diff options
Diffstat (limited to 'drivers/thermal')
23 files changed, 752 insertions, 598 deletions
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig index 7edc8dc6bbab..d7f44deab5b1 100644 --- a/drivers/thermal/Kconfig +++ b/drivers/thermal/Kconfig @@ -450,15 +450,6 @@ depends on (ARCH_STI || ARCH_STM32) && OF source "drivers/thermal/st/Kconfig" endmenu -config TANGO_THERMAL - tristate "Tango thermal management" - depends on ARCH_TANGO || COMPILE_TEST - help - Enable the Tango thermal driver, which supports the primitive - temperature sensor embedded in Tango chips since the SMP8758. - This sensor only generates a 1-bit signal to indicate whether - the die temperature exceeds a programmable threshold. - source "drivers/thermal/tegra/Kconfig" config GENERIC_ADC_THERMAL @@ -476,14 +467,6 @@ depends on (ARCH_QCOM && OF) || COMPILE_TEST source "drivers/thermal/qcom/Kconfig" endmenu -config ZX2967_THERMAL - tristate "Thermal sensors on zx2967 SoC" - depends on ARCH_ZX || COMPILE_TEST - help - Enable the zx2967 thermal sensors driver, which supports - the primitive temperature sensor embedded in zx2967 SoCs. - This sensor generates the real time die temperature. - config UNIPHIER_THERMAL tristate "Socionext UniPhier thermal driver" depends on ARCH_UNIPHIER || COMPILE_TEST diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile index b64dd50a6629..82fc3e616e54 100644 --- a/drivers/thermal/Makefile +++ b/drivers/thermal/Makefile @@ -42,7 +42,6 @@ obj-y += samsung/ obj-$(CONFIG_DOVE_THERMAL) += dove_thermal.o obj-$(CONFIG_DB8500_THERMAL) += db8500_thermal.o obj-$(CONFIG_ARMADA_THERMAL) += armada_thermal.o -obj-$(CONFIG_TANGO_THERMAL) += tango_thermal.o obj-$(CONFIG_IMX_THERMAL) += imx_thermal.o obj-$(CONFIG_IMX_SC_THERMAL) += imx_sc_thermal.o obj-$(CONFIG_IMX8MM_THERMAL) += imx8mm_thermal.o @@ -57,7 +56,6 @@ obj-y += tegra/ obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o obj-$(CONFIG_GENERIC_ADC_THERMAL) += thermal-generic-adc.o -obj-$(CONFIG_ZX2967_THERMAL) += zx2967_thermal.o obj-$(CONFIG_UNIPHIER_THERMAL) += uniphier_thermal.o obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o diff --git a/drivers/thermal/cpufreq_cooling.c b/drivers/thermal/cpufreq_cooling.c index f5af2571f9b7..10af3341e5ea 100644 --- a/drivers/thermal/cpufreq_cooling.c +++ b/drivers/thermal/cpufreq_cooling.c @@ -485,7 +485,7 @@ static int cpufreq_set_cur_state(struct thermal_cooling_device *cdev, frequency = get_state_freq(cpufreq_cdev, state); ret = freq_qos_update_request(&cpufreq_cdev->qos_req, frequency); - if (ret > 0) { + if (ret >= 0) { cpufreq_cdev->cpufreq_state = state; cpus = cpufreq_cdev->policy->cpus; max_capacity = arch_scale_cpu_capacity(cpumask_first(cpus)); diff --git a/drivers/thermal/da9062-thermal.c b/drivers/thermal/da9062-thermal.c index 4d74994f160a..180edec34e07 100644 --- a/drivers/thermal/da9062-thermal.c +++ b/drivers/thermal/da9062-thermal.c @@ -95,7 +95,7 @@ static void da9062_thermal_poll_on(struct work_struct *work) thermal_zone_device_update(thermal->zone, THERMAL_EVENT_UNSPECIFIED); - delay = msecs_to_jiffies(thermal->zone->passive_delay); + delay = thermal->zone->passive_delay_jiffies; queue_delayed_work(system_freezable_wq, &thermal->work, delay); return; } @@ -245,7 +245,7 @@ static int da9062_thermal_probe(struct platform_device *pdev) dev_dbg(&pdev->dev, "TJUNC