| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add check for the return value of spi_get_csgpiod() to avoid passing a NULL
pointer to gpiod_direction_output(), preventing a crash when GPIO chip
select is not used.
Fix below crash:
[ 4.251960] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 4.260762] Mem abort info:
[ 4.263556] ESR = 0x0000000096000004
[ 4.267308] EC = 0x25: DABT (current EL), IL = 32 bits
[ 4.272624] SET = 0, FnV = 0
[ 4.275681] EA = 0, S1PTW = 0
[ 4.278822] FSC = 0x04: level 0 translation fault
[ 4.283704] Data abort info:
[ 4.286583] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 4.292074] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 4.297130] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 4.302445] [0000000000000000] user address but active_mm is swapper
[ 4.308805] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
[ 4.315072] Modules linked in:
[ 4.318124] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc4-next-20241023-00008-ga20ec42c5fc1 #359
[ 4.328130] Hardware name: LS1046A QDS Board (DT)
[ 4.332832] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 4.339794] pc : gpiod_direction_output+0x34/0x5c
[ 4.344505] lr : gpiod_direction_output+0x18/0x5c
[ 4.349208] sp : ffff80008003b8f0
[ 4.352517] x29: ffff80008003b8f0 x28: 0000000000000000 x27: ffffc96bcc7e9068
[ 4.359659] x26: ffffc96bcc6e00b0 x25: ffffc96bcc598398 x24: ffff447400132810
[ 4.366800] x23: 0000000000000000 x22: 0000000011e1a300 x21: 0000000000020002
[ 4.373940] x20: 0000000000000000 x19: 0000000000000000 x18: ffffffffffffffff
[ 4.381081] x17: ffff44740016e600 x16: 0000000500000003 x15: 0000000000000007
[ 4.388221] x14: 0000000000989680 x13: 0000000000020000 x12: 000000000000001e
[ 4.395362] x11: 0044b82fa09b5a53 x10: 0000000000000019 x9 : 0000000000000008
[ 4.402502] x8 : 0000000000000002 x7 : 0000000000000007 x6 : 0000000000000000
[ 4.409641] x5 : 0000000000000200 x4 : 0000000002000000 x3 : 0000000000000000
[ 4.416781] x2 : 0000000000022202 x1 : 0000000000000000 x0 : 0000000000000000
[ 4.423921] Call trace:
[ 4.426362] gpiod_direction_output+0x34/0x5c (P)
[ 4.431067] gpiod_direction_output+0x18/0x5c (L)
[ 4.435771] dspi_setup+0x220/0x334
Fixes: 9e264f3f85a5 ("spi: Replace all spi->chip_select and spi->cs_gpiod references with function call")
Cc: stable@vger.kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241023203032.1388491-1-Frank.Li@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During boot, users sometimes observe the following warning:
[7.841431] WARNING: CPU: 4 PID: 492 at
drivers/interconnect/core.c:685 __icc_enable
(drivers/interconnect/core.c:685 (discriminator 7))
[..]
[7.841541] Call trace:
[7.841542] __icc_enable (drivers/interconnect/core.c:685 (discriminator 7))
[7.841545] icc_disable (drivers/interconnect/core.c:708)
[7.841547] geni_icc_disable (drivers/soc/qcom/qcom-geni-se.c:862)
[7.841553] spi_geni_runtime_suspend+0x3c/0x4c spi_geni_qcom
This occurs when the spi-geni driver receives an -EPROBE_DEFER error
from spi_geni_grab_gpi_chan(), causing devres to start releasing all
resources as shown below:
[7.138679] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_icc_release (8 bytes)
[7.138751] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_icc_release (8 bytes)
[7.138827] geni_spi 880000.spi: DEVRES REL ffff800081443800 pm_runtime_disable_action (16 bytes)
[7.139494] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_pm_opp_config_release (16 bytes)
[7.139512] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_spi_release_controller (8 bytes)
[7.139516] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_clk_release (16 bytes)
[7.139519] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_ioremap_release (8 bytes)
[7.139524] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_region_release (24 bytes)
[7.139527] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_kzalloc_release (22 bytes)
[7.139530] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_pinctrl_release (8 bytes)
[7.139539] geni_spi 880000.spi: DEVRES REL ffff800081443800 devm_kzalloc_release (40 bytes)
The issue here is that pm_runtime_disable_action() results in a call to
spi_geni_runtime_suspend(), which attempts to suspend the device and
disable an interconnect path that devm_icc_release() has just released.
