| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Drop the unnecessary "_sys" infix from the suspend PM ops.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial drivers should not be dropping characters themselves, but at
least drop the unused 'drop' parameter from the receive handler for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Drop the unnecessary WARN() in case the TTY buffers are ever full in
favour of a rate limited dev_err() which doesn't kill the machine when
panic_on_warn is set.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The receiver is supposed to be enabled in the startup() callback and not
in set_termios() which is called also during console setup.
This specifically avoids accepting input before the port has been opened
(and interrupts enabled), something which can also break the GENI
firmware (cancel fails and after abort, the "stale" counter handling
appears to be broken so that later input is not processed until twelve
chars have been received).
There also does not appear to be any need to keep the receiver disabled
while updating the port settings.
Since commit 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during
console writes") the calls to manipulate the secondary interrupts, which
were done without holding the port lock, can also lead to the receiver
being left disabled when set_termios() races with the console code (e.g.
when init opens the tty during boot). This can manifest itself as a
serial getty not accepting input.
The calls to stop and start rx in set_termios() can similarly race with
DMA completion and, for example, cause the DMA buffer to be unmapped
twice or the mapping to be leaked.
Fix this by only enabling the receiver during startup and while holding
the port lock to avoid racing with the console code.
Fixes: 6f3c3cafb115 ("serial: qcom-geni: disable interrupts during console writes")
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to wait for the DMA transfer to complete when cancelling the
rx command on stop_rx(). This specifically prevents the DMA completion
interrupt from firing after rx has been restarted, something which can
lead to an IOMMU fault and hosed rx when the interrupt handler unmaps
the DMA buffer for the new command:
qcom_geni_serial 988000.serial: serial engine reports 0 RX bytes in!
arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x563
arm-smmu 15000000.iommu: FSYNR0 = 00210013 [S1CBNDX=33 WNR PLVL=3]
Bluetooth: hci0: command 0xfc00 tx timeout
Bluetooth: hci0: Reading QCA version information failed (-110)
Also add the missing state machine reset which is needed in case
cancellation fails.
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Cc: stable@vger.kernel.org # 6.3
Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A commit adding back the stopping of tx on port shutdown failed to add
back the locking which had also been removed by commit e83766334f96
("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART
shutdown").
Holding the port lock is needed to serialise against the console code,
which may update the interrupt enable register and access the port
state.
Fixes: d8aca2f96813 ("tty: serial: qcom-geni-serial: stop operations in progress at shutdown")
Fixes: 947cc4ecc06c ("serial: qcom-geni: fix soft lockup on sw flow control and suspend")
Cc: stable@vger.kernel.org # 6.3
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 35781d8356a2eecaa6074ceeb80ee22e252fcdae.
Hibernation is not supported on Qualcomm platforms with mainline
kernels yet a broken vendor implementation for the GENI serial driver
made it upstream.
This is effectively dead code that cannot be tested and should just be
removed, but if these paths were ever hit for an open non-console port
they would crash the machine as the driver would fail to enable clocks
during restore() (i.e. all ports would have to be closed by drivers and
user space before hibernating the system to avoid this as a comment in
the code hinted at).
The broken implementation also added a random call to enable the
receiver in the port setup code where it does not belong and which
enables the receiver prematurely for console ports.
Fixes: 35781d8356a2 ("tty: serial: qcom-geni-serial: Add support for Hibernation feature")
Cc: stable@vger.kernel.org # 6.2
Cc: Aniket Randive <quic_arandive@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009145110.16847-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled console (KGDB/KDB) implementation must not call port setup
unconditionally as the port may already be in use by the console or a
getty.
Only make sure that the receiver is enabled, but do not enable any
device interrupts.
Fixes: d8851a96ba25 ("tty: serial: qcom-geni-serial: Add a poll_init() function")
Cc: stable@vger.kernel.org # 6.4
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20241009145110.16847-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending data using DMA at high baudrate (4 Mbdps in local test case) to
a device with small RX buffer which keeps asserting RTS after every received
byte, it is possible that the iMX UART driver would not recognize the falling
edge of RTS input signal and get stuck, unable to transmit any more data.
