Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "Quite a lot of core work this time around, though not 100% successful.

  We gained support for runtime mode changes thanks to David Collins and
  improved support for write only regulators (ones where we can't read
  back the configuration) from Douglas Anderson.

  There's been quite a bit of work from Linus Walleij on converting from
  specfying GPIOs by numbers to descriptors. Sadly the testing turned
  out to be less good than we had hoped and so a lot of this had to be
  reverted.

  We also have the start of updates to use coupled regulators from
  Maciej Purski, unfortunately there are further problems there so the
  last couple of patches have been reverted.

  We also have new drivers for BD71837 and SY8106A devices, SAW
  regulators on Qualcomm SPMI and dropped support for some preproduction
  chips that never made it to market from the AB8500 driver"

* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
  regulator: gpio: Revert
  ARM: pxa, regulator: fix building ezx e680
  regulator: Revert coupled regulator support again
  regulator: wm8994: Fix shared GPIOs
  regulator: max77686: Fix shared GPIOs
  regulator: bd71837: BD71837 PMIC regulator driver
  regulator: bd71837: Devicetree bindings for BD71837 regulators
  regulator: gpio: Get enable GPIO using GPIO descriptor
  regulator: fixed: Convert to use GPIO descriptor only
  regulator: s2mps11: Fix boot on Odroid XU3
  dt-bindings: qcom_spmi: Document SAW support
  regulator: qcom_spmi: Add support for SAW
  regulator: tps65090: Pass descriptor instead of GPIO number
  regulator: s5m8767: Pass descriptor instead of GPIO number
  regulator: pfuze100: Delete reference to ena_gpio
  regulator: max8952: Pass descriptor instead of GPIO number
  regulator: lp8788-ldo: Pass descriptor instead of GPIO number
  regulator: lm363x: Pass descriptor instead of GPIO number
  regulator: max8973: Pass descriptor instead of GPIO number
  regulator: mc13xxx-core: Switch to SPDX identifier
  ...

30 files changed, 1705 insertions, 1657 deletions

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 097f61784a7d..5dbccf5f3037 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
 	  BCM590xx PMUs. This will enable support for the software
 	  controllable LDO/Switching regulators.
 
+config REGULATOR_BD71837
+	tristate "ROHM BD71837 Power Regulator"
+	depends on MFD_BD71837
+	help
+	  This driver supports voltage regulators on ROHM BD71837 PMIC.
+	  This will enable support for the software controllable buck
+	  and LDO regulators.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called bd71837-regulator.
+
 config REGULATOR_BD9571MWV
 	tristate "ROHM BD9571MWV Regulators"
 	depends on MFD_BD9571MWV
@@ -801,6 +812,13 @@ config REGULATOR_STW481X_VMMC
 	  This driver supports the internal VMMC regulator in the STw481x
 	  PMIC chips.
 
+config REGULATOR_SY8106A
+	tristate "Silergy SY8106A regulator"
+	depends on I2C && (OF || COMPILE_TEST)
+	select REGMAP_I2C
+	help
+	  This driver supports SY8106A single output regulator.
+
 config REGULATOR_TPS51632
 	tristate "TI TPS51632 Power Regulator"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 590674fbecd7..bd818ceb7c72 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
 obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
 obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
 obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD71837) += bd71837-regulator.o
 obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
 obj-$(CONFIG_REGULATOR_DA903X)	+= da903x.o
 obj-$(CONFIG_REGULATOR_DA9052)	+= da9052-regulator.o
@@ -100,6 +101,7 @@ obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
+obj-$(CONFIG_REGULATOR_SY8106A) += sy8106a-regulator.o
 obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS62360) += tps62360-regulator.o
@@ -125,5 +127,4 @@ obj-$(CONFIG_REGULATOR_WM8350) += wm8350-regulator.o
 obj-$(CONFIG_REGULATOR_WM8400) += wm8400-regulator.o
 obj-$(CONFIG_REGULATOR_WM8994) += wm8994-regulator.o
 
-
 ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG
diff --git a/drivers/regulator/ab8500.c b/drivers/regulator/ab8500.c
index 0f97514e3474..83dba3fbfe0c 100644
--- a/drivers/regulator/ab8500.c
+++ b/drivers/regulator/ab8500.c
@@ -132,33 +132,6 @@ static const unsigned int ldo_vaux56_voltages[] = {
 	2790000,
 };
 