Resolve this by calling geni_icc_get() before enabling runtime PM. This
approach ensures that when devres releases resources in reverse order,
it will start with pm_runtime_disable_action(), suspending the device,
and then proceed to free the remaining resources.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Closes: https://lore.kernel.org/r/CA+G9fYtsjFtddG8i+k-SpV8U6okL0p4zpsTiwGfNH5GUA8dWAA@mail.gmail.com
Fixes: 89e362c883c6 ("spi: geni-qcom: Undo runtime PM changes at driver exit time")
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Link: https://patch.msgid.link/20241008231615.430073-1-djakov@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The op argument is missing the colon and is not picked up by the
kerneldoc generator. Fix it to address the following build warning:
drivers/spi/spi-mtk-snfi.c:1201: warning: Function parameter or struct member 'op' not described in 'mtk_snand_is_page_ops'
Fixes: 764f1b748164 ("spi: add driver for MTK SPI NAND Flash Interface")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20241021142113.71081-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The STM32MP25 SOC has capability to behave in device mode however
missing .has_device_mode within its stm32mp25_spi_cfg structure leads
to not being able to enable the device mode.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patch.msgid.link/20241009-spi-mp25-device-fix-v1-1-8e5ca7db7838@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small set of driver specific fixes that came in since the merge
window, about half of which is fixes for correctness in the use of the
runtime PM APIs done as part of a broader cleanup"
* tag 'spi-fix-v6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: s3c64xx: fix timeout counters in flush_fifo
spi: atmel-quadspi: Fix wrong register value written to MR
spi: spi-cadence: Fix missing spi_controller_is_target() check
spi: spi-cadence: Fix pm_runtime_set_suspended() with runtime pm enabled
spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Merge series from Jinjie Ruan <ruanjinjie@huawei.com>:
Fix pm_runtime_set_suspended() with runtime pm enabled, and fix the missing
check for spi-cadence.
Jinjie Ruan (3):
spi: spi-imx: Fix pm_runtime_set_suspended() with runtime pm enabled
spi: spi-cadence: Fix pm_runtime_set_suspended() with runtime pm
enabled
spi: spi-cadence: Fix missing spi_controller_is_target() check
drivers/spi/spi-cadence.c | 8 +++++---
drivers/spi/spi-imx.c | 2 +-
2 files changed, 6 insertions(+), 4 deletions(-)
--
2.34.1
|
|
In the s3c64xx_flush_fifo() code, the loops counter is post-decremented
in the do { } while(test && loops--) condition. This means the loops is
left at the unsigned equivalent of -1 if the loop times out. The test
after will never pass as if tests for loops == 0.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Fixes: 230d42d422e7 ("spi: Add s3c64xx SPI Controller driver")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://patch.msgid.link/20240924134009.116247-2-ben.dooks@codethink.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
aq->mr should go to MR, nothing else.
Fixes: 329ca3eed4a9 ("spi: atmel-quadspi: Avoid overwriting delay register settings")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/linux-spi/20240926-macarena-wincing-7c4995487a29@thorsis.com/T/#u
Link: https://patch.msgid.link/20240926090356.105789-1-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi_controller_is_target() check is missing for pm_runtime_disable()
in cdns_spi_remove(), add it.
Fixes: b1b90514eaa3 ("spi: spi-cadence: Add support for Slave mode")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-4-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: d36ccd9f7ea4 ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is not valid to call pm_runtime_set_suspended() for devices
with runtime PM enabled because it returns -EAGAIN if it is enabled
already and working. So, call pm_runtime_disable() before to fix it.
Fixes: 43b6bf406cd0 ("spi: imx: fix runtime pm support for !CONFIG_PM")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240923040015.3009329-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Some driver specific fixes that came in during the merge window.
