// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2017, The Linux Foundation. All rights reserved.
*/
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/of_address.h>
#include <linux/phy/phy.h>
#include <linux/platform_device.h>
#include <linux/regulator/consumer.h>
#include <linux/reset.h>
#include <linux/slab.h>
#include "phy-qcom-qmp.h"
#include "phy-qcom-qmp-pcs-misc-v3.h"
#include "phy-qcom-qmp-pcs-usb-v4.h"
#include "phy-qcom-qmp-pcs-usb-v5.h"
/* QPHY_SW_RESET bit */
#define SW_RESET BIT(0)
/* QPHY_POWER_DOWN_CONTROL */
#define SW_PWRDN BIT(0)
/* QPHY_START_CONTROL bits */
#define SERDES_START BIT(0)
#define PCS_START BIT(1)
/* QPHY_PCS_STATUS bit */
#define PHYSTATUS BIT(6)
/* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
/* DP PHY soft reset */
#define SW_DPPHY_RESET BIT(0)
/* mux to select DP PHY reset control, 0:HW control, 1: software reset */
#define SW_DPPHY_RESET_MUX BIT(1)
/* USB3 PHY soft reset */
#define SW_USB3PHY_RESET BIT(2)
/* mux to select USB3 PHY reset control, 0:HW control, 1: software reset */
#define SW_USB3PHY_RESET_MUX BIT(3)
/* QPHY_V3_DP_COM_PHY_MODE_CTRL register bits */
#define USB3_MODE BIT(0) /* enables USB3 mode */
#define DP_MODE BIT(1) /* enables DP mode */
/* QPHY_PCS_AUTONOMOUS_MODE_CTRL register bits */
#define ARCVR_DTCT_EN BIT(0)
#define ALFPS_DTCT_EN BIT(1)
#define ARCVR_DTCT_EVENT_SEL BIT(4)
/* QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR register bits */
#define IRQ_CLEAR BIT(0)
/* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
#define CLAMP_EN BIT(0) /* enables i/o clamp_n */
#define PHY_INIT_COMPLETE_TIMEOUT 10000
struct qmp_phy_init_tbl {
unsigned int offset;
unsigned int val;
/*
* mask of lanes for which this register is written
* for cases when second lane needs different values
*/
u8 lane_mask;
};
#define QMP_PHY_INIT_CFG(o, v) \
{ \
.offset = o, \
.val = v, \
.lane_mask = 0xff, \
}
#define QMP_PHY_INIT_CFG_LANE(o, v, l) \
{ \
.offset = o, \
.val = v, \
.lane_mask = l, \
}
/* set of registers with offsets different per-PHY */
enum qphy_reg_layout {
/* PCS registers */
QPHY_SW_RESET,
QPHY_START_CTRL,
QPHY_PCS_STATUS,
QPHY_PCS_AUTONOMOUS_MODE_CTRL,
QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
QPHY_PCS_POWER_DOWN_CONTROL,
/* Keep last to ensure regs_layout arrays are properly initialized */
QPHY_LAYOUT_SIZE
};
static const unsigned int qmp_v3_usb3phy_regs_layout[QPHY_LAYOUT_SIZE] = {
[QPHY_SW_RESET] = QPHY_V3_PCS_SW_RESET,
[QPHY_START_CTRL] = QPHY_V3_PCS_START_CONTROL,
[QPHY_PCS_STATUS] = QPHY_V3_PCS_PCS_STATUS,
[QPHY_PCS_AUTONOMOUS_MODE_CTRL] = QPHY_V3_PCS_AUTONOMOUS_MODE_CTRL,
[