This condition happens when the following sequence of events occur:
- imx_uart_mctrl_check() is called at some point and takes a snapshot of UART
control signal status into sport->old_status using imx_uart_get_hwmctrl().
The RTSS/TIOCM_CTS bit is of interest here (*).
- DMA transfer occurs, the remote device asserts RTS signal after each byte.
The i.MX UART driver recognizes each such RTS signal change, raises an
interrupt with USR1 register RTSD bit set, which leads to invocation of
__imx_uart_rtsint(), which calls uart_handle_cts_change().
- If the RTS signal is deasserted, uart_handle_cts_change() clears
port->hw_stopped and unblocks the port for further data transfers.
- If the RTS is asserted, uart_handle_cts_change() sets port->hw_stopped
and blocks the port for further data transfers. This may occur as the
last interrupt of a transfer, which means port->hw_stopped remains set
and the port remains blocked (**).
- Any further data transfer attempts will trigger imx_uart_mctrl_check(),
which will read current status of UART control signals by calling
imx_uart_get_hwmctrl() (***) and compare it with sport->old_status .
- If current status differs from sport->old_status for RTS signal,
uart_handle_cts_change() is called and possibly unblocks the port
by clearing port->hw_stopped .
- If current status does not differ from sport->old_status for RTS
signal, no action occurs. This may occur in case prior snapshot (*)
was taken before any transfer so the RTS is deasserted, current
snapshot (***) was taken after a transfer and therefore RTS is
deasserted again, which means current status and sport->old_status
are identical. In case (**) triggered when RTS got asserted, and
made port->hw_stopped set, the port->hw_stopped will remain set
because no change on RTS line is recognized by this driver and
uart_handle_cts_change() is not called from here to unblock the
port->hw_stopped.
Update sport->old_status in __imx_uart_rtsint() accordingly to make
imx_uart_mctrl_check() detect such RTS change. Note that TIOCM_CAR
and TIOCM_RI bits in sport->old_status do not suffer from this problem.
Fixes: ceca629e0b48 ("[ARM] 2971/1: i.MX uart handle rts irq")
Cc: stable <stable@kernel.org>
Reviewed-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20241002184133.19427-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BUG: KASAN: slab-use-after-free in gsm_cleanup_mux+0x77b/0x7b0
drivers/tty/n_gsm.c:3160 [n_gsm]
Read of size 8 at addr ffff88815fe99c00 by task poc/3379
CPU: 0 UID: 0 PID: 3379 Comm: poc Not tainted 6.11.0+ #56
Hardware name: VMware, Inc. VMware Virtual Platform/440BX
Desktop Reference Platform, BIOS 6.00 11/12/2020
Call Trace:
<TASK>
gsm_cleanup_mux+0x77b/0x7b0 drivers/tty/n_gsm.c:3160 [n_gsm]
__pfx_gsm_cleanup_mux+0x10/0x10 drivers/tty/n_gsm.c:3124 [n_gsm]
__pfx_sched_clock_cpu+0x10/0x10 kernel/sched/clock.c:389
update_load_avg+0x1c1/0x27b0 kernel/sched/fair.c:4500
__pfx_min_vruntime_cb_rotate+0x10/0x10 kernel/sched/fair.c:846
__rb_insert_augmented+0x492/0xbf0 lib/rbtree.c:161
gsmld_ioctl+0x395/0x1450 drivers/tty/n_gsm.c:3408 [n_gsm]