Lorenzo Bianconi did some extra testing on the recently added arioha
driver and found some issues, Alexander Dahl fixed some issues with
signal delays in the Atmel QSPI driver and Jinjie Ruan has been fixing
some nits with runtime PM cleanup"
* tag 'spi-fix-v6.12-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel-quadspi: Avoid overwriting delay register settings
spi: airoha: remove read cache in airoha_snand_dirmap_read()
spi: spi-fsl-lpspi: Undo runtime PM changes at driver exit time
spi: atmel-quadspi: Undo runtime PM changes at driver exit time
spi: airoha: fix airoha_snand_{write,read}_data data_len estimation
spi: airoha: fix dirmap_{read,write} operations
|
|
Previously the MR and SCR registers were just set with the supposedly
required values, from cached register values (cached reg content
initialized to zero).
All parts fixed here did not consider the current register (cache)
content, which would make future support of cs_setup, cs_hold, and
cs_inactive impossible.
Setting SCBR in atmel_qspi_setup() erases a possible DLYBS setting from
atmel_qspi_set_cs_timing(). The DLYBS setting is applied by ORing over
the current setting, without resetting the bits first. All writes to MR
did not consider possible settings of DLYCS and DLYBCT.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Fixes: f732646d0ccd ("spi: atmel-quadspi: Add support for configuring CS timing")
Link: https://patch.msgid.link/20240918082744.379610-2-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current upstream driver reports errors running mtd_oobtest kernel module
test:
root@OpenWrt:/# insmod mtd_test.ko
root@OpenWrt:/# insmod mtd_oobtest.ko dev=5
[ 7023.730584] =================================================
[ 7023.736399] mtd_oobtest: MTD device: 5
[ 7023.740160] mtd_oobtest: MTD device size 3670016, eraseblock size 131072, page size 2048, count of eraseblocks 28, pages per eraseblock 64, OOB size 128
[ 7023.753837] mtd_test: scanning for bad eraseblocks
[ 7023.758636] mtd_test: scanned 28 eraseblocks, 0 are bad
[ 7023.763861] mtd_oobtest: test 1 of 5
[ 7024.042076] mtd_oobtest: writing OOBs of whole device
[ 7024.682069] mtd_oobtest: written up to eraseblock 0
[ 7041.962077] mtd_oobtest: written 28 eraseblocks
[ 7041.966626] mtd_oobtest: verifying all eraseblocks
[ 7041.972276] mtd_oobtest: error @addr[0x0:0x0] 0xff -> 0xe diff 0xf1
[ 7041.978550] mtd_oobtest: error @addr[0x0:0x1] 0xff -> 0x10 diff 0xef
[ 7041.984932] mtd_oobtest: error @addr[0x0:0x2] 0xff -> 0x82 diff 0x7d
[ 7041.991293] mtd_oobtest: error @addr[0x0:0x3] 0xff -> 0x10 diff 0xef
[ 7041.997659] mtd_oobtest: error @addr[0x0:0x4] 0xff -> 0x0 diff 0xff
[ 7042.003942] mtd_oobtest: error @addr[0x0:0x5] 0xff -> 0x8a diff 0x75
[ 7042.010294] mtd_oobtest: error @addr[0x0:0x6] 0xff -> 0x20 diff 0xdf
[ 7042.016659] mtd_oobtest: error @addr[0x0:0x7] 0xff -> 0x1 diff 0xfe
[ 7042.022935] mtd_oobtest: error @addr[0x0:0x8] 0xff -> 0x2e diff 0xd1
[ 7042.029295] mtd_oobtest: error @addr[0x0:0x9] 0xff -> 0x40 diff 0xbf
[ 7042.035661] mtd_oobtest: error @addr[0x0:0xa] 0xff -> 0x0 diff 0xff
[ 7042.041935] mtd_oobtest: error @addr[0x0:0xb] 0xff -> 0x89 diff 0x76
[ 7042.048300] mtd_oobtest: error @addr[0x0:0xc] 0xff -> 0x82 diff 0x7d
[ 7042.054662] mtd_oobtest: error @addr[0x0:0xd] 0xff -> 0x15 diff 0xea
[ 7042.061014] mtd_oobtest: error @addr[0x0:0xe] 0xff -> 0x90 diff 0x6f
[ 7042.067380] mtd_oobtest: error @addr[0x0:0xf] 0xff -> 0x0 diff 0xff
....
