diff options
124 files changed, 4775 insertions, 960 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 05496622b4ef..b24108f2a438 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -854,7 +854,7 @@ The filter can be disabled or changed to another driver later using sysfs. - drm_kms_helper.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] + drm.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>] Broken monitors, graphic adapters, KVMs and EDIDless panels may send no or incorrect EDID data sets. This parameter allows to specify an EDID data sets diff --git a/Documentation/devicetree/bindings/display/faraday,tve200.txt b/Documentation/devicetree/bindings/display/faraday,tve200.txt new file mode 100644 index 000000000000..82e3bc0b7485 --- /dev/null +++ b/Documentation/devicetree/bindings/display/faraday,tve200.txt @@ -0,0 +1,54 @@ +* Faraday TV Encoder TVE200 + +Required properties: + +- compatible: must be one of: + "faraday,tve200" + "cortina,gemini-tvc", "faraday,tve200" + +- reg: base address and size of the control registers block + +- interrupts: contains an interrupt specifier for the interrupt + line from the TVE200 + +- clock-names: should contain "PCLK" for the clock line clocking the + silicon and "TVE" for the 27MHz clock to the video driver + +- clocks: contains phandle and clock specifier pairs for the entries + in the clock-names property. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: + +- resets: contains the reset line phandle for the block + +Required sub-nodes: + +- port: describes LCD panel signals, following the common binding + for video transmitter interfaces; see + Documentation/devicetree/bindings/media/video-interfaces.txt + This port should have the properties: + reg = <0>; + It should have one endpoint connected to a remote endpoint where + the display is connected. + +Example: + +display-controller@6a000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "faraday,tve200"; + reg = <0x6a000000 0x1000>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + resets = <&syscon GEMINI_RESET_TVC>; + clocks = <&syscon GEMINI_CLK_GATE_TVC>, + <&syscon GEMINI_CLK_TVC>; + clock-names = "PCLK", "TVE"; + + port@0 { + reg = <0>; + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt new file mode 100644 index 000000000000..6862028e7b2e --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/orisetech,otm8009a.txt @@ -0,0 +1,21 @@ +Orise Tech OTM8009A 3.97" 480x800 TFT LCD panel (MIPI-DSI video mode) + +The Orise Tech OTM8009A is a 3.97" 480x800 TFT LCD panel connected using +a MIPI-DSI video interface. Its backlight is managed through the DSI link. + +Required properties: + - compatible: "orisetech,otm8009a" + - reg: the virtual channel number of a DSI peripheral + +Optional properties: + - reset-gpios: a GPIO spec for the reset pin (active low). + +Example: +&dsi { + ... + panel@0 { + compatible = "orisetech,otm8009a"; + reg = <0>; + reset-gpios = <&gpioh 7 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e63j0x03.txt new file mode 100644 index 000000000000..3f1a8392af7f --- /dev/null +++ b/Documentation/dev |