-static const unsigned int ldo_vaux3_ab8540_voltages[] = {
-	1200000,
-	1500000,
-	1800000,
-	2100000,
-	2500000,
-	2750000,
-	2790000,
-	2910000,
-	3050000,
-};
-
-static const unsigned int ldo_vaux56_ab8540_voltages[] = {
-	750000, 760000, 770000, 780000, 790000, 800000,
-	810000, 820000, 830000, 840000, 850000, 860000,
-	870000, 880000, 890000, 900000, 910000, 920000,
-	930000, 940000, 950000, 960000, 970000, 980000,
-	990000, 1000000, 1010000, 1020000, 1030000,
-	1040000, 1050000, 1060000, 1070000, 1080000,
-	1090000, 1100000, 1110000, 1120000, 1130000,
-	1140000, 1150000, 1160000, 1170000, 1180000,
-	1190000, 1200000, 1210000, 1220000, 1230000,
-	1240000, 1250000, 1260000, 1270000, 1280000,
-	1290000, 1300000, 1310000, 1320000, 1330000,
-	1340000, 1350000, 1360000, 1800000, 2790000,
-};
-
 static const unsigned int ldo_vintcore_voltages[] = {
 	1200000,
 	1225000,
@@ -232,8 +205,6 @@ static const unsigned int ldo_vdmic_voltages[] = {
 static DEFINE_MUTEX(shared_mode_mutex);
 static struct ab8500_shared_mode ldo_anamic1_shared;
 static struct ab8500_shared_mode ldo_anamic2_shared;
-static struct ab8500_shared_mode ab8540_ldo_anamic1_shared;
-static struct ab8500_shared_mode ab8540_ldo_anamic2_shared;
 
 static int ab8500_regulator_enable(struct regulator_dev *rdev)
 {
@@ -507,53 +478,6 @@ static int ab8500_regulator_get_voltage_sel(struct regulator_dev *rdev)
 	return (regval & info->voltage_mask) >> voltage_shift;
 }
 
-static int ab8540_aux3_regulator_get_voltage_sel(struct regulator_dev *rdev)
-{
-	int ret, voltage_shift;
-	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
-	u8 regval, regval_expand;
-
-	if (info == NULL) {
-		dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
-		return -EINVAL;
-	}
-
-	ret = abx500_get_register_interruptible(info->dev,
-			info->expand_register.voltage_bank,
-			info->expand_register.voltage_reg, &regval_expand);
-	if (ret < 0) {
-		dev_err(rdev_get_dev(rdev),
-			"couldn't read voltage expand reg for regulator\n");
-		return ret;
-	}
-
-	dev_vdbg(rdev_get_dev(rdev),
-		 "%s-get_voltage expand (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
-		 info->desc.name, info->expand_register.voltage_bank,
-		 info->expand_register.voltage_reg,
-		 info->expand_register.voltage_mask, regval_expand);
-
-	if (regval_expand & info->expand_register.voltage_mask)
-		return info->expand_register.voltage_limit;
-
-	ret = abx500_get_register_interruptible(info->dev,
-			info->voltage_bank, info->voltage_reg, &regval);
-	if (ret < 0) {
-		dev_err(rdev_get_dev(rdev),
-			"couldn't read voltage reg for regulator\n");
-		return ret;
-	}
-
-	dev_vdbg(rdev_get_dev(rdev),
-		 "%s-get_voltage (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
-		 info->desc.name, info->voltage_bank, info->voltage_reg,
-		 info->voltage_mask, regval);
-
-	voltage_shift = ffs(info->voltage_mask) - 1;
-
-	return (regval & info->voltage_mask) >> voltage_shift;
-}
-
 static int ab8500_regulator_set_voltage_sel(struct regulator_dev *rdev,
 					    unsigned selector)
 {
@@ -586,61 +510,6 @@ static int ab8500_regulator_set_voltage_sel(struct regulator_dev *rdev,
 	return ret;
 }
 