_raw_spin_lock_irqsave+0x92/0xf0 arch/x86/include/asm/atomic.h:107
__pfx_gsmld_ioctl+0x10/0x10 drivers/tty/n_gsm.c:3822 [n_gsm]
ktime_get+0x5e/0x140 kernel/time/timekeeping.c:195
ldsem_down_read+0x94/0x4e0 arch/x86/include/asm/atomic64_64.h:79
__pfx_ldsem_down_read+0x10/0x10 drivers/tty/tty_ldsem.c:338
__pfx_do_vfs_ioctl+0x10/0x10 fs/ioctl.c:805
tty_ioctl+0x643/0x1100 drivers/tty/tty_io.c:2818
Allocated by task 65:
gsm_data_alloc.constprop.0+0x27/0x190 drivers/tty/n_gsm.c:926 [n_gsm]
gsm_send+0x2c/0x580 drivers/tty/n_gsm.c:819 [n_gsm]
gsm1_receive+0x547/0xad0 drivers/tty/n_gsm.c:3038 [n_gsm]
gsmld_receive_buf+0x176/0x280 drivers/tty/n_gsm.c:3609 [n_gsm]
tty_ldisc_receive_buf+0x101/0x1e0 drivers/tty/tty_buffer.c:391
tty_port_default_receive_buf+0x61/0xa0 drivers/tty/tty_port.c:39
flush_to_ldisc+0x1b0/0x750 drivers/tty/tty_buffer.c:445
process_scheduled_works+0x2b0/0x10d0 kernel/workqueue.c:3229
worker_thread+0x3dc/0x950 kernel/workqueue.c:3391
kthread+0x2a3/0x370 kernel/kthread.c:389
ret_from_fork+0x2d/0x70 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:257
Freed by task 3367:
kfree+0x126/0x420 mm/slub.c:4580
gsm_cleanup_mux+0x36c/0x7b0 drivers/tty/n_gsm.c:3160 [n_gsm]
gsmld_ioctl+0x395/0x1450 drivers/tty/n_gsm.c:3408 [n_gsm]
tty_ioctl+0x643/0x1100 drivers/tty/tty_io.c:2818
[Analysis]
gsm_msg on the tx_ctrl_list or tx_data_list of gsm_mux
can be freed by multi threads through ioctl,which leads
to the occurrence of uaf. Protect it by gsm tx lock.
Signed-off-by: Longlong Xia <xialonglong@kylinos.cn>
Cc: stable <stable@kernel.org>
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240926130213.531959-1-xialonglong@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
font.data may not initialize all memory spaces depending on the implementation
of vc->vc_sw->con_font_get. This may cause info-leak, so to prevent this, it
is safest to modify it to initialize the allocated memory space to 0, and it
generally does not affect the overall performance of the system.
Cc: stable@vger.kernel.org
Reported-by: syzbot+955da2d57931604ee691@syzkaller.appspotmail.com
Fixes: 05e2600cb0a4 ("VT: Bump font size limitation to 64x128 pixels")
Signed-off-by: Jeongjun Park <aha310510@gmail.com>
Link: https://lore.kernel.org/r/20241010174619.59662-1-aha310510@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver updates for 6.12-rc1.
Nothing major in here, just nice forward progress in the slow cleanup
of the serial apis, and lots of other driver updates and fixes.
Included in here are:
- serial api updates from Jiri to make things more uniform and sane
- 8250_platform driver cleanups
- samsung serial driver fixes and updates
- qcom-geni serial driver fixes from Johan for the bizarre UART
engine that that chip seems to have. Hopefully it's in a better
state now, but hardware designers still seem to come up with more
ways to make broken UARTS 40+ years after this all should have
finished.