[ 7432.421369] mtd_oobtest: error @addr[0x237800:0x36] 0xff -> 0x5f diff 0xa0
[ 7432.428242] mtd_oobtest: error @addr[0x237800:0x37] 0xff -> 0x21 diff 0xde
[ 7432.435118] mtd_oobtest: error: verify failed at 0x237800
[ 7432.440510] mtd_oobtest: error: too many errors
[ 7432.445053] mtd_oobtest: error -1 occurred
The above errors are due to the buggy logic in the 'read cache' available
in airoha_snand_dirmap_read() routine since there are some corner cases
where we are missing data updates. Since we do not get any read/write speed
improvement using the cache (according to the mtd_speedtest kernel
module test), in order to fix the mtd_oobtest test, remove the 'read cache'
in airoha_snand_dirmap_read routine. Now the driver is passing all the
tests available in mtd_test suite.
Fixes: a403997c1201 ("spi: airoha: add SPI-NAND Flash controller driver")
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240919-airoha-spi-fixes-v2-1-cb0f0ed9920a@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906021251.610462-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, call pm_runtime_dont_use_autosuspend() at driver exit time
to fix it.
Fixes: 4a2f83b7f780 ("spi: atmel-quadspi: add runtime pm support")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240906023956.1004440-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix data length written and read in airoha_snand_write_data and
airoha_snand_read_data routines respectively if it is bigger than
SPI_MAX_TRANSFER_SIZE.
Fixes: a403997c1201 ("spi: airoha: add SPI-NAND Flash controller driver")
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240913-airoha-spi-fixes-v1-2-de2e74ed4664@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SPI_NFI_READ_FROM_CACHE_DONE bit must be written at the end of
dirmap_read operation even if it is already set.
In the same way, SPI_NFI_LOAD_TO_CACHE_DONE bit must be written at the
end of dirmap_write operation even if it is already set.
For this reason use regmap_write_bits() instead of regmap_set_bits().
This patch fixes mtd_pagetest kernel module test.
Fixes: a403997c1201 ("spi: airoha: add SPI-NAND Flash controller driver")
Tested-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240913-airoha-spi-fixes-v1-1-de2e74ed4664@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This is quite a quiet release for SPI. The one new core feature here
is support for configuring the state of the MOSI pin when the bus is
idle, there are some devices which are very fragile in this regard
even when the chip select signal is not asserted. Otherwise we have
some new driver support, a bunch of small fixes and some general
cleanup work.
- Support for configuring the state of the MOSI pin when the the bus
is idle
- Add the Elgin JG0309-01 in spidev
- Support for Marvell xSPI, Mediatek MTK7981, Microchip PIC64GX, NXP
i.MX8ULP, and Rockchip RK3576 controllers
I also accidentally pulled in an IIO DT bindings update due to a typo
when applying the MOSI idle state patches"
* tag 'spi-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (65 commits)
spi: geni-qcom: Use devm functions to simplify code
spi: remove spi_controller_is_slave() and spi_slave_abort()
platform/olpc: olpc-xo175-ec: switch to use spi_target_abort().
spi: slave-mt27xx: switch to use target_abort
spi: spidev: switch to use spi_target_abort()
spi: slave-system-control: switch to use spi_target_abort()
spi: slave-time: switch to use spi_target_abort()
spi: switch to use spi_controller_is_target()
spi: fspi: add support for imx8ulp
spi: fspi: involve lut_num for struct nxp_fspi_devtype_data
dt-bindings: spi: nxp-fspi: add imx8ulp support
spi: spidev_fdx: Fix the wrong format specifier
spi: mxs: Switch to RUNTIME/SYSTEM_SLEEP_PM_OPS()
spi: dt-bindings: Add rockchip,rk3576-spi compatible
spi: Revert "spi: Insert the missing pci_dev_put()before return"
spi: zynq-qspi: Replace kzalloc with kmalloc for buffer allocation
spi: ppc4xx: Sort headers
spi: ppc4xx: Revert "handle irq_of_parse_and_map() errors"
spi: zynqmp-gqspi: Simplify with dev_err_probe()
spi: zynqmp-gqspi: Use devm_spi_alloc_host()
...
|
|
Two fields got removed but are still documented:
drivers/spi/spi-ep93xx.c:98: warning: Excess struct member 'dma_rx_data' description in 'ep93xx_spi'
drivers/spi/spi-ep93xx.c:98: warning: Excess struct member 'dma_tx_data' description in 'ep93xx_spi'
Fixes: 3cfe73256905 ("spi: ep93xx: add DT support for Cirrus EP93xx")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
- add OF ID match table
- add device tree DMA request, so we can probe defer, in case DMA is not
ready yet
- drop DMA platform code
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use devm_pm_runtime_enable(), devm_request_irq() and
devm_spi_register_controller() to simplify code.