-static int ab8540_aux3_regulator_set_voltage_sel(struct regulator_dev *rdev,
-						unsigned selector)
-{
-	int ret;
-	struct ab8500_regulator_info *info = rdev_get_drvdata(rdev);
-	u8 regval, regval_expand;
-
-	if (info == NULL) {
-		dev_err(rdev_get_dev(rdev), "regulator info null pointer\n");
-		return -EINVAL;
-	}
-
-	if (selector < info->expand_register.voltage_limit) {
-		int voltage_shift = ffs(info->voltage_mask) - 1;
-
-		regval = (u8)selector << voltage_shift;
-		ret = abx500_mask_and_set_register_interruptible(info->dev,
-					info->voltage_bank, info->voltage_reg,
-					info->voltage_mask, regval);
-		if (ret < 0) {
-			dev_err(rdev_get_dev(rdev),
-				"couldn't set voltage reg for regulator\n");
-			return ret;
-		}
-
-		dev_vdbg(rdev_get_dev(rdev),
-			 "%s-set_voltage (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
-			 info->desc.name, info->voltage_bank, info->voltage_reg,
-			 info->voltage_mask, regval);
-
-		regval_expand = 0;
-	} else {
-		regval_expand = info->expand_register.voltage_mask;
-	}
-
-	ret = abx500_mask_and_set_register_interruptible(info->dev,
-				info->expand_register.voltage_bank,
-				info->expand_register.voltage_reg,
-				info->expand_register.voltage_mask,
-				regval_expand);
-	if (ret < 0) {
-		dev_err(rdev_get_dev(rdev),
-			"couldn't set expand voltage reg for regulator\n");
-		return ret;
-	}
-
-	dev_vdbg(rdev_get_dev(rdev),
-		 "%s-set_voltage expand (bank, reg, mask, value): 0x%x, 0x%x, 0x%x, 0x%x\n",
-		 info->desc.name, info->expand_register.voltage_bank,
-		 info->expand_register.voltage_reg,
-		 info->expand_register.voltage_mask, regval_expand);
-
-	return 0;
-}
-
 static struct regulator_ops ab8500_regulator_volt_mode_ops = {
 	.enable			= ab8500_regulator_enable,
 	.disable		= ab8500_regulator_disable,
@@ -653,18 +522,6 @@ static struct regulator_ops ab8500_regulator_volt_mode_ops = {
 	.list_voltage		= regulator_list_voltage_table,
 };
 
-static struct regulator_ops ab8540_aux3_regulator_volt_mode_ops = {
-	.enable		= ab8500_regulator_enable,
-	.disable	= ab8500_regulator_disable,
-	.get_optimum_mode	= ab8500_regulator_get_optimum_mode,
-	.set_mode	= ab8500_regulator_set_mode,
-	.get_mode	= ab8500_regulator_get_mode,
-	.is_enabled	= ab8500_regulator_is_enabled,
-	.get_voltage_sel = ab8540_aux3_regulator_get_voltage_sel,
-	.set_voltage_sel = ab8540_aux3_regulator_set_voltage_sel,
-	.list_voltage	= regulator_list_voltage_table,
-};
-
 static struct regulator_ops ab8500_regulator_volt_ops = {
 	.enable		= ab8500_regulator_enable,
 	.disable	= ab8500_regulator_disable,
@@ -1217,562 +1074,6 @@ static struct ab8500_regulator_info
 	},
 };
 