- sc16is7xx driver updates
- omap 8250 driver updates
- 8250_bcm2835aux driver updates
- a few new serial driver bindings added
- other serial minor driver updates
All of these have been in linux-next for a long time with no reported
problems"
* tag 'tty-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (65 commits)
tty: serial: samsung: Fix serial rx on Apple A7-A9
tty: serial: samsung: Fix A7-A11 serial earlycon SError
tty: serial: samsung: Use bit manipulation macros for APPLE_S5L_*
tty: rp2: Fix reset with non forgiving PCIe host bridges
serial: 8250_aspeed_vuart: Enable module autoloading
serial: qcom-geni: fix polled console corruption
serial: qcom-geni: disable interrupts during console writes
serial: qcom-geni: fix console corruption
serial: qcom-geni: introduce qcom_geni_serial_poll_bitfield()
serial: qcom-geni: fix arg types for qcom_geni_serial_poll_bit()
soc: qcom: geni-se: add GP_LENGTH/IRQ_EN_SET/IRQ_EN_CLEAR registers
serial: qcom-geni: fix false console tx restart
serial: qcom-geni: fix fifo polling timeout
tty: hvc: convert comma to semicolon
mxser: convert comma to semicolon
serial: 8250_bcm2835aux: Fix clock imbalance in PM resume
serial: sc16is7xx: convert bitmask definitions to use BIT() macro
serial: sc16is7xx: fix copy-paste errors in EFR_SWFLOWx_BIT constants
serial: sc16is7xx: remove SC16IS7XX_MSR_DELTA_MASK
serial: xilinx_uartps: Make cdns_rs485_supported static
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext support from Tejun Heo:
"This implements a new scheduler class called ‘ext_sched_class’, or
sched_ext, which allows scheduling policies to be implemented as BPF
programs.
The goals of this are:
- Ease of experimentation and exploration: Enabling rapid iteration
of new scheduling policies.
- Customization: Building application-specific schedulers which
implement policies that are not applicable to general-purpose
schedulers.
- Rapid scheduler deployments: Non-disruptive swap outs of scheduling
policies in production environments"
See individual commits for more documentation, but also the cover letter
for the latest series:
Link: https://lore.kernel.org/all/20240618212056.2833381-1-tj@kernel.org/
* tag 'sched_ext-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext: (110 commits)
sched: Move update_other_load_avgs() to kernel/sched/pelt.c
sched_ext: Don't trigger ops.quiescent/runnable() on migrations
sched_ext: Synchronize bypass state changes with rq lock
scx_qmap: Implement highpri boosting
sched_ext: Implement scx_bpf_dispatch[_vtime]_from_dsq()
sched_ext: Compact struct bpf_iter_scx_dsq_kern
sched_ext: Replace consume_local_task() with move_local_task_to_local_dsq()
sched_ext: Move consume_local_task() upward
sched_ext: Move sanity check and dsq_mod_nr() into task_unlink_from_dsq()
sched_ext: Reorder args for consume_local/remote_task()
sched_ext: Restructure dispatch_to_local_dsq()
sched_ext: Fix processs_ddsp_deferred_locals() by unifying DTL_INVALID handling
sched_ext: Make find_dsq_for_dispatch() handle SCX_DSQ_LOCAL_ON
sched_ext: Refactor consume_remote_task()
sched_ext: Rename scx_kfunc_set_sleepable to unlocked and relocate
sched_ext: Add missing static to scx_dump_data
sched_ext: Add missing static to scx_has_op[]
sched_ext: Temporarily work around pick_task_scx() being called without balance_scx()
sched_ext: Add a cgroup scheduler which uses flattened hierarchy
sched_ext: Add cgroup support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
"This is the "last" part of the support for the new nbcon consoles.
Where "nbcon" stays for "No Big console lock CONsoles" aka not under
the console_lock.
New callbacks are added to struct console:
- write_thread() for flushing nbcon consoles in task context.
- write_atomic() for flushing nbcon consoles in atomic context,
including NMI.
- con->device_lock() and device_unlock() for taking the driver
specific lock, for example, port->lock.
New printk-specific kthreads are created:
- per-console kthreads which get responsible for flushing normal
priority messages on nbcon consoles.
- thread which gets responsible for flushing normal priority messages
on all consoles when CONFIG_RT enabled.
The new callbacks are called under a special per-console lock which
has already been added back in v6.7. It allows to distinguish three
severities: normal, emergency, and panic. A context with a higher
priority could take over the ownership when it is safe even in the
middle of handling a record. The panic context could do it even when
it is not safe. But it is allowed only for the final desperate flush
before entering the infinite loop.
The new lock helps to flush the messages directly in emergency and
panic contexts. But it is not enough in all situations:
- console_lock() is still need for synchronization against boot
consoles.
