| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add new driver version to support tas2563 & tas2781 qfn chip
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20241104100055.48-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On a system with wcd937x, rxmacro and Qualcomm audio DSP, which is pretty
common set of devices on Qualcomm platforms, and due to the order of how
DAPM widgets are powered on (they are sorted), there is a small time window
when wcd937x chip is online and expects the flow of incoming data but
rxmacro is not yet online. When wcd937x is programmed to receive data
via AUX port then its AUX PDM watchdog is enabled in
wcd937x_codec_enable_aux_pa(). If due to some reasons the rxmacro and
soundwire machinery are delayed to start streaming data, then there is
a chance for this AUX PDM watchdog to reset the wcd937x codec. Such event
is not logged as a message and only wcd937x IRQ counter is increased
however there could be a lot of other reasons for that IRQ.
There is a similar opportunity for such delay during DAPM widgets power
down sequence.
If wcd937x codec reset happens on the start of the playback, then there
will be no sound and if such reset happens at the end of a playback then
it may generate additional clicks and pops noises.
On qrb4210 RB2 board without any debugging bits the wcd937x resets are
sometimes observed at the end of a playback though not always.
With some debugging messages or with some tracing enabled the AUX PDM
watchdog resets the wcd937x codec at the start of a playback and there
is no sound output at all.
In this patch:
- TIMEOUT_SEL bit in PDM_WD_CTL2 register is set to increase the watchdog
reset delay to 100ms which eliminates the AUX PDM watchdog IRQs on
qrb4210 RB2 board completely and decreases the number of unwanted clicks
noises;
- HOLD_OFF bit postpones triggering such watchdog IRQ till wcd937x codec
reset which usually happens at the end of a playback. This allows to
actually output some sound in case of debugging.
Cc: Adam Skladowski <a39.skl@gmail.com>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Cc: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-3-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The wcd937x supports also AUX input but the control that sets correct
soundwire port for this is missing. This control is required for audio
playback, for instance, on qrb4210 RB2 board as well as on other
SoCs.
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Reported-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Suggested-by: Adam Skladowski <a39.skl@gmail.com>
Suggested-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20241022033132.787416-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If devm_gpiod_get_optional() fails, we need to disable previously enabled
regulators, as done in the other error handling path of the function.
Also, gpiod_set_value_cansleep(, 1) needs to be called to undo a
potential gpiod_set_value_cansleep(, 0).
If the "reset" gpio is not defined, this additional call is just a no-op.
This behavior is the same as the one already in the .remove() function.
Fixes: 11b9cd748e31 ("ASoC: cs42l51: add reset management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/a5e5f4b9fb03f46abd2c93ed94b5c395972ce0d1.1729975570.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Disable IRQs from rt5640_cancel_work(), this fixes a crash caused by
the IRQ never getting freed when the driver is unbound from the i2c_client
with jack-detection active:
[ 193.138780] rt5640 i2c-rt5640: ASoC: unknown pin LDO2
[ 193.138830] rt5640 i2c-rt5640: ASoC: unknown pin MICBIAS1
[ 193.671218] BUG: kernel NULL pointer dereference, address: 0000000000000078
[ 193.671239] #PF: supervisor read access in kernel mode
[ 193.671248] #PF: error_code(0x0000) - not-present page
...
[ 193.671531] ? asm_exc_page_fault+0x22/0x30
[ 193.671551] ? rt5640_jack_inserted+0x10/0x80 [snd_soc_rt5640]
[ 193.671574] rt5640_detect_headset+0x93/0x130 [snd_soc_rt5640]
[ 193.671596] rt5640_jack_work+0x93/0x355 [snd_soc_rt5640]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241024215612.92147-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
clk_stop_timeout should be increased to 900ms to fix clock stop issue.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://patch.msgid.link/cd26275d9fc54374a18dc016755cb72d@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Turns out some registers of pre-2.5 version of rxmacro codecs are not
located at the expected offsets but 0xc further away in memory. So far
the detected registers are CDC_RX_RX2_RX_PATH_SEC7 and
CDC_RX_RX2_RX_PATH_DSM_CTL.
CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n) macro incorrectly generates the address
0x540 for RX2 but it should be 0x54C and it also overwrites
CDC_RX_RX2_RX_PATH_SEC7 which is located at 0x540.
The same goes for CDC_RX_RXn_RX_PATH_SEC7(rx, n).
