// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2021 - All Rights Reserved
* Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp13-clks.h>
#include <dt-bindings/reset/stm32mp13-resets.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
};
};
arm-pmu {
compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>;
interrupt-parent = <&intc>;
};
firmware {
optee {
method = "smc";
compatible = "linaro,optee-tz";
interrupt-parent = <&intc>;
interrupts = <GIC_PPI 15 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
};
scmi: scmi {
compatible = "linaro,scmi-optee";
#address-cells = <1>;
#size-cells = <0>;
linaro,optee-channel-id = <0>;
scmi_clk: protocol@14 {
reg = <0x14>;
#clock-cells = <1>;
};
scmi_reset: protocol@16 {
reg = <0x16>;
#reset-cells = <1>;
};
scmi_voltd: protocol@17 {
reg = <0x17>;
scmi_regu: regulators {
#address-cells = <1>;
#size-cells = <0>;
scmi_reg11: regulator@0 {
reg = <VOLTD_SCMI_REG11>;
regulator-name = "reg11";
};
scmi_reg18: regulator@1 {
reg = <VOLTD_SCMI_REG18>;
regulator-name = "reg18";
};
scmi_usb33: regulator@2 {
reg = <VOLTD_SCMI_USB33>;
regulator-name = "usb33";
};
};
};
};
};
intc: interrupt-controller@a0021000 {
compatible = "arm,cortex-a7-gic";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0xa0021000 0x1000>,
<0xa0022000 0x2000>;
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&intc>;
always-on;
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
ranges;
timers2: timer@40000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40000000 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "global";
clocks = <&rcc TIM2_K>;
clock-names = "int";
dmas = <&dmamux1 18 0x400 0x1>,
<&dmamux1 19 0x400 0x1>,
<&dmamux1 20 0x400 0x1>,
<&dmamux1 21 0x400 0x1>,
<&dmamux1 22 0x400 0x1>;