- con->device_lock() is need for synchronization against other
operations on the same HW, e.g. serial port speed setting,
non-printk related read/write.
The dependency on con->device_lock() is mutual. Any code taking the
driver specific lock has to acquire the related nbcon console context
as well. For example, see the new uart_port_lock() API. It provides
the necessary synchronization against emergency and panic contexts
where the messages are flushed only under the new per-console lock.
Maybe surprisingly, a quite tricky part is the decision how to flush
the consoles in various situations. It has to take into account:
- message priority: normal, emergency, panic
- scheduling context: task, atomic, deferred_legacy
- registered consoles: boot, legacy, nbcon
- threads are running: early boot, suspend, shutdown, panic
- caller: printk(), pr_flush(), printk_flush_in_panic(),
console_unlock(), console_start(), ...
The primary decision is made in printk_get_console_flush_type(). It
creates a hint what the caller should do:
- flush nbcon consoles directly or via the kthread
- call the legacy loop (console_unlock()) directly or via irq_work
The existing behavior is preserved for the legacy consoles. The only
exception is that they are not longer flushed directly from printk()
in panic() before CPUs are stopped. But this blocking happens only
when at least one nbcon console is registered. The motivation is to
increase a chance to produce the crash dump. They legacy consoles
might create a deadlock in compare with nbcon consoles. The nbcon
console should allow to see the messages even when the crash dump
fails.
There are three possible ways how nbcon consoles are flushed:
- The per-nbcon-console kthread is responsible for flushing messages
added with the normal priority. This is the default mode.
- The legacy loop, aka console_unlock(), is used when there is still
a boot console registered. There is no easy way how to match an
early console driver with a nbcon console driver. And the
console_lock() provides the only reliable serialization at the
moment.
The legacy loop uses either con->write_atomic() or
con->write_thread() callbacks depending on whether it is allowed to
schedule. The atomic variant has to be used from printk().
- In other situations, the messages are flushed directly using
write_atomic() which can be called in any context, including NMI.
It is primary needed during early boot or shutdown, in emergency
situations, and panic.
The emergency priority is used by a code called within
nbcon_cpu_emergency_enter()/exit(). At the moment, it is used in four
situations: WARN(), Oops, lockdep, and RCU stall reports.
Finally, there is no nbcon console at the moment. It means that the
changes should _not_ modify the existing behavior. The only exception
is CONFIG_RT which would force offloading the legacy loop, for normal
priority context, into the dedicated kthread"
* tag 'printk-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (54 commits)
printk: Avoid false positive lockdep report for legacy printing
printk: nbcon: Assign nice -20 for printing threads
printk: Implement legacy printer kthread for PREEMPT_RT
tty: sysfs: Add nbcon support for 'active'
proc: Add nbcon support for /proc/consoles
proc: consoles: Add notation to c_start/c_stop
printk: nbcon: Show replay message on takeover
printk: Provide helper for message prepending
printk: nbcon: Rely on kthreads for normal operation
printk: nbcon: Use thread callback if in task context for legacy
printk: nbcon: Relocate nbcon_atomic_emit_one()
printk: nbcon: Introduce printer kthreads
printk: nbcon: Init @nbcon_seq to highest possible
printk: nbcon: Add context to usable() and emit()
printk: Flush console on unregister_console()
printk: Fail pr_flush() if before SYSTEM_SCHEDULING
printk: nbcon: Add function for printers to reacquire ownership
printk: nbcon: Use raw_cpu_ptr() instead of open coding
printk: Use the BITS_PER_LONG macro
lockdep: Mark emergency sections in lockdep splats
...
|
|
Apple's older A7-A9 SoCs seems to use bit 3 in UTRSTAT as RXTO, which is
enabled by bit 11 in UCON.
Access these bits in addition to the original RXTO and RXTO enable bits,
to allow serial rx to function on A7-A9 SoCs. This change does not
appear to affect the A10 SoC and up.