And also register a callback spi_geni_release_dma_chan() with
devm_add_action_or_reset(), to release dma channel in both error
and device detach path, which can make sure the release sequence is
consistent with the original one.
1. Unregister spi controller.
2. Free the IRQ.
3. Free DMA chans
4. Disable runtime PM.
So the remove function can also be removed.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20240912091701.3720857-1-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A patch for Qualcomm depends on some fixes.
|
|
Change the memcpy length to fix the out-of-bounds issue when writing the
data that is not 4 byte aligned to TX FIFO.
To reproduce the issue, write 3 bytes data to NOR chip.
dd if=3b of=/dev/mtd0
[ 36.926103] ==================================================================
[ 36.933409] BUG: KASAN: slab-out-of-bounds in nxp_fspi_exec_op+0x26ec/0x2838
[ 36.940514] Read of size 4 at addr ffff00081037c2a0 by task dd/455
[ 36.946721]
[ 36.948235] CPU: 3 UID: 0 PID: 455 Comm: dd Not tainted 6.11.0-rc5-gc7b0e37c8434 #1070
[ 36.956185] Hardware name: Freescale i.MX8QM MEK (DT)
[ 36.961260] Call trace:
[ 36.963723] dump_backtrace+0x90/0xe8
[ 36.967414] show_stack+0x18/0x24
[ 36.970749] dump_stack_lvl+0x78/0x90
[ 36.974451] print_report+0x114/0x5cc
[ 36.978151] kasan_report+0xa4/0xf0
[ 36.981670] __asan_report_load_n_noabort+0x1c/0x28
[ 36.986587] nxp_fspi_exec_op+0x26ec/0x2838
[ 36.990800] spi_mem_exec_op+0x8ec/0xd30
[ 36.994762] spi_mem_no_dirmap_read+0x190/0x1e0
[ 36.999323] spi_mem_dirmap_write+0x238/0x32c
[ 37.003710] spi_nor_write_data+0x220/0x374
[ 37.007932] spi_nor_write+0x110/0x2e8
[ 37.011711] mtd_write_oob_std+0x154/0x1f0
[ 37.015838] mtd_write_oob+0x104/0x1d0
[ 37.019617] mtd_write+0xb8/0x12c
[ 37.022953] mtdchar_write+0x224/0x47c
[ 37.026732] vfs_write+0x1e4/0x8c8
[ 37.030163] ksys_write+0xec/0x1d0
[ 37.033586] __arm64_sys_write+0x6c/0x9c
[ 37.037539] invoke_syscall+0x6c/0x258
[ 37.041327] el0_svc_common.constprop.0+0x160/0x22c
[ 37.046244] do_el0_svc+0x44/0x5c
[ 37.049589] el0_svc+0x38/0x78
[ 37.052681] el0t_64_sync_handler+0x13c/0x158
[ 37.057077] el0t_64_sync+0x190/0x194
[ 37.060775]
[ 37.062274] Allocated by task 455:
[ 37.065701] kasan_save_stack+0x2c/0x54
[ 37.069570] kasan_save_track+0x20/0x3c
[ 37.073438] kasan_save_alloc_info+0x40/0x54
[ 37.077736] __kasan_kmalloc+0xa0/0xb8
[ 37.081515] __kmalloc_noprof+0x158/0x2f8
[ 37.085563] mtd_kmalloc_up_to+0x120/0x154
[ 37.089690] mtdchar_write+0x130/0x47c
[ 37.093469] vfs_write+0x1e4/0x8c8
[ 37.096901] ksys_write+0xec/0x1d0
[ 37.100332] __arm64_sys_write+0x6c/0x9c
[ 37.104287] invoke_syscall+0x6c/0x258
[ 37.108064] el0_svc_common.constprop.0+0x160/0x22c
[ 37.112972] do_el0_svc+0x44/0x5c
[ 37.116319] el0_svc+0x38/0x78
[ 37.119401] el0t_64_sync_handler+0x13c/0x158
[ 37.123788] el0t_64_sync+0x190/0x194
[ 37.127474]
[ 37.128977] The buggy address belongs to the object at ffff00081037c2a0
[ 37.128977] which belongs to the cache kmalloc-8 of size 8
[ 37.141177] The buggy address is located 0 bytes inside of
[ 37.141177] allocated 3-byte region [ffff00081037c2a0, ffff00081037c2a3)
[ 37.153465]
[ 37.154971] The buggy address belongs to the physical page:
[ 37.160559] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x89037c
[ 37.168596] flags: 0xbfffe0000000000(node=0|zone=2|lastcpupid=0x1ffff)
[ 37.175149] page_type: 0xfdffffff(slab)
[ 37.179021] raw: 0bfffe0000000000 ffff000800002500 dead000000000122 0000000000000000
[ 37.186788] raw: 0000000000000000 0000000080800080 00000001fdffffff 0000000000000000
[ 37.194553] page dumped because: kasan: bad access detected
[ 37.200144]
[ 37.201647] Memory state around the buggy address:
