diff options
127 files changed, 1022 insertions, 676 deletions
diff --git a/Documentation/driver-api/ptp.rst b/Documentation/driver-api/ptp.rst index a15192e32347..664838ae7776 100644 --- a/Documentation/driver-api/ptp.rst +++ b/Documentation/driver-api/ptp.rst @@ -23,6 +23,7 @@ PTP hardware clock infrastructure for Linux + Ancillary clock features - Time stamp external events - Period output signals configurable from user space + - Low Pass Filter (LPF) access from user space - Synchronization of the Linux system time via the PPS subsystem PTP hardware clock kernel API @@ -94,3 +95,14 @@ Supported hardware - Auxiliary Slave/Master Mode Snapshot (optional interrupt) - Target Time (optional interrupt) + + * Renesas (IDT) ClockMatrix™ + + - Up to 4 independent PHC channels + - Integrated low pass filter (LPF), access via .adjPhase (compliant to ITU-T G.8273.2) + - Programmable output periodic signals + - Programmable inputs can time stamp external triggers + - Driver and/or hardware configuration through firmware (idtcm.bin) + - LPF settings (bandwidth, phase limiting, automatic holdover, physical layer assist (per ITU-T G.8273.2)) + - Programmable output PTP clocks, any frequency up to 1GHz (to other PHY/MAC time stampers, refclk to ASSPs/SoCs/FPGAs) + - Lock to GNSS input, automatic switching between GNSS and user-space PHC control (optional) diff --git a/Documentation/networking/bareudp.rst b/Documentation/networking/bareudp.rst index 465a8b251bfe..ff406563ea88 100644 --- a/Documentation/networking/bareudp.rst +++ b/Documentation/networking/bareudp.rst @@ -26,7 +26,7 @@ Usage 1) Device creation & deletion - a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847. + a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc This creates a bareudp tunnel device which tunnels L3 traffic with ethertype 0x8847 (MPLS traffic). The destination port of the UDP header will be set to @@ -34,14 +34,21 @@ Usage b) ip link delete bareudp0 -2) Device creation with multiple proto mode enabled +2) Device creation with multiproto mode enabled -There are two ways to create a bareudp device for MPLS & IP with multiproto mode -enabled. +The multiproto mode allows bareudp tunnels to handle several protocols of the +same family. It is currently only available for IP and MPLS. This mode has to +be enabled explicitly with the "multiproto" flag. - a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847 multiproto + a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype ipv4 multiproto - b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls + For an IPv4 tunnel the multiproto mode allows the tunnel to also handle + IPv6. + + b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc multiproto + + For MPLS, the multiproto mode allows the tunnel to handle both unicast + and multicast MPLS packets. 3) Device Usage diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts index c8243da71041..eb01cc96ba7a 100644 |