Tested-by: Janne Grunau <j@jannau.net>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-4-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Apple's earlier SoCs, like A7-A11, requires 32-bit writes for the serial
port. Otherwise, a SError happens when writing to UTXH (+0x20). This only
manifested in earlycon as reg-io-width in the device tree is consulted
for normal serial writes.
Change the iotype of the port to UPIO_MEM32, to allow the serial port to
function on A7-A11 SoCs. This change does not appear to affect Apple M1 and
above.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Tested-by: Janne Grunau <j@jannau.net>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20240911050741.14477-3-towinchenmi@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards")
Cc: stable <stable@kernel.org>
Suggested-by: Jim Quinlan <james.quinlan@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded based
on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20240903131503.961178-1-liaochen4@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The polled UART operations are used by the kernel debugger (KDB, KGDB),
which can interrupt the kernel at any point in time. The current
Qualcomm GENI implementation does not really work when there is on-going
serial output as it inadvertently "hijacks" the current tx command,
which can result in both the initial debugger output being corrupted as
well as the corruption of any on-going serial output (up to 4k
characters) when execution resumes:
0190: abcdefghijklmnopqrstuvwxyz0123456789 0190: abcdefghijklmnopqrstuvwxyz0123456789
0191: abcdefghijklmnop[ 50.825552] sysrq: DEBUG
qrstuvwxyz0123456789 0191: abcdefghijklmnopqrstuvwxyz0123456789
Entering kdb (current=0xffff53510b4cd280, pid 640) on processor 2 due to Keyboard Entry
[2]kdb> go
omlji3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t72r2rp
o9n976k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawavu:t7t8s8s8r2r2q0q0p
o9n9n8ml6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav v u:u:t9t0s4s4rq0p
o9n9n8m8m7l7l6k6k5j5j40q0p p o
o9n9n8m8m7l7l6k6k5j5j4i4i3h3h2g2g1f1f0e0ezdzdycycxbxbwawav :t8t9s4s4r4r4q0q0p
Fix this by making sure that the polled output implementation waits for
the tx fifo to drain before cancelling any on-going longer transfers. As
the polled code cannot take any locks, leave the state variables as they
are and instead make sure that the interrupt handler always starts a new
tx command when there is data in the write buffer.
Since the debugger can interrupt the interrupt handler when it is
writing data to the tx fifo, it is currently not possible to fully
prevent losing up to 64 bytes of tty output on resume.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Disable the GENI interrupts during console writes to reduce the risk of
having interrupt handlers spinning on the port lock on other cores for
extended periods of time.
This can, for example, reduce the total amount of time spent in the
interrupt handler during boot of the x1e80100 CRD by up to a factor nine
(e.g. from 274 ms to 30 ms) while the worst case processing time drops
from 19 ms to 8 ms.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-8-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm serial console implementation is broken and can lose
characters when the serial port is also used for tty output.
Specifically, the console code only waits for the current tx command to
complete when all data has already been written to the fifo. When there
are on-going longer transfers this often means that console output is
lost when the console code inadvertently "hijacks" the current tx
command instead of starting a new one.
This can, for example, be observed during boot when console output that
should have been interspersed with init output is truncated:
[ 9.462317] qcom-snps-eusb2-hsphy fde000.phy: Registered Qcom-eUSB2 phy
[ OK ] Found device KBG50ZNS256G KIOXIA Wi[ 9.471743ndows.
[ 9.539915] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
Add a new state variable to track how much data has been written to the
fifo and use it to determine when the fifo and shift register are both
empty. This is needed since there is currently no other known way to
determine when the shift register is empty.
This in turn allows the console code to interrupt long transfers without
losing data.
Note that the oops-in-progress case is similarly broken as it does not
cancel any active command and also waits for the wrong status flag when
attempting to drain the fifo (TX_FIFO_NOT_EMPTY_EN is only set when
cancelling a command leaves data in the fifo).