Fix this by introducing additional rxn_reg_stride2 offset. For 2.5 version
and above this offset will be equal to 0.
With such change the corresponding RXn() macros will generate the same
values for 2.5 codec version for all RX paths and the same old values
for pre-2.5 version for RX0 and RX1. However for the latter case with
RX2 path it will also add rxn_reg_stride2 on top.
While at this, also remove specific if-check for INTERP_AUX from
rx_macro_digital_mute() and rx_macro_enable_interp_clk(). These if-check
was used to handle such special offset for AUX interpolator but since
CDC_RX_RXn_RX_PATH_SEC7(rx, n) and CDC_RX_RXn_RX_PATH_DSM_CTL(rx, n)
macros will generate the correst addresses of dsm register, they are no
longer needed.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patch.msgid.link/20241016221049.1145101-1-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Change my contact e-mail in pcm3060 driver and MAINTAINERS
Signed-off-by: Kirill Marinushkin <k.marinushkin@gmail.com>
Cc: Kirill Marinushkin <kmarinushkin@birdec.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-sound@vger.kernel.org
Link: https://patch.msgid.link/20241016215810.1544222-1-k.marinushkin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The variable slot_found is being initialized to zero and inside
a for-loop is being checked if it's reached MAX_NUM_CH, however,
this is currently impossible since slot_found is never changed.
In a previous loop a similar coding pattern is used and slot_found
is being incremented. It appears the increment of slot_found is
missing from the loop, so fix the code by adding in the increment.
Fixes: 6a8e1d46f062 ("ASoC: max98388: add amplifier driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://patch.msgid.link/20241010182032.776280-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Added proper error handling for register value check that
return -EPERM when register value does not meet expected condition
Signed-off-by: Zhu Jun <zhujun2@cmss.chinamobile.com>
Link: https://patch.msgid.link/20241009073938.7472-1-zhujun2@cmss.chinamobile.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly high amount of changes in this round, partly because of my
vacation in the last weeks. But all changes are small and nothing
looks worrisome.
The biggest LOCs is MAINTAINERS updates, and there is a core change
for card-ID string creation for non-ASCII inputs. Others are rather
device-specific, such as new quirks and device IDs for ASoC, usual
HD-audio and USB-audio quirks and fixes, as well as regression fixes
in HD-audio HDMI audio and Conexant codec"
* tag 'sound-6.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (39 commits)
ALSA: hda/conexant: Fix conflicting quirk for System76 Pangolin
ALSA: line6: add hw monitor volume control to POD HD500X
ALSA: gus: Fix some error handling paths related to get_bpos() usage
ALSA: hda: Add missing parameter description for snd_hdac_stream_timecounter_init()
ALSA: usb-audio: Add native DSD support for Luxman D-08u
ALSA: core: add isascii() check to card ID generator
MAINTAINERS: ALSA: use linux-sound@vger.kernel.org list
Revert "ALSA: hda: Conditionally use snooping for AMD HDMI"
ASoC: intel: sof_sdw: Add check devm_kasprintf() returned value
ASoC: imx-card: Set card.owner to avoid a warning calltrace if SND=m
ASoC: dt-bindings: davinci-mcasp: Fix interrupts property
ASoC: qcom: sm8250: add qrb4210-rb2-sndcard compatible string
ASoC: dt-bindings: qcom,sm8250: add qrb4210-rb2-sndcard
ALSA: hda: fix trigger_tstamp_latched
ALSA: hda/realtek: Add a quirk for HP Pavilion 15z-ec200
ALSA: hda/generic: Drop obsoleted obey_preferred_dacs flag
ALSA: hda/generic: Unconditionally prefer preferred_dacs pairs
ALSA: silence integer wrapping warning
ASoC: Intel: soc-acpi: arl: Fix some missing empty terminators
ASoC: Intel: soc-acpi-intel-rpl-match: add missing empty item
...
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
|
|
default regs values
CDC_RX_BCL_VBAT_RF_PROC1 is listed twice and its default value
is 0x2a which is overwriten by its next occurence in rx_defaults[].
The second one should be missing CDC_RX_BCL_VBAT_RF_PROC2 instead
and its default value is expected 0x0.
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Link: https://patch.msgid.link/20240925043823.520218-2-alexey.klimov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Changes cs35l45_get_clk_freq_id() function data type from unsigned int
to int. This function is returns a positive index value if successful
or a negative error code if unsuccessful.