-/* AB9540 regulator information */
-static struct ab8500_regulator_info
-		ab9540_regulator_info[AB9540_NUM_REGULATORS] = {
-	/*
-	 * Variable Voltage Regulators
-	 *   name, min mV, max mV,
-	 *   update bank, reg, mask, enable val
-	 *   volt bank, reg, mask
-	 */
-	[AB9540_LDO_AUX1] = {
-		.desc = {
-			.name		= "LDO-AUX1",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_AUX1,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x09,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x1f,
-		.voltage_mask		= 0x0f,
-	},
-	[AB9540_LDO_AUX2] = {
-		.desc = {
-			.name		= "LDO-AUX2",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_AUX2,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x09,
-		.update_mask		= 0x0c,
-		.update_val		= 0x04,
-		.update_val_idle	= 0x0c,
-		.update_val_normal	= 0x04,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x20,
-		.voltage_mask		= 0x0f,
-	},
-	[AB9540_LDO_AUX3] = {
-		.desc = {
-			.name		= "LDO-AUX3",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_AUX3,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vaux3_voltages),
-			.volt_table	= ldo_vaux3_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x0a,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x21,
-		.voltage_mask		= 0x07,
-	},
-	[AB9540_LDO_AUX4] = {
-		.desc = {
-			.name		= "LDO-AUX4",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_AUX4,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		/* values for Vaux4Regu register */
-		.update_bank		= 0x04,
-		.update_reg		= 0x2e,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		/* values for Vaux4SEL register */
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x2f,
-		.voltage_mask		= 0x0f,
-	},
-	[AB9540_LDO_INTCORE] = {
-		.desc = {
-			.name		= "LDO-INTCORE",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_INTCORE,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vintcore_voltages),
-			.volt_table	= ldo_vintcore_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x80,
-		.update_mask		= 0x44,
-		.update_val		= 0x44,
-		.update_val_idle	= 0x44,
-		.update_val_normal	= 0x04,
-		.voltage_bank		= 0x03,
-		.voltage_reg		= 0x80,
-		.voltage_mask		= 0x38,
-	},
-
-	/*
-	 * Fixed Voltage Regulators
-	 *   name, fixed mV,
-	 *   update bank, reg, mask, enable val
-	 */
-	[AB9540_LDO_TVOUT] = {
-		.desc = {
-			.name		= "LDO-TVOUT",
-			.ops		= &ab8500_regulator_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_TVOUT,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2000000_voltage,
-			.enable_time	= 10000,
-		},
-		.load_lp_uA		= 1000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x80,
-		.update_mask		= 0x82,
-		.update_val		= 0x02,
-		.update_val_idle	= 0x82,
-		.update_val_normal	= 0x02,
-	},
-	[AB9540_LDO_USB] = {
-		.desc = {
-			.name           = "LDO-USB",
-			.ops            = &ab8500_regulator_ops,
-			.type           = REGULATOR_VOLTAGE,
-			.id             = AB9540_LDO_USB,
-			.owner          = THIS_MODULE,
-			.n_voltages     = 1,
-			.volt_table	= fixed_3300000_voltage,
-		},
-		.update_bank            = 0x03,
-		.update_reg             = 0x82,
-		.update_mask            = 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-	},
-	[AB9540_LDO_AUDIO] = {
-		.desc = {
-			.name		= "LDO-AUDIO",
-			.ops		= &ab8500_regulator_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_AUDIO,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2000000_voltage,
-		},
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x02,
-		.update_val		= 0x02,
-	},
-	[AB9540_LDO_ANAMIC1] = {
-		.desc = {
-			.name		= "LDO-ANAMIC1",
-			.ops		= &ab8500_regulator_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_ANAMIC1,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2050000_voltage,
-		},
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x08,
-		.update_val		= 0x08,
-	},
-	[AB9540_LDO_ANAMIC2] = {
-		.desc = {
-			.name		= "LDO-ANAMIC2",
-			.ops		= &ab8500_regulator_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_ANAMIC2,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2050000_voltage,
-		},
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x10,
-		.update_val		= 0x10,
-	},