[ 37.206460] ffff00081037c180: fa fc fc fc fa fc fc fc fa fc fc fc fa fc fc fc
[ 37.213701] ffff00081037c200: fa fc fc fc 05 fc fc fc 03 fc fc fc 02 fc fc fc
[ 37.220946] >ffff00081037c280: 06 fc fc fc 03 fc fc fc fc fc fc fc fc fc fc fc
[ 37.228186] ^
[ 37.232473] ffff00081037c300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.239718] ffff00081037c380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 37.246962] ==================================================================
[ 37.254394] Disabling lock debugging due to kernel taint
0+1 records in
0+1 records out
3 bytes copied, 0.335911 s, 0.0 kB/s
Fixes: a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Cc: stable@kernel.org
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://patch.msgid.link/20240911211146.3337068-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi_controller_is_slave() and spi_slave_abort() are all replaced,
so they can be removed.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-8-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use modern name target_abort.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-6-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use modern name function spi_target_abort().
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-5-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use modern name function spi_target_abort().
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-4-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use modern name function spi_target_abort().
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-3-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch to use modern name function spi_controller_is_target().
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://patch.msgid.link/20240910022618.1397-2-yangyingliang@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In spi_geni_remove(), the free_irq() sequence is different from that
on the probe error path. And the IRQ will still remain and it's interrupt
handler may use the dma channel after release dma channel and before free
irq, which is not secure, fix it.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20240909073141.951494-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's important to undo pm_runtime_use_autosuspend() with
pm_runtime_dont_use_autosuspend() at driver exit time unless driver
initially enabled pm_runtime with devm_pm_runtime_enable()
(which handles it for you).
Hence, switch to devm_pm_runtime_enable() to fix it, so the
pm_runtime_disable() in probe error path and remove function
can be removed.
Fixes: cfdab2cd85ec ("spi: spi-geni-qcom: Set an autosuspend delay of 250 ms")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20240909073141.951494-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The flexspi on imx8ulp only has 16 LUTs, different with others which
have up to 32 LUTs.
Add a separate compatible string and nxp_fspi_devtype_data to support
flexspi on imx8ulp.
Fixes: ef89fd56bdfc ("arm64: dts: imx8ulp: add flexspi node")
Cc: stable@kernel.org
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240905094338.1986871-4-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The flexspi on different SoCs may have different number of LUTs.
So involve lut_num in nxp_fspi_devtype_data to make distinguish.
This patch prepare for the adding of imx8ulp.
Fixes: ef89fd56bdfc ("arm64: dts: imx8ulp: add flexspi node")
Cc: stable@kernel.org
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20240905094338.1986871-3-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in
TCR register") doesn't implement the prescaler maximum as intended.
