diff options
65 files changed, 2788 insertions, 966 deletions
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml new file mode 100644 index 000000000000..70eaf739036b --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml @@ -0,0 +1,252 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings + +description: | + The FMC2 functional block makes the interface with: synchronous and + asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped + peripherals) and NAND flash memories. + Its main purposes are: + - to translate AXI transactions into the appropriate external device + protocol + - to meet the access time requirements of the external devices + All external devices share the addresses, data and control signals with the + controller. Each external device is accessed by means of a unique Chip + Select. The FMC2 performs only one access at a time to an external device. + +maintainers: + - Christophe Kerello <christophe.kerello@st.com> + +properties: + compatible: + const: st,stm32mp1-fmc2-ebi + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#address-cells": + const: 2 + + "#size-cells": + const: 1 + + ranges: + description: | + Reflects the memory layout with four integer values per bank. Format: + <bank-number> 0 <address of the bank> <size> + +patternProperties: + "^.*@[0-4],[a-f0-9]+$": + type: object + + properties: + reg: + description: Bank number, base address and size of the device. + + st,fmc2-ebi-cs-transaction-type: + description: | + Select one of the transactions type supported + 0: Asynchronous mode 1 SRAM/FRAM. + 1: Asynchronous mode 1 PSRAM. + 2: Asynchronous mode A SRAM/FRAM. + 3: Asynchronous mode A PSRAM. + 4: Asynchronous mode 2 NOR. + 5: Asynchronous mode B NOR. + 6: Asynchronous mode C NOR. + 7: Asynchronous mode D NOR. + 8: Synchronous read synchronous write PSRAM. + 9: Synchronous read asynchronous write PSRAM. + 10: Synchronous read synchronous write NOR. + 11: Synchronous read asynchronous write NOR. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 11 + + st,fmc2-ebi-cs-cclk-enable: + description: Continuous clock enable (first bank must be configured + in synchronous mode). The FMC_CLK is generated continuously + during asynchronous and synchronous access. By default, the + FMC_CLK is only generated during synchronous access. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-mux-enable: + description: Address/Data multiplexed on databus (valid only with + NOR and PSRAM transactions type). By default, Address/Data + are not multiplexed. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-buswidth: + description: Data bus width + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 8, 16 ] + default: 16 + + st,fmc2-ebi-cs-waitpol-high: + description: Wait signal polarity (NWAIT signal active high). + By default, NWAIT is active low. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-waitcfg-enable: + description: The NWAIT signal indicates wheither the data from the + device are valid or if a wait state must be inserted when accessing + the device in synchronous mode. By default, the NWAIT signal is + active one data cycle before wait state. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-wait-enable: + description: The NWAIT signal is enabled (its level is taken into + account after the programmed latency period to insert wait states + if asserted). By default, the NWAIT signal is disabled. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-asyncwait-enable: + description: The NWAIT signal is taken into account during asynchronous + transactions. By default, the NWAIT signal is not taken into account + during asynchronous transactions. + $ref: /schemas/types.yaml#/definitions/flag + + st,fmc2-ebi-cs-cpsize: + description: CRAM page size. The controller splits the burst access + when the memory page is reached. By default, no burst split when + crossing page boundary. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 128, 256, 512, 1024 ] + default: 0 + + st,fmc2-ebi-cs-byte-lane-setup-ns: + description: This property configures the byte lane setup timing + defined in nanoseconds from NBLx low to Chip Select NEx low. + + st,fmc2-ebi-cs-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed read/write + transactions. + + st,fmc2-ebi-cs-data-setup-ns: + description: This property defines the duration of the data setup phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-bus-turnaround-ns: + description: This property defines the delay in nanoseconds between the + end of current read/write transaction and the next transaction. + + st,fmc2-ebi-cs-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous read/write transactions. + + st,fmc2-ebi-cs-clk-period-ns: + description: This property defines the FMC_CLK output signal period in + nanoseconds. + + st,fmc2-ebi-cs-data-latency-ns: + description: This property defines the data latency before reading or + writing the first data in nanoseconds. + + st,fmc2_ebi-cs-write-address-setup-ns: + description: This property defines the duration of the address setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-address-hold-ns: + description: This property defines the duration of the address hold + phase in nanoseconds used for asynchronous multiplexed write + transactions. + + st,fmc2-ebi-cs-write-data-setup-ns: + description: This property defines the duration of the data setup + phase in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-write-bus-turnaround-ns: + description: This property defines the delay between the end of current + write transaction and the next transaction in nanoseconds. + + st,fmc2-ebi-cs-write-data-hold-ns: + description: This property defines the duration of the data hold phase + in nanoseconds used for asynchronous write transactions. + + st,fmc2-ebi-cs-max-low-pulse-ns: + description: This property defines the maximum chip select low pulse + duration in nanoseconds for synchronous transactions. When this timing + reaches 0, the controller splits the current access, toggles NE to + allow device refresh and restarts a new access. + + required: + - reg + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + - clocks + - ranges + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + memory-controller@58002000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "st,stm32mp1-fmc2-ebi"; + reg = <0x58002000 0x1000>; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; + + ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */ + <1 0 0x64000000 0x04000000>, /* EBI CS 2 */ + <2 0 0x68000000 0x04000000>, /* EBI CS 3 */ + <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */ + <4 0 0x80000000 0x10000000>; /* NAND */ + + psram@0,0 { + compatible = "mtd-ram"; + reg = <0 0x00000000 0x100000>; + bank-width = <2>; + + st,fmc2-ebi-cs-transaction-type = <1>; + st,fmc2-ebi-cs-address-setup-ns = <60>; + st,fmc2-ebi-cs-data-setup-ns = <30>; + st,fmc2-ebi-cs-bus-turnaround-ns = <5>; + }; + + nand-controller@4,0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "st,stm32mp1-fmc2-nfc"; + reg = <4 0x00000000 0x1000>, + <4 0x08010000 0x1000>, + <4 0x08020000 0x1000>, + <4 0x01000000 0x1000>, + <4 0x09010000 0x1000>, + <4 0x09020000 0x1000>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + + nand@0 { + reg = <0>; + nand-on-flash-bbt; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt index cfb18abe6001..edebeae1f5b3 100644 --- a/Documentation/devicetree/bindings/mtd/davinci-nand.txt +++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt @@ -4,8 +4,8 @@ This file provides information, what the device node for the davinci/keystone NAND interface contains. Documentation: -Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf -Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf +Davinci DM646x - https://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf +Kestone - https://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf Required properties: diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt index fce4894f5a98..25f07c1f9e44 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt @@ -7,14 +7,16 @@ Required properties: - fsl,upm-cmd-offset : UPM pattern offset for the command latch. Optional properties: -- fsl,upm-wait-flags : add chip-dependent short delays after running the - UPM pattern (0x1), after writing a data byte (0x2) or after - writing out a buffer (0x4). - fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support. The corresponding address lines are used to select the chip. - gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins (R/B#). For multi-chip devices, "n" GPIO definitions are required according to the number of chips. + +Deprecated properties: +- fsl,upm-wait-flags : add chip-dependent short delays after running the + UPM pattern (0x1), after writing a data byte (0x2) or after + writing out a buffer (0x4). - chip-delay : chip dependent delay for transferring data from array to read registers (tR). Required if property "gpios" is not used (R/B# pins not connected). @@ -52,8 +54,6 @@ upm@3,0 { fsl,upm-cmd-offset = <0x08>; /* Multi-chip NAND device */ fsl,upm-addr-line-cs-offsets = <0x0 0x200>; - fsl,upm-wait-flags = <0x5>; - chip-delay = <25>; // in micro-seconds nand@0 { #address-cells = <1>; diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml index cde7c4d79efe..40fc5b0b2b8c 100644 --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml @@ -114,6 +114,13 @@ patternProperties: description: Contains the native Ready/Busy IDs. + rb-gpios: + description: + Contains one or more GPIO descriptor (the numper of descriptor + depends on the number of R/B pins exposed by the flash) for the + Ready/Busy pins. Active state refers to the NAND ready state and + should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted. + required: - reg diff --git a/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml index b059267f6d20..6ae7de15d172 100644 --- a/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml +++ b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml @@ -9,32 +9,19 @@ title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings maintainers: - Christophe Kerello <christophe.kerello@st.com> -allOf: - - $ref: "nand-controller.yaml#" - properties: compatible: - const: st,stm32mp15-fmc2 + enum: + - st,stm32mp15-fmc2 + - st,stm32mp1-fmc2-nfc reg: - items: - - description: Registers - - description: Chip select 0 data - - description: Chip select 0 command - - description: Chip select 0 address space - - description: Chip select 1 data - - description: Chip select 1 command - - description: Chip select 1 address space + minItems: 6 + maxItems: 7 interrupts: maxItems: 1 - clocks: - maxItems: 1 - - resets: - maxItems: 1 - dmas: items: - description: tx DMA channel @@ -57,11 +44,55 @@ patternProperties: nand-ecc-strength: enum: [1, 4 ,8 ] +allOf: + - $ref: "nand-controller.yaml#" + + - if: + properties: + compatible: + contains: + const: st,stm32mp15-fmc2 + then: + properties: + reg: + items: + - description: Registers + - description: Chip select 0 data + - description: Chip select 0 command + - description: Chip select 0 address space + - description: Chip select 1 data + - description: Chip select 1 command + - description: Chip select 1 address space + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + required: + - clocks + + - if: + properties: + compatible: + contains: + const: st,stm32mp1-fmc2-nfc + then: + properties: + reg: + items: + - description: Chip select 0 data + - description: Chip select 0 command + - description: Chip select 0 address space + - description: Chip select 1 data + - description: Chip select 1 command + - description: Chip select 1 address space + required: - compatible - reg - interrupts - - clocks examples: - | @@ -77,13 +108,13 @@ examples: <0x81000000 0x1000>, <0x89010000 0x1000>, <0x89020000 0x1000>; - interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; - dmas = <&mdma1 20 0x10 0x12000a02 0x0 0x0>, - <&mdma1 20 0x10 0x12000a08 0x0 0x0>, - <&mdma1 21 0x10 0x12000a0a 0x0 0x0>; - dma-names = "tx", "rx", "ecc"; - clocks = <&rcc FMC_K>; - resets = <&rcc FMC_R>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>, + <&mdma1 20 0x2 0x12000a08 0x0 0x0>, + <&mdma1 21 0x2 0x12000a0a 0x0 0x0>; + dma-names = "tx", "rx", "ecc"; + clocks = <&rcc FMC_K>; + resets = <&rcc FMC_R>; #address-cells = <1>; #size-cells = <0>; diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig index 97440af499b0..2c79e95dd486 100644 --- a/drivers/memory/Kconfig +++ b/drivers/memory/Kconfig @@ -188,6 +188,16 @@ config RENESAS_RPCIF host or HyperFlash. You'll have to select individual components under the corresponding menu. +config STM32_FMC2_EBI + tristate "Support for FMC2 External Bus Interface on STM32MP SoCs" + depends on MACH_STM32MP157 || COMPILE_TEST + select MFD_SYSCON + help + Select this option to enable the STM32 FMC2 External Bus Interface + controller. This driver configures the transactions with external + devices (like SRAM, ethernet adapters, FPGAs, LCD displays, ...) on + SOCs containing the FMC2 External Bus Interface. + source "drivers/memory/samsung/Kconfig" source "drivers/memory/tegra/Kconfig" diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile index d105f8ebe8b8..b4533ffff2bc 100644 --- a/drivers/memory/Makefile +++ b/drivers/memory/Makefile @@ -23,6 +23,7 @@ obj-$(CONFIG_MTK_SMI) += mtk-smi.o obj-$(CONFIG_DA8XX_DDRCTL) += da8xx-ddrctl.o obj-$(CONFIG_PL353_SMC) += pl353-smc.o obj-$(CONFIG_RENESAS_RPCIF) += renesas-rpc-if.o +obj-$(CONFIG_STM32_FMC2_EBI) += stm32-fmc2-ebi.o obj-$(CONFIG_SAMSUNG_MC) += samsung/ obj-$(CONFIG_TEGRA_MC) += tegra/ diff --git a/drivers/memory/stm32-fmc2-ebi.c b/drivers/memory/stm32-fmc2-ebi.c new file mode 100644 index 000000000000..4d5758c419c5 --- /dev/null +++ b/drivers/memory/stm32-fmc2-ebi.c @@ -0,0 +1,1206 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) STMicroelectronics 2020 + */ + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of_platform.h> +#include <linux/pinctrl/consumer.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +/* FMC2 Controller Registers */ +#define FMC2_BCR1 0x0 +#define FMC2_BTR1 0x4 +#define FMC2_BCR(x) ((x) * 0x8 + FMC2_BCR1) +#define FMC2_BTR(x) ((x) * 0x8 + FMC2_BTR1) +#define FMC2_PCSCNTR 0x20 +#define FMC2_BWTR1 0x104 +#define FMC2_BWTR(x) ((x) * 0x8 + FMC2_BWTR1) + +/* Register: FMC2_BCR1 */ +#define FMC2_BCR1_CCLKEN BIT(20) +#define FMC2_BCR1_FMC2EN BIT(31) + +/* Register: FMC2_BCRx */ +#define FMC2_BCR_MBKEN BIT(0) +#define FMC2_BCR_MUXEN BIT(1) +#define FMC2_BCR_MTYP GENMASK(3, 2) +#define FMC2_BCR_MWID GENMASK(5, 4) +#define FMC2_BCR_FACCEN BIT(6) +#define FMC2_BCR_BURSTEN BIT(8) +#define FMC2_BCR_WAITPOL BIT(9) +#define FMC2_BCR_WAITCFG BIT(11) +#define FMC2_BCR_WREN BIT(12) +#define FMC2_BCR_WAITEN BIT(13) +#define FMC2_BCR_EXTMOD BIT(14) +#define FMC2_BCR_ASYNCWAIT BIT(15) +#define FMC2_BCR_CPSIZE GENMASK(18, 16) +#define FMC2_BCR_CBURSTRW BIT(19) |