temperature polling period set at %d ms\n", - thermal->zone->passive_delay); + jiffies_to_msecs(thermal->zone->passive_delay_jiffies)); ret = platform_get_irq_byname(pdev, "THERMAL"); if (ret < 0) { diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c index 7a4170a0b51f..92acae53df49 100644 --- a/drivers/thermal/gov_power_allocator.c +++ b/drivers/thermal/gov_power_allocator.c @@ -258,7 +258,7 @@ static u32 pid_controller(struct thermal_zone_device *tz, * power being applied, slowing down the controller) */ d = mul_frac(tz->tzp->k_d, err - params->prev_err); - d = div_frac(d, tz->passive_delay); + d = div_frac(d, jiffies_to_msecs(tz->passive_delay_jiffies)); params->prev_err = err; power_range = p + i + d; @@ -590,13 +590,42 @@ static void allow_maximum_power(struct thermal_zone_device *tz) } /** + * check_power_actors() - Check all cooling devices and warn when they are + * not power actors + * @tz: thermal zone to operate on + * + * Check all cooling devices in the @tz and warn every time they are missing + * power actor API. The warning should help to investigate the issue, which + * could be e.g. lack of Energy Model for a given device. + * + * Return: 0 on success, -EINVAL if any cooling device does not implement + * the power actor API. + */ +static int check_power_actors(struct thermal_zone_device *tz) +{ + struct thermal_instance *instance; + int ret = 0; + + list_for_each_entry(instance, &tz->thermal_instances, tz_node) { + if (!cdev_is_power_actor(instance->cdev)) { + dev_warn(&tz->device, "power_allocator: %s is not a power actor\n", + instance->cdev->type); + ret = -EINVAL; + } + } + + return ret; +} + +/** * power_allocator_bind() - bind the power_allocator governor to a thermal zone * @tz: thermal zone to bind it to * * Initialize the PID controller parameters and bind it to the thermal * zone. * - * Return: 0 on success, or -ENOMEM if we ran out of memory. + * Return: 0 on success, or -ENOMEM if we ran out of memory, or -EINVAL + * when there are unsupported cooling devices in the @tz. */ static int power_allocator_bind(struct thermal_zone_device *tz) { @@ -604,6 +633,10 @@ static int power_allocator_bind(struct thermal_zone_device *tz) struct power_allocator_params *params; int control_temp; + ret = check_power_actors(tz); + if (ret) + return ret; + params = kzalloc(sizeof(*params), GFP_KERNEL); if (!params) return -ENOMEM; diff --git a/drivers/thermal/gov_step_wise.c b/drivers/thermal/gov_step_wise.c index 2ae7198d3067..12acb12aac50 100644 --- a/drivers/thermal/gov_step_wise.c +++ b/drivers/thermal/gov_step_wise.c @@ -109,7 +109,7 @@ static void update_passive_instance(struct thermal_zone_device *tz, * If value is +1, activate a passive instance. * If value is -1, deactivate a passive instance. */ - if (type == THERMAL_TRIP_PASSIVE || type == THERMAL_TRIPS_NONE) + if (type == THERMAL_TRIP_PASSIVE) tz->passive += value; } @@ -122,13 +122,8 @@ static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip) bool throttle = false; int old_target; - if (trip == THERMAL_TRIPS_NONE) { - trip_temp = tz->forced_passive; - trip_type = THERMAL_TRIPS_NONE; - } else { - tz->ops->get_trip_temp(tz, trip, &trip_temp); - tz->ops->get_trip_type(tz, trip, &trip_type); - } + tz->ops->get_trip_temp(tz, trip, &trip_temp); + tz->ops->get_trip_type(tz, trip, &trip_type); trend = get_tz_trend(tz, trip); @@ -189,9 +184,6 @@ static int step_wise_throttle(struct thermal_zone_device *tz, int trip) thermal_zone_trip_update(tz, trip); - if (tz->forced_passive) - thermal_zone_trip_update(tz, THERMAL_TRIPS_NONE); - mutex_lock(&tz->lock); list_for_each_entry(instance, &tz->thermal_instances, tz_node) diff --git a/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c b/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c index 6e479deff76b..d1248ba943a4 100644 --- a/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c +++ b/drivers/thermal/intel/int340x_thermal/int340x_thermal_zone.c @@ -146,12 +146,18 @@ static int int340x_thermal_get_trip_hyst(struct thermal_zone_device *zone, return 0; } +static void int340x_thermal_critical(struct thermal_zone_device *zone) +{ + dev_dbg(&zone->device, "%s: critical temperature reached\n", zone->type); +} + static struct thermal_zone_device_ops int340x_thermal_zone_ops = { .get_temp = int340x_thermal_get_zone_temp, .get_trip_temp = int340x_thermal_get_trip_temp, .get_trip_type = int340x_thermal_get_trip_type, .set_trip_temp = int340x_thermal_set_trip_temp, .get_trip_hyst = int340x_thermal_get_trip_hyst, + .critical = int340x_thermal_critical, }; static int int340x_thermal_get_trip_config(acpi_handle handle, char *name, diff --git a/drivers/thermal/intel/intel_pch_thermal.c b/drivers/thermal/intel/intel_pch_thermal.c index 41723c6c6c0c..527c91f5960b 100644 --- a/drivers/thermal/intel/intel_pch_thermal.c +++ b/drivers/thermal/intel/intel_pch_thermal.c @@ -326,10 +326,16 @@ static int pch_get_trip_temp(struct thermal_zone_device *tzd, int trip, int *tem return 0; } +static void pch_critical(struct thermal_zone_device *tzd) +{ + dev_dbg(&tzd->device, "%s: critical temperature reached\n", tzd->type); +} + static struct thermal_zone_device_ops tzd_ops = { .get_temp = pch_thermal_get_temp, .get_trip_type = pch_get_trip_type, .get_trip_temp = pch_get_trip_temp, + .critical = pch_critical, }; enum board_ids { diff --git a/drivers/thermal/khadas_mcu_fan.c b/drivers/thermal/khadas_mcu_fan.c index 9eadd2d6413e..d35e5313bea4 100644 --- a/drivers/thermal/khadas_mcu_fan.c +++ b/drivers/thermal/khadas_mcu_fan.c @@ -100,7 +100,6 @@ static int khadas_mcu_fan_probe(struct platform_device *pdev) return ret; } ctx->cdev = cdev; - thermal_cdev_update(cdev); return 0; } diff --git a/drivers/thermal/qcom/Kconfig b/drivers/thermal/qcom/Kconfig index aa9c1d80fae4..8d5ac2df26dc 100644 --- a/drivers/thermal/qcom/Kconfig +++ b/drivers/thermal/qcom/Kconfig @@ -10,6 +10,17 @@ config QCOM_TSENS Also able to set threshold temperature for both hot and cold and update when a threshold is reached. +config QCOM_SPMI_ADC_TM5 + tristate "Qualcomm SPMI PMIC Thermal Monitor ADC5" + depends on OF && SPMI && IIO + select REGMAP_SPMI + select QCOM_VADC_COMMON + help + This enables the thermal driver for the ADC thermal monitoring + device. It shows up as a thermal zone with multiple trip points. + Thermal client sets threshold temperature for both warm and cool and + gets updated when a threshold is reached. + config QCOM_SPMI_TEMP_ALARM tristate "Qualcomm SPMI PMIC Temperature Alarm" depends on OF && SPMI && IIO diff --git a/drivers/thermal/qcom/Makefile b/drivers/thermal/qcom/Makefile index ec86eef7f6a6..252ea7d9da0b 100644 --- a/drivers/thermal/qcom/Makefile +++ b/drivers/thermal/qcom/Makefile @@ -3,4 +3,5 @@ obj-$(CONFIG_QCOM_TSENS) += qcom_tsens.o qcom_tsens-y += tsens.o tsens-v2.o tsens-v1.o tsens-v0_1.o \ tsens-8960.o +obj-$(CONFIG_QCOM_SPMI_ADC_TM5) += qcom-spmi-adc-tm5.o obj-$(CONFIG_QCOM_SPMI_TEMP_ALARM) += qcom-spmi-temp-alarm.o diff --git a/drivers/thermal/qcom/qcom-spmi-adc-tm5.c b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c new file mode 100644 index 000000000000..b460b56e981c --- /dev/null +++ b/drivers/thermal/qcom/qcom-spmi-adc-tm5.c @@ -0,0 +1,623 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2020 Linaro Limited + * + * Based on original driver: + * Copyright (c) 2012-2020, The Linux Foundation. All rights reserved. + */ +#include <linux/bitfield.h> +#include <linux/iio/adc/qcom-vadc-common.h> +#include <linux/iio/consumer.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/thermal.h> + +/* + * Thermal monitoring block consists of 8 (ADC_TM5_NUM_CHANNELS) channels. Each + * channel is programmed to use one of ADC channels for voltage comparison. + * Voltages are programmed using ADC codes, so we have to convert temp to + * voltage and then to ADC code value. + * + * Configuration of TM channels must match configuration of corresponding ADC + * channels. + */ + +#define ADC5_MAX_CHANNEL 0xc0 +#define ADC_TM5_NUM_CHANNELS 8 + +#define ADC_TM5_STATUS_LOW 0x0a + +#define ADC_TM5_STATUS_HIGH 0x0b + +#define ADC_TM5_NUM_BTM 0x0f + +#define ADC_TM5_ADC_DIG_PARAM 0x42 + +#define ADC_TM5_FAST_AVG_CTL (ADC_TM5_ADC_DIG_PARAM + 1) +#define ADC_TM5_FAST_AVG_EN BIT(7) + +#define ADC_TM5_MEAS_INTERVAL_CTL (ADC_TM5_ADC_DIG_PARAM + 2) +#define ADC_TM5_TIMER1 3 /* 3.9ms */ + +#define ADC_TM5_MEAS_INTERVAL_CTL2 (ADC_TM5_ADC_DIG_PARAM + 3) +#define ADC_TM5_MEAS_INTERVAL_CTL2_MASK 0xf0 +#define ADC_TM5_TIMER2 10 /* 1 second */ +#define ADC_TM5_MEAS_INTERVAL_CTL3_MASK 0xf +#define ADC_TM5_TIMER3 4 /* 4 second */ + +#define ADC_TM_EN_CTL1 0x46 +#define ADC_TM_EN BIT(7) +#define ADC_TM_CONV_REQ 0x47 +#define ADC_TM_CONV_REQ_EN BIT(7) + +#define ADC_TM5_M_CHAN_BASE 0x60 + +#define ADC_TM5_M_ADC_CH_SEL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 0) +#define ADC_TM5_M_LOW_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 1) +#define ADC_TM5_M_LOW_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 2) +#define ADC_TM5_M_HIGH_THR0(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 3) +#define ADC_TM5_M_HIGH_THR1(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 4) +#define ADC_TM5_M_MEAS_INTERVAL_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 5) +#define ADC_TM5_M_CTL(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 6) +#define ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK 0xf +#define ADC_TM5_M_CTL_CAL_SEL_MASK 0x30 +#define ADC_TM5_M_CTL_CAL_VAL 0x40 +#define ADC_TM5_M_EN(n) (ADC_TM5_M_CHAN_BASE + ((n) * 8) + 7) +#define ADC_TM5_M_MEAS_EN BIT(7) +#define ADC_TM5_M_HIGH_THR_INT_EN BIT(1) +#define ADC_TM5_M_LOW_THR_INT_EN BIT(0) + +enum adc5_timer_select { + ADC5_TIMER_SEL_1 = 0, + ADC5_TIMER_SEL_2, + ADC5_TIMER_SEL_3, + ADC5_TIMER_SEL_NONE, +}; + +struct adc_tm5_data { + const u32 full_scale_code_volt; + unsigned int *decimation; + unsigned int *hw_settle; +}; + +enum adc_tm5_cal_method { + ADC_TM5_NO_CAL = 0, + ADC_TM5_RATIOMETRIC_CAL, + ADC_TM5_ABSOLUTE_CAL +}; + +struct