| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull x86 kvm updates from Paolo Bonzini:
"x86:
- KVM currently invalidates the entirety of the page tables, not just
those for the memslot being touched, when a memslot is moved or
deleted.
This does not traditionally have particularly noticeable overhead,
but Intel's TDX will require the guest to re-accept private pages
if they are dropped from the secure EPT, which is a non starter.
Actually, the only reason why this is not already being done is a
bug which was never fully investigated and caused VM instability
with assigned GeForce GPUs, so allow userspace to opt into the new
behavior.
- Advertise AVX10.1 to userspace (effectively prep work for the
"real" AVX10 functionality that is on the horizon)
- Rework common MSR handling code to suppress errors on userspace
accesses to unsupported-but-advertised MSRs
This will allow removing (almost?) all of KVM's exemptions for
userspace access to MSRs that shouldn't exist based on the vCPU
model (the actual cleanup is non-trivial future work)
- Rework KVM's handling of x2APIC ICR, again, because AMD (x2AVIC)
splits the 64-bit value into the legacy ICR and ICR2 storage,
whereas Intel (APICv) stores the entire 64-bit value at the ICR
offset
- Fix a bug where KVM would fail to exit to userspace if one was
triggered by a fastpath exit handler
- Add fastpath handling of HLT VM-Exit to expedite re-entering the
guest when there's already a pending wake event at the time of the
exit
- Fix a WARN caused by RSM entering a nested guest from SMM with
invalid guest state, by forcing the vCPU out of guest mode prior to
signalling SHUTDOWN (the SHUTDOWN hits the VM altogether, not the
nested guest)
- Overhaul the "unprotect and retry" logic to more precisely identify
cases where retrying is actually helpful, and to harden all retry
paths against putting the guest into an infinite retry loop
- Add support for yielding, e.g. to honor NEED_RESCHED, when zapping
rmaps in the shadow MMU
- Refactor pieces of the shadow MMU related to aging SPTEs in
prepartion for adding multi generation LRU support in KVM
- Don't stuff the RSB after VM-Exit when RETPOLINE=y and AutoIBRS is
enabled, i.e. when the CPU has already flushed the RSB
- Trace the per-CPU host save area as a VMCB pointer to improve
readability and cleanup the retrieval of the SEV-ES host save area
- Remove unnecessary accounting of temporary nested VMCB related
allocations
- Set FINAL/PAGE in the page fault error code for EPT violations if
and only if the GVA is valid. If the GVA is NOT valid, there is no
guest-side page table walk and so stuffing paging related metadata
is nonsensical
- Fix a bug where KVM would incorrectly synthesize a nested VM-Exit
instead of emulating posted interrupt delivery to L2
- Add a lockdep assertion to detect unsafe accesses of vmcs12
structures
- Harden eVMCS loading against an impossible NULL pointer deref
(really truly should be impossible)
- Minor SGX fix and a cleanup
- Misc cleanups
Generic:
- Register KVM's cpuhp and syscore callbacks when enabling
virtualization in hardware, as the sole purpose of said callbacks
is to disable and re-enable virtualization as needed
- Enable virtualization when KVM is loaded, not right before the
first VM is created
Together with the previous change, this simplifies a lot the logic
of the callbacks, because their very existence implies
virtualization is enabled
- Fix a bug that results in KVM prematurely exiting to userspace for
coalesced MMIO/PIO in many cases, clean up the related code, and
add a testcase
- Fix a bug in kvm_clear_guest() where it would trigger a buffer
overflow _if_ the gpa+len crosses a page boundary, which thankfully
is guaranteed to not happen in the current code base. Add WARNs in
more helpers that read/write guest memory to detect similar bugs
Selftests:
- Fix a goof that caused some Hyper-V tests to be skipped when run on
bare metal, i.e. NOT in a VM
- Add a regression test for KVM's handling of SHUTDOWN for an SEV-ES
guest
- Explicitly include one-off assets in .gitignore. Past Sean was
completely wrong about not being able to detect missing .gitignore
entries
- Verify userspace single-stepping works when KVM happens to handle a
VM-Exit in its fastpath
- Misc cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
Documentation: KVM: fix warning in "make htmldocs"
s390: Enable KVM_S390_UCONTROL config in debug_defconfig
selftests: kvm: s390: Add VM run test case
KVM: SVM: let alternatives handle the cases when RSB filling is required
KVM: VMX: Set PFERR_GUEST_{FINAL,PAGE}_MASK if and only if the GVA is valid
KVM: x86/mmu: Use KVM_PAGES_PER_HPAGE() instead of an open coded equivalent
KVM: x86/mmu: Add KVM_RMAP_MANY to replace open coded '1' and '1ul' literals
KVM: x86/mmu: Fold mmu_spte_age() into kvm_rmap_age_gfn_range()
KVM: x86/mmu: Morph kvm_handle_gfn_range() into an aging specific helper
KVM: x86/mmu: Honor NEED_RESCHED when zapping rmaps and blocking is allowed
KVM: x86/mmu: Add a helper to walk and zap rmaps for a memslot
KVM: x86/mmu: Plumb a @can_yield parameter into __walk_slot_rmaps()
KVM: x86/mmu: Move walk_slot_rmaps() up near for_each_slot_rmap_range()
KVM: x86/mmu: WARN on MMIO cache hit when emulating write-protected gfn
KVM: x86/mmu: Detect if unprotect will do anything based on invalid_list
KVM: x86/mmu: Subsume kvm_mmu_unprotect_page() into the and_retry() version
KVM: x86: Rename reexecute_instruction()=>kvm_unprotect_and_retry_on_failure()
KVM: x86: Update retry protection fields when forcing retry on emulation failure
KVM: x86: Apply retry protection to "unprotect on failure" path
KVM: x86: Check EMULTYPE_WRITE_PF_TO_SP before unprotecting gfn
...