-	[AB9540_LDO_DMIC] = {
-		.desc = {
-			.name		= "LDO-DMIC",
-			.ops		= &ab8500_regulator_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_DMIC,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_1800000_voltage,
-		},
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x04,
-		.update_val		= 0x04,
-	},
-
-	/*
-	 * Regulators with fixed voltage and normal/idle modes
-	 */
-	[AB9540_LDO_ANA] = {
-		.desc = {
-			.name		= "LDO-ANA",
-			.ops		= &ab8500_regulator_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB9540_LDO_ANA,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_1200000_voltage,
-		},
-		.load_lp_uA		= 1000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x06,
-		.update_mask		= 0x0c,
-		.update_val		= 0x08,
-		.update_val_idle	= 0x0c,
-		.update_val_normal	= 0x08,
-	},
-};
-
-/* AB8540 regulator information */
-static struct ab8500_regulator_info
-		ab8540_regulator_info[AB8540_NUM_REGULATORS] = {
-	/*
-	 * Variable Voltage Regulators
-	 *   name, min mV, max mV,
-	 *   update bank, reg, mask, enable val
-	 *   volt bank, reg, mask
-	 */
-	[AB8540_LDO_AUX1] = {
-		.desc = {
-			.name		= "LDO-AUX1",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX1,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x09,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x1f,
-		.voltage_mask		= 0x0f,
-	},
-	[AB8540_LDO_AUX2] = {
-		.desc = {
-			.name		= "LDO-AUX2",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX2,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x09,
-		.update_mask		= 0x0c,
-		.update_val		= 0x04,
-		.update_val_idle	= 0x0c,
-		.update_val_normal	= 0x04,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x20,
-		.voltage_mask		= 0x0f,
-	},
-	[AB8540_LDO_AUX3] = {
-		.desc = {
-			.name		= "LDO-AUX3",
-			.ops		= &ab8540_aux3_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX3,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vaux3_ab8540_voltages),
-			.volt_table	= ldo_vaux3_ab8540_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x0a,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x21,
-		.voltage_mask		= 0x07,
-		.expand_register = {
-			.voltage_limit		= 8,
-			.voltage_bank		= 0x04,
-			.voltage_reg		= 0x01,
-			.voltage_mask		= 0x10,
-		}
-	},
-	[AB8540_LDO_AUX4] = {
-		.desc = {
-			.name		= "LDO-AUX4",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX4,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vauxn_voltages),
-			.volt_table	= ldo_vauxn_voltages,
-		},
-		.load_lp_uA		= 5000,
-		/* values for Vaux4Regu register */
-		.update_bank		= 0x04,
-		.update_reg		= 0x2e,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		/* values for Vaux4SEL register */
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x2f,
-		.voltage_mask		= 0x0f,
-	},
-	[AB8540_LDO_AUX5] = {
-		.desc = {
-			.name		= "LDO-AUX5",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX5,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vaux56_ab8540_voltages),
-			.volt_table	= ldo_vaux56_ab8540_voltages,
-		},
-		.load_lp_uA		= 20000,
-		/* values for Vaux5Regu register */
-		.update_bank		= 0x04,
-		.update_reg		= 0x32,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		/* values for Vaux5SEL register */
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x33,
-		.voltage_mask		= 0x3f,
-	},
-	[AB8540_LDO_AUX6] = {
-		.desc = {
-			.name		= "LDO-AUX6",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUX6,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vaux56_ab8540_voltages),
-			.volt_table	= ldo_vaux56_ab8540_voltages,
-		},
-		.load_lp_uA		= 20000,
-		/* values for Vaux6Regu register */
-		.update_bank		= 0x04,
-		.update_reg		= 0x35,
-		.update_mask		= 0x03,
-		.update_val		= 0x01,
-		.update_val_idle	= 0x03,
-		.update_val_normal	= 0x01,
-		/* values for Vaux6SEL register */
-		.voltage_bank		= 0x04,
-		.voltage_reg		= 0x36,
-		.voltage_mask		= 0x3f,
-	},
-	[AB8540_LDO_INTCORE] = {
-		.desc = {
-			.name		= "LDO-INTCORE",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_INTCORE,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vintcore_voltages),
-			.volt_table	= ldo_vintcore_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x80,
