diff options
53 files changed, 1253 insertions, 358 deletions
diff --git a/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt new file mode 100644 index 000000000000..8df7d2e393d6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt @@ -0,0 +1,74 @@ +Rockchip RK3399 specific extensions to the cdn Display Port +================================ + +Required properties: +- compatible: must be "rockchip,rk3399-cdn-dp" + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + +- clock-names: from common clock binding: + Required elements: "core-clk" "pclk" "spdif" "grf" + +- resets : a list of phandle + reset specifier pairs +- reset-names : string of reset names + Required elements: "apb", "core", "dptx", "spdif" +- power-domains : power-domain property defined with a phandle + to respective power domain. +- assigned-clocks: main clock, should be <&cru SCLK_DP_CORE> +- assigned-clock-rates : the DP core clk frequency, shall be: 100000000 + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: contain a port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + contained 2 endpoints, connecting to the output of vop. + +- phys: from general PHY binding: the phandle for the PHY device. + +- extcon: extcon specifier for the Power Delivery + +- #sound-dai-cells = it must be 1 if your system is using 2 DAIs: I2S, SPDIF + +------------------------------------------------------------------------------- + +Example: + cdn_dp: dp@fec00000 { + compatible = "rockchip,rk3399-cdn-dp"; + reg = <0x0 0xfec00000 0x0 0x100000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_DP_CORE>, <&cru PCLK_DP_CTRL>, + <&cru SCLK_SPDIF_REC_DPTX>, <&cru PCLK_VIO_GRF>; + clock-names = "core-clk", "pclk", "spdif", "grf"; + assigned-clocks = <&cru SCLK_DP_CORE>; + assigned-clock-rates = <100000000>; + power-domains = <&power RK3399_PD_HDCP>; + phys = <&tcphy0_dp>, <&tcphy1_dp>; + resets = <&cru SRST_DPTX_SPDIF_REC>; + reset-names = "spdif"; + extcon = <&fusb0>, <&fusb1>; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + dp_in: port { + #address-cells = <1>; + #size-cells = <0>; + dp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_dp>; + }; + + dp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_dp>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index cd626ee1147a..b995bfee734a 100644 --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -64,6 +64,52 @@ Required properties: first port should be the input endpoint. The second should be the output, usually to an HDMI connector. +DWC HDMI TX Encoder +------------------- + +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP +with Allwinner's own PHY IP. It supports audio and video outputs and CEC. + +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the +following device-specific properties. + +Required properties: + + - compatible: value must be one of: + * "allwinner,sun8i-a83t-dw-hdmi" + - reg: base address and size of memory-mapped region + - reg-io-width: See dw_hdmi.txt. Shall be 1. + - interrupts: HDMI interrupt number + - clocks: phandles to the clocks feeding the HDMI encoder + * iahb: the HDMI bus clock + * isfr: the HDMI register clock + * tmds: TMDS clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller + - reset-names: must be "ctrl" + - phys: phandle to the DWC HDMI PHY + - phy-names: must be "phy" + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. The second should be the + output, usually to an HDMI connector. + +DWC