diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
39 files changed, 1094 insertions, 47 deletions
diff --git a/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt new file mode 100644 index 000000000000..94e642a33db0 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda/l2ecc.txt @@ -0,0 +1,15 @@ +Calxeda Highbank L2 cache ECC + +Properties: +- compatible : Should be "calxeda,hb-sregs-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. + +Example: + + sregs@fff3c200 { + compatible = "calxeda,hb-sregs-l2-ecc"; + reg = <0xfff3c200 0x100>; + interrupts = <0 71 4 0 72 4>; + }; diff --git a/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt new file mode 100644 index 000000000000..f770ac0893d4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/calxeda/mem-ctrlr.txt @@ -0,0 +1,14 @@ +Calxeda DDR memory controller + +Properties: +- compatible : Should be "calxeda,hb-ddr-ctrl" +- reg : Address and size for DDR controller registers. +- interrupts : Interrupt for DDR controller. + +Example: + + memory-controller@fff00000 { + compatible = "calxeda,hb-ddr-ctrl"; + reg = <0xfff00000 0x1000>; + interrupts = <0 91 4>; + }; diff --git a/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt new file mode 100644 index 000000000000..93986a5a8018 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/cavium-compact-flash.txt @@ -0,0 +1,30 @@ +* Compact Flash + +The Cavium Compact Flash device is connected to the Octeon Boot Bus, +and is thus a child of the Boot Bus device. It can read and write +industry standard compact flash devices. + +Properties: +- compatible: "cavium,ebt3000-compact-flash"; + + Compatibility with many Cavium evaluation boards. + +- reg: The base address of the the CF chip select banks. Depending on + the device configuration, there may be one or two banks. + +- cavium,bus-width: The width of the connection to the CF devices. Valid + values are 8 and 16. + +- cavium,true-ide: Optional, if present the CF connection is in True IDE mode. + +- cavium,dma-engine-handle: Optional, a phandle for the DMA Engine connected + to this device. + +Example: + compact-flash@5,0 { + compatible = "cavium,ebt3000-compact-flash"; + reg = <5 0 0x10000>, <6 0 0x10000>; + cavium,bus-width = <16>; + cavium,true-ide; + cavium,dma-engine-handle = <&dma0>; + }; diff --git a/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt new file mode 100644 index 000000000000..9d6dcd3fe7f9 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/cavium-octeon-gpio.txt @@ -0,0 +1,49 @@ +* General Purpose Input Output (GPIO) bus. + +Properties: +- compatible: "cavium,octeon-3860-gpio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the GPIO unit's register bank. + +- gpio-controller: This is a GPIO controller. + +- #gpio-cells: Must be <2>. The first cell is the GPIO pin. + +- interrupt-controller: The GPIO controller is also an interrupt + controller, many of its pins may be configured as an interrupt + source. + +- #interrupt-cells: Must be <2>. The first cell is the GPIO pin + connected to the interrupt source. The second cell is the interrupt + triggering protocol and may have one of four values: + 1 - edge triggered on the rising edge. + 2 - edge triggered on the falling edge + 4 - level triggered active high. + 8 - level triggered active low. + +- interrupts: Interrupt routing for each pin. + +Example: + + gpio-controller@1070000000800 { + #gpio-cells = <2>; + compatible = "cavium,octeon-3860-gpio"; + reg = <0x10700 0x00000800 0x0 0x100>; + gpio-controller; + /* Interrupts are specified by two parts: + * 1) GPIO pin number (0..15) + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + interrupt-controller; + #interrupt-cells = <2>; + /* The GPIO pin connect to 16 consecutive CUI bits */ + interrupts = <0 16>, <0 17>, <0 18>, <0 19>, + <0 20>, <0 21>, <0 22>, <0 23>, + <0 24>, <0 25>, <0 26>, <0 27>, + <0 28>, <0 29>, <0 30>, <0 31>; + }; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index 4f3929713ae4..dbd22e0df21e 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -22,7 +22,7 @@ Required properties: Example: gpio0: gpio@73f84000 { - compatible = "fsl,imx51-gpio", "fsl,imx31-gpio"; + compatible = "fsl,imx51-gpio", "fsl,imx35-gpio"; reg = <0x73f84000 0x4000>; interrupts = <50 51>; gpio-controller; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index 8f50fe5e6c42..5375625e8cd2 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -11,14 +11,15 @@ Required properties: <[phandle of the gpio controller node] [pin number within the gpio controller] [mux function] - [pull up/down] + [flags and pull up/down] [drive strength]> Values for gpio specifier: - Pin number: is a value between 0 to 7. - - Pull Up/Down: 0 - Pull Up/Down Disabled. - 1 - Pull Down Enabled. - 3 - Pull Up Enabled. + - Flags and Pull Up/Down: 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 3 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. - Drive Strength: 0 - 1x, 1 - 3x, 2 - 2x, diff --git a/Documentation/devicetree/bindings/i2c/cavium-i2c.txt b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt new file mode 100644 index 000000000000..dced82ebe31d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/cavium-i2c.txt @@ -0,0 +1,34 @@ +* Two Wire Serial Interface (TWSI) / I2C + +- compatible: "cavium,octeon-3860-twsi" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the TWSI/I2C bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. I2C addresses have no size component. + +- interrupts: A single interrupt specifier. + +- clock-frequency: The I2C bus clock rate in Hz. + +Example: + twsi0: i2c@1180000001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cavium,octeon-3860-twsi"; + reg = <0x11800 0x00001000 0x0 0x200>; + interrupts = <0 45>; + clock-frequency = <100000>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + }; + tmp@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt index 4f8ec947c6bd..4f8ec947c6bd 100644 --- a/Documentation/devicetree/bindings/gpio/gpio_i2c.txt +++ b/Documentation/devicetree/bindings/i2c/gpio-i2c.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt index 1bfc02de1b0c..30ac3a0557f7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -4,6 +4,8 @@ Required properties: - compatible: Should be "fsl,<chip>-i2c" - reg: Should contain registers location and length - interrupts: Should contain ERROR and DMA interrupts +- clock-frequency: Desired I2C bus clock frequency in Hz. + Only 100000Hz and 400000Hz modes are supported. Examples: @@ -13,4 +15,5 @@ i2c0: i2c@80058000 { compatible = "fsl,imx28-i2c"; reg = <0x80058000 2000>; interrupts = <111 68>; + clock-frequency = <100000>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt new file mode 100644 index 000000000000..c15781f4dc8c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -0,0 +1,33 @@ +Device tree configuration for i2c-ocores + +Required properties: +- compatible : "opencores,i2c-ocores" +- reg : bus address start and address range size of device +- interrupts : interrupt number +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- reg-shift : device register offsets are shifted by this value +- reg-io-width : io register width in bytes (1, 2 or 4) +- regstep : deprecated, use reg-shift above + +Example: + + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + clock-frequency = <20000000>; + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt index b891ee218354..0f7945019f6f 100644 --- a/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt +++ b/Documentation/devicetree/bindings/i2c/mrvl-i2c.txt @@ -1,4 +1,4 @@ -* I2C +* Marvell MMP I2C controller Required properties : @@ -32,3 +32,20 @@ Examples: interrupts = <58>; }; +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be "marvell,mv64xxx-i2c" + - interrupts : The interrupt number + - clock-frequency : Desired I2C bus clock frequency in Hz. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt new file mode 100644 index 000000000000..31afd5014c48 --- /dev/null +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -0,0 +1,28 @@ +NXP LPC32xx Key Scan Interface + +Required Properties: +- compatible: Should be "nxp,lpc3220-key" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. +- keypad,num-rows: Number of rows and columns, e.g. 1: 1x1, 6: 6x6 +- keypad,num-columns: Must be equal to keypad,num-rows since LPC32xx only + supports square matrices +- nxp,debounce-delay-ms: Debounce delay in ms +- nxp,scan-delay-ms: Repeated scan period in ms +- linux,keymap: the key-code to be reported when the key is pressed + and released, see also + Documentation/devicetree/bindings/input/matrix-keymap.txt + +Example: + + key@40050000 { + compatible = "nxp,lpc3220-key"; + reg = <0x40050000 0x1000>; + interrupts = <54 0>; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt new file mode 100644 index 000000000000..f2fa5e10493d --- /dev/null +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -0,0 +1,31 @@ +* TI's Keypad Controller device tree bindings + +TI's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,omap4-keypad": For controllers compatible with omap4 keypad + controller. + +Required Board Specific Properties, in addition to those specified by +the shared matrix-keyboard bindings: +- keypad,num-rows: Number of row lines connected to the keypad + controller. + +- keypad,num-columns: Number of column lines connected to the + keypad controller. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. + +Example: + keypad@4ae1c000{ + compatible = "ti,omap4-keypad"; + keypad,num-rows = <2>; + keypad,num-columns = <8>; + linux,keypad-no-autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/twl6040-vibra.txt b/Documentation/devicetree/bindings/input/twl6040-vibra.txt deleted file mode 100644 index 5b1918b818fb..000000000000 --- a/Documentation/devicetree/bindings/input/twl6040-vibra.txt +++ /dev/null @@ -1,37 +0,0 @@ -Vibra driver for the twl6040 family - -The vibra driver is a child of the twl6040 MFD dirver. -Documentation/devicetree/bindings/mfd/twl6040.txt - -Required properties: -- compatible : Must be "ti,twl6040-vibra"; -- interrupts: 4, Vibra overcurrent interrupt -- vddvibl-supply: Regulator supplying the left vibra motor -- vddvibr-supply: Regulator supplying the right vibra motor -- vibldrv_res: Board specific left driver resistance -- vibrdrv_res: Board specific right driver resistance -- viblmotor_res: Board specific left motor resistance -- vibrmotor_res: Board specific right motor resistance - -Optional properties: -- vddvibl_uV: If the vddvibl default voltage need to be changed -- vddvibr_uV: If the vddvibr default voltage need to be changed - -Example: -/* - * 8-channel high quality low-power audio codec - * http://www.ti.com/lit/ds/symlink/twl6040.pdf - */ -twl6040: twl6040@4b { - ... - twl6040_vibra: twl6040@1 { - compatible = "ti,twl6040-vibra"; - interrupts = <4>; - vddvibl-supply = <&vbat>; - vddvibr-supply = <&vbat>; - vibldrv_res = <8>; - vibrdrv_res = <3>; - viblmotor_res = <10>; - vibrmotor_res = <10>; - }; -}; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt new file mode 100644 index 000000000000..69e757a657a0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -0,0 +1,123 @@ +* AB8500 Multi-Functional Device (MFD) + +Required parent device properties: +- compatible : contains "stericsson,ab8500"; +- interrupts : contains the IRQ line for the AB8500 +- interrupt-controller : describes the AB8500 as an Interrupt Controller (has its own domain) +- #interrupt-cells : should be 2, for 2-cell format + - The first cell is the AB8500 local IRQ number + - The second cell is used to specify optional parameters + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +Optional parent device properties: +- reg : contains the PRCMU mailbox address for the AB8500 i2c port + +The AB8500 consists of a large and varied group of sub-devices: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +ab8500-bm : : : Battery Manager +ab8500-btemp : : : Battery Temperature +ab8500-charger : : : Battery Charger +ab8500-fg : : : Fuel Gauge +ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter + SW_CONV_END : : +ab8500-gpio : : : GPIO Controller +ab8500-ponkey : ONKEY_DBF : : Power-on Key + ONKEY_DBR : : +ab8500-pwm : : : Pulse Width Modulator +ab8500-regulator : : : Regulators +ab8500-rtc : 60S : : Real Time Clock + : ALARM : : +ab8500-sysctrl : : : System Control +ab8500-usb : ID_WAKEUP_R : vddulpivio18 : Universal Serial Bus + : ID_WAKEUP_F : v-ape : + : VBUS_DET_F : musb_1v8 : + : VBUS_DET_R : : + : USB_LINK_STATUS : : + : USB_ADP_PROBE_PLUG : : + : USB_ADP_PROBE_UNPLUG : : + +Required child device properties: +- compatible : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey| + pwm|regulator|rtc|sysctrl|usb]"; + +Optional child device properties: +- interrupts : contains the device IRQ(s) using the 2-cell format (see above) +- interrupt-names : contains names of IRQ resource in the order in which they were + supplied in the interrupts property +- <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree + +ab8500@5 { + compatible = "stericsson,ab8500"; + reg = <5>; /* mailbox 5 is i2c */ + interrupts = <0 40 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + + ab8500-rtc { + compatible = "stericsson,ab8500-rtc"; + interrupts = <17 0x4 + 18 0x4>; + interrupt-names = "60S", "ALARM"; + }; + + ab8500-gpadc { + compatible = "stericsson,ab8500-gpadc"; + interrupts = <32 0x4 + 39 0x4>; + interrupt-names = "HW_CONV_END", "SW_CONV_END"; + vddadc-supply = <&ab8500_ldo_tvout_reg>; + }; + + ab8500-usb { + compatible = "stericsson,ab8500-usb"; + interrupts = < 90 0x4 + 96 0x4 + 14 0x4 + 15 0x4 + 79 0x4 + 74 0x4 + 75 0x4>; + interrupt-names = "ID_WAKEUP_R", + "ID_WAKEUP_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_ADP_PROBE_PLUG", + "USB_ADP_PROBE_UNPLUG"; + vddulpivio18-supply = <&ab8500_ldo_initcore_reg>; + v-ape-supply = <&db8500_vape_reg>; + musb_1v8-supply = <&db8500_vsmps2_reg>; + }; + + ab8500-ponkey { + compatible = "stericsson,ab8500-ponkey"; + interrupts = <6 0x4 + 7 0x4>; + interrupt-names = "ONKEY_DBF", "ONKEY_DBR"; + }; + + ab8500-sysctrl { + compatible = "stericsson,ab8500-sysctrl"; + }; + + ab8500-pwm { + compatible = "stericsson,ab8500-pwm"; + }; + + ab8500-regulators { + compatible = "stericsson,ab8500-regulator"; + + ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { + /* + * See: Documentation/devicetree/bindings/regulator/regulator.txt + * for more information on regulators + */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt new file mode 100644 index 000000000000..c6a3469d3436 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -0,0 +1,59 @@ +Maxim MAX77686 multi-function device + +MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +interfaced to host controller using i2c interface. PMIC and Charger submodules +are addressed using same i2c slave address whereas RTC submodule uses +different i2c slave address,presently for which we are statically creating i2c +client while probing.This document describes the binding for mfd device and +PMIC submodule. + +Required properties: +- compatible : Must be "maxim,max77686"; +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator-compatible property of regulator should initialized with string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + +Example: + + max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg { + regulator-compatible = "LDO11"; + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg { + regulator-compatible = "BUCK1"; + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + } diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt index d2802d4717bc..db03599ae4dc 100644 --- a/Documentation/devicetree/bindings/mfd/tps65910.txt +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -81,7 +81,7 @@ Example: ti,vmbch-threshold = 0; ti,vmbch2-threshold = 0; - + ti,en-ck32k-xtal; ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; vcc1-supply = <®_parent>; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt index bc67c6f424aa..c855240f3a0e 100644 --- a/Documentation/devicetree/bindings/mfd/twl6040.txt +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -6,7 +6,7 @@ They are connected ot the host processor via i2c for commands, McPDM for audio data and commands. Required properties: -- compatible : Must be "ti,twl6040"; +- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041 - reg: must be 0x4b for i2c address - interrupts: twl6040 has one interrupt line connecteded to the main SoC - interrupt-parent: The parent interrupt controller diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt new file mode 100644 index 000000000000..6581478225a2 --- /dev/null +++ b/ |