-		.update_mask		= 0x44,
-		.update_val		= 0x44,
-		.update_val_idle	= 0x44,
-		.update_val_normal	= 0x04,
-		.voltage_bank		= 0x03,
-		.voltage_reg		= 0x80,
-		.voltage_mask		= 0x38,
-	},
-
-	/*
-	 * Fixed Voltage Regulators
-	 *   name, fixed mV,
-	 *   update bank, reg, mask, enable val
-	 */
-	[AB8540_LDO_TVOUT] = {
-		.desc = {
-			.name		= "LDO-TVOUT",
-			.ops		= &ab8500_regulator_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_TVOUT,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table     = fixed_2000000_voltage,
-			.enable_time	= 10000,
-		},
-		.load_lp_uA		= 1000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x80,
-		.update_mask		= 0x82,
-		.update_val		= 0x02,
-		.update_val_idle	= 0x82,
-		.update_val_normal	= 0x02,
-	},
-	[AB8540_LDO_AUDIO] = {
-		.desc = {
-			.name		= "LDO-AUDIO",
-			.ops		= &ab8500_regulator_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_AUDIO,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2000000_voltage,
-		},
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x02,
-		.update_val		= 0x02,
-	},
-	[AB8540_LDO_ANAMIC1] = {
-		.desc = {
-			.name		= "LDO-ANAMIC1",
-			.ops		= &ab8500_regulator_anamic_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_ANAMIC1,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2050000_voltage,
-		},
-		.shared_mode		= &ab8540_ldo_anamic1_shared,
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x08,
-		.update_val		= 0x08,
-		.mode_bank		= 0x03,
-		.mode_reg		= 0x83,
-		.mode_mask		= 0x20,
-		.mode_val_idle		= 0x20,
-		.mode_val_normal	= 0x00,
-	},
-	[AB8540_LDO_ANAMIC2] = {
-		.desc = {
-			.name		= "LDO-ANAMIC2",
-			.ops		= &ab8500_regulator_anamic_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_ANAMIC2,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table	= fixed_2050000_voltage,
-		},
-		.shared_mode		= &ab8540_ldo_anamic2_shared,
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x10,
-		.update_val		= 0x10,
-		.mode_bank		= 0x03,
-		.mode_reg		= 0x83,
-		.mode_mask		= 0x20,
-		.mode_val_idle		= 0x20,
-		.mode_val_normal	= 0x00,
-	},
-	[AB8540_LDO_DMIC] = {
-		.desc = {
-			.name		= "LDO-DMIC",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_DMIC,
-			.owner		= THIS_MODULE,
-			.n_voltages	= ARRAY_SIZE(ldo_vdmic_voltages),
-			.volt_table	= ldo_vdmic_voltages,
-		},
-		.load_lp_uA		= 1000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x83,
-		.update_mask		= 0x04,
-		.update_val		= 0x04,
-		.voltage_bank		= 0x03,
-		.voltage_reg		= 0x83,
-		.voltage_mask		= 0xc0,
-	},
-
-	/*
-	 * Regulators with fixed voltage and normal/idle modes
-	 */
-	[AB8540_LDO_ANA] = {
-		.desc = {
-			.name		= "LDO-ANA",
-			.ops		= &ab8500_regulator_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_ANA,
-			.owner		= THIS_MODULE,
-			.n_voltages	= 1,
-			.volt_table     = fixed_1200000_voltage,
-		},
-		.load_lp_uA		= 1000,
-		.update_bank		= 0x04,
-		.update_reg		= 0x06,
-		.update_mask		= 0x0c,
-		.update_val		= 0x04,
-		.update_val_idle	= 0x0c,
-		.update_val_normal	= 0x04,
-	},
-	[AB8540_LDO_SDIO] = {
-		.desc = {
-			.name		= "LDO-SDIO",
-			.ops		= &ab8500_regulator_volt_mode_ops,
-			.type		= REGULATOR_VOLTAGE,
-			.id		= AB8540_LDO_SDIO,
-			.owner		= THIS_MODULE,
-			.n_voltages 	= ARRAY_SIZE(ldo_sdio_voltages),
-			.volt_table	= ldo_sdio_voltages,
-		},
-		.load_lp_uA		= 5000,
-		.update_bank		= 0x03,
-		.update_reg		= 0x88,
-		.update_mask		= 0x30,
-		.update_val		= 0x10,
-		.update_val_idle	= 0x30,
-		.update_val_normal	= 0x10,
-		.voltage_bank		= 0x03,
-		.voltage_reg		= 0x88,
-		.voltage_mask		= 0x07,
-	},
-};
-
 static struct ab8500_shared_mode ldo_anamic1_shared = {
 	.shared_regulator = &ab8505_regulator_info[AB8505_LDO_ANAMIC2],
 };
@@ -1781,14 +1082,6 @@ static struct ab8500_shared_mode ldo_anamic2_shared = {
 	.shared_regulator = &ab8505_regulator_info[AB8505_LDO_ANAMIC1],
 };
 
-static struct ab8500_shared_mode ab8540_ldo_anamic1_shared = {
-	.shared_regulator = &ab8540_regulator_info[AB8540_LDO_ANAMIC2],
-};
-
-static struct ab8500_shared_mode ab8540_ldo_anamic2_shared = {
-	.shared_regulator = &ab8540_regulator_info[AB8540_L