HDMI PHY +------------ + +Required properties: + - compatible: value must be one of: + * allwinner,sun8i-a83t-hdmi-phy + - reg: base address and size of memory-mapped region + - clocks: phandles to the clocks feeding the HDMI PHY + * bus: the HDMI PHY interface clock + * mod: the HDMI PHY module clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller driving the PHY + - reset-names: must be "phy" + TV Encoder ---------- @@ -94,24 +140,26 @@ Required properties: * allwinner,sun7i-a20-tcon * allwinner,sun8i-a33-tcon * allwinner,sun8i-a83t-tcon-lcd + * allwinner,sun8i-a83t-tcon-tv * allwinner,sun8i-v3s-tcon - reg: base address and size of memory-mapped region - interrupts: interrupt associated to this IP - - clocks: phandles to the clocks feeding the TCON. Three are needed: + - clocks: phandles to the clocks feeding the TCON. - 'ahb': the interface clocks - - 'tcon-ch0': The clock driving the TCON channel 0 + - 'tcon-ch0': The clock driving the TCON channel 0, except for A83T TV TCON - resets: phandles to the reset controllers driving the encoder - "lcd": the reset line for the TCON channel 0 - clock-names: the clock names mentioned above - reset-names: the reset names mentioned above - - clock-output-names: Name of the pixel clock created + - clock-output-names: Name of the pixel clock created, if TCON supports + channel 0. - ports: A ports node with endpoint definitions as defined in Documentation/devicetree/bindings/media/video-interfaces.txt. The first port should be the input endpoint, the second one the output - The output may have multiple endpoints. The TCON has two channels, + The output may have multiple endpoints. TCON can have 1 or 2 channels, usually with the first channel being used for the panels interfaces (RGB, LVDS, etc.), and the second being used for the outputs that require another controller (TV Encoder, HDMI, etc.). The endpoints @@ -122,8 +170,8 @@ Required properties: On SoCs other than the A33 and V3s, there is one more clock required: - 'tcon-ch1': The clock driving the TCON channel 1 -On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you -need one more reset line: +When TCON support LVDS (all TCONs except TV TCON on A83T and those found +in A13, H3, H5 and V3s SoCs), you need one more reset line: - 'lvds': The reset line driving the LVDS logic And on the A23, A31, A31s and A33, you need one more clock line: @@ -226,6 +274,7 @@ supported. Required properties: - compatible: value must be one of: * allwinner,sun8i-a83t-de2-mixer-0 + * allwinner,sun8i-a83t-de2-mixer-1 * allwinner,sun8i-v3s-de2-mixer - reg: base address and size of the memory-mapped region. - clocks: phandles to the clocks feeding the mixer diff --git a/Documentation/gpu/drm-kms.rst b/Documentation/gpu/drm-kms.rst index 2dcf5b42015d..56a3780e39b8 100644 --- a/Documentation/gpu/drm-kms.rst +++ b/Documentation/gpu/drm-kms.rst @@ -547,8 +547,9 @@ Explicit Fencing Properties Existing KMS Properties ----------------------- -The following table gives description of drm properties exposed by -various modules/drivers. +The following table gives description of drm properties exposed by various +modules/drivers. Because this table is very unwieldy, do not add any new +properties here. Instead document them in a section above. .. csv-table:: :header-rows: 1 diff --git a/Documentation/gpu/kms-properties.csv b/Documentation/gpu/kms-properties.csv index 927b65e14219..6b28b014cb7d 100644 --- a/Documentation/gpu/kms-properties.csv +++ b/Documentation/gpu/kms-properties.csv @@ -1,5 +1,4 @@ Owner Module/Drivers,Group,Property Name,Type,Property Values,Object attached,Description/Restrictions -,,“scaling mode”,ENUM,"{ ""None"", ""Full"", ""Center"", ""Full aspect"" }",Connector,"Supported by: amdgpu, gma500, i915, nouveau and radeon." ,DVI-I,“subconnector”,ENUM,"{ “Unknown”, “DVI-D”, “DVI-A” }",Connector,TBD ,,“select subconnector”,ENUM,"{ “Automatic”, “DVI-D”, “DVI-A” }",Connector,TBD ,TV,“subconnector”,ENUM,"{ ""Unknown"", ""Composite"", ""SVIDEO"", ""Component"", ""SCART"" }",Connector,TBD diff --git a/Documentation/gpu/todo.rst b/Documentation/gpu/todo.rst index 1e593370f64f..1a0a413eeced 100644 --- a/Documentation/gpu/todo.rst +++ b/Documentation/gpu/todo.rst @@ -212,6 +212,16 @@ probably use drm_fb_helper_fbdev_teardown(). Contact: Maintainer of the driver you plan to convert +idr_init_base() +--------------- + +DRM core&drivers uses a lot of idr (integer lookup directories) for mapping +userspace IDs to internal objects, and in most places ID=0 means NULL and hence +is never used. Switching to idr_init_base() for these would make the idr more +efficient. + +Contact: Daniel Vetter + Core refactorings ================= diff --git a/drivers/dma-buf/sw_sync.c b/drivers/dma-buf/sw_sync.c index 7779bdbd18d1..3d78ca89a605 100644 --- a/drivers/dma-buf/sw_sync.c +++ b/drivers/dma-buf/sw_sync.c @@ -235,10 +235,10 @@ static void sync_timeline_signal(struct sync_timeline *obj, unsigned int inc) /** * sync_pt_create() - creates a sync pt - * @parent: fence's parent sync_timeline - * @inc: value of the fence + * @obj: parent sync_timeline + * @value: value of the fence * - * Creates a new sync_pt as a child of @parent. @size bytes will be + * Creates a new sync_pt (fence) as a child of @parent. @size bytes will be * allocated allowing for implementation specific data to be kept after * the generic sync_timeline struct. Returns the sync_pt object or * NULL in case of error. diff --git a/drivers/gpu/drm/bochs/bochs_mm.c b/drivers/gpu/drm/bochs/bochs_mm.c index 704e879711e4..b1d5aee46316 100644 --- a/drivers/gpu/drm/bochs/bochs_mm.c +++ b/drivers/gpu/drm/bochs/bochs_mm.c @@ -194,7 +194,7 @@ static struct ttm_tt *bochs_ttm_tt_create(struct ttm_bo_device *bdev, return tt; } -struct ttm_bo_driver bochs_bo_driver = { +static struct ttm_bo_driver bochs_bo_driver = { .ttm_tt_create = bochs_ttm_tt_create, .ttm_tt_populate = ttm_pool_populate, .ttm_tt_unpopulate = ttm_pool_unpopulate, diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index a38db40ce990..f9802399cc0d 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -1037,19 +1037,21 @@ static void dw_hdmi_phy_enable_svsret(struct dw_hdmi *hdmi, u8 enable) HDMI_PHY_CONF0_SVSRET_MASK); } -static void dw_hdmi_phy_gen2_pddq(struct dw_hdmi *hdmi, u8 enable) +void dw_hdmi_phy_gen2_pddq(struct dw_hdmi *hdmi, u8 enable) { hdmi_mask_writeb(hdmi, enable, HDMI_PHY_CONF0, HDMI_PHY_CONF0_GEN2_PDDQ_OFFSET, HDMI_PHY_CONF0_GEN2_PDDQ_MASK); } +EXPORT_SYMBOL_GPL(dw_hdmi_phy_gen2_pddq); -static void dw_hdmi_phy_gen2_txpwron(struct dw_hdmi *hdmi, u8 enable) +void dw_hdmi_phy_gen2_txpwron(struct dw_hdmi *hdmi, u8 enable) { hdmi_mask_writeb(hdmi, enable, HDMI_PHY_CONF0, HDMI_PHY_CONF0_GEN2_TXPWRON_OFFSET, HDMI_PHY_CONF0_GEN2_TXPWRON_MASK); } +EXPORT_SYMBOL_GPL(dw_hdmi_phy_gen2_txpwron); static void dw_hdmi_phy_sel_data_en_pol(struct dw_hdmi *hdmi, u8 enable) { @@ -1065,6 +1067,22 @@ static void dw_hdmi_phy_sel_interface_control(struct dw_hdmi *hdmi, u8 enable) HDMI_PHY_CONF0_SELDIPIF_MASK); } +void dw_hdmi_phy_reset(struct dw_hdmi *hdmi) +{ + /* PHY reset. The reset signal is active high on Gen2 PHYs. */ + hdmi_writeb(hdmi, HDMI_MC_PHYRSTZ_PHYRSTZ, HDMI_MC_PHYRSTZ); + hdmi_writeb(hdmi, 0, HDMI_MC_PHYRSTZ); +} +EXPORT_SYMBOL_GPL(dw_hdmi_phy_reset); + +void dw_hdmi_phy_i2c_set_addr(struct dw_hdmi *hdmi, u8 address) +{ + hdmi_phy_test_clear(hdmi, 1); + hdmi_writeb(hdmi, address, HDMI_PHY_I2CM_SLAVE_ADDR); + hdmi_phy_test_clear(hdmi, 0); +} +EXPORT_SYMBOL_GPL(dw_hdmi_phy_i2c_set_addr); + static void dw_hdmi_phy_power_off(struct dw_hdmi *hdmi) { const struct dw_hdmi_phy_data *phy = hdmi->phy.data; @@ -1203,16 +1221,11 @@ static int hdmi_phy_configure(struct dw_hdmi *hdmi) if (phy->has_svsret) dw_hdmi_phy_enable_svsret(hdmi, 1); - /* PHY reset. The reset signal is active high on Gen2 PHYs. */ - hdmi_writeb(hdmi, HDMI_MC_PHYRSTZ_PHYRSTZ, HDMI_MC_PHYRSTZ); - hdmi_writeb(hdmi, 0, HDMI_MC_PHYRSTZ); + dw_hdmi_phy_reset(hdmi); hdmi_writeb(hdmi, HDMI_MC_HEACPHY_RST_ASSERT, HDMI_MC_HEACPHY_RST); - hdmi_phy_test_clear(hdmi, 1); - hdmi_writeb(hdmi, HDMI_PHY_I2CM_SLAVE_ADDR_PHY_GEN2, - HDMI_PHY_I2CM_SLAVE_ADDR); - hdmi_phy_test_clear(hdmi, 0); + dw_hdmi_phy_i2c_set_addr(hdmi, HDMI_PHY_I2CM_SLAVE_ADDR_PHY_GEN2); /* Write to the PHY as configured by the platform */ if (pdata->configure_phy) @@ -1251,15 +1264,16 @@ static void dw_hdmi_phy_disable(struct dw_hdmi *hdmi, void *data) dw_hdmi_phy_power_off(hdmi); } -static enum drm_connector_status dw_hdmi_phy_read_hpd(struct dw_hdmi *hdmi, - void *data) +enum drm_connector_status dw_hdmi_phy_read_hpd(struct dw_hdmi *hdmi, + void *data) { return hdmi_readb(hdmi, HDMI_PHY_STAT0) & HDMI_PHY_HPD ? connector_status_connected : connector_status_disconnected; } +EXPORT_SYMBOL_GPL(dw_hdmi_phy_read_hpd); -static void dw_hdmi_phy_update_hpd(struct dw_hdmi *hdmi, void *data, - bool force, bool disabled, bool rxsense) +void dw_hdmi_phy_update_hpd(struct dw_hdmi *hdmi, void *data, + bool force, bool disabled, bool rxsense) { u8 old_mask = hdmi->phy_mask; @@ -1271,8 +1285,9 @@ static void dw_hdmi_phy_update_hpd(struct dw_hdmi *hdmi, void *data, if (old_mask != hdmi->phy_mask) hdmi_writeb(hdmi, hdmi->phy_mask, HDMI_PHY_MASK0); } +EXPORT_SYMBOL_GPL(dw_hdmi_phy_update_hpd); -static void dw_hdmi_phy_setup_hpd(struct dw_hdmi *hdmi, void *data) +void dw_hdmi_phy_setup_hpd(struct dw_hdmi *hdmi, void *data) { /* * Configure the PHY RX SENSE and HPD interrupts polarities and clear @@ -1291,6 +1306,7 @@ static void dw_hdmi_phy_setup_hpd(struct dw_hdmi *hdmi, void *data) hdmi_writeb(hdmi, ~(HDMI_IH_PHY_STAT0_HPD | HDMI_IH_PHY_STAT0_RX_SENSE), HDMI_IH_MUTE_PHY_STAT0); } +EXPORT_SYMBOL_GPL(dw_hdmi_phy_setup_hpd); static const struct dw_hdmi_phy_ops dw_hdmi_synopsys_phy_ops = { .init = dw_hdmi_phy_init, @@ -1634,9 +1650,10 @@ static void dw_hdmi_clear_overflow(struct dw_hdmi *hdmi) * then write one of the FC registers several times. * * The number of iterations matters and depends on the HDMI TX revision - * (and possibly on the platform). So far only i.MX6Q (v1.30a) and - * i.MX6DL (v1.31a) have been identified as needing the workaround, with - * 4 and 1 iterations respectively. + * (and possibly on the platform). So far i.MX6Q (v1.30a), i.MX6DL + * (v1.31a) and multiple Allwinner SoCs (v1.32a) have been identified + * as needing the