|
|
Introduce the quirk KVM_X86_QUIRK_SLOT_ZAP_ALL to allow users to select
KVM's behavior when a memslot is moved or deleted for KVM_X86_DEFAULT_VM
VMs. Make sure KVM behave as if the quirk is always disabled for
non-KVM_X86_DEFAULT_VM VMs.
The KVM_X86_QUIRK_SLOT_ZAP_ALL quirk offers two behavior options:
- when enabled: Invalidate/zap all SPTEs ("zap-all"),
- when disabled: Precisely zap only the leaf SPTEs within the range of the
moving/deleting memory slot ("zap-slot-leafs-only").
"zap-all" is today's KVM behavior to work around a bug [1] where the
changing the zapping behavior of memslot move/deletion would cause VM
instability for VMs with an Nvidia GPU assigned; while
"zap-slot-leafs-only" allows for more precise zapping of SPTEs within the
memory slot range, improving performance in certain scenarios [2], and
meeting the functional requirements for TDX.
Previous attempts to select "zap-slot-leafs-only" include a per-VM
capability approach [3] (which was not preferred because the root cause of
the bug remained unidentified) and a per-memslot flag approach [4]. Sean
and Paolo finally recommended the implementation of this quirk and
explained that it's the least bad option [5].
By default, the quirk is enabled on KVM_X86_DEFAULT_VM VMs to use
"zap-all". Users have the option to disable the quirk to select
"zap-slot-leafs-only" for specific KVM_X86_DEFAULT_VM VMs that are
unaffected by this bug.
For non-KVM_X86_DEFAULT_VM VMs, the "zap-slot-leafs-only" behavior is
always selected without user's opt-in, regardless of if the user opts for
"zap-all".
This is because it is assumed until proven otherwise that non-
KVM_X86_DEFAULT_VM VMs will not be exposed to the bug [1], and most
importantly, it's because TDX must have "zap-slot-leafs-only" always
selected. In TDX's case a memslot's GPA range can be a mixture of "private"
or "shared" memory. Shared is roughly analogous to how EPT is handled for
normal VMs, but private GPAs need lots of special treatment:
1) "zap-all" would require to zap private root page or non-leaf entries or
at least leaf-entries beyond the deleting memslot scope. However, TDX
demands that the root page of the private page table remains unchanged,
with leaf entries being zapped before non-leaf entries, and any dropped
private guest pages must be re-accepted by the guest.
2) if "zap-all" zaps only shared page tables, it would result in private
pages still being mapped when the memslot is gone. This may affect even
other processes if later the gmem fd was whole punched, causing the
pages being freed on the host while still mapped in the TD, because
there's no pgoff to the gfn information to zap the private page table
after memslot is gone.
So, simply go "zap-slot-leafs-only" as if the quirk is always disabled for
non-KVM_X86_DEFAULT_VM VMs to avoid manual opt-in for every VM type [6] or
complicating quirk disabling interface (current quirk disabling interface
is limited, no way to query quirks, or force them to be disabled).
Add a new function kvm_mmu_zap_memslot_leafs() to implement
"zap-slot-leafs-only". This function does not call kvm_unmap_gfn_range(),
bypassing special handling to APIC_ACCESS_PAGE_PRIVATE_MEMSLOT, as
1) The APIC_ACCESS_PAGE_PRIVATE_MEMSLOT cannot be created by users, nor can
it be moved. It is only deleted by KVM when APICv is permanently
inhibited.
2) kvm_vcpu_reload_apic_access_page() effectively does nothing when
APIC_ACCESS_PAGE_PRIVATE_MEMSLOT is deleted.
3) Avoid making all cpus request of KVM_REQ_APIC_PAGE_RELOAD can save on
costly IPIs.
Suggested-by: Kai Huang <kai.huang@intel.com>
Suggested-by: Sean Christopherson <seanjc@google.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://patchwork.kernel.org/project/kvm/patch/20190205210137.1377-11-sean.j.christopherson@intel.com [1]
Link: https://patchwork.kernel.org/project/kvm/patch/20190205210137.1377-11-sean.j.christopherson@intel.com/#25054908 [2]
Link: https://lore.kernel.org/kvm/20200713190649.GE29725@linux.intel.com/T/#mabc0119583dacf621025e9d873c85f4fbaa66d5c [3]
Link: https://lore.kernel.org/all/20240515005952.3410568-3-rick.p.edgecombe@intel.com [4]
Link: https://lore.kernel.org/all/7df9032d-83e4-46a1-ab29-6c7973a2ab0b@redhat.com [5]
Link: https://lore.kernel.org/all/ZnGa550k46ow2N3L@google.com [6]
Co-developed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Message-ID: <20240703021043.13881-1-yan.y.zhao@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add a new .note section containing type, size, offset and flags of every
xfeature that is present.