Functionally there should be no difference as long as the unsigned int
return is interpreted as an int, however it should be corrected for
readability.
Signed-off-by: Ricardo Rivera-Matos <rriveram@opensource.cirrus.com>
Link: https://patch.msgid.link/20240919151654.197337-1-rriveram@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A fairly big update at this time, both in core and driver sides.
The core received rewrites in PCM buffer allocation handling and
locking optimizations, PCM rate updates followed by lots of cleanups.
In ASoC side, the legacy Intel drivers have been deprecated by AVS
drivers which leaded to the significant amount of code reduction.
SoundWire driver updates and other cleanups contributed more code
reduction, too.
USB-audio driver received a large cleanup of its big quirk table, and
the old snd_print*() API usages in many legacy drivers are replaced
with the standard print API.
Here are some highlights:
Core:
- More optimized locking in ALSA control code
- Rewrites of memalloc helpers for better DMA API usage
- Drop of obsoleted vmalloc PCM buffer helper API
- Continued MIDI2 UMP updates
- Support of a new user-space driven timer instance
- Update for more PCM support rates and cleanups
- Xrun counter report in the proc files
ASoC:
- Continued simplification and cleanup works for ASoC
- Extensive cleanups and refactoring of the Soundwire drivers
- Removal of Intel machine support obsoleted by the AVS driver
- Lots of DT schema conversions
- Machine support for many AMD and Intel x86 platforms
- Support for AMD ACP 7.1, Mediatek MT6367 and MT8365, Realtek
RTL1320 SoundWire and rev C, and Texas Instruments TAS2563
USB-audio:
- Add support of multiple control interfaces
- A large rewrite of quirk table with macros
- Support for RME Digiface USB
HD-audio:
- Cleanup of quirk code for Samsung Galaxy laptops
- Clean up of detection of Cirrus codecs
- C-Media CM9825 HD-audio codec support
Others:
- Rewrites to standard print API in a lot of legacy drivers"
* tag 'sound-6.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (410 commits)
ASoC: topology: Fix redundant logical jump
ASoC: tas2781: Add Calibration Kcontrols for Chromebook
ASoC: amd: acp: refactor SoundWire machine driver code
ASoC: sdw_utils/intel: move soundwire endpoint parsing helper functions
ASoC: sdw_util/intel: move soundwire endpoint and dai link structures
ASoC: intel: sof_sdw: rename soundwire parsing helper functions
ASoC: intel: sof_sdw: rename soundwire endpoint and dailink structures
ASoC: atmel: mchp-pdmc: Retain Non-Runtime Controls
ALSA: hda/realtek: Add support for Galaxy Book2 Pro (NP950XEE)
ASoC: mediatek: mt7986-afe-pcm: Remove redundant error message
ALSA: memalloc: Use proper DMA mapping API for x86 S/G buffer allocations
ALSA: memalloc: Use proper DMA mapping API for x86 WC buffer allocations
ALSA: usb-audio: Add logitech Audio profile quirk
ASoc: mediatek: mt8365: Remove unneeded assignment
ASoC: Intel: ARL: Add entry for HDMI-In capture support to non-I2S codec boards.
ASoC: Intel: sof_rt5682: Add HDMI-In capture with rt5682 support for ARL.
ASoC: SOF: Intel: hda: remove common_hdmi_codec_drv
ASoC: Intel: sof_pcm512x: do not check common_hdmi_codec_drv
ASoC: Intel: ehl_rt5660: do not check common_hdmi_codec_drv
ASoC: Intel: skl_hda_dsp_generic: use common module for DAI links
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few last-minute ASoC fixes and MAINTAINERS update.
All look small, obvious and nice-to-have fixes for 6.11-final"
* tag 'sound-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: meson: axg-card: fix 'use-after-free'
ASoC: codecs: avoid possible garbage value in peb2466_reg_read()
MAINTAINERS: update Pierre Bossart's email and role
ASoC: tas2781: fix to save the dsp bin file name into the correct array in case name_prefix is not NULL
ASoC: Intel: soc-acpi-intel-mtl-match: add missing empty item
ASoC: Intel: soc-acpi-intel-lnl-match: add missing empty item
|
|
Pull 6.11 fixes to 6.12-devel branch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.12
This is a very large set of changes, almost all in drivers rather than
the core. Even with the addition of several quite large drivers the
overall diffstat is negative thanks to the removal of some old Intel
board support which has been obsoleted by the AVS driver, helped a bit
by some factoring out into helpers (especially around the Soundwire
machine drivers for x86).