workaround, with 4 iterations for v1.30a and 1 + * iteration for others. */ switch (hdmi->version) { @@ -1644,6 +1661,7 @@ static void dw_hdmi_clear_overflow(struct dw_hdmi *hdmi) count = 4; break; case 0x131a: + case 0x132a: count = 1; break; default: @@ -2525,8 +2543,6 @@ __dw_hdmi_probe(struct platform_device *pdev, if (hdmi->i2c) dw_hdmi_i2c_init(hdmi); - platform_set_drvdata(pdev, hdmi); - return hdmi; err_iahb: @@ -2576,25 +2592,23 @@ static void __dw_hdmi_remove(struct dw_hdmi *hdmi) /* ----------------------------------------------------------------------------- * Probe/remove API, used from platforms based on the DRM bridge API. */ -int dw_hdmi_probe(struct platform_device *pdev, - const struct dw_hdmi_plat_data *plat_data) +struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev, + const struct dw_hdmi_plat_data *plat_data) { struct dw_hdmi *hdmi; hdmi = __dw_hdmi_probe(pdev, plat_data); if (IS_ERR(hdmi)) - return PTR_ERR(hdmi); + return hdmi; drm_bridge_add(&hdmi->bridge); - return 0; + return hdmi; } EXPORT_SYMBOL_GPL(dw_hdmi_probe); -void dw_hdmi_remove(struct platform_device *pdev) +void dw_hdmi_remove(struct dw_hdmi *hdmi) { - struct dw_hdmi *hdmi = platform_get_drvdata(pdev); - drm_bridge_remove(&hdmi->bridge); __dw_hdmi_remove(hdmi); @@ -2604,31 +2618,30 @@ EXPORT_SYMBOL_GPL(dw_hdmi_remove); /* ----------------------------------------------------------------------------- * Bind/unbind API, used from platforms based on the component framework. */ -int dw_hdmi_bind(struct platform_device *pdev, struct drm_encoder *encoder, - const struct dw_hdmi_plat_data *plat_data) +struct dw_hdmi *dw_hdmi_bind(struct platform_device *pdev, + struct drm_encoder *encoder, + const struct dw_hdmi_plat_data *plat_data) { struct dw_hdmi *hdmi; int ret; hdmi = __dw_hdmi_probe(pdev, plat_data); if (IS_ERR(hdmi)) - return PTR_ERR(hdmi); + return hdmi; ret = drm_bridge_attach(encoder, &hdmi->bridge, NULL); if (ret) { - dw_hdmi_remove(pdev); + dw_hdmi_remove(hdmi); DRM_ERROR("Failed to initialize bridge with drm\n"); - return ret; + return ERR_PTR(ret); } - return 0; + return hdmi; } EXPORT_SYMBOL_GPL(dw_hdmi_bind); -void dw_hdmi_unbind(struct device *dev) +void dw_hdmi_unbind(struct dw_hdmi *hdmi) { - struct dw_hdmi *hdmi = dev_get_drvdata(dev); - __dw_hdmi_remove(hdmi); } EXPORT_SYMBOL_GPL(dw_hdmi_unbind); diff --git a/drivers/gpu/drm/drm_blend.c b/drivers/gpu/drm/drm_blend.c index 4c62dff14893..5a81e1b4c076 100644 --- a/drivers/gpu/drm/drm_blend.c +++ b/drivers/gpu/drm/drm_blend.c @@ -88,15 +88,17 @@ * On top of this basic transformation additional properties can be exposed by * the driver: * - * - Rotation is set up with drm_plane_create_rotation_property(). It adds a - * rotation and reflection step between the source and destination rectangles. - * Without this property the rectangle is only scaled, but not rotated or - * reflected. + * rotation: + * Rotation is set up with drm_plane_create_rotation_property(). It adds a + * rotation and reflection step between the source and destination rectangles. + * Without this property the rectangle is only scaled, but not rotated or + * reflected. * - * - Z position is set up with drm_plane_create_zpos_immutable_property() and - * drm_plane_create_zpos_property(). It controls the visibility of overlapping - * planes. Without this property the primary plane is always below the cursor - * plane, and ordering between all other planes is