This information will be used by debuggers to understand the XSAVE layout of
the machine where the core file has been dumped, and to read XSAVE registers,
especially during cross-platform debugging.
The XSAVE layouts of modern AMD and Intel CPUs differ, especially since
Memory Protection Keys and the AVX-512 features have been inculcated into
the AMD CPUs.
Since AMD never adopted (and hence never left room in the XSAVE layout for)
the Intel MPX feature, tools like GDB had assumed a fixed XSAVE layout
matching that of Intel (based on the XCR0 mask).
Hence, core dumps from AMD CPUs didn't match the known size for the XCR0 mask.
This resulted in GDB and other tools not being able to access the values of
the AVX-512 and PKRU registers on AMD CPUs.
To solve this, an interim solution has been accepted into GDB, and is already
a part of GDB 14, see
https://sourceware.org/pipermail/gdb-patches/2023-March/198081.html.
But it depends on heuristics based on the total XSAVE register set size
and the XCR0 mask to infer the layouts of the various register blocks
for core dumps, and hence, is not a foolproof mechanism to determine the
layout of the XSAVE area.
Therefore, add a new core dump note in order to allow GDB/LLDB and other
relevant tools to determine the layout of the XSAVE area of the machine where
the corefile was dumped.
The new core dump note (which is being proposed as a per-process .note
section), NT_X86_XSAVE_LAYOUT (0x205) contains an array of structures.
Each structure describes an individual extended feature containing
offset, size and flags in this format:
struct x86_xfeat_component {
u32 type;
u32 size;
u32 offset;
u32 flags;
};
and in an independent manner, allowing for future extensions without depending
on hw arch specifics like CPUID etc.
[ bp: Massage commit message, zap trailing whitespace. ]
Co-developed-by: Jini Susan George <jinisusan.george@amd.com>
Signed-off-by: Jini Susan George <jinisusan.george@amd.com>
Co-developed-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Vignesh Balasubramanian <vigbalas@amd.com>
Link: https://lore.kernel.org/r/20240725161017.112111-2-vigbalas@amd.com
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Initial infrastructure for shadow stage-2 MMUs, as part of nested
virtualization enablement
- Support for userspace changes to the guest CTR_EL0 value, enabling
(in part) migration of VMs between heterogenous hardware
- Fixes + improvements to pKVM's FF-A proxy, adding support for v1.1
of the protocol
- FPSIMD/SVE support for nested, including merged trap configuration
and exception routing
- New command-line parameter to control the WFx trap behavior under
KVM
- Introduce kCFI hardening in the EL2 hypervisor
- Fixes + cleanups for handling presence/absence of FEAT_TCRX
- Miscellaneous fixes + documentation updates
LoongArch:
- Add paravirt steal time support
- Add support for KVM_DIRTY_LOG_INITIALLY_SET
- Add perf kvm-stat support for loongarch
RISC-V:
- Redirect AMO load/store access fault traps to guest
- perf kvm stat support
- Use guest files for IMSIC virtualization, when available
s390:
- Assortment of tiny fixes which are not time critical
x86:
- Fixes for Xen emulation
- Add a global struct to consolidate tracking of host values, e.g.
EFER
- Add KVM_CAP_X86_APIC_BUS_CYCLES_NS to allow configuring the
effective APIC bus frequency, because TDX
- Print the name of the APICv/AVIC inhibits in the relevant
tracepoint
- Clean up KVM's handling of vendor specific emulation to
consistently act on "compatible with Intel/AMD", versus checking
for a specific vendor
- Drop MTRR virtualization, and instead always honor guest PAT on
CPUs that support self-snoop
- Update to the newfangled Intel CPU FMS infrastructure
- Don't advertise IA32_PERF_GLOBAL_OVF_CTRL as an MSR-to-be-saved, as
it reads '0' and writes from userspace are ignored
- Misc cleanups
x86 - MMU:
- Small cleanups, renames and refactoring extracted from the upcoming
Intel TDX support
- Don't allocate kvm_mmu_page.shadowed_translation for shadow pages
that can't hold leafs SPTEs
- Unconditionally drop mmu_lock when allocating TDP MMU page tables
for eager page splitting, to avoid stalling vCPUs when splitting
huge pages
- Bug the VM instead of simply warning if KVM tries to split a SPTE
that is non-present or not-huge. KVM is guaranteed to end up in a
broken state because the callers fully expect a valid SPTE, it's
all but dangerous to let more MMU changes happen afterwards
x86 - AMD:
- Make per-CPU save_area allocations NUMA-aware
- Force sev_es_host_save_area() to be inlined to avoid calling into
an instrumentable function from noinstr code
- Base support for running SEV-SNP guests. API-wise, this includes a
new KVM_X86_SNP_VM type, encrypting/measure the initial image into
guest memory, and finalizing it before launching it. Internally,
there are some gmem/mmu hooks needed to prepare gmem-allocated
pages before mapping them into guest private memory ranges
This includes basic support for attestation guest requests, enough
to say that KVM supports the GHCB 2.0 specification
There is no support yet for loading into the firmware those signing
keys to be used for attestation requests, and therefore no need yet
for the host to provide certificate data for those keys.