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Fixes: 9e957a155005 ("serial: qcom-geni: Don't cancel/abort if we can't get the port lock")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With a small modification the qcom_geni_serial_poll_bit() function
could be used to poll more than just a single bit. Let's generalize
it. We'll make the qcom_geni_serial_poll_bit() into just a wrapper of
the general function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.5.Ic6411eab8d9d37acc451705f583fb535cd6dadb2@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "offset" passed in should be unsigned since it's always a positive
offset from our memory mapped IO.
The "field" should be u32 since we're anding it with a 32-bit value
read from the device.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240610152420.v4.4.I24a0de52dd7336908df180fa6b698e001f3aff82@changeid
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
addressed an issue with stalled tx after the console code interrupted
the last bytes of a tx command by reenabling the watermark interrupt if
there is data in write buffer. This can however break software flow
control by re-enabling tx after the user has stopped it.
Address the original issue by not clearing the CMD_DONE flag after
polling for command completion. This allows the interrupt handler to
start another transfer when the CMD_DONE interrupt has not been disabled
due to flow control.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Fixes: 663abb1a7a7f ("tty: serial: qcom_geni_serial: Fix UART hang")
Cc: stable@vger.kernel.org # 4.17
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The qcom_geni_serial_poll_bit() can be used to wait for events like
command completion and is supposed to wait for the time it takes to
clear a full fifo before timing out.
As noted by Doug, the current implementation does not account for start,
stop and parity bits when determining the timeout. The helper also does
not currently account for the shift register and the two-word
intermediate transfer register.
A too short timeout can specifically lead to lost characters when
waiting for a transfer to complete as the transfer is cancelled on
timeout.
Instead of determining the poll timeout on every call, store the fifo
timeout when updating it in set_termios() and make sure to take the
shift and intermediate registers into account. Note that serial core has
already added a 20 ms margin to the fifo timeout.
Also note that the current uart_fifo_timeout() interface does
unnecessary calculations on every call and did not exist in earlier
kernels so only store its result once. This facilitates backports too as
earlier kernels can derive the timeout from uport->timeout, which has
since been removed.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240906131336.23625-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull bpf/master to receive baebe9aaba1e ("bpf: allow passing struct
bpf_iter_<type> as kfunc arguments") and related changes in preparation for
the DSQ iterator patchset.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Allow the 'active' attribute to list nbcon consoles.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20240904120536.115780-15-john.ogness@linutronix.de
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20240903023001.491055-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/r/20240903023754.493568-1-nichen@iscas.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During review Ulf Hansson discovered a clock imbalance in the recently
introduced PM resume code. The driver should enable the clock only in
case it has been disabled in suspend before. In order to make the
conditions easier to read, refactor this into a separate function.
Reported-by: Ulf Hansson <ulf.hansson@linaro.org>
Closes: https://lore.kernel.org/linux-arm-kernel/CAPDyKFoJh3j8xSeXZ9o031YZLTCDYVA+dgvURuwozjDpU_aauA@mail.gmail.com/
Fixes: 0e1d8780526f ("serial: 8250_bcm2835aux: add PM suspend/resume support")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240818174936.88372-1-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that bit definition comments were cleaned up, convert bitmask
definitions to use BIT() macro for clarity.
Convert SC16IS7XX_IIR_ID_MASK to use GENMASK() macro -
- while at that, realign comments.
Compose SC16IS7XX_LSR_BRK_ERROR_MASK using aforementioned constants,
instead of open-coding it, and remove now unneeded comments.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/8b45a01e-7cc5-4d53-b467-c6680bc51ef4@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Comments attached to bits 0 and 1 incorrectly referenced bits 2 and 3,
which don't match the datasheet - fix them.
At the same time remove comments for individual constants, as they add
nothing to the definitions themselves.
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/2986a485-935d-4ab2-9a16-4a85288aa15a@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This definition isn't used anywhere anymore, let's delete it.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/91a9aa22-47b7-449a-a7ad-877ce1b6402e@camlingroup.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sparse tool complains as follows:
drivers/tty/serial/xilinx_uartps.c:222:21: warning:
symbol 'cdns_rs485_supported' was not declared. Should it be static?