undefined. + * zpos: + * Z position is set up with drm_plane_create_zpos_immutable_property() and + * drm_plane_create_zpos_property(). It controls the visibility of overlapping + * planes. Without this property the primary plane is always below the cursor + * plane, and ordering between all other planes is undefined. * * Note that all the property extensions described here apply either to the * plane or the CRTC (e.g. for the background color, which currently is not diff --git a/drivers/gpu/drm/drm_connector.c b/drivers/gpu/drm/drm_connector.c index 16b9c3810af2..b3cde897cd80 100644 --- a/drivers/gpu/drm/drm_connector.c +++ b/drivers/gpu/drm/drm_connector.c @@ -849,13 +849,13 @@ DRM_ENUM_NAME_FN(drm_get_content_protection_name, drm_cp_enum_list) * * The value of this property can be one of the following: * - * - DRM_MODE_CONTENT_PROTECTION_UNDESIRED = 0 + * DRM_MODE_CONTENT_PROTECTION_UNDESIRED = 0 * The link is not protected, content is transmitted in the clear. - * - DRM_MODE_CONTENT_PROTECTION_DESIRED = 1 + * DRM_MODE_CONTENT_PROTECTION_DESIRED = 1 * Userspace has requested content protection, but the link is not * currently protected. When in this state, kernel should enable * Content Protection as soon as possible. - * - DRM_MODE_CONTENT_PROTECTION_ENABLED = 2 + * DRM_MODE_CONTENT_PROTECTION_ENABLED = 2 * Userspace has requested content protection, and the link is * protected. Only the driver can set the property to this value. * If userspace attempts to set to ENABLED, kernel will return @@ -889,7 +889,31 @@ DRM_ENUM_NAME_FN(drm_get_content_protection_name, drm_cp_enum_list) * INPUT_PROP_DIRECT) will still map 1:1 to the actual LCD panel * coordinates, so if userspace rotates the picture to adjust for * the orientation it must also apply the same transformation to the - * touchscreen input coordinates. + * touchscreen input coordinates. This property is initialized by calling + * drm_connector_init_panel_orientation_property(). + * + * scaling mode: + * This property defines how a non-native mode is upscaled to the native + * mode of an LCD panel: + * + * None: + * No upscaling happens, scaling is left to the panel. Not all + * drivers expose this mode. + * Full: + * The output is upscaled to the full resolution of the panel, + * ignoring the aspect ratio. + * Center: + * No upscaling happens, the output is centered within the native + * resolution the panel. + * Full aspect: + * The output is upscaled to maximize either the width or height + * while retaining the aspect ratio. + * + * This property should be set up by calling + * drm_connector_attach_scaling_mode_property(). Note that drivers + * can also expose this property to external outputs, in which case they + * must support "None", which should be the default (since external screens + * have a built-in scaler). */ int drm_connector_create_standard_properties(struct drm_device *dev) diff --git a/drivers/gpu/drm/drm_dp_mst_topology.c b/drivers/gpu/drm/drm_dp_mst_topology.c index 36df7df5fe1a..6fac4129e6a2 100644 --- a/drivers/gpu/drm/drm_dp_mst_topology.c +++ b/drivers/gpu/drm/drm_dp_mst_topology.c @@ -1082,10 +1082,12 @@ static bool drm_dp_port_setup_pdt(struct drm_dp_mst_port *port) lct = drm_dp_calculate_rad(port, rad); port->mstb = drm_dp_add_mst_branch_device(lct, rad); - port->mstb->mgr = port->mgr; - port->mstb->port_parent = port; + if (port->mstb) { + port->mstb->mgr = port->mgr; + port->mstb->port_parent = port; - |