To support fetching certificate data from userspace, a new KVM exit
type will be needed to handle fetching the certificate from
userspace.
An attempt to define a new KVM_EXIT_COCO / KVM_EXIT_COCO_REQ_CERTS
exit type to handle this was introduced in v1 of this patchset, but
is still being discussed by community, so for now this patchset
only implements a stub version of SNP Extended Guest Requests that
does not provide certificate data
x86 - Intel:
- Remove an unnecessary EPT TLB flush when enabling hardware
- Fix a series of bugs that cause KVM to fail to detect nested
pending posted interrupts as valid wake eents for a vCPU executing
HLT in L2 (with HLT-exiting disable by L1)
- KVM: x86: Suppress MMIO that is triggered during task switch
emulation
Explicitly suppress userspace emulated MMIO exits that are
triggered when emulating a task switch as KVM doesn't support
userspace MMIO during complex (multi-step) emulation
Silently ignoring the exit request can result in the
WARN_ON_ONCE(vcpu->mmio_needed) firing if KVM exits to userspace
for some other reason prior to purging mmio_needed
See commit 0dc902267cb3 ("KVM: x86: Suppress pending MMIO write
exits if emulator detects exception") for more details on KVM's
limitations with respect to emulated MMIO during complex emulator
flows
Generic:
- Rename the AS_UNMOVABLE flag that was introduced for KVM to
AS_INACCESSIBLE, because the special casing needed by these pages
is not due to just unmovability (and in fact they are only
unmovable because the CPU cannot access them)
- New ioctl to populate the KVM page tables in advance, which is
useful to mitigate KVM page faults during guest boot or after live
migration. The code will also be used by TDX, but (probably) not
through the ioctl
- Enable halt poll shrinking by default, as Intel found it to be a
clear win
- Setup empty IRQ routing when creating a VM to avoid having to
synchronize SRCU when creating a split IRQCHIP on x86
- Rework the sched_in/out() paths to replace kvm_arch_sched_in() with
a flag that arch code can use for hooking both sched_in() and
sched_out()
- Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace
detect bugs
- Mark a vCPU as preempted if and only if it's scheduled out while in
the KVM_RUN loop, e.g. to avoid marking it preempted and thus
writing guest memory when retrieving guest state during live
migration blackout
Selftests:
- Remove dead code in the memslot modification stress test
- Treat "branch instructions retired" as supported on all AMD Family
17h+ CPUs
- Print the guest pseudo-RNG seed only when it changes, to avoid
spamming the log for tests that create lots of VMs
- Make the PMU counters test less flaky when counting LLC cache
misses by doing CLFLUSH{OPT} in every loop iteration"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
crypto: ccp: Add the SNP_VLEK_LOAD command
KVM: x86/pmu: Add kvm_pmu_call() to simplify static calls of kvm_pmu_ops
KVM: x86: Introduce kvm_x86_call() to simplify static calls of kvm_x86_ops
KVM: x86: Replace static_call_cond() with static_call()
KVM: SEV: Provide support for SNP_EXTENDED_GUEST_REQUEST NAE event
x86/sev: Move sev_guest.h into common SEV header
KVM: SEV: Provide support for SNP_GUEST_REQUEST NAE event
KVM: x86: Suppress MMIO that is triggered during task switch emulation
KVM: x86/mmu: Clean up make_huge_page_split_spte() definition and intro
KVM: x86/mmu: Bug the VM if KVM tries to split a !hugepage SPTE
KVM: selftests: x86: Add test for KVM_PRE_FAULT_MEMORY
KVM: x86: Implement kvm_arch_vcpu_pre_fault_memory()
KVM: x86/mmu: Make kvm_mmu_do_page_fault() return mapped level
KVM: x86/mmu: Account pf_{fixed,emulate,spurious} in callers of "do page fault"
KVM: x86/mmu: Bump pf_taken stat only in the "real" page fault handler
KVM: Add KVM_PRE_FAULT_MEMORY vcpu ioctl to pre-populate guest memory
KVM: Document KVM_PRE_FAULT_MEMORY ioctl
mm, virt: merge AS_UNMOVABLE and AS_INACCESSIBLE
perf kvm: Add kvm-stat for loongarch64
LoongArch: KVM: Add PV steal time support in guest side
...
|
|
KVM x86 misc changes for 6.11
- Add a global struct to consolidate tracking of host values, e.g. EFER, and
move "shadow_phys_bits" into the structure as "maxphyaddr".
- Add KVM_CAP_X86_APIC_BUS_CYCLES_NS to allow configuring the effective APIC
bus frequency, because TDX.
- Print the name of the APICv/AVIC inhibits in the relevant tracepoint.
- Clean up KVM's handling of vendor specific emulation to consistently act on
"compatible with Intel/AMD", versus checking for a specific vendor.
- Misc cleanups
|
|
When a vCPU is interrupted by a signal while running a nested guest,
KVM will exit to userspace with L2 state. However, userspace has no
way to know whether it sees L1 or L2 state (besides calling
KVM_GET_STATS_FD, which does not have a stable ABI).
This causes multiple problems:
The simplest one is L2 state corruption when userspace marks the sregs
as dirty. See this mailing list thread [1] for a complete discussion.