adc_tm5_chip; + +/** + * struct adc_tm5_channel - ADC Thermal Monitoring channel data. + * @channel: channel number. + * @adc_channel: corresponding ADC channel number. + * @cal_method: calibration method. + * @prescale: channel scaling performed on the input signal. + * @hw_settle_time: the time between AMUX being configured and the + * start of conversion. + * @iio: IIO channel instance used by this channel. + * @chip: ADC TM chip instance. + * @tzd: thermal zone device used by this channel. + */ +struct adc_tm5_channel { + unsigned int channel; + unsigned int adc_channel; + enum adc_tm5_cal_method cal_method; + unsigned int prescale; + unsigned int hw_settle_time; + struct iio_channel *iio; + struct adc_tm5_chip *chip; + struct thermal_zone_device *tzd; +}; + +/** + * struct adc_tm5_chip - ADC Thermal Monitoring properties + * @regmap: SPMI ADC5 Thermal Monitoring peripheral register map field. + * @dev: SPMI ADC5 device. + * @data: software configuration data. + * @channels: array of ADC TM channel data. + * @nchannels: amount of channels defined/allocated + * @decimation: sampling rate supported for the channel. + * @avg_samples: ability to provide single result from the ADC + * that is an average of multiple measurements. + * @base: base address of TM registers. + */ +struct adc_tm5_chip { + struct regmap *regmap; + struct device *dev; + const struct adc_tm5_data *data; + struct adc_tm5_channel *channels; + unsigned int nchannels; + unsigned int decimation; + unsigned int avg_samples; + u16 base; +}; + +static const struct adc_tm5_data adc_tm5_data_pmic = { + .full_scale_code_volt = 0x70e4, + .decimation = (unsigned int []) { 250, 420, 840 }, + .hw_settle = (unsigned int []) { 15, 100, 200, 300, 400, 500, 600, 700, + 1000, 2000, 4000, 8000, 16000, 32000, + 64000, 128000 }, +}; + +static int adc_tm5_read(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len) +{ + return regmap_bulk_read(adc_tm->regmap, adc_tm->base + offset, data, len); +} + +static int adc_tm5_write(struct adc_tm5_chip *adc_tm, u16 offset, u8 *data, int len) +{ + return regmap_bulk_write(adc_tm->regmap, adc_tm->base + offset, data, len); +} + +static int adc_tm5_reg_update(struct adc_tm5_chip *adc_tm, u16 offset, u8 mask, u8 val) +{ + return regmap_write_bits(adc_tm->regmap, adc_tm->base + offset, mask, val); +} + +static irqreturn_t adc_tm5_isr(int irq, void *data) +{ + struct adc_tm5_chip *chip = data; + u8 status_low, status_high, ctl; + int ret, i; + + ret = adc_tm5_read(chip, ADC_TM5_STATUS_LOW, &status_low, sizeof(status_low)); + if (unlikely(ret)) { + dev_err(chip->dev, "read status low failed: %d\n", ret); + return IRQ_HANDLED; + } + + ret = adc_tm5_read(chip, ADC_TM5_STATUS_HIGH, &status_high, sizeof(status_high)); + if (unlikely(ret)) { + dev_err(chip->dev, "read status high failed: %d\n", ret); + return IRQ_HANDLED; + } + + for (i = 0; i < chip->nchannels; i++) { + bool upper_set = false, lower_set = false; + unsigned int ch = chip->channels[i].channel; + + /* No TZD, we warned at the boot time */ + if (!chip->channels[i].tzd) + continue; + + ret = adc_tm5_read(chip, ADC_TM5_M_EN(ch), &ctl, sizeof(ctl)); + if (unlikely(ret)) { + dev_err(chip->dev, "ctl read failed: %d, channel %d\n", ret, i); + continue; + } + + if (!