Highlights include:
- More simplifications and cleanups throughout the subsystem from
Morimoto-san.
- Extensive cleanups and refactoring of the Soundwire drivers to make
better use of helpers.
- Removal of Intel machine support obsoleted by the AVS driver.
- Lots of DT schema conversions.
- Machine support for many AMD and Intel x86 platforms.
- Support for AMD ACP 7.1, Mediatek MT6367 and MT8365, Realtek RTL1320
SoundWire and rev C, and Texas Instruments TAS2563
|
|
Add calibration related kcontrol for speaker impedance calibration and
speaker leakage check for Chromebook.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20240911232739.1509-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Clang static checker (scan-build) warning:
sound/soc/codecs/peb2466.c:232:8:
Assigned value is garbage or undefined [core.uninitialized.Assign]
232 | *val = tmp;
| ^ ~~~
When peb2466_read_byte() fails, 'tmp' will have a garbage value.
Add a judgemnet to avoid this problem.
Fixes: 227f609c7c0e ("ASoC: codecs: Add support for the Infineon PEB2466 codec")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://patch.msgid.link/20240911115448.277828-1-suhui@nfschina.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix typos in comments.
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Kreimer <algonell@gmail.com>
Link: https://patch.msgid.link/20240910211302.8909-1-algonell@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all drivers below sound/soc to use .remove(), with the eventual
goal to drop struct platform_driver::remove_new(). As .remove() and
.remove_new() have the same prototypes, conversion is done by just
changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/20240909151230.909818-2-u.kleine-koenig@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The TLV320DAC3100 Audio DAC has 25 built-in digital audio processing blocks
(PRBs). Each of these PRBs has a static filter structure with programmable
coefficients. Once a PRB is selected for use by the DAC, its filter
coefficients can be configured via a dedicated set of registers.
Define a new optional firmware which can be loaded by the TLV320DAC driver.
This firmware describes a full set of filter coefficients for all blocks
used by the various PRBs.
The firmware's binary format is heavily inspired by the one used in the
peb2466 driver. It includes a version marker to allow for potential
evolutions of the format.
Note that adaptive filtering is not supported i.e. filter coefficients are
loaded once before power-on and then cannot be changed while the DAC is
powered. This is why only page A coefficients are modified. Page B
coefficients are only used for adaptive filtering.
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://patch.msgid.link/20240906-tlv320-filter-v1-1-6955f53ff435@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
case name_prefix is not NULL
fix to save the dsp bin file name into the correct array, coef_binaryname,
instead of rca_binaryname, in case name_prefix is not NULL.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20240907001540.944-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last PR for 6.11, at least for this level of amount.
In addition to the usual HD-audio quirks, there are more changes in
ASoC, but all look small and device-specific fixes, and nothing stands
out. The only slightly big change is sunxi I2S fix, which looks quite
safe to apply, too"
* tag 'sound-6.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek - Fix inactive headset mic jack for ASUS Vivobook 15 X1504VAP
ALSA: hda/realtek: Support mute LED on HP Laptop 14-dq2xxx
ALSA: hda/realtek: Enable Mute Led for HP Victus 15-fb1xxx
ALSA: hda/realtek: extend quirks for Clevo V5[46]0
ASoC: codecs: lpass-va-macro: set the default codec version for sm8250
ALSA: hda: add HDMI codec ID for Intel PTL
ALSA: hda/realtek: add patch for internal mic in Lenovo V145
ASoC: sunxi: sun4i-i2s: fix LRCLK polarity in i2s mode
ASoC: amd: yc: Add a quirk for MSI Bravo 17 (D7VEK)
ASoC: mediatek: mt8188-mt6359: Modify key
ASoc: SOF: topology: Clear SOF link platform name upon unload
ALSA: hda/conexant: Add pincfg quirk to enable top speakers on Sirius devices
ASoC: SOF: ipc: replace "enum sof_comp_type" field with "uint32_t"
ASoC: fix module autoloading
ASoC: tda7419: fix module autoloading
ASoC: google: fix module autoloading
ASoC: intel: fix module autoloading
ASoC: tegra: Fix CBB error during probe()
ASoC: dapm: Fix UAF for snd_soc_pcm_runtime object
ASoC: Intel: soc-acpi-cht: Make Lenovo Yoga Tab 3 X90F DMI match less strict
...