Another problem is that if userspace decides to continue by emulating
instructions, it will unknowingly emulate with L2 state as if L1
doesn't exist, which can be considered a weird guest escape.
Introduce a new flag, KVM_RUN_X86_GUEST_MODE, in the kvm_run data
structure, which is set when the vCPU exited while running a nested
guest. Also introduce a new capability, KVM_CAP_X86_GUEST_MODE, to
advertise the functionality to userspace.
[1] https://lore.kernel.org/kvm/20240416123558.212040-1-julian.stecklina@cyberus-technology.de/T/#m280aadcb2e10ae02c191a7dc4ed4b711a74b1f55
Signed-off-by: Thomas Prescher <thomas.prescher@cyberus-technology.de>
Signed-off-by: Julian Stecklina <julian.stecklina@cyberus-technology.de>
Link: https://lore.kernel.org/r/20240508132502.184428-1-julian.stecklina@cyberus-technology.de
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The SVSM Calling Area (CA) is used to communicate between Linux and the
SVSM. Since the firmware supplied CA for the BSP is likely to be in
reserved memory, switch off that CA to a kernel provided CA so that access
and use of the CA is available during boot. The CA switch is done using
the SVSM core protocol SVSM_CORE_REMAP_CA call.
An SVSM call is executed by filling out the SVSM CA and setting the proper
register state as documented by the SVSM protocol. The SVSM is invoked by
by requesting the hypervisor to run VMPL0.
Once it is safe to allocate/reserve memory, allocate a CA for each CPU.
After allocating the new CAs, the BSP will switch from the boot CA to the
per-CPU CA. The CA for an AP is identified to the SVSM when creating the
VMSA in preparation for booting the AP.
[ bp: Heavily simplify svsm_issue_call() asm, other touchups. ]
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/fa8021130bcc3bcf14d722a25548cb0cdf325456.1717600736.git.thomas.lendacky@amd.com
|
|
Add a KVM_SEV_SNP_LAUNCH_FINISH command to finalize the cryptographic
launch digest which stores the measurement of the guest at launch time.
Also extend the existing SNP firmware data structures to support
disabling the use of Versioned Chip Endorsement Keys (VCEK) by guests as
part of this command.
While finalizing the launch flow, the code also issues the LAUNCH_UPDATE
SNP firmware commands to encrypt/measure the initial VMSA pages for each
configured vCPU, which requires setting the RMP entries for those pages
to private, so also add handling to clean up the RMP entries for these
pages whening freeing vCPUs during shutdown.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Co-developed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Harald Hoyer <harald@profian.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Message-ID: <20240501085210.2213060-8-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
A key aspect of a launching an SNP guest is initializing it with a
known/measured payload which is then encrypted into guest memory as
pre-validated private pages and then measured into the cryptographic
launch context created with KVM_SEV_SNP_LAUNCH_START so that the guest
can attest itself after booting.
Since all private pages are provided by guest_memfd, make use of the
kvm_gmem_populate() interface to handle this. The general flow is that
guest_memfd will handle allocating the pages associated with the GPA
ranges being initialized by each particular call of
KVM_SEV_SNP_LAUNCH_UPDATE, copying data from userspace into those pages,
and then the post_populate callback will do the work of setting the
RMP entries for these pages to private and issuing the SNP firmware
calls to encrypt/measure them.
For more information see the SEV-SNP specification.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Co-developed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Message-ID: <20240501085210.2213060-7-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM_SEV_SNP_LAUNCH_START begins the launch process for an SEV-SNP guest.
The command initializes a cryptographic digest context used to construct
the measurement of the guest. Other commands can then at that point be
used to load/encrypt data into the guest's initial launch image.
For more information see the SEV-SNP specification.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Co-developed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Message-ID: <20240501085210.2213060-6-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
SEV-SNP builds upon existing SEV and SEV-ES functionality while adding
new hardware-based security protection. SEV-SNP adds strong memory
encryption and integrity protection to help prevent malicious
hypervisor-based attacks such as data replay, memory re-mapping, and
more, to create an isolated execution environment.
Define a new KVM_X86_SNP_VM type which makes use of these capabilities
and extend the KVM_SEV_INIT2 ioctl to support it. Also add a basic
helper to check whether SNP is enabled and set PFERR_PRIVATE_ACCESS for
private #NPFs so they are handled appropriately by KVM MMU.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Co-developed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240501085210.2213060-5-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The GHCB protocol version may be different from one guest to the next.
Add a field to track it for each KVM instance and extend KVM_SEV_INIT2
to allow it to be configured by userspace.
Now that all SEV-ES support for GHCB protocol version 2 is in place, go
ahead and default to it when creating SEV-ES guests through the new
KVM_SEV_INIT2 interface. Keep the older KVM_SEV_ES_INIT interface
restricted to GHCB protocol version 1.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-ID: <20240501071048.2208265-5-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The idea that no parameter would ever be necessary when enabling SEV or
SEV-ES for a VM was decidedly optimistic. In fact, in some sense it's
already a parameter whether SEV or SEV-ES is desired. Another possible
source of variability is the desired set of VMSA features, as that affects
the measurement of the VM's initial state and cannot be changed
arbitrarily by the hypervisor.