(ctl & ADC_TM5_M_MEAS_EN)) + continue; + + lower_set = (status_low & BIT(ch)) && + (ctl & ADC_TM5_M_LOW_THR_INT_EN); + + upper_set = (status_high & BIT(ch)) && + (ctl & ADC_TM5_M_HIGH_THR_INT_EN); + + if (upper_set || lower_set) + thermal_zone_device_update(chip->channels[i].tzd, + THERMAL_EVENT_UNSPECIFIED); + } + + return IRQ_HANDLED; +} + +static int adc_tm5_get_temp(void *data, int *temp) +{ + struct adc_tm5_channel *channel = data; + int ret; + + if (!channel || !channel->iio) + return -EINVAL; + + ret = iio_read_channel_processed(channel->iio, temp); + if (ret < 0) + return ret; + + if (ret != IIO_VAL_INT) + return -EINVAL; + + return 0; +} + +static int adc_tm5_disable_channel(struct adc_tm5_channel *channel) +{ + struct adc_tm5_chip *chip = channel->chip; + unsigned int reg = ADC_TM5_M_EN(channel->channel); + + return adc_tm5_reg_update(chip, reg, + ADC_TM5_M_MEAS_EN | + ADC_TM5_M_HIGH_THR_INT_EN | + ADC_TM5_M_LOW_THR_INT_EN, + 0); +} + +static int adc_tm5_enable(struct adc_tm5_chip *chip) +{ + int ret; + u8 data; + + data = ADC_TM_EN; + ret = adc_tm5_write(chip, ADC_TM_EN_CTL1, &data, sizeof(data)); + if (ret < 0) { + dev_err(chip->dev, "adc-tm enable failed\n"); + return ret; + } + + data = ADC_TM_CONV_REQ_EN; + ret = adc_tm5_write(chip, ADC_TM_CONV_REQ, &data, sizeof(data)); + if (ret < 0) { + dev_err(chip->dev, "adc-tm request conversion failed\n"); + return ret; + } + + return 0; +} + +static int adc_tm5_configure(struct adc_tm5_channel *channel, int low, int high) +{ + struct adc_tm5_chip *chip = channel->chip; + u8 buf[8]; + u16 reg = ADC_TM5_M_ADC_CH_SEL_CTL(channel->channel); + int ret; + + ret = adc_tm5_read(chip, reg, buf, sizeof(buf)); + if (ret) { + dev_err(chip->dev, "channel %d params read failed: %d\n", channel->channel, ret); + return ret; + } + + buf[0] = channel->adc_channel; + + /* High temperature corresponds to low voltage threshold */ + if (high != INT_MAX) { + u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale, + chip->data->full_scale_code_volt, high); + + buf[1] = adc_code & 0xff; + buf[2] = adc_code >> 8; + buf[7] |= ADC_TM5_M_LOW_THR_INT_EN; + } else { + buf[7] &= ~ADC_TM5_M_LOW_THR_INT_EN; + } + + /* Low temperature corresponds to high voltage threshold */ + if (low != -INT_MAX) { + u16 adc_code = qcom_adc_tm5_temp_volt_scale(channel->prescale, + chip->data->full_scale_code_volt, low); + + buf[3] = adc_code & 0xff; + buf[4] = adc_code >> 8; + buf[7] |= ADC_TM5_M_HIGH_THR_INT_EN; + } else { + buf[7] &= ~ADC_TM5_M_HIGH_THR_INT_EN; + } + + buf[5] = ADC5_TIMER_SEL_2; + + /* Set calibration select, hw_settle delay */ + buf[6] &= ~ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK; + buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_HW_SETTLE_DELAY_MASK, channel->hw_settle_time); + buf[6] &= ~ADC_TM5_M_CTL_CAL_SEL_MASK; + buf[6] |= FIELD_PREP(ADC_TM5_M_CTL_CAL_SEL_MASK, channel->cal_method); + + buf[7] |= ADC_TM5_M_MEAS_EN; + + ret = adc_tm5_write(chip, reg, buf, sizeof(buf)); + if (ret) { + dev_err(chip->dev, "channel %d params write failed: %d\n", channel->channel, ret); + return ret; + } + + return adc_tm5_enable(chip); +} + +static int adc_tm5_set_trips(void *data, int low, int high) +{ + struct adc_tm5_channel *channel = data; + struct adc_tm5_chip *chip; + int ret; + + if (!channel) + return -EINVAL; + + chip = channel->chip; + dev_dbg(chip->dev, "%d:low(mdegC):%d, high(mdegC):%d\n", + channel->channel, low, high); + + if (high == INT_MAX && low <= -INT_MAX) + ret = adc_tm5_disable_channel(channel); + else + ret = adc_tm5_configure(channel, low, high); + + return ret; +} + +static struct thermal_zone_of_device_ops adc_tm5_ops = { + .get_temp = adc_tm5_get_temp, + .set_trips = adc_tm5_set_trips, +}; + +static int adc_tm5_register_tzd(struct adc_tm5_chip *adc_tm) +{ + unsigned int i; + struct thermal_zone_device *tzd; + + for (i = 0; i < adc_tm->nchannels; i++) { + adc_tm->channels[i].chip = adc_tm; + + tzd = devm_thermal_zone_of_sensor_register(adc_tm->dev, + adc_tm->channels[i].channel, + &adc_tm->channels[i], + &adc_tm5_ops); + if (IS_ERR(tzd)) { + dev_err(adc_tm->dev, "Error registering TZ zone for channel %d: %ld\n", + adc_tm->channels[i].channel, PTR_ERR(tzd)); + return PTR_ERR(tzd); + } + adc_tm->channels[i].tzd = tzd; + } + + return 0; +} + +static int adc_tm5_init(struct adc_tm5_chip *chip) +{ + u8 buf[4], channels_available; + int ret; + unsigned int i; + + ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM, + &channels_available, sizeof(channels_available)); + if (ret) { + dev_err(chip->dev, "read failed for BTM channels\n"); + return ret; + } + + for (i = 0; i < chip->nchannels; i++) { + if (chip->channels[i].channel >= channels_available) { + dev_err(chip->dev, "Invalid channel %d\n", chip->channels[i].channel); + return -EINVAL; + } + } + + buf[0] = chip->decimation; + buf[1] = chip->avg_samples | ADC_TM5_FAST_AVG_EN; + buf[2] = ADC_TM5_TIMER1; + buf[3] = FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL2_MASK, ADC_TM5_TIMER2) | + FIELD_PREP(ADC_TM5_MEAS_INTERVAL_CTL3_MASK, ADC_TM5_TIMER3); + + ret = adc_tm5_write(chip, ADC_TM5_ADC_DIG_PARAM, buf, sizeof(buf)); + if (ret) { + dev_err(chip->dev, "block write failed: %d\n", ret); + return ret; + } + + return ret; +} + +static int adc_tm5_get_dt_channel_data(struct adc_tm5_chip *adc_tm, + struct adc_tm5_channel *channel, + struct device_node *node) +{ + const char *name = node->name; + u32 chan, value, varr[2]; + int ret; + struct device *dev = adc_tm->dev; + struct of_phandle_args args; + + ret = of_property_read_u32(node, "reg", &chan); + if (ret) { + dev_err(dev, "%s: invalid channel number %d\n", name, ret); + return ret; + } + + if (chan >= ADC_TM5_NUM_CHANNELS) { + dev_err(dev, "%s: channel number too big: %d\n", name, chan); + return -EINVAL; + } + + channel->channel = chan; + + /* + * We are tied to PMIC's ADC controller, which always use single + * argument for channel number. So don't bother parsing + * #io-channel-cells, just enforce cell_count = 1. + */ + ret = of_parse_phandle_with_fixed_args(node, "io-channels", 1, 0, &args); + if (ret < 0) { + dev_err(dev, "%s: error parsing ADC channel number %d: %d\n", name, chan, ret); + return ret; + } + of_node_put(args.np); + + if (args.args_count != 1 || args.args[0] >= ADC5_MAX_CHANNEL) { + dev_err(dev, "%s: invalid ADC channel number %d\n", name, chan); + return ret; + } + channel->adc_channel = args.args[0]; + + channel->iio = devm_of_iio_channel_get_by_name(adc_tm->dev, node, NULL); + if (IS_ERR(channel->iio)) { + ret = PTR_ERR(channel->iio); + if (ret != -EPROBE_DEFER) + dev_err(dev, "%s: error getting channel: %d\n", name, ret); + return ret; + } + + ret = of_property_read_u32_array(node, "qcom,pre-scaling", varr, 2); + if (!ret) { + ret = qcom_adc5_prescaling_from_dt(varr[0], varr[1]); + if (ret < 0) { + dev_err(dev, "%s: invalid pre-scaling <%d %d>\n", + name, varr[0], varr[1]); + return ret; + } + channel->prescale = ret; + } else { + /* 1:1 prescale is index 0 */ + channel->prescale = 0; + } + + ret = of_property_read_u32(node, "qcom,hw-settle-time-us", &value); + if (!ret) { + ret = qcom_adc5_hw_settle_time_from_dt(value, adc_tm->data->hw_settle); + if (ret < 0) { + dev_err(dev, "%s invalid hw-settle-time-us %d us\n", + name, value); + return ret; + } + channel->hw_settle_time = ret; + } else { + channel->hw_settle_time = VADC_DEF_HW_SETTLE_TIME; + } + + if (of_property_read_bool(node, "qcom,ratiometric")) + channel->cal_method = ADC_TM5_RATIOMETRIC_CAL; + else + channel->cal_method = ADC_TM5_ABSOLUTE_CAL; + + return 0; +} + +static int adc_tm5_get_dt_data(struct adc_tm5_chip *adc_tm, struct device_node *node) +{ + struct adc_tm5_channel *channels; + struct device_node *child; + u32 value; + int ret; + struct device *dev = adc_tm->dev; + + adc_tm->nchannels = of_get_available_child_count(node); + if (!adc_tm->nchannels) + return -EINVAL; + + adc_tm->channels = devm_kcalloc(dev, adc_tm->nchannels, + sizeof(*adc_tm->channels), GFP_KERNEL); + if (!adc_tm->channels) + return -ENOMEM; + + channels = adc_tm->channels; + + adc_tm->data = of_device_get_match_data(dev); + if (!adc_tm->data) + adc_tm->data = &adc_tm5_data_pmic; + + ret = of_property_read_u32(node, "qcom,decimation", &value); + if (!ret) { + ret = qcom_adc5_decimation_from_dt(value, adc_tm->data->decimation); + if (ret < 0) { + dev_err(dev, "invalid decimation %d\n", value); + return ret; + } + adc_tm->decimation = ret; + } else { + adc_tm->decimation = ADC5_DECIMATION_DEFAULT; + } + + ret = of_property_read_u32(node, "qcom,avg-samples", &value); + if (!ret) { + ret = qcom_adc5_avg_samples_from_dt(value); + if (ret < 0) { + dev_err(dev, "invalid avg-samples %d\n", value); + return ret; + } + adc_tm->avg_samples = ret; + } else { + adc_tm->avg_samples = VADC_DEF_AVG_SAMPLES; + } + + for_each_available_child_of_node(node, child) { + ret = adc_tm5_get_dt_channel_data(adc_tm, channels, child); + if (ret) { + of_node_put(child); + return ret; + } + + channels++; + } + + return 0; +} + +static int adc_tm5_probe(struct platform_device *pdev) +{ + struct device_node *node = pdev->dev.of_node; + struct device *dev = &pdev->dev; + struct adc_tm5_chip *adc_tm; + struct regmap *regmap; + int ret, irq; + u32 reg; + + regmap = dev_get_regmap(dev->parent, NULL); + if (!regmap) + return -ENODEV; + + ret = of_property_read_u32(node, "reg", ®); + if (ret) + return ret; + + adc_tm = devm_kzalloc(&pdev->dev, sizeof(*adc_tm), GFP_KERNEL); + if (!adc_tm) + return -ENOMEM; + + adc_tm->regmap = regmap; + adc_tm->dev = dev; + adc_tm->base = reg; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(dev, "get_irq failed: %d\n", irq); + return irq; + } + + ret = adc_tm5_get_dt_data(adc_tm, node); + if (ret) { + dev_err(dev, "get dt data failed: %d\n", ret); + return ret; + } + + ret = adc_tm5_init(adc_tm); + if (ret) { + dev_err(dev, "adc-tm init failed\n"); + return ret; + } + + ret = adc_tm5_register_tzd(adc_tm); + if (ret) { + dev_err(dev, "tzd register failed\n"); + return ret; + } + + return devm_request_threaded_irq(dev, irq, NULL, adc_tm5_isr, + IRQF_ONESHOT, "pm-adc-tm5", adc_tm); |