This symbol is not used outside xilinx_uartps.c, so marks it static.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20240819120107.3884973-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We do embedd struct fown_struct into struct file letting it take up 32
bytes in total. We could tweak struct fown_struct to be more compact but
really it shouldn't even be embedded in struct file in the first place.
Instead, actual users of struct fown_struct should allocate the struct
on demand. This frees up 24 bytes in struct file.
That will have some potentially user-visible changes for the ownership
fcntl()s. Some of them can now fail due to allocation failures.
Practically, that probably will almost never happen as the allocations
are small and they only happen once per file.
The fown_struct is used during kill_fasync() which is used by e.g.,
pipes to generate a SIGIO signal. Sending of such signals is conditional
on userspace having set an owner for the file using one of the F_OWNER
fcntl()s. Such users will be unaffected if struct fown_struct is
allocated during the fcntl() call.
There are a few subsystems that call __f_setown() expecting
file->f_owner to be allocated:
(1) tun devices
file->f_op->fasync::tun_chr_fasync()
-> __f_setown()
There are no callers of tun_chr_fasync().
(2) tty devices
file->f_op->fasync::tty_fasync()
-> __tty_fasync()
-> __f_setown()
tty_fasync() has no additional callers but __tty_fasync() has. Note
that __tty_fasync() only calls __f_setown() if the @on argument is
true. It's called from:
file->f_op->release::tty_release()
-> tty_release()
-> __tty_fasync()
-> __f_setown()
tty_release() calls __tty_fasync() with @on false
=> __f_setown() is never called from tty_release().
=> All callers of tty_release() are safe as well.
file->f_op->release::tty_open()
-> tty_release()
-> __tty_fasync()
-> __f_setown()
__tty_hangup() calls __tty_fasync() with @on false
=> __f_setown() is never called from tty_release().
=> All callers of __tty_hangup() are safe as well.
From the callchains it's obvious that (1) and (2) end up getting called
via file->f_op->fasync(). That can happen either through the F_SETFL
fcntl() with the FASYNC flag raised or via the FIOASYNC ioctl(). If
FASYNC is requested and the file isn't already FASYNC then
file->f_op->fasync() is called with @on true which ends up causing both
(1) and (2) to call __f_setown().
(1) and (2) are the only subsystems that call __f_setown() from the
file->f_op->fasync() handler. So both (1) and (2) have been updated to
allocate a struct fown_struct prior to calling fasync_helper() to
register with the fasync infrastructure. That's safe as they both call
fasync_helper() which also does allocations if @on is true.
The other interesting case are file leases:
(3) file leases
lease_manager_ops->lm_setup::lease_setup()
-> __f_setown()
Which in turn is called from:
generic_add_lease()
-> lease_manager_ops->lm_setup::lease_setup()
-> __f_setown()
So here again we can simply make generic_add_lease() allocate struct
fown_struct prior to the lease_manager_ops->lm_setup::lease_setup()
which happens under a spinlock.
With that the two remaining subsystems that call __f_setown() are:
(4) dnotify
(5) sockets
Both have their own custom ioctls to set struct fown_struct and both
have been converted to allocate a struct fown_struct on demand from
their respective ioctls.
Interactions with O_PATH are fine as well e.g., when opening a /dev/tty
as O_PATH then no file->f_op->open() happens thus no file->f_owner is
allocated. That's fine as no file operation will be set for those and
the device has never been opened. fcntl()s called on such things will
just allocate a ->f_owner on demand. Although I have zero idea why'd you
care about f_owner on an O_PATH fd.
Link: https://lore.kernel.org/r/20240813-work-f_owner-v2-1-4e9343a79f9f@kernel.org
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Introduce uart_port_set_cons() as a wrapper to set @cons of a
uart_port. The wrapper sets @cons under the port lock in order
to prevent @cons from disappearing while another context is
holding the port lock. This is necessary for a follow-up
commit relating to the port lock wrappers, which rely on @cons
not changing between lock and unlock.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Théo Lebrun <theo.lebrun@bootlin.com> # EyeQ5, AMBA-PL011
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240820063001.36405 |