Create a new sub-operation for KVM_MEMORY_ENCRYPT_OP that can take a struct,
and put the new op to work by including the VMSA features as a field of the
struct. The existing KVM_SEV_INIT and KVM_SEV_ES_INIT use the full set of
supported VMSA features for backwards compatibility.
The struct also includes the usual bells and whistles for future
extensibility: a flags field that must be zero for now, and some padding
at the end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240404121327.3107131-13-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-ID: <20240404121327.3107131-11-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Compute the set of features to be stored in the VMSA when KVM is
initialized; move it from there into kvm_sev_info when SEV is initialized,
and then into the initial VMSA.
The new variable can then be used to return the set of supported features
to userspace, via the KVM_GET_DEVICE_ATTR ioctl.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-ID: <20240404121327.3107131-6-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The data structs for KVM_MEMORY_ENCRYPT_OP have different sizes for 32- and 64-bit
userspace, but they do not make any attempt to convert from one ABI to the other
when 32-bit userspace is running on 64-bit kernels. This configuration never
worked, and SEV is only for 64-bit kernels so we're not breaking ABI on 32-bit
kernels.
Fix this by adding the appropriate padding; no functional change intended
for 64-bit userspace.
Reviewed-by: Michael Roth <michael.roth@amd.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
HEAD
Guest-side KVM async #PF ABI cleanup for 6.9
Delete kvm_vcpu_pv_apf_data.enabled to fix a goof in KVM's async #PF ABI where
the enabled field pushes the size of "struct kvm_vcpu_pv_apf_data" from 64 to
68 bytes, i.e. beyond a single cache line.
The enabled field is purely a guest-side flag that Linux-as-a-guest uses to
track whether or not the guest has enabled async #PF support. The actual flag
that is passed to the host, i.e. to KVM proper, is a single bit in a synthetic
MSR, MSR_KVM_ASYNC_PF_EN, i.e. is in a location completely unrelated to the
shared kvm_vcpu_pv_apf_data structure.
Simply drop the the field and use a dedicated guest-side per-CPU variable to
fix the ABI, as opposed to fixing the documentation to match reality. KVM has
never consumed kvm_vcpu_pv_apf_data.enabled, so the odds of the ABI change
breaking anything are extremely low.
|
|
Pull kvm updates from Paolo Bonzini:
"S390:
- Changes to FPU handling came in via the main s390 pull request
- Only deliver to the guest the SCLP events that userspace has
requested
- More virtual vs physical address fixes (only a cleanup since
virtual and physical address spaces are currently the same)
- Fix selftests undefined behavior
x86:
- Fix a restriction that the guest can't program a PMU event whose
encoding matches an architectural event that isn't included in the
guest CPUID. The enumeration of an architectural event only says
that if a CPU supports an architectural event, then the event can
be programmed *using the architectural encoding*. The enumeration
does NOT say anything about the encoding when the CPU doesn't
report support the event *in general*. It might support it, and it
might support it using the same encoding that made it into the
architectural PMU spec
- Fix a variety of bugs in KVM's emulation of RDPMC (more details on
individual commits) and add a selftest to verify KVM correctly
emulates RDMPC, counter availability, and a variety of other
PMC-related behaviors that depend on guest CPUID and therefore are
easier to validate with selftests than with custom guests (aka
kvm-unit-tests)
- Zero out PMU state on AMD if the virtual PMU is disabled, it does
not cause any bug but it wastes time in various cases where KVM
would check if a PMC event needs to be synthesized
- Optimize triggering of emulated events, with a nice ~10%
performance improvement in VM-Exit microbenchmarks when a vPMU is
exposed to the guest
- Tighten the check for "PMI in guest" to reduce false positives if
an NMI arrives in the host while KVM is handling an IRQ VM-Exit
- Fix a bug where KVM would report stale/bogus exit qualification
information when exiting to userspace with an internal error exit
code
- Add a VMX flag in /proc/cpuinfo to report 5-level EPT support
- Rework TDP MMU root unload, free, and alloc to run with mmu_lock
held for read, e.g. to avoid serializing vCPUs when userspace
deletes a memslot
- Tear down TDP MMU page tables at 4KiB granularity (used to be
1GiB). KVM doesn't support yielding in the middle of processing a
zap, and 1GiB granularity resulted in multi-millisecond lags that
are quite impolite for CONFIG_PREEMPT kernels
- Allocate write-tracking metadata on-demand to avoid the memory
overhead when a kernel is built with i915 virtualization support
but the workloads use neither shadow paging nor i915 virtualization
- Explicitly initialize a variety of on-stack variables in the
emulator that triggered KMSAN false positives
- Fix the debugregs ABI for 32-bit KVM
- Rework the "force immediate exit" code so that vendor code
ultimately decides how and when to force the exit, which allowed
some optimization for both Intel and AMD
- Fix a long-standing bug where kvm_has_noapic_vcpu could be left
elevated if vCPU creation ultimately failed, causing extra
unnecessary work
- Cleanup the logic for checking if the currently loaded vCPU is
in-kernel
- Harden against underflowing the active mmu_notifier invalidation
count, so that "bad" invalidations (usually due to bugs elsehwere
in the kernel) are detected earlier and are less likely to hang the
kernel
x86 Xen emulation:
- Overlay pages can now be cached based on host virtual address,