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: ying zuxin <11154159@vivo.com>
Link: https://patch.msgid.link/20240906084841.19248-1-yingzuxin@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
IEC958-3 defines sampling rate up to 768 kHz.
Such rates maybe used with high bandwidth IEC958 links, such as eARC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-13-8371948d3921@baylibre.com
|
|
The cs35l34 adds a useless rate constraint on startup.
It does not set SNDRV_PCM_RATE_KNOT and the rates set are already a subset
of the ones provided in the constraint list, so it is a no-op.
>From the rest of the code, it is likely HW supports more than the 32, 44.1
and 48kHz listed in CS35L34_RATES but there is no way to know for sure
without proper documentation.
Keep the driver as it is for now and just drop the useless constraint.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-12-8371948d3921@baylibre.com
|
|
The custom rate constraint list was necessary to support 12kHz and 24kHz.
These rates are now available through SNDRV_PCM_RATE_12000 and
SNDRV_PCM_RATE_24000.
Use them and drop the custom rate constraint rule.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-8-8371948d3921@baylibre.com
|
|
The custom rate constraint list was necessary to support 12kHz and 24kHz.
These rates are now available through SNDRV_PCM_RATE_12000 and
SNDRV_PCM_RATE_24000.
Use them and drop the custom rate constraint rule.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-7-8371948d3921@baylibre.com
|
|
The custom rate constraint list was necessary to support 12kHz and 24kHz.
These rates are now available through SNDRV_PCM_RATE_12000 and
SNDRV_PCM_RATE_24000.
Use them and drop the custom rate constraint rule.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: David Rhodes <drhodes@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240905-alsa-12-24-128-v1-6-8371948d3921@baylibre.com
|
|
Add the support of MT6357 PMIC audio codec.
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://patch.msgid.link/20240226-audio-i350-v8-1-e80a57d026ce@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Support multiple endpoints on TLV320AIC32x4 codec port when
used in of_graph context.
This patch allows to share the codec port between two CPU DAIs.
Example:
Custom STM32MP157C board uses TLV320AIC32x4 audio codec. This codec
is connected to two serial audio interfaces, which are configured
either as rx or tx.
>From AsoC point of view the topolgy is the following:
// 2 CPU DAIs (SAI2A/B), 1 Codec (TLV320AIC32x4)
Playback: CPU-A-DAI(slave) -> (master)CODEC-DAI/port0
Record: CPU-B-DAI(slave) <- (master)CODEC-DAI/port0
In the DT two endpoints have to be associated to the codec port:
tlv320aic32x4_port: port {
tlv320aic32x4_tx_endpoint: endpoint@0 {
remote-endpoint = <&sai2a_endpoint>;
};
tlv320aic32x4_rx_endpoint: endpoint@1 {
remote-endpoint = <&sai2b_endpoint>;
};
};
However, when the audio graph card parses the codec nodes, it expects
to find DAI interface indexes matching the endpoints indexes.
The current patch forces the use of DAI id 0 for both endpoints,
which allows to share the codec DAI between the two CPU DAIs
for playback and capture streams respectively.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patch.msgid.link/20240830231007.205707-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return devm_of_clk_add_hw_provider() in order to transfer the error, if it
fails due to resource allocation failure or device tree clock provider
registration failure.
Cc: stable@vger.kernel.org
Fixes: ebbfabc16d23 ("ASoC: rt5682: Add CCF usage for providing I2S clks")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Link: https://patch.msgid.link/20240830143154.3448004-1-make24@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch added the support for version C.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://patch.msgid.link/20240902090845.1862354-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a test case for commit bb4485562f59 ("ASoC: cs-amp-lib: Ignore
empty UEFI calibration entries").
Any entries in the calibration blob that have calTime==0 are empty
entries. So they must not be returned by a lookup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20240830144819.118362-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sm8250 and sc7280 have lpass codec version 1.0, as these are very old
platforms, they do not have a reliable way to get the codec version
from core_id registers.
On codec versions below 2.0, even though the core_id registers are
available to read, the values of these registers are not unique to be
able to determine the version of the codec dynamically.