The maximum allowed value for i.MX93 should be 1 and for i.MX7ULP
it should be 7. So this needs also a adjustment of the comparison
in the scldiv calculation.
Fixes: 783bf5d09f86 ("spi: spi-fsl-lpspi: limit PRESCALE bit in TCR register")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20240905111537.90389-1-wahrenst@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace SET_RUNTIME_PM_OPS()/SET SYSTEM_SLEEP_PM_OPS() with their modern
RUNTIME_PM_OPS() and SYSTEM_SLEEP_PM_OPS() alternatives.
The combined usage of pm_ptr() and RUNTIME_PM_OPS/SYSTEM_SLEEP_PM_OPS()
allows the compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused annotations from the
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://patch.msgid.link/20240902184655.932699-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the of_device_id entry for "elgin,jg10309-01" was added, the
corresponding spi_device_id was forgotten, causing a warning message
during boot-up:
SPI driver spidev has no spi_device_id for elgin,jg10309-01
Fix module autoloading and shut up the warning by adding the missing
entry.
Fixes: 5f3eee1eef5d0edd ("spi: spidev: Add an entry for elgin,jg10309-01")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/54bbb9d8a8db7e52d13e266f2d4a9bcd8b42a98a.1725366625.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 8a0ec8c2d736 ("spi: Insert the missing pci_dev_put()before
return") added two uses of pci_dev_put() with an uninitialized dma_dev,
resulting in the following compiler warnings (or errors with
CONFIG_WERROR) when building with clang:
drivers/spi/spi-pxa2xx-pci.c:150:15: error: variable 'dma_dev' is uninitialized when used here [-Werror,-Wuninitialized]
150 | pci_dev_put(dma_dev);
| ^~~~~~~
drivers/spi/spi-pxa2xx-pci.c:228:15: error: variable 'dma_dev' is uninitialized when used here [-Werror,-Wuninitialized]
228 | pci_dev_put(dma_dev);
| ^~~~~~~
Commit 609d7ffdc421 ("spi: pxa2xx-pci: Balance reference count for PCI
DMA device") added a call to pci_dev_put() via
devm_add_action_or_reset() in case of failures, so the recent change was
incorrect for multiple reasons. Revert it altogether.
Fixes: 8a0ec8c2d736 ("spi: Insert the missing pci_dev_put()before return")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/CAMuHMdWNjo69_W6f+R9QJJOf8uF0htg2XazeS-yjugJv3UM+kg@mail.gmail.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20240902-spi-revert-8a0ec8c2d736-v1-1-928b829fed2b@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In zynq_qspi_exec_mem_op(), the temporary buffer is allocated with
kzalloc and then immediately initialized using memset to 0xff. To
optimize this, replace kzalloc with kmalloc, as the zeroing operation
is redundant and unnecessary.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20240814192839.345523-1-visitorckw@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sort the headers in alphabetic order in order to ease
the maintenance for this part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240902103203.2476576-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The commit had been applied twice as
0f245463b01e ("spi: ppc4xx: handle irq_of_parse_and_map() errors")
and
f1011ba20b83 ("spi: ppc4xx: handle irq_of_parse_and_map() errors")
This reverts commit f1011ba20b83da3ee70dcb4a6d9d282a718916fa.
Fixes: f1011ba20b83 ("spi: ppc4xx: handle irq_of_parse_and_map() errors")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20240902102853.2476165-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://patch.msgid.link/20240831094231.795024-1-liaochen4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the dev_err_probe() helper to simplify error handling during probe.
This also handle scenario, when EDEFER is returned and useless error
is printed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20240826121421.3384792-3-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_spi_alloc_host() so that there's no need to call
spi_controller_put() in the error path.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://patch.msgid.link/20240826121421.3384792-2-ruanjinjie@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The header file linux/platform_device.h is included
twice. Remove the last one.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240830075800.3541646-1-lihongbo22@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
intel_spi_populate_chip() use devm_kasprintf() to set pdata->name.
This can return a NULL pointer on failure but this returned value
is not checked.
Fixes: e58db3bcd93b ("spi: intel: Add default partition and name to the second chip")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20240830074106.8744-1-hanchunchao@inspur.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Jinjie Ruan <ruanjinjie@huawei.com>:
Fix uninitialized res in probe function.
|
