSC_PER_MSB_REG);
-	writeb_relaxed(PLL_SSC_PER_LSB_VAL,
-		       miphy_phy->base + PLL_SSC_PER_LSB_REG);
-
-	/* SSC Settings complete */
-	if (miphy_phy->sata_gen == SATA_GEN1) {
-		val = PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
-		writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
-	} else {
-		val = SSC_EN | PLL_START_CAL | BUF_EN | SYNCHRO_TX | CONFIG_PLL;
-		writeb_relaxed(val, miphy_phy->base + PLL_CTRL1_REG);
-	}
-}
-
-static int miphy365x_init_sata_port(struct miphy365x_phy *miphy_phy,
-				    struct miphy365x_dev *miphy_dev)
-{
-	int ret;
-	u8 val;
-
-	/*
-	 * Force PHY macro reset, PLL calibration reset, PLL reset
-	 * and assert Deserializer Reset
-	 */
-	val = RST_PLL | RST_PLL_CAL | RST_RX | RST_MACRO;
-	writeb_relaxed(val, miphy_phy->base + RESET_REG);
-
-	if (miphy_phy->sata_tx_pol_inv)
-		writeb_relaxed(TX_POL, miphy_phy->base + CTRL_REG);
-
-	/*
-	 * Force macro1 to use rx_lspd, tx_lspd
-	 * Force Rx_Clock on first I-DLL phase
-	 * Force Des in HP mode on macro, rx_lspd, tx_lspd for Gen2/3
-	 */
-	write