instead of guest physical addresses. This removes the need to
reconfigure and invalidate the cache if the guest changes the gpa
but the underlying host virtual address remains the same
- When possible, use a single host TSC value when computing the
deadline for Xen timers in order to improve the accuracy of the
timer emulation
- Inject pending upcall events when the vCPU software-enables its
APIC to fix a bug where an upcall can be lost (and to follow Xen's
behavior)
- Fall back to the slow path instead of warning if "fast" IRQ
delivery of Xen events fails, e.g. if the guest has aliased xAPIC
IDs
RISC-V:
- Support exception and interrupt handling in selftests
- New self test for RISC-V architectural timer (Sstc extension)
- New extension support (Ztso, Zacas)
- Support userspace emulation of random number seed CSRs
ARM:
- Infrastructure for building KVM's trap configuration based on the
architectural features (or lack thereof) advertised in the VM's ID
registers
- Support for mapping vfio-pci BARs as Normal-NC (vaguely similar to
x86's WC) at stage-2, improving the performance of interacting with
assigned devices that can tolerate it
- Conversion of KVM's representation of LPIs to an xarray, utilized
to address serialization some of the serialization on the LPI
injection path
- Support for _architectural_ VHE-only systems, advertised through
the absence of FEAT_E2H0 in the CPU's ID register
- Miscellaneous cleanups, fixes, and spelling corrections to KVM and
selftests
LoongArch:
- Set reserved bits as zero in CPUCFG
- Start SW timer only when vcpu is blocking
- Do not restart SW timer when it is expired
- Remove unnecessary CSR register saving during enter guest
- Misc cleanups and fixes as usual
Generic:
- Clean up Kconfig by removing CONFIG_HAVE_KVM, which was basically
always true on all architectures except MIPS (where Kconfig
determines the available depending on CPU capabilities). It is
replaced either by an architecture-dependent symbol for MIPS, and
IS_ENABLED(CONFIG_KVM) everywhere else
- Factor common "select" statements in common code instead of
requiring each architecture to specify it
- Remove thoroughly obsolete APIs from the uapi headers
- Move architecture-dependent stuff to uapi/asm/kvm.h
- Always flush the async page fault workqueue when a work item is
being removed, especially during vCPU destruction, to ensure that
there are no workers running in KVM code when all references to
KVM-the-module are gone, i.e. to prevent a very unlikely
use-after-free if kvm.ko is unloaded
- Grab a reference to the VM's mm_struct in the async #PF worker
itself instead of gifting the worker a reference, so that there's
no need to remember to *conditionally* clean up after the worker
Selftests:
- Reduce boilerplate especially when utilize selftest TAP
infrastructure
- Add basic smoke tests for SEV and SEV-ES, along with a pile of
library support for handling private/encrypted/protected memory
- Fix benign bugs where tests neglect to close() guest_memfd files"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
selftests: kvm: remove meaningless assignments in Makefiles
KVM: riscv: selftests: Add Zacas extension to get-reg-list test
RISC-V: KVM: Allow Zacas extension for Guest/VM
KVM: riscv: selftests: Add Ztso extension to get-reg-list test
RISC-V: KVM: Allow Ztso extension for Guest/VM
RISC-V: KVM: Forward SEED CSR access to user space
KVM: riscv: selftests: Add sstc timer test
KVM: riscv: selftests: Change vcpu_has_ext to a common function
KVM: riscv: selftests: Add guest helper to get vcpu id
KVM: riscv: selftests: Add exception handling support
LoongArch: KVM: Remove unnecessary CSR register saving during enter guest
LoongArch: KVM: Do not restart SW timer when it is expired
LoongArch: KVM: Start SW timer only when vcpu is blocking
LoongArch: KVM: Set reserved bits as zero in CPUCFG
KVM: selftests: Explicitly close guest_memfd files in some gmem tests
KVM: x86/xen: fix recursive deadlock in timer injection
KVM: pfncache: simplify locking and make more self-contained
KVM: x86/xen: remove WARN_ON_ONCE() with false positives in evtchn delivery
KVM: x86/xen: inject vCPU upcall vector when local APIC is enabled
KVM: x86/xen: improve accuracy of Xen timers
...
|
|
There's a new conflict with Linus's upstream tree, because
in the following merge conflict resolution in <asm/coco.h>:
38b334fc767e Merge tag 'x86_sev_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Linus has resolved the conflicting placement of 'cc_mask' better
than the original commit:
1c811d403afd x86/sev: Fix position dependent variable references in startup code
... which was also done by an internal merge resolution:
2e5fc4786b7a Merge branch 'x86/sev' into x86/boot, to resolve conflicts and to pick up dependent tree
But Linus is right in 38b334fc767e, the 'cc_mask' declaration is sufficient
within the #ifdef CONFIG_ARCH_HAS_CC_PLATFORM block.
So instead of forcing Linus to do the same resolution again, merge in Linus's
tree and follow his conflict resolution.
Conflicts:
arch/x86/include/asm/coco.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 build updates from Ingo Molnar:
- Reduce <asm/bootparam.h> dependencies
- Simplify <asm/efi.h>
- Unify *_setup_data definitions into <asm/setup_data.h>
- Reduce the size of <asm/bootparam.h>
* tag 'x86-build-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Do not include <asm/bootparam.h> in several files
x86/efi: Implement arch_ima_efi_boot_mode() in source file
x86/setup: Move internal setup_data structures into setup_data.h
x86/setup: Move UAPI setup structures into setup_data.h
|
|
The early SME/SEV code parses the command line very early, in order to
decide whether or not memory encryption should be enabled, which needs
to occur even before the initial page tables are created.