Add the version info into of_data, so that driver does not need to use
core_id registers to get version number for such situations.
Fixes: 378918d59181 ("ASoC: codecs: lpass-macro: add helpers to get codec version")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://patch.msgid.link/20240816091210.50172-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull 6.11 devel branch for applying further updates for Cirrus codecs
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Read temperature of the speaker and expose it via hwmon interface, which
will be later used during calibration of speaker protection algorithms.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240809110122.137761-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It became a bit larger collection of fixes than wished at this time,
but all changes are small and mostly device-specific fixes that should
be fairly safe to apply.
Majority of fixes are about ASoC for AMD SOF, Cirrus codecs, lpass,
etc, in addition to the usual HD-audio quirks / fixes"
* tag 'sound-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (22 commits)
ALSA: hda: hda_component: Fix mutex crash if nothing ever binds
ALSA: hda/realtek: support HP Pavilion Aero 13-bg0xxx Mute LED
ALSA: hda/realtek: Fix the speaker output on Samsung Galaxy Book3 Ultra
ASoC: cs-amp-lib: Ignore empty UEFI calibration entries
ASoC: cs-amp-lib-test: Force test calibration blob entries to be valid
ALSA: hda/realtek - FIxed ALC285 headphone no sound
ALSA: hda/realtek - Fixed ALC256 headphone no sound
ASoC: allow module autoloading for table board_ids
ASoC: allow module autoloading for table db1200_pids
ALSA: hda: cs35l56: Don't use the device index as a calibration index
ALSA: seq: Skip event type filtering for UMP events
ALSA: hda/realtek: Enable mute/micmute LEDs on HP Laptop 14-ey0xxx
ASoC: SOF: amd: Fix for acp init sequence
ASoC: amd: acp: fix module autoloading
ASoC: mediatek: mt8188: Mark AFE_DAC_CON0 register as volatile
ASoC: codecs: wcd937x: Fix missing de-assert of reset GPIO
ASoC: SOF: mediatek: Add missing board compatible
ASoC: MAINTAINERS: Drop Banajit Goswami from Qualcomm sound drivers
ASoC: SOF: amd: Fix for incorrect acp error register offsets
ASoC: SOF: amd: move iram-dram fence register programming sequence
...
|
|
Replace devm_kzalloc and scnprintf with devm_kstrdup.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://patch.msgid.link/20240824060503.1259-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://patch.msgid.link/20240826084924.368387-5-liaochen4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add MODULE_DEVICE_TABLE(), so modules could be properly autoloaded
based on the alias from of_device_id table.
Signed-off-by: Liao Chen <liaochen4@huawei.com>
Link: https://patch.msgid.link/20240826084924.368387-4-liaochen4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of the fixes for the Intel bards overlap with development work that
removed old boards.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Eliminate the fdtoverlay command duplication in scripts/Makefile.lib
- Fix 'make compile_commands.json' for external modules
- Ensure scripts/kconfig/merge_config.sh handles missing newlines
- Fix some build errors on macOS
* tag 'kbuild-fixes-v6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: fix typos "prequisites" to "prerequisites"
Documentation/llvm: turn make command for ccache into code block
kbuild: avoid scripts/kallsyms parsing /dev/null
treewide: remove unnecessary <linux/version.h> inclusion
scripts: kconfig: merge_config: config files: add a trailing newline
Makefile: add $(srctree) to dependency of compile_commands.json target
kbuild: clean up code duplication in cmd_fdtoverlay
|
|
If the timestamp of a calibration entry is 0 it is an unused entry and
must be ignored.
Some end-products reserve EFI space for calibration entries by shipping
with a zero-filled EFI file. When searching the file for calibration
data the driver must skip the empty entries. The timestamp of a valid
entry is always non-zero.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 1cad8725f2b9 ("ASoC: cs-amp-lib: Add helpers for factory calibration data")
Link: https://patch.msgid.link/20240822133544.304421-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's now possible to declare instances of struct regmap_config as
const data.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20240822145535.336407-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For a normal calibration blob the calTarget values must be non-zero and
unique, and the calTime values must be non-zero. Don't rely on
get_random_bytes() to be random enough to guarantee this. Force the
calTarget and calTime values to be valid while retaining randomness
in the values.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 177862317a98 ("ASoC: cs-amp-lib: Add KUnit test for calibration helpers")
Link: https://patch.msgid.link/20240822115725.259568-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
