diff options
64 files changed, 2631 insertions, 694 deletions
diff --git a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt index 7ca0aa7ccc0b..428685eb2ded 100644 --- a/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/arasan,sdhci.txt @@ -15,10 +15,15 @@ Required Properties: - "arasan,sdhci-5.1": generic Arasan SDHCI 5.1 PHY - "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1": rk3399 eMMC PHY For this device it is strongly suggested to include arasan,soc-ctl-syscon. + - "xlnx,zynqmp-8.9a": ZynqMP SDHCI 8.9a PHY + For this device it is strongly suggested to include clock-output-names and + #clock-cells. - "ti,am654-sdhci-5.1", "arasan,sdhci-5.1": TI AM654 MMC PHY Note: This binding has been deprecated and moved to [5]. - "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1": Intel LGM eMMC PHY For this device it is strongly suggested to include arasan,soc-ctl-syscon. + - "intel,lgm-sdhci-5.1-sdxc", "arasan,sdhci-5.1": Intel LGM SDXC PHY + For this device it is strongly suggested to include arasan,soc-ctl-syscon. [5] Documentation/devicetree/bindings/mmc/sdhci-am654.txt @@ -38,15 +43,19 @@ Optional Properties: - clock-output-names: If specified, this will be the name of the card clock which will be exposed by this device. Required if #clock-cells is specified. - - #clock-cells: If specified this should be the value <0>. With this property - in place we will export a clock representing the Card Clock. This clock - is expected to be consumed by our PHY. You must also specify + - #clock-cells: If specified this should be the value <0> or <1>. With this + property in place we will export one or two clocks representing the Card + Clock. These clocks are expected to be consumed by our PHY. - xlnx,fails-without-test-cd: when present, the controller doesn't work when the CD line is not connected properly, and the line is not connected properly. Test mode can be used to force the controller to function. - xlnx,int-clock-stable-broken: when present, the controller always reports that the internal clock is stable even when it is not. + - xlnx,mio-bank: When specified, this will indicate the MIO bank number in + which the command and data lines are configured. If not specified, driver + will assume this as 0. + Example: sdhci@e0100000 { compatible = "arasan,sdhci-8.9a"; @@ -83,6 +92,18 @@ Example: #clock-cells = <0>; }; + sdhci: mmc@ff160000 { + compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; + interrupt-parent = <&gic>; + interrupts = <0 48 4>; + reg = <0x0 0xff160000 0x0 0x1000>; + clocks = <&clk200>, <&clk200>; + clock-names = "clk_xin", "clk_ahb"; + clock-output-names = "clk_out_sd0", "clk_in_sd0"; + #clock-cells = <1>; + clk-phase-sd-hs = <63>, <72>; + }; + emmc: sdhci@ec700000 { compatible = "intel,lgm-sdhci-5.1-emmc", "arasan,sdhci-5.1"; reg = <0xec700000 0x300>; @@ -97,3 +118,18 @@ Example: phy-names = "phy_arasan"; arasan,soc-ctl-syscon = <&sysconf>; }; + + sdxc: sdhci@ec600000 { + compatible = "arasan,sdhci-5.1", "intel,lgm-sdhci-5.1-sdxc"; + reg = <0xec600000 0x300>; + interrupt-parent = <&ioapic1>; + interrupts = <43 1>; + clocks = <&cgu0 LGM_CLK_SDIO>, <&cgu0 LGM_CLK_NGI>, + <&cgu0 LGM_GCLK_SDXC>; + clock-names = "clk_xin", "clk_ahb", "gate"; + clock-output-names = "sdxc_cardclock"; + #clock-cells = <0>; + phys = <&sdxc_phy>; + phy-names = "phy_arasan"; + arasan,soc-ctl-syscon = <&sysconf>; + }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index f707b8bee304..2fb466ca2a9d 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -18,6 +18,9 @@ Required properties: "fsl,imx6ull-usdhc" "fsl,imx7d-usdhc" "fsl,imx7ulp-usdhc" + "fsl,imx8mq-usdhc" + "fsl,imx8mm-usdhc" + "fsl,imx8mn-usdhc" "fsl,imx8qxp-usdhc" Optional properties: diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt index 8a6f87f13114..453d3b9d145d 100644 --- a/Documentation/devicetree/bindings/mmc/jz4740.txt +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -1,14 +1,16 @@ -* Ingenic JZ47xx MMC controllers +* Ingenic XBurst MMC controllers This file documents the device tree properties used for the MMC controller in -Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties -described in mmc.txt. +Ingenic JZ4740/JZ4760/JZ4780/X1000 SoCs. These are in addition to the core MMC +properties described in mmc.txt. Required properties: - compatible: Should be one of the following: - "ingenic,jz4740-mmc" for the JZ4740 - "ingenic,jz4725b-mmc" for the JZ4725B + - "ingenic,jz4760-mmc" for the JZ4760 - "ingenic,jz4780-mmc" for the JZ4780 + - "ingenic,x1000-mmc" for the X1000 - reg: Should contain the MMC controller registers location and length. - interrupts: Should contain the interrupt specifier of the MMC controller. - clocks: Clock for the MMC controller. diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml index 080754e0ef35..b130450c3b34 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -333,6 +333,19 @@ patternProperties: required: - reg + "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$": + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 2 + items: + minimum: 0 + maximum: 359 + description: + Set the clock (phase) delays which are to be configured in the + controller while switching to particular speed mode. These values + are in pair of degrees. + dependencies: cd-debounce-delay-ms: [ cd-gpios ] fixed-emmc-driver-type: [ non-removable ] @@ -351,6 +364,7 @@ examples: keep-power-in-suspend; wakeup-source; mmc-pwrseq = <&sdhci0_pwrseq>; + clk-phase-sd-hs = <63>, <72>; }; - | diff --git a/Documentation/devicetree/bindings/mmc/owl-mmc.yaml b/Documentation/devicetree/bindings/mmc/owl-mmc.yaml new file mode 100644 index 000000000000..12b40213426d --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/owl-mmc.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/owl-mmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Actions Semi Owl SoCs SD/MMC/SDIO controller + +allOf: + - $ref: "mmc-controller.yaml" + +maintainers: + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +properties: + compatible: + const: actions,owl-mmc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + + resets: + maxItems: 1 + + dmas: + maxItems: 1 + + dma-names: + const: mmc + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - dmas + - dma-names + +examples: + - | + mmc0: mmc@e0330000 { + compatible = "actions,owl-mmc"; + reg = <0x0 0xe0330000 0x0 0x4000>; + interrupts = <0 42 4>; + clocks = <&cmu 56>; + resets = <&cmu 23>; + dmas = <&dma 2>; + dma-names = "mmc"; + bus-width = <4>; + }; + +... diff --git a/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt index dd08d038a65c..bc08fc43a9be 100644 --- a/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt +++ b/Documentation/devicetree/bindings/mmc/renesas,sdhi.txt @@ -11,6 +11,7 @@ Required properties: "renesas,sdhi-r8a7744" - SDHI IP on R8A7744 SoC "renesas,sdhi-r8a7745" - SDHI IP on R8A7745 SoC "renesas,sdhi-r8a774a1" - SDHI IP on R8A774A1 SoC + "renesas,sdhi-r8a774b1" - SDHI IP on R8A774B1 SoC "renesas,sdhi-r8a774c0" - SDHI IP on R8A774C0 SoC "renesas,sdhi-r8a77470" - SDHI IP on R8A77470 SoC "renesas,sdhi-mmc-r8a77470" - SDHI/MMC IP on R8A77470 SoC diff --git a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt index 1b662d7171a0..503c6dbac1b2 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-atmel.txt @@ -9,6 +9,11 @@ Required properties: - clocks: Phandlers to the clocks. - clock-names: Must be "hclock", "multclk", "baseclk"; +Optional properties: +- microchip,sdcal-inverted: when present, polarity on the SDCAL SoC pin is + inverted. The default polarity for this signal is described in the datasheet. + For instance on SAMA5D2, the pin is usually tied to the GND with a resistor + and a capacitor (see "SDMMC I/O Calibration" chapter). Example: diff --git a/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt new file mode 100644 index 000000000000..627ee89c125b --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/sdhci-milbeaut.txt @@ -0,0 +1,30 @@ +* SOCIONEXT Milbeaut SDHCI controller + +This file documents differences between the core properties in mmc.txt +and the properties used by the sdhci_milbeaut driver. + +Required properties: +- compatible: "socionext,milbeaut-m10v-sdhci-3.0" +- clocks: Must contain an entry for each entry in clock-names. It is a + list of phandles and clock-specifier pairs. + See ../clocks/clock-bindings.txt for details. +- clock-names: Should contain the following two entries: + "iface" - clock used for sdhci interface + "core" - core clock for sdhci controller + +Optional properties: +- fujitsu,cmd-dat-delay-select: boolean property indicating that this host + requires the CMD_DAT_DELAY control to be enabled. + +Example: + sdhci3: mmc@1b010000 { + compatible = "socionext,milbeaut-m10v-sdhci-3.0"; + reg = <0x1b010000 0x10000>; + interrupts = <0 265 0x4>; + voltage-ranges = <3300 3300>; + bus-width = <4>; + clocks = <&clk 7>, <&ahb_clk>; + clock-names = "core", "iface"; + cap-sdio-irq; + fujitsu,cmd-dat-delay-select; + }; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt index bb2fcde6f7ff..f38950560982 100644 --- a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -35,3 +35,29 @@ Examples: ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ }; }; + +&mmc3 { + vmmc-supply = <&wlan_en>; + + bus-width = <4>; + non-removable; + ti,non-removable; + cap-power-off-card; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + wlan: wifi@1 { + compatible = "ti,wl1251"; + + reg = <1>; + + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ + + ti,wl1251-has-eeprom; + }; +}; diff --git a/MAINTAINERS b/MAINTAINERS index b62d025acdfa..650263142aff 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1399,6 +1399,7 @@ F: drivers/clk/actions/ F: drivers/clocksource/timer-owl* F: drivers/dma/owl-dma.c F: drivers/i2c/busses/i2c-owl.c +F: drivers/mmc/host/owl-mmc.c F: drivers/pinctrl/actions/* F: drivers/soc/actions/ F: include/dt-bindings/power/owl-* @@ -1407,6 +1408,7 @@ F: Documentation/devicetree/bindings/arm/actions.yaml F: Documentation/devicetree/bindings/clock/actions,owl-cmu.txt F: Documentation/devicetree/bindings/dma/owl-dma.txt F: Documentation/devicetree/bindings/i2c/i2c-owl.txt +F: Documentation/devicetree/bindings/mmc/owl-mmc.yaml F: Documentation/devicetree/bindings/pinctrl/actions,s900-pinctrl.txt F: Documentation/devicetree/bindings/power/actions,owl-sps.txt F: Documentation/devicetree/bindings/timer/actions,owl-timer.txt @@ -17612,10 +17614,8 @@ S: Maintained F: drivers/hwmon/vt8231.c VUB300 USB to SDIO/SD/MMC bridge chip -M: Tony Olech <tony.olech@elandigitalsystems.com> L: linux-mmc@vger.kernel.org -L: linux-usb@vger.kernel.org -S: Supported +S: Orphan F: drivers/mmc/host/vub300.c W1 DALLAS'S 1-WIRE BUS diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index ec5891718ae6..150d5be42d27 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -226,6 +226,17 @@ gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* GPIO_164 */ }; + /* wl1251 wifi+bt module */ + wlan_en: fixed-regulator-wg7210_en { + compatible = "regulator-fixed"; + regulator-name = "vwlan"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + startup-delay-us = <50000>; + enable-active-high; + gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>; + }; + /* wg7210 (wifi+bt module) 32k clock buffer */ wg7210_32k: fixed-regulator-wg7210_32k { compatible = "regulator-fixed"; @@ -522,9 +533,30 @@ /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */ }; -/* mmc3 is probed using pdata-quirks to pass wl1251 card data */ &mmc3 { - status = "disabled"; + vmmc-supply = <&wlan_en>; + + bus-width = <4>; + non-removable; + ti,non-removable; + cap-power-off-card; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins>; + + #address-cells = <1>; + #size-cells = <0>; + + wlan: wifi@1 { + compatible = "ti,wl1251"; + + reg = <1>; + + interrupt-parent = <&gpio1>; + interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* GPIO_21 */ + + ti,wl1251-has-eeprom; + }; }; /* bluetooth*/ diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 8f208197988f..1e1e86d17fc5 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -216,9 +216,6 @@ obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o # Platform specific device init code -omap-hsmmc-$(CONFIG_MMC_OMAP_HS) := hsmmc.o -obj-y += $(omap-hsmmc-m) $(omap-hsmmc-y) - obj-y += omap_phy_internal.o obj-$(CONFIG_MACH_OMAP2_TUSB6010) += usb-tusb6010.o diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index 6316da3623b3..223b37c48389 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -352,7 +352,6 @@ void omap_pcs_legacy_init(int irq, void (*rearm)(void)); struct omap_sdrc_params; extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0, struct omap_sdrc_params *sdrc_cs1); -struct omap2_hsmmc_info; extern void omap_reserve(void); struct omap_hwmod; diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c deleted file mode 100644 index 63423ea6a240..000000000000 --- a/arch/arm/mach-omap2/hsmmc.c +++ /dev/null @@ -1,171 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-only -/* - * linux/arch/arm/mach-omap2/hsmmc.c - * - * Copyright (C) 2007-2008 Texas Instruments - * Copyright (C) 2008 Nokia Corporation - * Author: Texas Instruments - */ -#include <linux/kernel.h> -#include <linux/slab.h> -#include <linux/string.h> -#include <linux/delay.h> -#include <linux/mmc/host.h> -#include <linux/platform_data/hsmmc-omap.h> - -#include "soc.h" -#include "omap_device.h" - -#include "hsmmc.h" -#include "control.h" - -#if IS_ENABLED(CONFIG_MMC_OMAP_HS) - -static u16 control_pbias_offset; -static u16 control_devconf1_offset; - -#define HSMMC_NAME_LEN 9 - -static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c, - struct omap_hsmmc_platform_data *mmc) -{ - char *hc_name; - - hc_name = kzalloc(HSMMC_NAME_LEN + 1, GFP_KERNEL); - if (!hc_name) - return -ENOMEM; - - snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i", c->mmc, 1); - mmc->name = hc_name; - mmc->caps = c->caps; - mmc->reg_offset = 0; - - return 0; -} - -static int omap_hsmmc_done; - -void omap_hsmmc_late_init(struct omap2_hsmmc_info *c) -{ - struct platform_device *pdev; - int res; - - if (omap_hsmmc_done) - return; - - omap_hsmmc_done = 1; - - for (; c->mmc; c++) { - pdev = c->pdev; - if (!pdev) - continue; - res = omap_device_register(pdev); - if (res) - pr_err("Could not late init MMC\n"); - } -} - -#define MAX_OMAP_MMC_HWMOD_NAME_LEN 16 - -static void __init omap_hsmmc_init_one(struct omap2_hsmmc_info *hsmmcinfo, - int ctrl_nr) -{ - struct omap_hwmod *oh; - struct omap_hwmod *ohs[1]; - struct omap_device *od; - struct platform_device *pdev; - char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN]; - struct omap_hsmmc_platform_data *mmc_data; - struct omap_hsmmc_dev_attr *mmc_dev_attr; - char *name; - int res; - - mmc_data = kzalloc(sizeof(*mmc_data), GFP_KERNEL); - if (!mmc_data) - return; - - res = omap_hsmmc_pdata_init(hsmmcinfo, mmc_data); - if (res < 0) - goto free_mmc; - - name = "omap_hsmmc"; - res = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN, - "mmc%d", ctrl_nr); - WARN(res >= MAX_OMAP_MMC_HWMOD_NAME_LEN, - "String buffer overflow in MMC%d device setup\n", ctrl_nr); - - oh = omap_hwmod_lookup(oh_name); - if (!oh) { - pr_err("Could not look up %s\n", oh_name); - goto free_name; - } - ohs[0] = oh; - if (oh->dev_attr != NULL) { - mmc_dev_attr = oh->dev_attr; - mmc_data->controller_flags = mmc_dev_attr->flags; - } - - pdev = platform_device_alloc(name, ctrl_nr - 1); - if (!pdev) { - pr_err("Could not allocate pdev for %s\n", name); - goto free_name; - } - dev_set_name(&pdev->dev, "%s.%d", pdev->name, pdev->id); - - od = omap_device_alloc(pdev, ohs, 1); - if (IS_ERR(od)) { - pr_err("Could not allocate od for %s\n", name); - goto put_pdev; - } - - res = platform |