This is problematic for a number of reasons:
- this early code runs from the 1:1 mapping provided by the decompressor
or firmware, which uses a different translation than the one assumed by
the linker, and so the code needs to be built in a special way;
- parsing external input while the entire kernel image is still mapped
writable is a bad idea in general, and really does not belong in
security minded code;
- the current code ignores the built-in command line entirely (although
this appears to be the case for the entire decompressor)
Given that the decompressor/EFI stub is an intrinsic part of the x86
bootable kernel image, move the command line parsing there and out of
the core kernel. This removes the need to build lib/cmdline.o in a
special way, or to use RIP-relative LEA instructions in inline asm
blocks.
This involves a new xloadflag in the setup header to indicate
that mem_encrypt=on appeared on the kernel command line.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20240227151907.387873-17-ardb+git@google.com
|
|
If the guest does not explicitly set the GPA of vcpu_info structure in
memory then, for guests with 32 vCPUs or fewer, the vcpu_info embedded
in the shared_info page may be used. As described in a previous commit,
the shared_info page is an overlay at a fixed HVA within the VMM, so in
this case it also more optimal to activate the vcpu_info cache with a
fixed HVA to avoid unnecessary invalidation if the guest memory layout
is modified.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-14-paul@xen.org
[sean: use kvm_gpc_is_{gpa,hva}_active()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The shared_info page is not guest memory as such. It is a dedicated page
allocated by the VMM and overlaid onto guest memory in a GFN chosen by the
guest and specified in the XENMEM_add_to_physmap hypercall. The guest may
even request that shared_info be moved from one GFN to another by
re-issuing that hypercall, but the HVA is never going to change.
Because the shared_info page is an overlay the memory slots need to be
updated in response to the hypercall. However, memory slot adjustment is
not atomic and, whilst all vCPUs are paused, there is still the possibility
that events may be delivered (which requires the shared_info page to be
updated) whilst the shared_info GPA is absent. The HVA is never absent
though, so it makes much more sense to use that as the basis for the
kernel's mapping.
Hence add a new KVM_XEN_ATTR_TYPE_SHARED_INFO_HVA attribute type for this
purpose and a KVM_XEN_HVM_CONFIG_SHARED_INFO_HVA flag to advertize its
availability. Don't actually advertize it yet though. That will be done in
a subsequent patch, which will also add tests for the new attribute type.
Also update the KVM API documentation with the new attribute and also fix
it up to consistently refer to 'shared_info' (with the underscore).
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lore.kernel.org/r/20240215152916.1158-13-paul@xen.org
[sean: store "hva" as a user pointer, use kvm_gpc_is_{gpa,hva}_active()]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Since all architectures (for historical reasons) have to define
struct kvm_guest_debug_arch, and since userspace has to check
KVM_CHECK_EXTENSION(KVM_CAP_SET_GUEST_DEBUG) anyway, there is
no advantage in masking the capability #define itself. Remove
the #define __KVM_HAVE_GUEST_DEBUG from architecture-specific
headers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM uses __KVM_HAVE_* symbols in the architecture-dependent uapi/asm/kvm.h to mask
unused definitions in include/uapi/linux/kvm.h. __KVM_HAVE_READONLY_MEM however
was nothing but a misguided attempt to define KVM_CAP_READONLY_MEM only on
architectures where KVM_CHECK_EXTENSION(KVM_CAP_READONLY_MEM) could possibly
return nonzero. This however does not make sense, and it prevented userspace
from supporting this architecture-independent feature without recompilation.
Therefore, these days __KVM_HAVE_READONLY_MEM does not mask anything and
is only used in virt/kvm/kvm_main.c. Userspace does not need to test it
and there should be no need for it to exist. Remove it and replace it
with a Kconfig symbol within Linux source code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Several capabilities that exist only on x86 nevertheless have their
structs defined in include/uapi/linux/kvm.h. Move them to
arch/x86/include/uapi/asm/kvm.h for cleanliness.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change uapi header uses of GENMASK to instead use the uapi/linux/bits.h bit
macros, since GENMASK is not defined in uapi headers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change uapi header uses of BIT to instead use the uapi/linux/const.h bit
macros, since BIT is not defined in uapi headers.
The PMU mask uses _BITUL since it targets a 32 bit flag field, whereas
the longmode definition is meant for a 64 bit flag field.
Cc: Sean Christophersen <seanjc@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dionna Glaze <dionnaglaze@google.com>
Message-Id: <20231207001142.3617856-1-dionnaglaze@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Refer to commit fd10cde9294f ("KVM paravirt: Add async PF initialization
to PV guest") and commit 344d9588a9df ("KVM: Add PV MSR to enable
asynchronous page faults delivery"). It turns out that at the time when
asyncpf was introduced, the purpose was defining the shared PV data 'struct
kvm_vcpu_pv_apf_data' with the size of 64 bytes. However, it made a mistake
and defined the size to 68 bytes, which faile |
